Search Documents

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016

By I. R. McGowan, J. Tilk, J. I. Hershman, R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1998

By S. K. Kawatra, S. Bagley, T. C. Eisele

To meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1988

By H. G. Linge

The Australian gold industry currently contributes some $4bpa to the national economy [l]. Some 40% of the total gold is produced in the region centred on Kalgoorlie known as the Eastern Goldfields of Western Australia. This region is the largest single centre of production with an output of some 100 tpa of gold [2]. In the Eastern Goldfields, refractory arseno­pyritic gold ore is an increasingly significant source of gold, feeding several operations utilizing bio-oxidation as the pre­carbon in pulp/leach (CIP/L) treatment process [1]. This paper desribes an alternative pre-CIP/L treatment option for use in the Eastern Goldfields based on the chlorination of arsenopyrite by chlor-alkali technology [3] using the salt resources available from saline water present in abundance in the region.

Jan 1, 1995

By R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1997

By Robin P. Gardner

The development and use of short-lived radioactive tracer methods for the on-stream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a-large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1978

By Marc E. Orman, Mark E. Smith

Regulatory and environmental concerns continue to broaden the range of mine wastes that must be capped with low permeabili­ty liner systems at closure. The mining industry has been a leader in developing liner technology for leach pads and tailings impoundments, but it is a newcomer to cap designs. Closure of waste piles, leach heaps and tailings require special design con­siderations. Factos such as differential settlement, surface ero­sion, veneer stability, vegetation and burrowing animals must be considered.

Jan 1, 1996

By J. P. Sieverson

The Comprehensive Environmental Response, compensation, and Liability Act (CERCLA -commonly referred to as Superfund) was passed into law in December 1980 in the wake of such incidents as Love Canal and the Valley of the Drums. Superfund was originally perceived as a way of cleaning up spills of hazardous substances and/or cleaning up abandoned hazardous waste dumpsites. In February 1981, Michael Cook, EPA deputy assistant administrator for hazardous emergency response, called Superfund "a tremendously powerful law. It could revolutionize the way the environment is protected, but we certainly don't intend to realize the full potential of the law for some time." These words have proven prophetic for Asarco's East Helena Smelter.

Jan 1, 1988

By T. Y. Yan

The various ion exchange reactions occurring during the restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column using line saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500 to 3 ppm. The presence of NaCl in the restoration fluid is beneficial in + improving the selectivity of the system for NH removal and reducing ca++ ion consumption.

Jan 1, 1982

Automated drilling in surface mines is here, it?s successful, and it?s already at work in mines around the globe. Coal, copper, iron and gold mines in large mining countries such as Canada, Australia, South Africa, the United States and Chile are meeting mining objectives previously ruled out as unattainable. Pit Viper automation enables operators to accomplish more objectives safely. Operator assist functions like AutoLevel, AutoDrill, Auto Rod Changer and multi-rig teleremote control are a few of the features mines are using to gain consistent, sustainable productivity.

By 000-000-604

HISTORIACAL INTRODUCTION Mineral processing has three principle branches, to quote Taggart, "Ore Dressing, which comprises the methods of separation of solids in inorganic crude by means which do not affect substantial chemical change; Extractive Metallurgy, which utilizes chemical reactions for separations of constituents from solids in inorganic crude; and, Fuel Technology, which employs both physical and chemical methods for separating and rearrangement of liquid gaseous and solid components in crude oil and natural gas, tar sands, shale oil, or coal." The scope of this handbook covers the first two classifications, that is, "ore dressing" and "extractive metallurgy," which have been combined in one term: "mineral processing." For a brief history of the development of mineral processing, one could well refer to the Introduction, Sec. I of the Handbook of Mineral Dressing by Taggart, Froth Flotation, Principles of Mineral Dressing by Gaudin, and the original Richard's Ore Dressing, volume No. 1, first published in 1903-1905. In these references and the references given in them a coverage of the history of "ore dressing" can be found and studied at the reader's leisure. For the history of extractive metallurgy as well as ore dressing, the bibliography in General References, taken from a History of Ex¬tractive Metallurgy by F. Habashi, will give a good background for those who are interested in more detail on the history of metallurgy in general. Mineral processing covers a very wide field as is illustrated by the topics discussed in Part II of this handbook and dates back to the early history of man which started with the production and use of native minerals such as gold, silver, copper, mercury, and meteoric iron which were washed or picked from deposits on the surface of the earth and worked because of their malleability. Later, melting was discovered and then it was possible to cast objects of these metals, excluding mercury. The discovery of a method for reducing the metal¬lic oxide probably was developed from melting fragments of oxides or roasted sulfides with charcoal, so that the native metal could be produced in simple blast furnaces such as are used today in rural parts of Spain, China, and elsewhere. Eventually, it was learned that iron could be readily worked when hot, which resulted in its replacing bronze for tools, weapons, and cutlery. Carbon dating and correlation with the Brittle Cone pine has

