Search Documents

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By F. Letowski

A column reactor was applied for leaching with simultaneous flotation a complex sulfide ore in ferric sulfate-solution under oxygen pressure. Elemental sulfur and the flotable, nonreacted sulfides were collected in the froth and separated from the insoluble, nonflotable gangue minerals and solid particles formed during pressure leaching. The two-stage laboratory unit, built from Corning-glass elements is described. Results of the continuous leaching/flotation experiments conducted under 20-40 psig of oxygen pressure are presented, as are supplementary batch leaching experiments with iron precipitation under 150 psig oxygen pressure. High zinc extraction to solution and near total accumulation of lead sulfate in the nonflotable fraction are easily attainable. Relatively poor flotation of pyrite is probably caused by the partial oxidation of its sulfidic sulfur to sulfate.

Jan 1, 1988

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By G. F. Friel, J. C. Edwards, C. C. Hwang

In the implementation of a mine fire alarm and location strategy, the Interpretation of the fire signature Is Important. Smoke and CO are the two dominant fire signatures, and many mine fire detection systems utilize sensors which respond to smoke or CO through a diffusion mode or a mechanical pump mode. The fire signature may be modified during its transport along airways and at crosscuts. The modification occurs through dilution of the contaminants. In this Investigation, computer codes were employed to compute the effects of contaminant dilution on the contaminant signature when a straight flow passage has one dead-end crosscut. The model predicted the airflow within always and the entrainment of contaminants into the crosscut from the airway. One application of the model is to determine the most suitable location for CO detectors for early mine fire detection.

Jan 1, 1995

By Robert S. Holmes

The U. S. Army Corps of Engineers Explosive Excavation Research Office (EERO) of Livermore, California, has been engaged in research and development of excavation techniques using both nuclear and conventional explosives since 1962. Prior to July 1971, this organization was designated the U. S. Army Corps of Engineers Nuclear Cratering Group. The EERO mission is performed as part of the joint Atomic Energy Commission -Corps of Engineers nuclear excavation research pro-gram. During the period 1962-1969, the Corps executed many cratering explosions using spherical charges of up to 85 tons of nitromethane to model nuclear excavation concepts and to develop design criteria for the nuclear cratering explosions. The experience gained in these modeling tests suggested that explosive excavation using large chemical explosive charges could be applied to excavation projects as an economical substitute for traditional excavation techniques. Consequently, the Corps' research program was broadened in 1969 to include development of chemical explosive excavation as a construction tool. The term "explosive excavation" denotes the use of large buried explosive charges to produce an excavation by fracturing the material and casting it into a desired configuration. In its simplest form, this technology involves detonation of a single explosive charge buried at the proper depth to produce a crater which is roughly hyperbolic in cross section. The types of craters produced by various depths of burial are illustrated by Figure 1. Single or Multiple rows of charges are used to excavate linear cuts required for water conveyance or navigation channels. .More complex explosive excavations include small craft harbors, railroad and highway cuts, and removal of W1denvater rock barriers to navigation. While the literature indicates widespread use of large explosions in the (1) ERRO is a field activity of the Waterway Experiment Station, Vicksburg, Mississippi

Jan 1, 1971

By B. Cavender

Mining managers trying to rapidly reduce production costs tend to implement a traditional set of topdown managerial practices: reductions in production volume, employee layoffs, renegotiation of supplier contracts, cancellation of employee training, restrictions on travel, reductions in office supplies, and so forth. While these practices do reduce costs, the benefits are often limited in both magnitude and duration, and the workforce is usually left demoralized. Successful cost-cutters take a different approach. They make the continuous reduction of costs a priority for all members of the organization, whether managers or workers. The culture of these firms emphasizes the commitment, voluntarily given, of individuals and work groups to this goal. Cost-cutting practices often reject all of the traditional methods mentioned above, but are far more numerous, innovative and successful. This culture of cost reduction is the result of a set of leadership competencies that establish direction for the organization, align the organization's various constituencies with this direction, and motivate and inspire the organization. Cost reduction then becomes a routine task rather than a heroic achievement.

