Search Documents

By M. W. Brandt

In the November 1957 issue of "Chemical Process Engineering," a British publications, there appeared an article entitled "Correct Selection of Drying Equipment." The author wrote as follows "Whether batch drying or continuous drying' methods are applied, the basis of efficient drying is heat distribution, control of rate of heat input, and heat transference from heating medium to the particles of the material to be dried." The author continues: "Because the efficiency of direct dryers, such as hot air or hot gas dryers, increases with rising inlet temperature of the drying air or gas when exhaust temperature remains fixed, the highest practical drying temperature should be used. Exhaust air should leave the dryer at the lowest possible temperature, but as fully saturated with moisture as possible." It is certainly conceivable that the author of this article by outlining the basic requirements for efficient drying methods has unwittingly given the reasons why fluidized drying is rapidly being adopted for so many industrail applications, including the dryingof fine coal. An examination in greater detail of the individual basic requirements for efficient drying as outlined by the author is perhaps the most logical starting point.

Jan 1, 1958

By G. T. Adel

As a prerequisite to removing mineral matter from coal by any physical separation technique, the mineral and coal particles must be sufficiently liberated. In the case of the production of superclean (< 2% ash), low-sulfur products, the appropriate liberation size may be less than 10 µm. Unfortunately, much of the liberation data obtained at these fine sizes is only qualitative due to the lack of appropriate instrumentation. In the present work, computerized image analysis has been used to characterize several common eastern U.S. coals. In most cases, it has been found that micronizing of the coal is necessary in order to achieve sufficient liberation for deep cleaning. Liberation analyses of the products from the microbubble column flotation process have been used to distinguish problems in liberation from problems in selectivity, especially as they pertain to pyrite rejection.

Jan 1, 1989

By D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming mineral. A polymeric depressant is then added to attach to this re-surfaced mineral. Nearly 200 flotation tests with a 11 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother-collector system, grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1994

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, M. RAJU, GANESH SHETTY

With the depletion of high-grade iron ore resources, the utilization of existing low-grade iron ores, fines and tailings with effective beneficiation is inevitable to meet the iron and steel industry’s required specifications and demand. JSW Steel Limited is operating a 17-mtpa beneficiation plant at its Vijayanagar site in Bellary in Karnataka, which produces nearly 50 to 54 percent concentrate as sinter-grade fines. The sinter base mix consists of iron ore fines that are smaller than 10 mm, with 41 percent smaller than 0.150 mm; washed ore that is generally smaller than 3 mm and bigger than 0.150 mm, with 3 to 9 percent smaller than 0.150 mm; beneficiation plant concentrate, with 97 percent smaller than 0.150 mm; limestone; dolomite; coke breeze; lime; sinter return fines; direct reduced iron (DRI) fines; and micropellets produced from steel plant waste. Using more washed ore in the sinter base mix affects the sinter quality. Ball formation in the mixing and nodulizing drum is an important step in sinter making and requires sufficient quantity of smaller than 0.150 mm fines. Optimization of fines in the sinter base was carried out by replacing the smaller than 10 mm iron ore fines with washed ore. Size analysis, study of the granulation index (G index) and optimization of moisture with respect to sinter bed permeability were carried out to optimize the proportion of smaller than 0.150 mm fines in the sinter base mix as adhering material. This study explores the optimization of fines in the sinter base mix for ball formation to achieve higher sinter quality and productivity with higher sinter bed permeability.

By Ingvar Janelid

During recent years, numerous articles have been published regarding theories and practical applications of sublevel caving. The reason is the great interest this method has created through its possibilities of standardizing and mechanizing operations and equipment. Other advantages are that the method can be adapted to orebodies of different shape, size, strength etc., and especially that working conditions can be made safe and relatively comfortable since all work is carried out in drifts. As is well known, the disadvantages or sublevel caving are that ore recovery hardly exceeds 85-90 % if waste rock dilution is to be kept below 20-30 %. Therefore, the main research and development work has been concentrated on parameters which can affect and reduce these disadvantages. This paper deals only with principles and problems which apply to large, massive orebodies. The problems with narrow, vertical or inclined orebodies are so different that they require a special handling. In my opinion, the intense research and development work during recent years, combined with practical experience, has given enough knowledge of the influence of different parameters, so that normal sublevel caving can be efficiently planned.

