Search Documents

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By Malcolm J. McPherson, Satya Harpalani

A thorough knowledge of coal permeability and its variation with factors like stress conditions, and time, is useful in simulation studies of mine ventilation and coalbed methane recovery, as well as characterizing coalbed methane reservoirs. An experimental investigation was carried out to study the gas flow characteristics of coal to enhance the under- standing of the mechanism of methane flow through it. The work consisted of measurement of permeability of coal samples under triaxial stress and an examination of the physical structure of coal using electron microscopy. Effort was made to fit the experimental data to several phenomenological models that have been used to describe fluid flow through porous media. It was realized that gas flow through coal cannot be described by models that assume this flow to be through a bundle of capillary tubes. However, results suggest that this gas flow could be predominantly through fractures and cracks in coal, and this could be represented by flow between parallel plates.

Jan 1, 1986

By W. W. Wen

Approximately 3 percent of the raw coal processed in U. S. Steel coal-preparation plants ultimately reports to slurry- tailing disposal. The usual disposal method is to pump the refuse slurry containing the minus-48 mesh (300 µm) refuse into dams or impoundments that are constructed of the coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically urlfeasible or technically impossible. U, S. Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, Portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition it was decided to study the stabilization of fine-coal-refuse slurry through use of cement-type additives.

Jan 1, 1979

By R. P. King

INTRODUCTION It is now 21 years since Wiegel and Li published their paper on a random version of Gaudin's model for the mineral liberation phenomenon (Wiegel and Li, 1967). This paper was to revitalise interest in North America in one of the most fascinating, difficult and important problems in the field of theoretical mineral processing. Gaudin had many years previously (Gaudin, 1939) already presented a penetrating analysis of the problem and Wiegel and Li based their analysis very closely on the Gaudin model but they realised that the indeterminate geometrical structure of mineralogical materials demanded that only probabilistic models could provide the necessary quantitative information when working with real materials. They proposed and solved a randomised version of the Gaudin model but retained the essential geometrical simplicity of cubic mineral grains and a cubic fracture pattern. Although their model met with some limited success it was to be superseded in due course. During the 1940's and 1950's the classical field of geometrical probability spawned the mathematical discipline of integral geometry and as early as 1965, Bodziony (1965, a,b) showed that the techniques of integral geometry could accommodate the problems associated with the indeterminate nature of the geometrical mineralogical structure, provided that these were couched in probabilistic terms. In particular he showed that the quantitative description of the comminution process and that of liberation could be decoupled with the resulting economy of effort. This idea has profoundly influenced the course of research in liberation theory and has greatly facilitated its application and the measurement of liberation in a practical way. Bodziony demonstrated also that any theory that required the specification of the mineral "grain

Jan 1, 1989

By Tony Treasure, Ian Ewart

The EMEW® cell has been developed to overcome a number of inherent limitations in conventional electrowinning technology, particularly the high cost and restricted process windows characteristic of conventional hardware. The EMEW technology has been widely demonstrated to achieve high performance for various metals under chemical conditions well outside the limits required for efficient operation of conventional cells. In particular application of the EMEW cell for recovery of silver offers significant operating and capital cost advantages over conventional Merrill Crowe technology used for cyanide based solutions. The cell also offers process advantages for direct silver recovery from nitric acid solutions. The performance of the EMEW® cell on silver cyanide solutions, producing high grade silver metal in a single step, is accomplished by providing a physical mechanism which presents metal ions to the cathode on a highly efficient and continuous basis. The simplicity of design and operation of the EMEW cell offers the following advantages for silver recovery from cyanide or nitrate based solutions: • High grade product in a single step. • Selective for silver over other metals in the electrolyte. • Wide operating concentration range (100,000 - 5ppm). • Ability of the cell to operated in a variety of acid or alkaline electrolytes. (Cyanide, Nitrate). • Simple liquor reticulation. • No pretreatment required - Clarification, deaeration or zinc dust. • High cmTent density and current efficiency compared to conventional electrowinning cell. • Modular design allows for flexible operation and production rate. • Pilot plant results using full scale cell result in accurate scale up design. • Easy/fast installation - cell banks are delivered pre configured with piping and wiring. • Enclosed cell minimizes corrosive vapor and liquid losses in the circuit.