Jan 1, 1985

By John C. Stankus, Xiaoting Li

"Underground structures such as square/arch steel sets, king beam structure, etc. are widely used for the roof support in underground mines. In designing and calculating the required carrying capacities of these underground structures, how to identify the potential rock loads on the structures over long term is a challenging question for ground control engineers. Based on design practices of both surface and underground structures, the authors have designed and applied appropriate load factors in underground structural design projects to accommodate different rock types, entry/intersection dimensions, roof geologic conditions, availability of roof bolts and water, etc. Classification of load (reduction) factors for large-span underground intersections are presented for reference. Success of designed underground structures in effectively controlling roof stability over years indicates the applicability of the load factor concept for underground structural design, and its same significance as of the load factor specifications in ASCE/SEI 7-10, ANSI/AWC NDS (2015), and AASHTO LRFD Bridge Design Specifications (2012). The load factor concept will facilitate ground control engineers to appropriately utilize popular structural design software, such as RISA-3D or -2D to efficiently design and analyze underground structures.LOAD FACTORS IN STRUCTURE DESIGN APPLICATIONSIn structures, loads cause stresses, deformations, and displacements. Assessment of their effects is carried out by the methods of structural analysis with the help of load factors. Loads can be increased or decreased by load factors to meet the requirement that design strength be higher than maximum loads. For example, in designing a staircase, a dead load factor may be 1.2 times the weight of the structure, and a live load factor may be 1.6 times the maximum expected live load based on the Load and Resistance Factor Design (LRFD) method. These two “factored loads” are combined (added) to determine the “required strength” of the staircase. Some typical load (adjustment) factors used for structural design are as follows:"

Jan 1, 2019

By Hayward B. Oblad, Gary F. Meenan

Two optoelectronic detectors were developed by CONSOL R&D for fine coal processing applications. One sensing device is used to estimate the amount of fine coal in the solids fraction of the froth flotation tailings slurry. The other probe, based on similar technology, is capable of measuring sol ids concentrations as high as 10 weight percent in fine coal slurry streams. These patented optoelectronic sensors are installed in several CONSOL coal preparation plants and are an integral part of the fine-coal control systems.

Jan 1, 1993

By Samantha Smith

Nautilus is completing the world's first environmental impact assessment (EIA) of seafloor mineral extraction and Nautilus has gained extensive experience conducting environmental studies in subsea environments. Nautilus is currently working on the Solwara 1 Project in the Bismarck Sea, Papua New Guinea, where high grade seafloor massive sulfide deposits lie at ~1600 m water depth. Conducting an EIA in the deep sea presents some interesting and exciting challenges. Seafloor studies commenced in December 2005 using a remotely operated vehicle (ROV) fitted out with highly specialized scientific equipment to conduct water quality, sediment, biological and oceanographic studies. During 2007 and 2008, Nautilus launched two two 30-day ROV programs dedicated to environmental baseline studies and during this campaign, over 550 biological, sediment and water samples were collected and over 20,000 seafloor observations were logged. On board specialists included an international team of experts in the field of deep sea marine science. Collaboration between industry and scientific research institutions allows data to be collected for the EIA but also provides an extraordinary opportunity for researchers to access sites that might otherwise remain unobtainable to science. This presentation will review the studies conducted as part of this exciting project. Keywords: Seafloor Massive Sulfides, Environmental Impact Assessment

Jan 1, 2008

By J. S. Chen

DOE recently funded 21 projects under the solicitation by its Environmental Restoration and Waste Management Division. This project is combining the expertise of an interdisciplinary team of researchers with that of three manufacturers to isolate nuclear waste storage sites using remote longwall mining. The concept is being pursued in Germany, too. This paper will present the conceptual approach to the project and discuss the problems in transferring longwall mining technology to nuclear waste containment.