Jan 1, 1975

By Jinrong (Patrick) Zhang

Improvement of conventional flotation efficiency, separation of carbonates from apatite, recovery of phosphate values from phosphatic clay and other ways of utilizing the clay, disposal of clay slurries and subsequent reclamation of the settling areas, and conservation of resources and energy remain major challenges in the beneficiation area for the phosphate industry. These problems have been actively investigated by the industry, government agencies, and research organizations for decades with modest success. However, some recent research activities have generated promising results and possible new technologies. The dominant position of the Crago process in phosphate beneficiation is being challenged by some of the single stage processing schemes. Heavy media separation enables one producer to process a portion of high carbonate ores. Separation of dolomite from apatite by reverse flotation of carbonates with phosphate depressants showed potential for industrial application. Consolidation of phosphatic clays in mine cuts using a modified "sandwich" process is being tested. Beneficiation in the acidulation plant or grinding at the mines may be considered in the future.

Jan 1, 1993

By G. Bhaskar Raju, S. Prabhakar

The amenability of column flotation for the beneficiation of fluorspar was investigated, and the overall performance of the column, flotation was compared to the performance of the existing conventional flotation cells at the plant. It was estab¬lished that improved grades and recoveries could be obtained by adopting column technology. Acidspar concentrates as¬saying 97% CaF2, suitable for HF manufacturing, can be produced by adopting two-stage column cleaning in place of multistage cleaning by conventional cells. Similarly, metspar concentrates assaying 90% CaF2, suitable for metallurgical applications, can be achieved in a single-stage cleaning by column flotation. This is an improvement over what is now being achieved using the existing conventional rougher and three-stage cleaning cells in the plant. The number of stages, i.e.,four in the acidspar circuit and four in the metspar circuit, including rougher stages, can be eliminated by adopting a three-column configuration. Thus, the cost of production, the complexity of the circuit and the power consumption can be effectively reduced with other attendant benefits.

Jan 1, 2000

By J. F. Rakszawski, Robert P. D'Orazio

The use of cyanide in the processing of gold has been documented for over a century. It is still one of the more effective methods of isolating gold, as witnessed by the fact that in 1987 cyanidation was used in the processing of 91.5% of the gold produced in the United States.

Jan 1, 1990

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By D. Krzyszton, P. Czaja

Mining explosions in rocks originate stress waves of great intensity, which crush the surrounding rocks and are then propagated as a seismic wave. Seismic waves are the cause of dynamic loading of pillars and their subsequent destruction. In calculating safe dimensions for inter-room pillars, not only the stresses conditioned by overburden pressures should be taken into consideration, but also the dynamic stresses caused by explosion. This is of particular importance for pillars with great specific acoustic impedance which have been destroyed mainly by the reflected seismic wave. It is possible to take dynamic loading into consideration in the calculation of pillars when the parameters of the propagation wave, the dynamic elastic constants of rocks, the strength properties of rocks, the strength properties of rocks subjected to dynamic loads and the parameters of the blasting charge are known. An example of the calculation for the safe width of an inter-room pillar subjected to the seismic effect of an explosion is given and the possibilities of reducing the dynamic loading of pillars are discussed.

Jan 1, 1982

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994

By J. L. Brinkman

"One of the most common emissions from detonating explosives are nitrogen oxides (NOx), which are potentially deadly if inhaled. Lab studies estimate emission quantities, though great variation is shown based on site-specific conditions, and lab tests may not fully represent field results. Field VALUES (have not been measured due to the vast area affected. OSMRE recently promised to release a ruling regarding surface mine NOx production. Once the ruling is implemented, it may eventually be necessary to monitor site-specific NOx production from blasting. A small unmanned aerial vehicle system (sUAS) is able to carry a NOx gas monitor, rapidly travel to the blast location, and to follow resulting clouds of dust and emission gasses. This project will perform laboratory tests to expand on current estimations, determine an optimal method for collecting data, and evaluate the ability for this unique application of sUAS to assist in health risk assessment for mine employees and nearby communities. Additionally, large initial NOx concentrations do not necessarily correlate to unsafe conditions, and this project will be ground breaking in observance of surface blasting emission dispersion. The project is still in early phases at the time of submission for this paper (Nov 1, 2017). Therefore, this paper focuses primarily on summarizing background research related to the project and a description of the project plan. INTRODUCTION Nitrogen oxide gases (NOx) are common emission by products of surface mine blasting. These gases can potentially cause risk to human health and safety, both for mine workers and communities near the blast site. However, these emission quantities are largely unmeasured and no attempts have been made to relate these VALUES (to human health risk. The primary objectives of this project are to determine actual quantities of emission gases produced during surface blasting, to evaluate immediate and long-term risks to nearby people, communities, and ecosystems, to develop a system for mine employees to easily monitor emission and risk levels, and then provide guidelines for mitigating health risks based on a location’s emission results. BACKGROUND Current research regarding health risk produced by surface mine blasting NOx emissions is extremely lacking. Estimations have been made based on laboratory research, though these same test results show wide ranges of possible gas quantities produced based on site-specific conditions. Even if these estimations are accurate, no method has been created to relate gas quantity produced to human exposure concentrations. To further understand this field, background research was studied pertaining to blasting emission gas formation, laboratory and field measurements, harmful effects of blasting emission gases, and relevant government regulations. Background on Blasting Emission Gases"