Jan 1, 2000

By Orville L. Lantto, Bruce K. Cantrell, Keith S. Olson

Approximately 10 to 20 pct of exhaust aerosol mass from diesel equipped vehicles operating without exhaust controls is attributable to particles in the 1.0-10 µm size range. Recent in-mine measurements suggest that, in addition to reducing overall exhaust aerosol mass concentrations, the use of waterbath exhaust conditioners (water scrubbers) may significantly reduce the concentration of diesel exhaust particles larger than approximately 0.5 µm aerodynamic diameter. This implies that a measurement system that discriminates between diesel and mineral dust aerosols on the basis of aerosol size would have different accuracies depending on use of a water scrubber. To test this hypothesis, laboratory measurements were made by the Bureau of Mines to determine diesel exhaust aerosol penetration efficiency through a water scrubber as a function of size and engine operating conditions. Size distributions were determined using a Micro-Orifice, Uniform Deposit Impactor. Concentrations of CO, CO2, NO x, O2 and gas-phase hydrocarbon concentrations were also measured. No significant effect was found for these gases other than a slight decrease in NOx emissions. The water scrubber served as a moderate aerosol control with reductions in mass concentrations of about 29±9 pct under most conditions. This reduction occurred for particles less than 0.2 µm and greater than 0.6 µm aerodynamic diameter. Coal dust aerosols are mostly larger than 0.8 µm aerodynamic diameter. With use of a water scrubber, separating the aerosol into two parts, greater and less than about 0.8 µm aerodynamic diameter during sampling, results in collection of diesel and coal dust aerosol accurate to within 10 pct. Without a water scrubber in operation, such a sampling protocol would only be accurate to approximately 15 pct.

Jan 1, 1991

By Andrzej Wala, Tom Altman, Tom Hughes

The University of Kentucky Mine Ventilation Manager (UKMVM) is a system that contains Level Five knowledge bases and comprises an expert mine ventilation management system. The package uses production rule language (PRL) to interpret data monitored from sensors, e.g., for airflow, temperature, and concentration of gases, in an underground mining environment. Activated from the PRL knowledge bases are Pascal subprograms which (1) organize the monitored data to set up emergency consultations, (2) display graphic representations of a mine's ventilation network with the latest sensor readings, (3) provide interactive updating of mine ventilation parameters, e.g., resistance changes, revised flow requirements, and new regulator and fan settings. Also activated from these knowledge bases are programs which (1) monitor airflow, temperature and gas concentrations from a physical mine ventilation model and (2) adjust regulator openings and fan rpm's. Thus, as an expert system the UKMVM not only presents advisory consultations for underground environmental emergencies, but also serves as an interface between the monitoring and responsive control aspects in the continuous maintenance of normal mine ventilation.

Jan 1, 1989

By Irwin R. Higgins, Richard S. Dennis

Acid recovery employs ion exchange resin as an adsorption media for the separation of inorganic acids from mixtures of acids and their metallic salts. This technology has been used to treat spent pickling and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. Acid recovery can also be used for electrolyte treatment to facilitate valuable metal recovery and to improve product quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process strong acid concentrations. TETRA'S CCIX™ continuous I-X contactor has been used successfully in a simple, continuous operating mode to separate acid from its salt. Efficient separation is enhanced by refluxing which allows acid to be produced as a salt-free product at nearly its original strength. Continuous treatment also recovers heat to the bath and improves metal quality due to consistent acid quality.

