Search Documents

By Dave Watson

Henderson Mine personnel have more than 20 years experience and have placed more than 400,000 m3 (520,000 cu yd) of shotcrete and concrete. Over the last 20 years, the mine has used a variety of equipment to place concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Recently, the mine received a state-of-the-art wet shotcrete placer. The batch plant was automated, and a mobile concrete-form jumbo was fabricated. The mine will also receive a new concrete transport truck. Henderson’s background The Henderson Mine is owned by Climax Molybdenum Co., a unit of Amax, Inc. It is an underground, primary molybdenum producer near Empire, CO. The mill is located between Silverthome and Kremmling, CO and is connected to the mine by 16 km (10 miles) of underground and 8 km (5 miles) of surface track. Except for the ore haulage system which is powered by overhead trolley, all mobile equipment is rubber-tired and diesel-powered.

Jan 1, 1992

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By F. L. Wilke

In the german hard-coal mining industry the mechanization of longwall faces and the machinery used for the extraction process have reached such an extent, that an extensive increase in productivity and face performance is not likely to be expected. At present, the greatest amount of man-shifts is needed for operations such as tunneling, transportation and haulage (fig. 1.). The most restrictive parameter, especially considering the possible ad- [ ] vance rate of faces, is the comparatively low advance rate achieved in drifting operations. Therefore improvements in productivity and advance rates of drifting operations will have considerable influence onto the extraction rate of the faces. The importance of drifting operations - and especially the so-called "conventional drifting by drilling and blasting" within the scope of long- term planning strategy of the german hard-coal mining industry is reflected by the development factor. This factor is given by the ratio: cubic meters of rock excavated in drifting per 1.000 tons saleable coal produced. In 1973, which is considered to be the beginning of the oil-crisis, this factor was determined to be 17.7 m3/ 1.000 tons sale- able coal.

Jan 1, 1982

By Ezra L. Kotzin

Foundry sands used to make molds and cores have been very important to foundrymen since metal casting began hundreds of years ago. They are now used in two basic ways, either in an uncured green state, grain-bonded with clay, or in a set cured state achieved with sand that, mixed with resins or oils, is cured by baking or by chemical reaction. The term sand, as generally used in foundry applications, may best be defined as material composed of granular particles of mineral matter, ranging in size from 0.5 to 2 mm in diameter. The particulate nature of the material may be the result of natural disaggregation or result from crushing and screening of rock or ceramic materials; crushed and screened products are sometimes referred to as "manufactured sand." Based on their origin, the raw materials for foundry sands will vary in grain shape, grain composition, relative surface, grain size, and grain distribution patterns. These properties, in addition to their chemical analyses, sintering point and expansion characteristics play an important part in the choice of sands used as the base molding or core aggregate in metal casting. Sands with different origins may be blended to produce specific compositions and grain size distributions. Early raw material requirements based on silica sand were simple, but as sand/core/mold technology became more sophisticated and binder technology continued to be developed, the physical properties of foundry sands became more critical. Silica sand is composed of quartz, along with, in most cases, small amounts of feldspar, mica, clay, and other common minerals. Although silica sand is still by far the most widely used base material in production of molds and cores used in metal casting, other natural mineral sands have their own unique characteristics and fill an important niche in special applications. As a result, the term sand, as applied to raw materials used in metal casting, has been logically extended to include granular materials composed of a group of minerals other than quartz. With increased use in advanced foundry technology, natural sands composed predominantly of zircon, chromite, staurolite, or aluminum silicate minerals and of granularized chromite or olivine, have become more than just alternate materials and are now commonly classified as sands when the grains are sand-sized. Foundry sand may therefore be considered under two categories: silica sands and non-silica sands.

Jan 1, 1994

By Mark E. Gershon

Conventional methods of drillhole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drillholes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drillholes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1983

By Gordon E. Ager

A technique for the synthesis of mineral processing flowsheets from laboratory batch test data is described and examples of the application of the procedure are given. The procedure requires the collection of kinetic data, the optimization of the flotation time in each separation stage, then simulation of the material balance for a continuous circuit.

Jan 1, 1989

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercaptosilanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1992

By Peter C. Lighthal, Harvey N. McLeod, Iain G. Bruce

This paper describes the practical aspects of handling cyanide leach tailings. Alternative systems for cyanide destruction are briefly discussed. The provision of adequate retention time to allow natural degradation of cyanide during summer months is the most economical method of cyanide destruction. Cyanide in ground- water can frequently be both persistent and mobile, so that tailings basins should be designed to limit seepage. Common methods for limiting seepage are presented. Other aspects addressed are water balance, winter operation and abandonment of cyanide tailings systems. A case example of the Cheni Gold Mines Lawyers Creek Project tailings handling system is presented.