Jan 1, 2018

By Michael J. Pratko

The bulk handling industries have long been plagued with problems in their attempt to obtain one of their major goals - the maximum efficiency for which a bulk handling flow system was designed. Mentor Dynamics Ltd. is an international firm with offices in Canada, Japan, and the United States. Mentor Dynamics Ltd. is in the business of solving the "why not" of a system and engineers the solution for the problem. Studies of the varied difficulties encountered with bulk flow systems indicate that 90% of all flow problems fall into one or more of the following categories: abrasion, impact, sticking, and/or inadequate design. These problems can occur with a myriad of bulk solids: coal, gypsum, aragonite, phosphate, fly ash, ore. Solutions to the problems are as varied as the problems. The proper lining material, ceramic, urethane, rubber, and/ or ultra high molecular weight polyethylene, must be coupled with the correct fastening system, annular ring and &apos;F&apos; cap, weld washer, button head fastener, weld studs and/or nuts and bolts.

Jan 1, 1982

By Theodore Balberyszski

The gradual depletion of high-grade sulphide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of non-sulphides possible, although in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulphidize the surface of the relevant oxide mineral and thus make it amenable to flotation. (1) (2) (3) In recent years, Bautista and Sollenberger(4) have investigated the conversion of a number of oxides to sulphides by reacting them with molten sulpur. This paper presents the results of investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulphidized minerals. It is divided into two parts; Part I describes the sulphidization of a number of oxides and a silicate, and Part II presents the flotation behavior of the products of sulphidization.

Jan 1, 1968

By Bobby C. Carson

INTRODUCTION The National Park Service is entering the seventh year of monitoring caves for the presence of radon and radon daughter products. The purpose of this paper is to summarize the radiation monitoring program at Mammoth Cave National Park, and to present some of the results of this program. Mammoth Cave National Park completed five years of collecting data on May 1, 1981: although Mammoth Cave encompasses approximately 361 km of underground passageways, this paper will concentrate on only a 2.2 km section of the cave known as the Historic Tour. Included in this paper is a discussion of the methods the Nations Park Service uses to protect employees from exposure to alpha radiation. MONITORING METHODS The National Park Service monitors cave atmospheres utilizing the procedures provided by the Mine Safety and Health Administration in their Radiation Monitoring Training Manual (Anon., 1976). This procedure is described as the Kusnetz Method (Kusnetz, 1956) of radon daughter monitoring. Due to the length of the tours at Mammoth Cave, it has been determined to be the most practical procedure. The Historic Tour is a 2.2 km (1.4 mile) loop through passageways ranging in size from 18 m high by 12 m wide, to 0.9 m high by 0.6 m wide. Seven five minute walking samples were taken for this cave tour by drawing at least 10 1 of air through a 25 mm fiberglass filter utilizing a Monitaire Sampler Pump. The radon daughter concentration levels were determined using an alpha scintillation counter to measure the alpha activity on the filter paper. The Monitaire Sampler Pump was calibrated each day prior to monitoring the cave tour and the scintillation counter was calibrated by procedures described by the Mine Safety and Health Administration (Beckman, 1975) at six month intervals. Guidelines established by the National Park Service and approved by the Mine Safety and Health Administration require weekly sampling when the average working level exceeds 0.30 (NPS-14, 1980). A working level is an atmospheric concentration of radon (Rn-222) daughters which will deliver 1.3 x 10 5 MeV of alpha energy per liter of air in decaying through Ra C&apos; (Po-214). The Historic Tour has continually exceeded the 0.30 working level average and has been monitored weekly. Generally, only radon daughter working level data has been collected on the Historic Tour due to limited personnel. However, other special measurements of the uncombined fractions of radon daughters with wire screens, tsivoglou method for radon daughter sampling (Thomas modification, 1970), and thoron daughter monitoring. These special measurements have not been routine due to time limitations involved in radon daughter sampling of other occupied portions of the cave. SUMMARY OF DATA The Historic Tour has been the most consistantly monitored tour since elevated levels of alpha radiation were found to exist at Mammoth. Cave. It is also the only natural entrance to the main sections of the cave and provided an opportunity to study man made actions upon the natural entrance. For these reasons the Historic Tour was isolated for study. Beginning October 10, 1977, and ending November 20, 1977, a pilot project was undertaken involving the Historic Tour and the practice of covering the natural entrance to this tour with sheet metal in the winter months. The purpose was to study radiation levels on the Historice Tour while the covers were on and off the natural entrance. In this pilot project, comparisons were made with incast air with covers on and off the entrance, and outcast air with covers on and off the entrance. TABLE 1 Incast air Mean W.L. Covers on . . . . 1.46 W.L. Increased 54% Covers off. . . . 0.67 W.L. when covers on Outcast air Mean W.L. Covers on . . . . 1.33 W.L. Decreased 5% Covers off. . . . 1.40 W.L. when covers on The natural entrance was artificially covered in the winter months (Yarborough, 1978) to protect the visitor from the extremely cold incast air, in the first four years of monitoring. The data in Table 1, illustrated in Figures 1 and 2, shows that this action increased the radon daughter working levels on the Historic Tour by 54% when the covers were on the entrance and the airflow was incast. While the air flow was outcast at the natural entrance, it made little difference as to whether the entrance was closed or open. Some interesting findings were observed when