Jan 1, 2002

By Rui Xiang Yang, Cong Li, Jia Zeng, Rong Liang Zhang, Wei Zhang, Chao Fan Tang

This research took the roasted products obtained by leaching copper (Cu) refining slag using waste acids and roasting leaching residues with calcium oxide (CaO) as raw materials and used oxidative leaching to extract Cu from roasted products using waste acids. Influences of the leaching temperature, liquid–solid ratio, and sulfuric acid ( H2SO4) concentration in waste acids on the leaching rate of Cu in the oxidative leaching process of roasted products using waste acids were investigated. The unreacted-core shrinking model of heterogeneous reactions was adopted to reveal the leaching kinetics of Cu in the oxidative leaching process of roasted products using waste acids. Results show that the leaching rate of Cu reaches 91.68% when the leaching temperature, liquid–solid ratio, H2SO4 concentration in waste acids, and injected airflow are 80 ℃, 8:1, 1.5 mol/L, and 200 mL/min, respectively. If the leaching temperature is below 80 ℃, the leaching process of Cu is controlled by the solid-film diffusion, and the apparent activation energy Ea is 11.0835 kJ/mol; at a leaching temperature above 80 ℃, the leaching process of Cu is governed by the interfacial chemical reaction, with an apparent activation energy Ea of 42.3183 kJ/mol. The liquid–solid ratio can positively influence the reaction rate constant. The apparent order of the leaching reaction of Cu is 0.632.

Jan 11, 2023

By Anthony Harding

In a world of technology and electronic communication, it is easy to forget what engineers do best with a problem: sitting around a table, exchanging views and ideas with sketches and respecting everyone?s view. This was the approach adopted in the project to arrive at a solution for the cross passage opening sup-port for the Seattle University Link Extension. Schedule and space constraints usually impede concurrent cross passage excavation and tunnel boring machine (TBM) operation. And where the space is constrained, opening support solutions that maximize available cross sections are of great benefit. While there are a number of solutions that minimize space, some of these solutions can require expensive steelwork and extensive drilling and fixing. However, following a detailed round-the-table discussion of the options and constraints, it was identified that a shotcrete shell would not only limit obstruction of the space during installation, but also permit easy installation, particularly around services, and avoid costly steelwork and drilling and fixing.

By E. H. Partelpoeg, B. G. Belew

In 1990, the Chino Smelter completed the construction of a plant designed to recover metal values and water from smelter scrubber effluent. Equipment was installed to maximize effluent recycling and minimize costs. The process utilizes magnesium hydroxide as a neutralizing agent which has the advantage of precipitating copper from solution with minimum generation of solid reaction products. The neutralized stream is clarified, with solids recycled to the smelter for metal recovery while the clarified effluent is recycled to the concentrator for use as process water.

Jan 1, 1992

By Jacek Kolacz, Knut Lyng Sandvik

Fine grinding in an air swept and a grate discharge ball mill working in closed circuit with a forced vortex air classifier has been investigated in continuous laboratory scale. Minerals with different physical properties were ground down to 40, 20, and 10 micron top size. The shape of the product particle size distribution curve was investigated and specific surface (BET) was measured. During production of material with top size of 40 microns in an air swept mill, the capacity was up to 25% higher when compared to a grate discharge mill. This difference dropped to 180A during production of 10 micron top size material. A corresponding decrease in power consumption was observed. An important finding is that by regulation of the air flow rate through the mill, it is possible to achieve products with different specific surfaces and particle size distribution curve steepness. During production of the 10 pm material, the specific surface could be varied in the range 3 to 4.5 m2/g. Such powders could hardly be produced in a grate discharge mill because fine particles coated the grinding media and the lining. On the other hand the internal classification in the air swept mill kept the size distribution of the mill content relatively free of fines. This prevented a similar slowing-down of the air swept grinding process.