Jan 1, 1987

By R. L. Loofbourow, Robert R. Miller

Deep, stable, unlined space promises secure, efficient, acceptable solutions to several current problems. With truly favorable conditions, it can be economic as well. The basic requirement is sufficient sound, tight rock at required depth. This and unusual surface requirements point to special testing. An objective is to describe conditions for planners, estimators and contracts. A first stage concept study needn't be prolonged but should overlook nothing significant. Although observations and tests on core are considered essential, time and expense can be cut by supplementing then with tests on walls of rotary or percussion holes. In some places initial drilling could be shallow.

Jan 1, 1981

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By Subhash Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico. is a research and development project sponsored by the U.S. Department of Energy, designed to demonstrate the safe disposal of radioactive waste. A mine (repository) is being developed 2150 feet below the surface in a thick salt bed, which will serve as the disposal medium. The underground ventilation system for the WIPP project was originally designed based on a fixed project scope. The design criteria and ventilation requirements were developed for the performance of various activities as then envisioned towards the achievement of this goal. However, in light of new information and actual site-specific experience at WIPP leading to a clearer definition of the scope-related programs and activities, it was realized that the existing ventilation system may need to be modified. A re-assessment of the ventilation requirements--based on the current status of the facility and a clearer definition of the scope of the experimental programs, waste storage methodology, mine developmental activities. and current equipment list--indicates a two- fold increase in underground airflows from 210,000 cubic feet per minute (cfm) to 425,000 cfm. Various options to provide the increased airflow to the underground facility were considered and analyzed. Based on the techno-economic analysis, safety and environ- mental considerations, and other conditions unique to a facility like WIPP, it was decided to construct a new shaft to serve as the primary fresh air intake, along with the installation of additional fans in parallel with the existing set up. Low cost and the ease with which the new design could be implemented and integrated into the existing ventilation system with minimum impact on current activities and projected schedules were the guiding factors in designing the shaft and related ventilation modifications.

Jan 1, 1987

By S. Yap, F. J. Sotillo, L. P. Irwin, F. M. Utsey

Slimes, especially clays, are detrimental to several processes in the Mining Industry. The efficiency of classification, clarification, gravity separation, and flotation decreases significantly in the presence of slimes and clays. This problem is particularly critical in the Phosphate and Sulfide Industries. To reduce the effect of slimes in mineral processing, several desliming techniques and chemical additives are used, such as sodium silicate, sodium carbonate, sulfuric acid, tripolyphosphate, hexameta phosphate, etc. Lately, the Mining Chemical industry has shift to more “Specifically Developed” reagents that offer the most efficient and cost effective performance, mainly using organic polymers. For this purpose, the Mining Chemical Industry needs to understand the crystal chemistry of minerals, the chemistry of the aqueous media, the interactions in solids-aqueous-gas interfaces, the rheology of the system, and the plant operation conditions and parameters. This paper describes the use of surface chemistry fundamentals on the design of an organic polymer capable of modifying the rheology of clayish slurries of a phosphate ore. The change in the rheological characteristics of the clayish phosphate slurries allow fine ore particles to settle faster by reducing the slurry viscosity. Thus, abetter separation of the ore from the slimes is possible using gravitational or centrifugal forces. As examples of the application of this reagent, industrial and pilot plant tests on desliming using tanks and hydrocyclones are presented. These tests showed the reduction of 32%-36% in ore losses for different phosphate ores during desliming operations, and the increase of cyclones desliming efficiency to 80%. Tests were also carried out to improve the rejection of unwanted iron bearing slimes in phosphate feed. These tests demonstrated that it is possible to reduce by 0.25%-1.23% Fe2O3content in the flotation feed product. As a result, significant economical benefits are observed with the use of this new technology without any adverse effect on down stream operations, such as clay settling or phosphate flotation.

