Search Documents

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By Richard Keith Corbin

INTRODUCTION With the world media full of predictions that the price of gold will quadruple in three years (Maybury, R.J., 1988), and with financial forecasters and strategists touting opportunities to make 400% in gold (Skousen, M., 1988), explorationists and entrepreneurs are scurrying to find enough gold to feed the global gold fever created. At the same time, gold deposits in the United States and other developed and intermediate countries are becoming less attractive because of environmental restrictions, radical reductions in tax incentives, and depleting reserves, causing people in the mining industry to begin looking at opportunities for foreign investment in gold mining concessions in lesser developed countries (LDCs). Meanwhile, LDCs are responding with chamber-of-commerce aplomb in marketing their opportunities. In the face of all this frenzy and hype, targeting gold mining concessions in LDCs for foreign investment may be done more objectively by employing a systematic approach. For this paper the SHOP rating system (Corbin, R.K., 1987), which considers factors of the LDC's stability, hospitability, ore occurrence, and profitability potential is used. The result is that a tiny banana-growing republic in Central America, first discovered by Columbus and named the "Rich Coast'' because of the many gold adornments worn by its Indians, has been rediscovered and emerges as a classic LDC gold target.

Jan 1, 1988

By G. T. Adel

Hindered-bed separators are often used in the minerals processing industry to classify particles according to size and density. A new technology, known as the Eriez CrossFlow, was recently developed to overcome some of the limitations associated with hydraulic separators. The innovative feature of this unit is a novel feed presentation system that improves separation efficiency and capacity. In the present work, a detailed process engineering evaluation was conducted to determine the basis for the improved performance of this unit. The evaluation included controlled separation tests using well-characterized feeds, particle and liquid tracer experiments and mathematical modeling studies. Data obtained from this work show that the new separator is capable of maintaining good separation efficiencies at higher solid feed rates than traditional designs due to improved hydrodynamics in the separation zone. This paper reviews the operating principle of the Eriez CrossFlow separator, discusses the results of the tracer experiments and modeling studies and presents test data obtained from recent laboratory and plant trials. Key words: Size classification, CrossFlow separator, Hindered-bed separator, Hydraulic separator

Jan 1, 2003

By N. B. Aughenbaugh

Compacted, fine-grained soils, often referred to collectively as clays, are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials for these liners include a variety of sand, silt and clay admixtures. These exhibit dramatically different engineering properties when densified. Therefore, it is imperative to adequately assess and characterize any soils being considered for compacted liners. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Because they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners also must include an evaluation of their flexibility. That is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1991

By V. N. Kelly

The ability to link geological sections on a graphics screen to form three dimensional geology representation was implemented at Kidd Creek in 1987. This technique affords an opportunity to optimize metal estimation in ore at the Kidd Creek copper, zinc and silver mine, by applying enhanced interpretation methods. On a series of geological sections varieties of ore are outlined. These are linked from section to section to form polyhedra which closely simulate the three dimensional shapes of the different ore types referred to as mintypes. The orebodies are divided into zones, referred to as domains, that approximate the function of variograrns, for which' preferential continuity of mineralization has been estimated for distances in the width, strike and dip directions. These distances define ellipsoidal volumes of influence. The domains are also linked into polyhedra. Both types, coded by ore variety and zone, are mapped into the block model. Tonnage and metal values are calculated for ten-foot cubical cells of the block model by any of several estimation methods under domain control. In estimating the metal grades for a cell the predetermined search ellipse is applied to select only those drill hole assays of the same mintype as the cell designation. Once grade estimations have been determined for the cubical cells comprising the model, a wide range of stored information can be viewed. For example, in plan at any row elevation or on vertical section at any azimuth, as either printed values for the cells or as contoured data. This flexibility is of particular value in checking and refining the geological interpretation to better conform to ore types and grades actually mined. Combined with three dimensional geological modelling, and correctly chosen domains, the use of mintypes implants essential geological control into the system and prevents assays for one ore type from affecting grade estimation in adjacent ore types. The three dimensional geological modelling and block model segments provide information which is effectively applied to the stope design, production, planning and control parts of the system.