Jan 1, 1994

By V. R. Degner

Comments Summary It is very interesting to review the technical changes which have occurred in the industrial practice of minerals flotation over the past two decades. In 1972, worldwide industrial flotation was dominated by 'mechanical' flotation machines having an individual cell volume less than 500 cu.ft. Manufactures, such as DENVER Eqpt. Co., OUTOKUMPU, WEMCO, GALIGHER (AGITAIR), AKKER, and later DORR-OLIVER, produced flotation machines featuring a mechanical rotating impeller which served to mix pulp and air, prior to flotation, and to keep the solid ore particles in suspension. While sharing this common mechanical impeller feature, the machine design of the various manufactures differed in detail; particularly in regard to the vertical location of the impeller in the cell and the means by which flotation air was brought into contact with the pulp within the rotor mechanism. A review of the existing technical literature in 1972 would identify academic research studies, particularly at Columbia University (N. Arbiter, C, Harris ...) aimed at comparing flotation cell design concepts, of the various machine manufactures, on a hydrodynamic basis. These research studies were confined to very small, laboratory bench size, flotation machines, and the benefits of incorporating hydrodynamic considerations in the scale-up of the existing 300 cu.ft. mechanical flotation technology to larger cells was not commonly practiced industrially. Technological advances in minerals flotation, over the past two decades, have been influenced by a variety of economic factors including the increasing development of lower grade ore bodies, the attractions of producing a higher grade final concentrate, and the economy of tails retreatment to improve overall plant recovery performance, and flotation system “optimization" became increasingly important through the 1970-80 time period. The trend toward processing lower grade ores led to higher tonnage mill operations, and stimulated the development of the very large capacity mechanical flotation machine for roughing and scavenging duty. In 1972, the 500 cu.ft. size flotation machine was being pilot tested and introduced to the industrial market. Today, 1993, individual cell volumes of 1500-3000 cu.ft. are operating successfully throughout the world, and well planned plant test programs have concluded that the very large flotation machine can achieve the same metallurgical performance level of its smaller predecessor. The large flotation machine development record clearly credits the incorporation of internal cell hydrodynamic considerations in guiding the scale-up of the mechanical flotation machine to large sizes. This guidance eliminated, or reduced significantly, costly in-plant prototype machine changes which increase Dramatically with increasing flotation machine size. Early in the 1980's, at approximately the time that flotation machines in the 1500 cu.ft. class were being introduced into the market, it became evident that the availability of the very large mechanical flotation machine brought with it the need for a systematic means to "optimize" the flotation system by relating flotation cell size, row length (i.e. number of cells per row), and flotation rougher, scavenger, and cleaner system configuration to the economic objectives of the concentrators' operating management. Flotation system optimization consists of quantifying the flotation process performance using a suitable model which relates the kinetic response of the trace specie and the gangue material to the cell overflow, and produces a numerical relationship between product grade and value recovery. The computer analysis technique has proven to be an invaluable tool in determining the kinetic model coefficients which characterize a given application, and is also used to apply the resulting model to a proposed minerals beneficiation situation seeking to "optimize" the flotation system by relating metallurgical grade-recovery performance, flotation cell size, and circuit arrangement, to plant space, installation, and operating costs. It is interesting to note that these same computer based kinetic flotation analysis techniques can be easily applied to quantitatively evaluate the effect of different chemical reagent strategies, and flotation air transfer, on process performance for a variety of candidate feed ore types.

Jan 1, 1993

By Robert C. Freas

Over the past twenty years people throughout the world, but particularly in the United States, have been taking an increasing interest in the environment, sources and causes of pollution, and pollution abatement. Air quality in the United States has been and continues to be an area of primary emphasis. In 1970, the US Congress passed the Clean Air Act and subsequently revised and strengthened it in 1977 with the issuance of the New Source Performance Standards. The Act has been further strengthened with the passage of the 1990 Amendments. By far the largest single source of sulfur dioxide (SO,) pollutants are coal fued electric generating power stations. Hence, a substantial portion of the flue gas desulfurization (FGD) research and equipment installation has been geared to the utility industry. Several competing FGD technologies were touted during the period 1970 to 1990 with varying degrees of success. Subsequently, the more successful technologies have been accepted, revised, and improved to the point that by 1991 third and fourth generation technology is available. A second area of emphasis for FGD has been coal fired industrial boilers. While individually they are much smaller than any electric utility generating station, they do represent a significant source of sulfur pollution. However, due to the size of industrial boilers and their location within industrial and educational complexes, the wet scrubber technology being employed by the utilities is not appropriate for these applications. Hence, fluidized bed combustion (FBC) technology has been developed for the industrial boilers. Since the installation of the first full scale test unit at Georgetown University, several equipment vendors have come forward with an increasing array of more sophisticated FBC units. Currently, FBC technology has matured to the point that the Tennessee Valley Authority (TVA), in cooperation with the Electric Power Research Institute (EPRI), has installed an FBC system on a 250 MW test unit at the Shawnee Power Station in Kentucky.

Jan 1, 1994

By M. Galetakis, C. Roumpos

A sustainable coal industry needs to achieve a number objectives concerning mainly with superior utilisation of deposits and improved environmental performance. Modern quality control systems, which are greatly based on the on-line analysers, play an important role in achieving sustainability targets. This paper discusses the testing and application of on-line ash analysers installed in the Ptolemais and Megalopolis lignite mines in Greece and examines the possibility of using this type of analyser to control blending and homogenisation operations. The effect of the accuracy of on-line analyser to control process, when used for the characterization of low rank coals with complex and variable composition, such as greek lignites, is examined.

Jan 1, 2005

By Weibai Hu

Four methods to assess the relative flotability of fine coal have been tested: flotation with frother only, flotation with frother and collector, salt flotation, and timed-release analysis. A practical and simple criterion which combines the separation efficiency (capacity factor and kinetic rate constant (intensity factor) has been suggested. Five coal samples are chosen and tested. Based on test results, it is concluded that the flotability test with collector and frother is closer to practice, and, according to the suggested flotability criterion, coal fines can be classified into four categories of relative flotability: very easy, easy, moderate, and difficult.

Jan 1, 1987

By M. M. Fine

One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. To cite some of them, in May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.3/ More recently, November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials, Evian, France, May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then current interest must be at a high level. To the casual observer of the metallurgical scene, the abiding and recurring attention to iron ore reduction outside the blast furnace must be somewhat puzzling in that so much research endeavor has resulted in so little commercial activity.

Jan 1, 1968