Jan 1, 2003

By Richard B. Jacob

The High Gradient Magnetic Separator (HGMS), also known as the High Gradient Magnetic Filter (HGMF), is an effective device utilized in magnetic separation. This method of separation is gaining popularity in the separation of sub-micron material containing feebly magnetics. The most common use of this type of separator is in the removal of iron stained particles to improve the brightness of kaolin clay. Potential areas for use of this magnet include: (1) desulfurization of coal (2) the clean-up of mill effluent (3) removal of fine particulate matter from municipal and industrial waste (4) desulfurization of oil

Jan 1, 1983

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By Bianca Cruz, Tom Lankiewicz, Kent Sorenson, Karrie Radloff, Elizabeth Deyett, Dayal Saran, Michaeline Albright, Dan Stigers

Biology opens a new frontier for the mining industry. With rising environmental concerns, the need to couple conventional chemical and physical technologies with sustainable approaches is pressing. At Allonnia, we harness microbial processes to create innovative and environmentally responsible technologies with broad applications. The native microbial community (microbiome) remains largely unexplored at most mining sites, unlike the geochemical environment. The exploration of complex biological reactions that could transform mining technology is just starting and holds vast possibilities, spanning bio-cementation, carbon sequestration, ore beneficiation, water mitigation, bioleaching, metals recovery, and more. Allonnia has collected samples from mine sites in Australia, Africa, and North America to characterize the microbiome and uncover the genetic potential present in mineral-rich environments. We are evaluating microbial metabolites that selectively solubilize gangue from various ores. In addition, biological reactions hold promise as tailings stabilizers. Our early efforts illustrate exciting prospects for harnessing biology’s potential in mining.

Feb 1, 2024

By Pan Gao, Songyang Yin, Zhibiao Guo, Jinglin You, Yuhui Li

Under the geological conditions of the interaction of upper goafs and lower working face in deep mining, coal seam mining causes a large stress concentration, which may lead to large deformation of the surrounding rock and rock burst risk. The research reported herein is aimed to utilize the FLAC3D software to establish a three-dimensional numerical model and analyze the law of the surrounding rock stress evolution during coal mining under complex geological conditions. The simulation results reveal that the peak abutment stress reaches its maximum value at 20–30 m in front of the working face, about 1.8–4.3 times the original rock stress, and the peak stress is larger in the stable mining stage. Along the dip of the working face, the peak stress occurs about 8–10 m away from the roadway side. The upper barrier coal pillar and the interval coal pillar in order exhibit stress concentration areas of 142 m and 88 m. According to the law of the deflection stress distribution of the surrounding rock in the presence of various widths of the coal pillar, a 10-m coal pillar between the roadway and the adjacent goaf could enhance the stability of the roadway. For the stress concentration area, drilling holes with a depth of 20–25 m are utilized to reduce the pressure, and anti-impact supports are installed in the middle of the roadway. Due to the varying stresses of the rocks around the roadway, partition prevention and control countermeasures are capable of efficiently preventing the instability of the surrounding rock.