Jan 1, 1989

By E. J. Beckman, R. M. Enick, C. Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic platinum group metal complexes from an aqueous phase. However, because conventional extractant-metal complexes are not soluble in liquid carbon dioxide, this can be achieved only if highly carbon dioxide-soluble extractants are developed. For example, trioctylamine-gold chloride is not soluble in liquid carbon dioxide, although trioctylamine is CO2 soluble. The novel CO2-soluble extractants presented in this paper have a CO2-philic fluorinated tail to enhance solubility and a conventional amine head group for extraction of metals. Both the extractant and the extractant-metal complex are soluble at ambient temperature at pressures from 7 to 35 MPa. Efficiency factors as high as 2.23 have been measured using 1,1,2-trichlorotrifluoroethane (TCTFE), a low pressure screening liquid for carbon dioxide, indicating that these compounds will strongly bind the metal chloride. For example, 84% of Pt-chloride was extracted into TCTFE using a 3.5:1 ratio of a double¬tailed fluoroalkyl amine extractant: metal chloride. An 88% recovery of Pt-chloride into high-pressure liquid carbon dioxide was achieved using the same extractant at a 3.5:1 ratio. Therefore, it appears possible to replace organic solvents with liquid carbon dioxide during the extraction of platinum chlorides if highly carbon dioxide-soluble extractants agents are employed.

Jan 1, 2002

By F. D. Wicks

This paper summarizes the direct operating cash costs for the Barrick Mercur open pit gold mine. A comprehensive, detailed system of cost management has been in effect for the life of the Mercur operation. This system provides the basic data for operations control and is the basis for drafting budgets as well as analyzing impact of change on operations costs. The ore body is complex geologically and metallurgically, requiring operators to pay close attention to mining and processing costs. The cost history provides data which enables analysis of changes in production levels, aging of the mine production fleet, and the impact of specific cost changes through time.

Jan 1, 1993

By Norman L. Weiss

The full importance of tailings disposal is yet to be realized by the mining industry, but our awareness of its present and future implications is growing faster, perhaps, than any single phase of ore processing. Few engineers can look very far into the future because of the complexity of the problems that may confront us if we project from the general indifference of past years through what we are already being expected to correct in existing operations, to confrontations with new statutes and an awakened public in any new plants hence- forth. The mistakes of the past have not been limited to the United States nor even to other countries of the Western Hemisphere. Indeed, all continents and subcontinents have suffered from myopia in releasing the tailings without retaining responsibility. However, the US as one of the world's great leaders in technology has a particularly unimpressive record. It may be safely generalized that the degree of control applied to the tailings of a milling operation has depended upon several factors more important than national boundaries. Thus in arid and semiarid climates no incentive was needed other than the scarcity of water to create a permanent and stable lodgment for mill tailings. On the other hand. where water has been plentiful. the temptation to let the tailings run into a river or lake or ocean (at least at certain times of the year) was often irresistible. So we find that modem tailings disposal in the southwest deserts of this country, with one or two notable exceptions where very serious breaks seem to occur at regular intervals, is satisfactory according to the standards of the 195QF and 1960s. while in various operations in Idaho, Michigan, western Colorado. Newfoundland, and elsewhere the record has been less praiseworthy. In the same way, cyanide plants which did not concern themselves about leakage, seepage, spillage, or wastage of tailings pulps with solutions containing toxic levels of free or combined cyanide soon heard a demand for better control. In consequence the industry has seen a growing use of cyanide regeneration of tailings or wash solutions, elimination of leakage, and careful structuring of tailing dams. The chemical and thermal qualities of tailing waters have occasionally been a spur to good tailings management. Some tailings disposal problems for example, the southeastern Florida phosphate clays and the Bayer red muds-have been given the intensive study they merited, but not always with much success.

