Search Documents

By Victor S. Sazhin, Alexander Kostenko

The hydrochemical method, which is based on the separation of aluminium oxide and silicon oxide by the hydrothermal decomposition of aluminosilicates by alkaline solutions in the presence of calcium oxide, can be effectively used for the complex processing of high-silicon aluminium ores. In this case, the silica is bound to a slightly soluble compound: Na20.2Ca0.2Si02•H20 (under the conditions: [&k]= 9, CaO/SiO2 = 1.05, alkali concentration in the solution: over 300 g/l Na20, T = 240...300 °C). If alkaline solutions of 100...150 g/l Na20 concentration are used, Ca0•SiO2•H20 or 2Ca0•Si02.0.5H20 compounds, depending on calcium oxide dosage, are formed at 280...320 °C. New methods for the crystallization of Na20.Al203.2.5H2O from concentrated alkaline solutions rand low-concentration solutions are proposed to isolate aluminium from solutions. The hydrochemical method, which involves no sintering process allows one to decrease the expenditure of heat by a factor of two, to reduce the investment and to exclude the pollution of the ambient air by dust-laden gases. The expansion of the raw-material resources base of

Jan 1, 1984

By D. B. Sikka, R. B. Bhappu

Porphyry-type copper-molybdenum (Cu-Mo) deposits typically occur in the Phanerozoic rocks and have been well-documented. During the past two decades, a number of porphyry-type Cu-Mo deposits that range in age from 1055 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India. Namibia and Zambia. The Malanjkhand porphyry copper deposit M.P., India is estimated to contain 789 Mt (870 million st) averaging 0.83% copper (mill headgrade); 0.004% molybdenum; 0.2 g/t (0.006 oz/st) gold; 6 g/t (0.175 oz/st) silver and a cap of 7.5 Mt (8.2 million st) of oxide ore averaging 0.8% copper. The economic potential of the expanded copper mining milling, smelting and refining complex is expected to yield cathode copper 118.6 kt (130,700 st); molybdic oxide 830 t (914 st); gold 1.9 t (61,732 oz); silver 46.6 t (1.5 million oz); sulfuric acid 240 kt (264,500 st), copper from leach dumps 11.5 kt (12,600 st); nickel 24 t (26,400 st); cobalt 84 t (92,600 st); bismuth 16 t (17.6 st); selenium 48 t (53 st), tellurium 4.8 t (5.3 st).

Jan 1, 1995

By Roy Eric Lurie

Computer based signal processing techniques for obtaining empirical dynamic models from measured mill circuit data are discussed. This modelling is the first step towards designing a particle size control strategy. Experimental data from a computerized acquisition sys tern is examined and analysed, and a number of model identification procedures are applied. The resulting models are compared and a suitable model is selected, illustrating the benefits of computer tools for control system design.

Jan 1, 1992

By John W. Wilson

INTRODUCTION In the past, the cost and time required for the construction of shafts has played an important part in the planning of underground mines. For reasons that are discussed later, the economics and technology of shaft construction in the future can be expected to play an even greater role in the planning of new mines and the operation of existing mines. Indeed, the very feasibility of a proposed mining venture may depend on the cost and timing of the shaft requirements. The most commonly used shaft sinking methods used today for excavating vertical shafts are discussed and the need for new technology and methods emphasized. In one study by the U. S. Bureau of Mines, it was reported that the coal industry in the United States alone could require 170 to 190 new shafts per year on the basis of doubling current production by the mid 1980's or 70 to 90 shafts on a more moderate coal production expansion program. This study concluded that the attainment of the required number of shafts would be unlikely with the present shaft sinking resources and costs. In order to meet the requirements for shafts in the United States coal and metal mining industries, more efficient and speedier shaft construction methods will be necessary. Current shaft sinking methods are, in the main, labor intensive, and it is noteworthy that it is becoming increasingly difficult to attract the work force required to sink shafts conventionally. Because of this situation, some attempts at mechanization have been made to compensate for this ever-increasing scarcity of trained

Jan 1, 1976

By L. G. Martin

Early mining at Manhattan demonstrated that blasthole assays alone were insufficient to control the disposition of material. A program was began using controlled blasting, intense sampling and panning of crushed samples, fire assay checks, and geologic inspections to sort material in the pits. Statistical data confirms that the method provides effective control at minimal cost. This cost is easily offset by additional tonnage found in areas considered to be waste.

Jan 1, 1980

By R. J. Barnes

Consider a typical blast at a surface gold mine in North America. For example, the low-grade area of Bench 4000 at AMAX Gold's Sleeper Mine (Winnemucca, Nevada). Bench 4000 is 20 feet high (=6m) , and blast holes are drilled and sampled on a 14 foot by 14 foot square grid (a4m x 4m). A representative blast includes between 50 and 150 holes, encompassing 15,000 to 45,000 tons of material (w14,000 to 41,000 metric tons).