Jan 1, 1995

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

By G. E. S. Valadao

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake pore microstructure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 µm, length of 500 µm and height of 4000 µm. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: I) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method, 2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4) some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By S. C. Sun

A study(1) on the sulfuric acid extraction of alumina from some Pennsylvania ferruginous clays indicated that the published electrolytic method(2)(3) seems to be more efficient than the known chemical methods (4-9) for removing iron from the leach liquor. The main disadvantages of the chemical methods are the consumption of excessive amounts of reagents and/or the precipitation of prohibitive amounts of aluminum. In the electrolytic method, iron is deposited on the mercury cathode, while aluminum is not and remains in solution. This method, however, had been handicapped by the lack of an effective and economical way to purify the contaminated mercury cathode.(7)(l0). Described herein is a scheme for cleaning the mercury cathode, and for recycling the clean mercury back into the electrolytic cell. Armed with such an apparatus, the effects of applied potential, temperature, and operation time on the electrolytic separation of iron from aluminum sulfate solutions were determined. For the sake of comparing results, a term, removability, was coined to represent the percentage of iron amalgamated per unit height of electrolyte (cm.), per unit surface area of cathode (cm.2), per unit of operation time (second).

Jan 1, 1968

By J. Raatikainen, I. Auranen

"INTRODUCTION Sorting technology has advanced rapidly recently. Of the two possibilities particle sorting has advanced especially in introducing new sensors and the use of multiple sensors. The analyzing and computing lead times have also shortened. This has made it a viable technology option for many applications but not for the most important sorting task at a mine; the run-of mine ore. Bulk sorting, however, has advanced in smaller steps, even if the technology has the capability to tackle the run-of-mine ore and offers a high potential to bring mines substantial economic benefits. The sensors, which are useful are restricted by the difficult operating conditions or by the ore characteristics. One of the important features of run-of-mine sorting technology is the major material handling infrastructure required. The capital expenditure can be substantial requiring good understanding of the sortability curve (grade-recovery curve) behavior of the ore. This paper discusses one industrial case, where substantial amount of data measured from the ore feed belt has been obtained. This data was then analyzed for the grade recovery curves obtainable from that ore with sorting. EXPERIMENTAL The XRF measurement used was the FCA device from IMA Engineering (Fig.1). It is a specially built version of XRF designed to operate with coarse material. The measurement was situated at the main belt conveyor taking ore from the primary crusher to the stockpile. The crushed ore was about 80% -300 mm at a capacity of 1100-1200 tph (Fig.2). Measurement times were varied from 30 seconds to a minute. Measurements were obtained over several months.As the XRF is a surface distribution measuring technique, the measurement was first tested upon accuracy and reproducibility against plant daily wet chemical assays and against on-line Courier feed analysis. As there is a varying delay in the ore stockpile, the delay time was used as a variant in the validation. Different measurement times were tested for accuracy. A one minute measurement time gave a total measurement relative standard error, which was both for Cu and Ni below 3%. The results showed also very robust correlations; for Cu, the correlation coefficient was R > 0,94 for one minute measurements over three months and R > 0,86 for Ni respectively. Fig 3. Shows a measurement period of two hours showing substantial feed grade variations (given as relative value; 1.0 represents the mean value during the measurement month)."

Jan 1, 2018

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Gerald H. Luttrell, Jaisen N. Kohmuench, Michael J. Mankosa

A new separator, known as the Hydrofloat cell, has been developed to overcome limitations of traditional flotation cells in recovering coarse particles. In this process, small air bubbles are introduced into a hindered "teeter" bed of fluidized solids to create light bubble-particle aggregates that can be separated based on differences in density. Laboratory tests conducted with coarse phosphate feeds indicate that the Hydrofloat cell is capable of increasing BPL recoveries by nearly 20% over conventional flotation methods. Based on these encouraging results, a pilot-scale Hydrofloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the plus 35 mesh plant feed can be increased by more than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the plus 16 mesh particles in the Hydrofloat concentrate. This article describes the theoretical basis for the development of the Hydrofloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 1999