Search Documents

By P. Coleman, J. C. Kerkering, S. Iverson

Fault tree analysis is a systematic safety analysis tool that proceeds deductively from the occurrence of an undesired event (accident) to the identification of the root causes of that event. One recurring mine safety problem-a dozer falling into a void over a drawpoint on a coal surge pile-was analyzed using available, inexpensive fault tree programs on a personal computer. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between these various subordinate events as well as the various chain of events leading up to the primary event. A sensitivity analysis on these probabilities showed which events had the greatest influence on dozer burial in a coal surge pile.

Jan 1, 2001

By M. G. Vieira

This investigation addressed the possibility of producing pellet feed at a silica content of = 1.0% using a representative sample of Samarco´s mechanical flotation tailings. This sample contained 11.0% Fe and presented an F80 = 116 µm and a d50 = 63 µm. The higher silica content was verified in the coarser fractions and the higher iron content in the fraction -37 µm. Specular hematite is the most abundant mineralogical phase in the fraction -37 µm. The technological tests used one of four methods: magnetic concentration using a wet high-intensity magnetic separator, magnetic concentration using a SLon high-gradient magnetic separator, reverse flotation or direct flotation. The methods using the magnetic concentrator SLon, reverse flotation and direct flotation did not present results meeting the target of the study: iron content in the concentrate (rougher stage) greater than 34% or iron recovery greater than 80%. Cleaner stages were not achievable with the resulting concentrates. In contrast, the most successful method consisted of using wet high-intensity magnetic separators (WHIMS) as a rougher stage and reverse flotation as a cleaner stage. Using this route, it was possible to produce a pellet feed with a silica grade of 1.0% and high specular hematite content.

Jan 1, 2010

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration, and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. Suppressant effectiveness was also improved using hygroscopic reagents which retained moisture, improving longevity. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product's particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM's continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM's accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health(NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

Jan 1, 2003

By M. Akser, F. L. Pirkle, B. W. Stratford, B. Ipekoglu

To date, no ilmenite, rutile and zircon deposits of commercial importance have been reported in Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit in the vicinity of Ormanli, which is located northwest of Istanbul along Turkey's Black Sea Coast. Consequently, beach coil sand-dune samples were collected from that area for additional analysis. Laboratory methodologies drat were designed to simulate standard industrial heavy-mineral plant practices were used to analyze and evaluate the samples. Based on these analyses and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1997

By G. Barelli, C. Giusti, W. H. Langer

Natural aggregate – sand, gravel, and crushed stone – is the number one non-energy mineral resource in the world in terms of both volume and value. A plan for the sustainable development of aggregate resources can include: 1) policies and economic incentives to encourage identification and protection of potential resources, 2)efficient quarrying and processing of aggregate, 3) efficient use of primary aggregates, 4) greater use of recycled, waste, or substitute material, 5) inclusion of costs of all environmental impacts in price of material, 6) reclamation to beneficial secondary uses, and 7)identification of objectives, targets, actions, and sustainability indicators. Quarrying can also contribute to sustainable ecosystems through natural habitat reclamation.

Jan 1, 2003

By E. Valdiviezo, J. F. Oliveira

Adsorption of residual flotation reagents onto equilibrium fluid cracking catalysts is a promising method of purification of flotation process water. In the present paper, adsorption of sodium dodecyl sulphate (SDS), dodecyl ammonium chloride (DAC) and sodium oleate onto a spent catalyst from petroleum industry was studied by analysing the residual concentration of the surfactant after contact with the zeolite catalyst. The adsorption of the DAC was rather low but SDS and sodium oleate presented a high affinity for the catalyst surface. The loading capacity was 4.2 kg/ton for SDS and 5.5 kg/ton for oleic acid. After the treatment of the loaded catalyst with a HCI 1 N solution these surfactants are desorbed and the catalyst may thus be regenerated. This would be an additional advantage to its low cost, not to mention its condition as a discarded product and its availability in large tonnages.