Jan 1, 1989

By Hillary W. St. Clair

In a previous report 1/the author showed that the essential information from particle size analyses of grinding mill products can be represented by three or four parameters derived from the first four moments of the particle size data. These parameters may be used in gamma or beta distribution functions to estimate the weight fraction in any given size range. Moment analysis was used to study the progressive changes that take place in particle size distribution when a homogeneous isotropic mineral such as quartz is reduced in size by impact crushing. 2/ This report briefly reviews the essential features of moment analysis and describes extension of this method to size reduction by ball mill grinding.

Jan 1, 1972

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By J. R. Johanson

In recent years the procedures for functionally designing bulk storage bins and hoppers have evolved from qualitative guess and try methods to a quantative method based on theory and tests of the bulk solid to be stored. This quantative method, developed and implemented by Dr.'s A. W. Jenike and J. R. Johanson as with any new design, must prove its effectiveness and validity in the actual operation of the finished equipment. How accurate are the theoretical predictions? Is it possible to extrapolate from bench size tests on a small ample of the bulk solid to the full scale bin design? Can the theoretical designs be economically translated into working hardware? In this paper the answers to these questions are discussed in light of actual bin operations.

Jan 1, 1968

By Pradip

It is possible to beneficiate low-grade phosphate ore slimes containing predominantly siliceous gangue by a combined selective flocculation-flotation scheme using commercially available reagents. The presence of clays, in particular, montmorillonite and attapulgite, has a disastrous effect on the efficiency of separation. Suitable remedies to overcome this problem are not yet available. Intensive R&D efforts are required in the areas of the design and synthesis of specific reagents, the effect of particle size, and the design of appropriate process equipment to carry out flocculation and flotation of slimes.

Jan 1, 1989

By D. Butler

Subsurface density changes can be detected by very precise surface gravity measurements. A feasibility study, combined with field experience using modern instruments, will indicate the probability of success. In addition to projected anomaly parameters, surface conditions that effect the survey precision must be evaluated. Examples with excavated zones at 9 m (30 ft) of depth and [+] 22 microgal error are compared to the same model at 30 m (98 ft) of depth. The figures illustrate anomaly detectability. The survey error is a function of surface topography and lateral density variation in the very near surface.

Jan 1, 1990

By Eleanore L. Nestlerode, James R. Guilinger

In April. 1990 Addwest Minerals acquired the Phillips Ranch sulfur property. The sulfur deposit, hosted by the Permian Castile anhydrite, occurs as two distinct elongate. parallel orebodies within a series of northeast-trending grabens. After completing a positive feasibility study, based, in part. on successful drilling programs by Addwest Minerals and previous operators, the decision was made to place the property into production. Utilizing an existing on-site kasch plant, plus significant portions of the recently purchased Texasgulf Comanche Creek Frasch plant. Addwest is currently constructing an 800 long ton per day Frasch mining facility.

Jan 1, 1992

By Evert Hoek

Two types of failure have to be considered in designing large openings: (a) Structurally controlled failure caused by discontinuity intersections, (b) Stress induced instability which occurs when induced stresses exceed the rock mass strength. Structurally controlled failures, which occur in hard jointed rock masses at relatively shallow depth, are briefly reviewed. This paper is primarily concerned with stress induced instability at greater depths and with the problem of estimating the strength of a rock mass surrounding an underground opening. Some of the practical aspects of support design for large openings are discussed.

Jan 1, 1981

By Craig J. Brown

Despite its great potential utility, ion exchange has only achieved limited application in hydrometallurgy. To a significant extent this is due to the limitations of conventional ion exchange process design as well as the properties of the ion exchange resins themselves. Over the past decade several new ion exchange resins have been introduced with properties that make them potentially very useful for various hydrometallurgical separations. In addition, a novel ion exchange process called Reciprocating Flow Ion Exchange or Recoflo, which has been employed in the metal finishing industry for the last dozen or so years for chemical recovery and effluent treatment, has been shown to offer a number of unique and significant advantages over conventional I.X. technology.

Jan 1, 1984

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By Satyam Tiwari, Sarat Kumar Das

Tailings from mines and industries impose danger to the environment as evidenced by the recent failures of tailing storage dams. The tailings are mostly non-plastic with silt-size particles, but their behavior is largely dependent on the extreme void ratios of the material. Hence, the critical state provides an appropriate perspective in explaining the behavior of these geomaterials. Based on a comprehensive dataset of non-plastic tailings and non-plastic soils, an attempt has been made here to correlate critical state parameters to extreme void ratios and stress parameters. A hybrid algorithm with multi-objective feature selection (MOFS) and extreme learning machine (ELM) was used to establish the correlation and to identify the most influential input parameters. Based on the information from the proposed hybrid algorithm, a comprehensive prediction model is proposed using multi-gene genetic programming (MGGP) algorithm to facilitate quick estimation of critical state parameters. The performance of both models has been assessed using several performance metrics. The results from the study indicate that hybrid MOFS algorithms perform very well in the prediction of critical state line parameters and the identification of influential features. The findings of the study have significant implications for future research on the safe management of tailing storage facilities.