Jan 1, 1981

By Malcolm T. Wane

The subject matter of this paper, "Applied Rock Mechanics?," has its genesis in a recent field trip taken by the author. A more or less standard question asked at the mines visited was "How are you using the principles of Rock Mechanics to assist you in maintaining an efficient, safe, and competitive mining operation?" The question was couched in a number of different forms, but the intent was to determine whether or not a general theory based on reason and the scientific method was applied or whether the alternatives of tradition, intuition, ?common sense&apos;, revelation, ?shotgun methods&apos; or authoritarianism were invoked. Perhaps two responses to this query will be illustrative of the general nature of the replies. At operation XYZ an extension to the known ore body has been found. The extension is of large enough size and grade that a mining scheme using load-haul-damp techniques is envisaged. Since this represents a departure from the present mining scheme, questions have arisen regarding pillar sizes, room and entry sizes and possible support requirements. A task force has been set up to expeditiously plan for these things and write the necessary specifications and requirements. The fundamental question was posed to members of this group.

Jan 1, 1971

By Patti J. Best

The Southern Powder River Basin (SPRB) now commands 30% of the US utility, coal market due to the region&apos;s low mine production costs, competitive rail rates and low sulfur content. In 1997, production exceeded 240 Mt (265 million st). This was an in¬crease of 104 Mt (115 million st) since 1989 and 4.5 Mt (5 million st) above 1996. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) approaches. This growth will be the greatest in the southern part of the Basin where coal quality is higher. Coal characteristics SPRB coal is classified as subbituminous due to its low heating value and high moisture content. The coal is characterized by low sulfur and ash contents, low ash fusion temperatures and high reactivities. In 1997, the average heating content was 8,593 Btu/lb, with an average sulfur and ash content of 0.79 lbs S02/million [ ] Btu and 5.13%, respectively. The distinguishing characteristic of SPRB coal is its low sulfur content. Most SPRB coal contains less than 1.2 lbs S02/million Btu. This is the approximate definition of "compliance" coal for Phase II of the CA AA. Much of the coal, particularly in the southern part of the Basin, is referred to as "super-compliance" coal due to SO2 contents of between 0.4 and 0.7 lbs SO2/million Btu. The SPRB is divided into three geographic clusters based on coal quality. Mines located in the southern part produce coal with the lowest average sulfur content and highest heating content, almost 400