Mar 22, 2023

By Wm. J. McCracken

HISTORICAL REVIEW OF BOARD OPERATIONS The Ontario Worker's Compensation Board was established in law enacted by the legislature of the Province of Ontario in 1915. It was designed to pay insurance benefits to injured workers, and at the same time to protect employers from legal suit. It was based upon an enquiry system rather than an adversary system such as that used in the courts process. Initially, the system was designed to pay compensation benefits and subsequently, to pay for the cost of medical treatment and pensions for disability and disease resultant from the effects of traumatic injury. In 1947, the Act was changed to include industrial or occupational generated diseases, not specifically related to traumatology. Such occupational diseases were therefore accepted and benefits paid subsequent to that date. As will be discussed in several minutes, even today the vast preponderance of compensation claims with the Ontario Board continues to be related to the effects of trauma. HISTORICAL REVIEW OF EXPOSURE TO RADON GAS DECAY PRODUCTS In some areas of Ontario, especially in Northern Ontario, there is a natural leaching of radon gas from the underlying rock formation. This constitutes very low levels of radon gas decay product radiation exposure to those persons coming in contact and inhaling these substances. This paper however is designed to discuss the occupational generated types of radon gas exposures. For many years dating back to the 1930's, partially refined ores were being shipped from Northern Canada to a refinery located at Port Hope, Ontario, still in operation and currently operated by Eldorado Nuclear Limited of Canada. Initially, the purpose for the operation was extraction of radium to be sold on world markets for medical treatment purposes. With the advent of World War II, this market collapsed. Subsequent to World War II, the availability of other sources of radiation for medical radio-therapy generally replaced the requirements for radium. During World War II, a new market opened up for the Port Hope refinery however as work into nuclear chain reactions and the development of the atomic bomb identified the need for uranium and enriched uranium. During the period of operations where radium was being extracted at the Port Hope refinery, it is now known that an identifiable radon gas hazard did exist. This hazard disappeared when the production line for extraction of radium ceased operations. In 1954, uranium mining operations opened up in Ontario at two locations, Bancroft and Elliot Lake. At the peak of operations, 16 mines were operational and 11,000 workers were employed in these mining operations. A high level of mining activity continued over a 10 year interval with the Bancroft Mines closing permanently in 1964 following a 10 year life of operation. The other mines in Elliot Lake closed about the same time with the exception of two uranium mine operations which have continued to be operational up to the present time. By 1965, due to a dramatic drop in world demand for uranium, the total work force had fallen to 1/10 of the peak work force, and approximately 1,300 workers remained in employment. It is of interest to note that one significant difference in the work environment between Elliot Lake and Bancroft was the high silica content of the Elliot Lake ore. This gave rise to a number of cases of silicosis developing in relatively short intervals of time in the Elliot Lake miner population. No cases of silicosis were identified from the Bancroft operations. Based upon the experience in investigating and evaluating actual cases of lung cancer in the uranium miners over the years, the medical staff at the Ontario Board also developed the impression that radiation levels were much higher in the Bancroft operations, especially in the earlier years of operation, than at Elliot Lake. This resulted in accumulation of higher levels of Working Level Months (WLM), usually over a shorter exposure interval in many of the cases. This aspect will be further evaluated in this presentation. Subsequent to 1965, the work force remained quite static in numbers until 1975. At that time, there began to develop an increase in the work force, and this increase is continuing at a moderate rate up to the present. INITIAL METHOD OF HANDLING LUNG CANCER CLAIMS The first lung cancer claims in Ontario from uranium mining operations were accepted on the perceived cause-effect relationship. This relationship was based upon the data from the Colorado observations and the Czechoslovakia data. Initially, a series of regression equations on mortality were developed and used to estimate the effect of exposure to low cumulative doses of radon daughters as it might relate to the frequency of occurrence of lung cancer at any particular cumulative exposure level. A probability of cancer being radiation induced as against it being caused from other factors was calculated. This method was discontinued subsequent to 1972 due to problems encountered in carrying out this complex evaluation. Thereafter, each case was dealt with on an individual basis, being based upon whether or not the tumour was of the oat cell type, a cumulative exposure in excess of 120 WLM; latency periods in excess of 10 years, commencement of mining prior to

Jan 1, 1981

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables.

Jan 1, 1981

By G. H. Schnakenberg Jr.

In response to the underground mining industry's growing concern with the exposure of workers to the diesel particulate matter (DPM) component of diesel exhaust, a method was developed to estimate the average workplace concentration of DPM that could be expected from using the new lower DPMemitting engines now being approved by the US Mine Safety and Health Administration (MSHA) when these new engines are equipped with state-of-the-art exhaustcontrol technology for filtering and combusting DPM. The resulting estimate uses the MSHA-reported particulate index for these engines, the prevailing rule-of-thumb ventilation rate of 150 cfm/hp and the available diesel-exhaust filter technology that has been shown to be at least 80% effective in reducing tailpipe DPM. In the estimate calculation, every engine used in an underground mine is assumed to be equipped with this control technology. Under the stated reasonable conditions, an average DPM level of 90 µg/m3 (mass) is predicted as technically feasible.

Jan 1, 2002

By J. Rostami, J. Brune, S. Slouka

Respirable dust poses long-term health issues to personnel working in mining and civil projects where mechanized mining and tunneling machines are used for hard rock excavation. Machines, such as longwall shearers, roadheaders, or continuous miners, use consumable picks to cut rock. However, rock dust is generated in the work environment each time the pick tip contacts the rock surface. Additionally, the generated dust can be reintroduced into the air further down in production, such as at transfer points. The purpose of this study is to characterize respirable dust particles generated at the pick tip at two stages of pick wear: new and moderately worn. Understanding dust characteristics in terms of concentration, size distribution, and particle shape throughout the life-cycle of the pick will provide a basis to mine and tunnel operators for changing out picks to mitigate dust generation at the source. This paper discusses the dust characteristics generated from preliminary full-scale cutting tests in a laboratory of an igneous rock block cut with conical picks at new and moderately worn levels of wear. The moderately worn pick generated a size distribution that favored smaller particle sizes compared to the new pick. The moderately worn pick also generated more overall dust, as the concentration level in mg/m3 was over double the amount of the new pick. Lastly, both picks generated particles that had similar aspect ratios and roundness measures.

May 18, 2022