Jan 1, 1985

By Klaus Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300 and 600 °C is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies depending upon structural homogeneity, porosity and gangue quantity. Especially sinters with heterogeneous structures transmit stress to the hematite phase and this favours disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1981

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to--float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in processing porphyry ores and treatment methods to overcome them. Though some of the problems are interrelated, they are classified into three broad categories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment, and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1987

By Ian Sheppard, John J. Chen

This paper describes the development of the underground mining methods employed for narrow silver-lead-zinc orebodies at the Isa Lead Mine. Cut-and-fill methods were the chief underground mining methods for the narrow orebodies at the mine over 35 years ago. Benching methods were introduced approximately two decades later, and quickly replacing the cut-and-fill methods. The cut-and-fill methods and the benching methods are briefly reviewed in the paper. The benching methods and technologies have been continually evolving and one of the recent achievements is a multi-lift benching method. The multi-lift benching method is described in detail.

Jan 1, 2001

By Donald G. Dahle

Project Payette is a conceptual nuclear experiment under the Vela Uniform program intended to further evaluate the mechanism of seismic decoupling. Vela Uniform is a Department of Defense program to improve this country's capability to detect, locate and identify underground nuclear detonations. This program evolved from recommendations of the Panel on Seismic Improve¬ment, (Berkner Panel), an officially appointed group of noted U. S. scientists. This Panel, taking note of difficulties in detecting the differences between some underground nuclear detonations and some earthquakes recommended a program of increased basic research in seismology. The theory of decoupling, Which involves possible reducing of seismic motion resulting from underground explosions by reducing the coupling or physical linkage between the explosion and the geologic environment, was investigated by Dr. Albert latter and his associates at RAND during the late 1950's. The concept has been further investigated theoretically by scientists of the Lawrence Radiation Laboratory and the Sandia Laboratory. The theory has been tested experimentally under Vela Uniform Projects Cowboy, Dribble and Sterling. The Salmon Event of Project Dribble was a tamped (with the explosive in firm contact with the geologic formation) nuclear detonation 2700 feet below ground in the Tatum Salt Dome. Project Payette, if found to be feasible and if authorized for actual execution, would become a decoupled experiment in the same environment.

Jan 1, 1968

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, gold-silver deposit. Current proven and probable reserves are 8.9 Mt (9.8 million st) grading 1.5 g/t (0.044 oz/ st) gold, minable by open pit and amenable to heap leaching. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold at Santa Rosa occurs principally as electrum, finely disseminated through intermediate tuffs, and associated with pyrite. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1995

By E. P. Chen

This investigation involves the development of a two-dimensional continuum model for the description of jointed media. Specific application of the model developed here is for the potential geological disposal of radioactive waste in the layered sequence of fractured volcanic tuffs under Yucca Mountain, Nevada. This is currently being considered by the Nevada Nuclear Waste Storage Investigations Project, administered by the Nevada Operations Office of the U. S. Department of Energy. The work is a direct extension of the previous constitutive model by Thomas (1982) based on the work of Morland (1974). The main feature of Thomas's model includes two parts: a continuum approximation based on average discontinuous displacements across jointing planes within a representative elementary volume, and a material constitutive description based on linear elastic matrix material behavior and nonlinear normal and shear joint behavior between jointing planes. The mathematical descriptions by Morland based on strain partitioning among matrix material and joint sets allow multiple joint sets to be included in the model. However, the initial effort by Thomas to implement Morland's mathematical model included only a single set of joints. To make the material model reflect more realistically the field characteristics, the current work extended Thomas's model to include orthogonal sets of joints. The nonlinear elastic normal joint behavior is retained in the present model. Joint shear response was treated as linear elastic in the shear stress versus shear displacement relationship prior to attaining the stress level governed by the Coulomb friction criterion. Beyond this critical stress value, a horizontal line is assumed in the work of Thomas for the shear stress versus slip displacement relationship such that the shear stress remains constant while the slip displacement increases. Motivated by experimental observation, the current work generalized the shear response to allow a line with finite slope to govern the slip behavior beyond the critical stress level. The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Formulation of the Continuum Model The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Let us focus our attention on the set with normal n first. Let the jump dilation displacement and jump slip dasplacement associated with the [ ]