Jan 1, 1998

By Paul Mitchell, Amy Wheaton, James Rybock

Acid rock drainage (ARD) represents one of the most intractable problems faced by the non-ferrous metal and coal mining sectors, and the creation in the recent past of a number of high-level national and international initiatives reflects the growing concerns of industry, government and other stakeholder groups. ARD is certainly considered one of the most serious environmental impacts caused by mining and the industry's greatest environment-related technical challenge. Additionally, the global depletion of non-acid generating oxide ore deposits and the increasing dominance of sulphide ores means that the potential for ARD incidents will continue to increase. Once initiated, the cycle of chemically and biologically mediated and catalysed reactions leading to ARD generation is difficult to stop. While there is evidence to suggest that the degree of contamination of ARD will decrease rapidly within a relatively short timeframe (Wood et al., 1999), experience in historic mining regions of the world indicates that the problem may persist for centuries at certain sites. Current best practice in dealing with ARD puts the emphasis on prediction and prevention, planned from the outset of the operation and integrated with each phase of the mine site life cycle. The elements that constitute best practice are becoming more clearly defined and as this process of clarification continues industry will undoubtedly accelerate the process of best practice implementation, burying at last the image of mining as a despoiler and polluter of landscapes, an image based on past, rather than current, practices. However, it is equally clear that despite the best efforts of industry and regulators, many sites will continue to generate ARD during operation and following closure - in many cases, a legacy of ARD has been derived from operational and strategic decisions made decades ago, before the risks and impacts of the self-sustaining cycle of ARD generation were properly understood. Add to this ARD generation from poorly managed operations and from historic and abandoned sites, and it becomes clear that the treatment of ARD will be required for the foreseeable future to protect water quality, and ecosystem and human health.

Jan 1, 1999

By Nikhil Dhawan, Shrey Agrawal, Ashwini Kumar

The current study investigates sericite clay as an alternative source of potash and alumina. The alumina and potash content in the sericite is approximately 35 and 10%, respectively, compared with 50–55% in bauxite ore. Muscovite and illite phases are stable, and direct leaching is found to be ineffective. Here, planetary ball milling was performed, which provided dissociation of stable phases to relatively reactive phases. The milling led to a five-fold increase in the surface area, resulting in enhanced leaching kinetics even at low acid concentration. The statistical design obtained optimal conditions of 8 h of milling followed by leaching in 1.73 M HCl at 75 °C, yielding 82% alumina extraction in precipitate with 85% purity in γ-alumina form and 63% potassium dissolution in sylvinite phase. The yield of the precipitate was ~65–68%, and the acid leach residue contained primarily silica.

By G. Gregory Bryan

G. GREGORY BRYAN 33.1-DEFINITIONS 1. Engineering-Engineering may be defined simply as the science and art of making materials and energy serve the purposes of mankind. There are many fields of engineering, each with specialized branches. The basic fields are: civil, mechanical, electrical and chemical. Others may be specialized phases of one of these or a combination of two or more of them. Mining engineering, for example, requires a working knowledge of construction, mechanics, electricity, metallurgy, geology, accounting and economics, in addition to mining techniques or methods. Mining geology and geological engineering involve rocks and their structure and the forces that act upon them, and chemistry, physics and mechanics also are important to practitioners in these fields. Metallurgical engineering requires chemistry and physics but also a working knowledge of mechanics and electricity. The fields of engineering with which this section are concerned are those primarily involved in the finding, mining, processing and utilization of the natural mineral resources of the earth. They include geology, mining engineering and metallurgy, each with several specialized subdivisions. 2. The Engineer-The engineer is an individual who has had specialized training to qualify him to practice the profession of engineering. The term engineer is used here in its broadest sense to include such professions as certain applied branches of geology, physics and chemistry, whose practitioners may not have acquired engineering degrees but who, nevertheless, by training and experience in some area of the minerals industry, qualify under the above definition. To become a successful engineer, a person should have certain pronounced aptitudes and preferences, even before embarking upon the requisite course of training. Among the chief qualifications that the engineer-to-he must possess are: (a) a natural inclination toward mathematics and the physical sciences, and (b) intellectual and moral honesty. Among the qualities the student engineer must develop are: (a) independence of thought, open-mindedness, sound judgment and the ability to observe, deduce, plan and apply solutions, (b) the ability to articulate and convince, and (c) the ability to organize and direct the activity of others. These qualities are normally developed through sound education, followed by pro¬gressive experience. 3. The Consulting Engineer-The consulting engineer is an engineer primarily in the business of furnishing specialized advice and engineering services on an intermit¬tent, part-time or occasional basis to clients who do not have continuous or full-time need for those services. He must be able to make and take full responsibility for decisions and recom¬mendations where original thought is required. He should not be confused with the engineer, surveyor or technician who also may furnish services on an intermittent basis, such as regular periodic surveys, the overseeing of drilling programs and other such routine work as may require little original thought and planning. 33.2-THE PROFESSION OF CONSULTING ENGINEERING 33.2.1- QUALITIES REQUIRED A successful consulting engineer must first have, as a minimum, the qualities and preparation of an engineer. In addition, he must have sufficient knowledge,

Jan 1, 1973