Jan 1, 1995

By Paul D. Tomlingson

Editor's note: This is the second of two articles on maintenance. Part one: "Downsizing maintenance to improve performance: Defining the downsizing task," appeared in the September issue of MINING ENGINEERING, pp. 1065-1066. Part one explained that downsizing must he an organizational change in which the mine moves to a more efficient, smaller maintenance organization. But the new, smaller organization must operate more productively. Determine initial reduction targets Reduce the workload - The initial reduction target can be determined by projecting manpower reduction as a result of discontinuing or deferring work. Start these reductions by not replacing personnel who retire or are disabled. Observe the right craft mix during this initial reduction. Improve productivity - Further reductions can come from better productivity. But achieving the higher productivity level will require a year or more. During this transition, the efficiencies of a well-defined program and a team organization must take hold.

Jan 1, 1994

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

This research contributes to BioMinE (http://biomine.brgm.fr), an integrated European Union project of the Sixth Framework Programme. The general objective of BioMinE is the development and integration of innovative, environmentally friendly, biohydrometallurgical processes for the recovery of metals from primary and secondary resources within Europe. The work presented in this paper deals with the initial plan of study on the sustainable use of solid wastes derived from bio-processing of European metal bearing resources. The approach involves solidifying the waste into cementitious waste composites analogous to controlled low-strength materials (CLSM). The aim is to achieve composites of adequate mechanical, physicochemical and environmental integrity, thus providing a sustainable solution for dealing with such bulk products which are conventionally unmarketable and therefore normally discarded to landfill. Assessment has been based on largely ?model? wastes anticipated to be similar to bio-processing wastes. These include an ochreous mine water sludge and an industrial goethite residue. The work indicates that wastes containing high iron and calcium contents, typical of products from bioleaching of concentrates, could be beneficially reformed as CLSM of appropriate compressive strength. Due to the high water contents of these composites, porosity and hydraulic conductivity were correspondingly high. Flow-through leach tests showed some resistance to immobilisation of toxic elements. Work is continuing to reduce the risk of toxic elements leaching under environmental conditions. This will include laboratory-scale encapsulated systems of CLSM, designed and tested to produce a novel type of engineered fill structure.

Jan 1, 2006

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, super-conductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Jan 1, 2011

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, superconductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Nov 1, 2011

By M. Murphy

The multibillion dollar cost of cleaning up thousands of environmentally contaminated sites across the country created by decades of inadequate disposal of hazardous waste has led to a search for "deep-pocket" sources of cleanup funds. The resul1:: is the emergence of a growing body of law that could have a profound impact on commercial financing transactions and other investment activities when present or past owners of contaminated property are involved.

Jan 1, 1988

By P. Tsakiris

The increasing social interest for the environmental issues, forces the authorities to enact more rigorous regulations. The mining industry is one of the sectors that concentrate vigorous remonstrance. It is an absolutely justified reaction, as a result of the numerous contaminated and polluted sites that have been inherited by previous operations and they remain unremedied. The lack of a consolidated global legislation, transfers the burden of decisions to the national level. This paper consists of two parts. At the first part, it discusses the critical role of the state to form an effective environmental policy, feasible for the context of the national economy. Afterwards it analyses two of the main points, which must be considered by the regulator for the excavation activity, the abandoned sites and the duration of the mining investment. The aims are to defuse, in the short-term, the public pressure, protecting the economic growth and, at the same time, to form a basic structure for the development of the corporate social responsibility. The second part presents an alternative financial instrument for the Greek regulatory framework, conformed to the characteristics of the Greek Economy, and analyses the expected benefits both for the business and the social welfare.

Jan 1, 2002

By Kurt Burg, Allen Reicks

Tapered clamping devices have been used successfully over the years to transmit torque and bending loads from conveyor drives to conveyor belts. Proper design and application is important in the successful operation of these key components. This paper includes a historical review of component design and application and an overview of the important dynamics and limiting factors. Actual applications and simulation models are used to demonstrate the correct use of these devices.

Jan 1, 2002

By José Salim, T. V. Subrahmanyan

The occurence of primary stratiform and vein gold deposits in the Precambrian rocks of Northeastern Brazil is discussed. The stratiform deposits are related to clastic sediments (quartzites and conglomerates). The veins are associated with quartz and sulfides and are structurally controlled by shear zones. The gold was recovered for a long time by small miners. Developmental programmes for large scale mining are now envisaged. The recovery problems and gold economics are also discussed.

Jan 1, 1988