Jan 1, 1986

By H. C. Siebert

According to the "Survey of Energy Resources 1980" (1)*, which was prepared by the Federal Institute for Geosciences and Raw Materials in Hannover (FRG)for the World Energy Conference 1980 in Munich, the world coal deposits are assessed at 775 billion tce proven reserves 448 billion tce of them recoverable and 6 161 billion tce additional resources. If one ignores growth rates, the current world coal output of 2,8 billion tpy gives our recoverable reserves a static life expectancy of 175 years. With an average increase in world output of 3,2 % like between 1973 and 1980 this range would be further shortened to an alarming degree. Furthermore, the criteria used to distinguish between workable and unworkable resources give rise to the suspicion that deposit characteristics are not always taken into account to a sufficient degree. For example, little attention is paid to major ?Bonitaet" - factors such as dip and seam thickness. There have been wide-ranging scientific discussions on the lower limit for workable coal resources, but no such limits have been set at the other end of the scale. Otherwise it is well known that performance and costs are badly affected den in level and moderately inclined seams the seam thickness is more than 4 to 5 m, because special mining methods have to be used beyond this limit. These are associated with significantly higher costs than with the winning of seams of ?normal? thickness.

Jan 1, 1985

By S. Ash

Murray mine was one of the first Mechanized cut and fill underground gold operations in Northern Nevada. At the end of 2002 mine production began to decline and Murray entered a phase of remnant mining and began preparations to close down. The remaining mining took place along the ore waste boundary, in previously condemned areas, and in highly challenging ground conditions. To remain economically viable new techniques were implemented in operations, geology, engineering, and rock mechanics. These improvements pushed the edge of known and accepted mining practices and have allowed Murray to remain in operation today. History The Murray mine is located on the Jerritt Canyon property, which is located 45 miles north of Elko, NV in the Independence mountain range. Mining operations started at Jerritt Canyon in 1980 out of several open pits. In 1993 underground mining began in conjunction with a decline of surface mining operations. The transition from surface mining to underground mining moved the property into a new era. At the time there were limited examples of successful underground operations in the area from which to draw experience. Several mining methods were attempted with varying degrees of success and underhand cut and fill proved to be the most effective method. To date Murray has mined 1.2 million ounces at an average grade of .335 OPT utilizing this mining method.

Jan 1, 2006

By Robert L. Virta

An asbestos substitute is any material that replaces asbestos in a commercial product. There are many asbestos substitutes, each with its own unique physical and chemical properties. Substitutes can be inorganic or organic, fibrous or nonfibrous, and natural or synthetic. They also can be used as a direct substitute for asbestos or as a replacement product. Probably in no other field is the diversity of substitute materials so great. The concept of asbestos substitutes is not new. The first major effort to develop asbestos substitutes was undertaken by the federal government. The United States has always been dependent on foreign sources for strategic-grade asbestos, and during World War II, the government was concerned that these supplies would be cut off. Strategic-grade asbestos was critical in many electrical and thermal insulation applications (electrical insulation, battery plate separators, flame-proof boards, insulation for rocket components, etc.). A reliable supply of nonstrategic-grade asbestos also was required for general civilian and military applications, such as in brakes, clutches, and construction materials. The government not only initiated a major search for deposits containing strategic-grade asbestos, it also funded research on synthesizing asbestos in the laboratory and developing products that did not contain strategic- grade asbestos. These efforts, as well as those conducted by the private sector, generally were unsuccessful. In the late 1960s and early 1970s, a second major effort to develop asbestos substitutes began because the general public was concerned about the health threat posed by the release of asbestos fibers during the manufacture, use, repair, and disposal of asbestos-containing products. Strict regulations covering the mining and manufacturing sector already had been enacted because of the issue of occupational exposure. The issue then became environmental exposures. Environmental regulations were enacted, and through time they became more strict. The combination of increasingly strict environmental regulation, maturing of some asbestos markets, and liability issues prompted many manufacturers to discontinue asbestos product lines or search for asbestos substitutes. As a result, asbestos usage dramatically declined from the 1970s to the present (Table 1).