Dec 22, 2023

By Yuting Xue, Khaled Mohamed

The failure of coal ribs is a major hazard in underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have been working on the development of an engineering-based rib control method. A user-friendly standalone application, called Design of Rib Support (DORS), is being developed to ease the calculations of rib support. DORS can estimate the Primary Rib Support Density (PRSD, ton/ft2) for development loading. However, it still needs to take account of another key factor, bolt length, in rib support design. The bolt length can be estimated from the rib fracture depth, and this study focuses on the coal rib fracture depth analysis with numerical modeling and artificial neural network. A total of 331 FLAC3D simulations with different mining scenarios and rib conditions were conducted for this study. Machine learning was then used to predict coal rib fracture depth under different conditions. Based on the numerical simulations, the parameters for mining scenarios and rib conditions were collected as features for machine learning, and coal rib fracture depths were collected as the target to predict. Good data correlation (r-square) was obtained with the use of an artificial neural network. The

By J. M. W. Mackenzie

Three major developments have dominated the recovery of gold from ores, viz; 1846 Elsner's studies of gold solubility in aerated alkaline cyanide solutions 1887 MacArthur and Forrest's process based on zinc precipitation 1980+ Large scale development of the CIP process The brevity of this list for a metal whose extractive metallurgy has been as widely studied as any metal reflects the fact that the chemistry of the gold recovery process, as opposed to the engineering has seen few significant breakthroughs in over a century of application. to The purpose of this paper is introduce a new chemistry for gold recovery which may, in the future, add significantly to the technology of gold recovery. This new chemistry is based guanidine functionality - (R2R2N) 2 C = N R2 on the In developing the use of the guanidine functionality for the recovery of gold as the aurocyanide anion from leach solutions and pulps, Henkel has, as its objective, the development of an effective gold selective ion exchange resin. As will be seen, the initial investigation of the properties of the guanidine functionality in the solvent form for gold recovery lead to some significant metallurgical developments of their own but, the foremost objective was, and remains, the development of a resin for gold recovery. As a part of this development project, Henkel has entered into association with Mintek, South Africa, and this ongoing association has the potential to develop RIP/RIS technology for the gold industry. More details on Henkel's gold recovery technology and Mintek's role in this programme are given in (1). an The application of ion exchange resins to gold recovery is not new and many reviews have been published on the advantages of this process, and on the current state of the art of gold recovery by ion exchange resins. (2)(3)(4) Widespread application of ion exchange resin based processes for gold recovery has, however, not occurred to date. Fleming and Cromberge (5), described some significant pilot plant RIP trials in South Africa and the partial success of these pilot plant trials held out the tantalising possibility of a breakthrough in gold recovery based on RIP technology. Despite this pioneering work, only two really significant applications of RIP technology for gold recovery exist today. These are the Golden Jubilee Plant in the Eastern Transvaal South Africa and the widespread, although in some respects technically backward, use of ion exchange for gold recovery in the former USSR. There are two main reasons for the current scarcity of RIP and RIS plants used for gold recovery. These are: 1. 2. The perceived problems of engineering RIP plants The lack of a resin having suitable chemistry for both gold loading and gold elution The problems of engineering RIP plants have been largely overcome in the last 25 years. Much of the development in RIP plant design took place in the uranium industry during the rapid expansion of that industry in the mid 1970's. In addition, the development of CIP engineering systems has lead to the development of in-pulp solid extractant based metallurgical plant designs which can, with limited modification, be adopted to RIP. The lack of a resin having suitable chemical properties has almost certainly been the main reason for RIP/RIS not being introduced into the gold industry over the past decade. Attempts to use RIP/RIS have focussed on either conventional we ak base or conventional strong base resins. The weak. base resins have the disadvantage that they

Jan 1, 1993

By Earl Sackett

In its 110-year history as a mining camp, the Boleo copper district of Baja California has weathered significant changes in its operation, ownership, and profitability, despite an inhospitable environment and unique ore body. For some 65 years, under the operation of Compagnie Boleo, the area ranked as the second largest copper producing district in Mexico, with over 560 km of underground workings. As its ore grade-and profitability-declined, operations continued sporadically and with varying degrees of success. Today, operations at Boleo are maintained -despite the economics -while work is underway to devise a viable metallurgical process. Lab tests on a hydrometallurgical method look encouraging and, though this may end the district's days as a mining camp, the feasibility of the process may result in an 18-kt/d full-scale operation.

Jan 7, 1980

By F. F. Aplan, V. Choudhry

This investigation is an exploratory study to evaluate a large number of potential pyrite depressants for use during coal flotation. Subsequently, the more promising reagents can be evaluated in detail. Several reagent categories (such as alkalis, lime, oxidizing agents, reducing agents, specific inorganic ions and dispersants) that were found to be effective pyrite depressants are discussed here. Other pyrite depressants will be discussed in Parts II and III.

Jan 1, 1993