Jan 1, 1994

By J. Hoover

Real growth in the economy, increasing demand for electricity, and consumer stockpiling for a possible United Mineworkers of America (UMW) strike in October made 1984 a banner year for coal. Production and consumption climbed to record heights. Precautionary purchases brought inventories close to the peak levels of early 1981 when coal miners walked out for 72 days. Production slowed in the fourth quarter after labor and management concluded negotiations without a walkout. But output in every major coal producing state showed significant gains during the year US coal production totaled 807 Mt (890 million st) in 1984. This is a 13.8% increase over 1983 output. Lower production rates, principally in Appalachia, and sustained demand in the final quarter put downward pressure on coal stocks by the end of the year. Demand All market sectors experienced greater requirements for coal in 1984. Electric utility coal consumption increased 6.3%; exports climbed 4.8%; coke plants consumed 18.9% more coal; coal requirements in the other industrial sector expanded by 11.8%; and consumption in the residential/commercial sector rose 8.1%. Domestic consumption of coal reached a record 718 Mt (791 million st) in 1984. This is a 7.4% gain over the previous consumption high of 668 Mt (737 million st) in 1983. Electric Utilities The 4.6% increase in electric power generation in 1984 was coupled with expanding coal use relative to other energy sources. This resulted in a 6.3% rise in coal consumption, totaling 603 Mt (664 million st) for the year. Thirty-eight of 45 states where coal-fired electric power plants were operating shared in the 36-Mt (39 million-st) increase in electric utility coal consumption

Jan 5, 1985

By Keith G. Wallace, Justus B. Deen, Daniel J. Brunner

This paper describes the impact of natural ventilation pressure (NVP) on the Nuclear Waste Isolation Pilot Plant in New Mexico (WIPP). The WIPP site is a U.S. Department of Energy underground facility for the disposal of low level radioactive transuranic defense generated waste. Because the facility is designed for the storage of nuclear waste, special design considerations are necessary to ensure containment of potential radioactive releases. The main design considerations which influence the ventilation system are the requirements of separate air splits for mining and storage operations and of air filtering before atmospheric discharge in the event of a radioactive release. The leakage between the two air splits must always be from the mining area to the storage area. The transient effects of natural ventilation pressures, caused by seasonal and diurnal surface temperature changes, impact the ventilation characteristics throughout the facility. This paper discusses the measurements taken to quantify the changes in NVP and the engineered systems designed to mitigate against the effects of NVP.

Jan 1, 1991

By Charles D. Litton, Ronald S. Conti

This report describes the results of research conducted in the Bureau of Mines Experimental Mine at Lake Lynn Laboratory to determine the effects of air velocity, sensor spacing, and stratification of CO levels on the detection of slowly-developing coal/conveyor belt fires. In general, the time to detect a developing fire is calculated assuming an average CO level that has mixed completely with the ventilated airflow. The data indicate that CO sensors placed near the roof of an entry take advantage of buoyant- induced stratification of combustion products, resulting in earlier detection of developing fires. Even during the low-temperature, smoldering stage of a fire, the combustion products will tend to stratify near the roof, and once flaming occurs, the degree of stratification increases markedly. As one would expect, at higher air velocities, the degree of stratification is less than at lower air velocities, although still significant, especially during the flaming stages of the fire

Jan 1, 1993