Jan 1, 1995

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997

By C. H. Bucknam

A suite of ore and waste rock materials was selected for the interlaboratory testing of combustion-infrared ("Leco") methods used to estimate carbonate and sulfide minerals present in test materials. The objective of the study is to develop ASTM standard methods to be used for metallurgical characterization of ore, acid drainage prediction for ore and waste during ore body evaluation, and for ore and waste control during the active mining of ore deposits. The results may be interpreted for classification of the materials according to their carbonate-sulfide or acid-base characteristics based on net carbonate value (NCV). The test materials were processed by x-ray diffraction and x-ray fluorescence (XRD-XRF) at Newmont Metallurgical Services (NMS) to obtain a semiquantitative mineralogical composition. Results of the interlaboratory testing for total carbon-sulfur, pyrolysis loss carbon-sulfur and hydrochloric acid residual carbon¬sulfur are compared with the mineralogical composition to aid in interpretation of the NCV classifications of the samples.

Jan 1, 2002

By F. S. Knoll

GENERAL INTRODUCTION Electrostatic separation has found a number of applications since its initial installation as a processing method. Three broad types of electrostatic installations are discussed in order to provide a practical guide for three widely divergent uses of electrostatic separation. Only operating and installation data are covered in detail. A detailed technical treatment on the various types of electrostatic separation described in this paper can be found in the literature by F. S. Knoll, J. B. Taylor and J. E. Lawer.8, 9 ELECTROSTATIC SEPARATION OF IRON ORE: WABDSH MINES, CANADA Introduction Electrostatic roll-type separator technology which had been in use in various forms since the 1920's evolved in the late 1940's when this separation process was developed and applied to the extraction of titanium bearing minerals from beach sands by J. H. Carpenter. Equipment design and industrial flowsheets developed for the recovery of rutile and ilmenite found new application in iron ore by chance in the year, 1956. From the time of the first beach sands plant, Carpco had developed other technology, gravity and magnetic separation to better serve the beach sands industry. It was in the fall of 1956 that an iron ore producer from the upper Michigan Peninsula sent a sample of jaspilite (fine-grained specular hematite in a jasper matrix) to Carpco's laboratory for the purpose of determining if a new high-intensity magnetic separator would be beneficial. Process Development W. P. Dyrenforth, while presenting a paper on the subject in the fall of 1957, recounts the laboratory tests. "High-intensity magnetic separators have been employed (for the beneficiation of iron ore) with some success and are still being investigated. Magnetic separation is a natural field of investigation, since iron and magnetism have been almost synonymous since ancient times. As a matter of fact, when Carpco first began investigating the possibilities of upgrading specular hematite, the first thought was in terms of magnetic separation; and the second thought was in terms of gravimetric separation. It was found

Jan 1, 1986

By W. S. Hannan

History Leaching of sulfide ore was first attempted by the Phelps Dodge Corporation about 1900 at Bisbee, Arizona, when Dr. James Douglas conducted experiments in an attempt to apply the leaching techniques then in use at Rio Tinto, Spain. Although this initital attempt was unsuccessful, research work was continued which culminated in successful leaching operations at Tyrone, New Mexico, in 1917 and at Bisbee beginning in 1920. Leaching has continued intermittently since that date, with material from the Lavender Pit being leached today. The Lavender Pit Leach Dump Stripping for the Lavender Pit was started in 1951, with mining operations on stream in 1954 and continuing to the present. All material removed from the pit has been classified as waste, leach material, milling ore, or direct smelting ore, depending upon grade and degree of oxidation. Lavender Pit leach material has been stockpiled in a single dump, called No. 7 Dump. This dump covers an area of approximately 135 acres and average about 300 feet in height. The dump has been deposited over a period of 20 years by truck haulage and contains several layers, each of which has a permeable boulder layer at the bottom and a compacted layer at the top. Leaching of Lavender Pit material was started in 1956 and has proceeded simultaneously with dump construction. Former leach pond areas and haulage surfaces have been ripped with D-9 tractors before deposition of succeeding layers of ore.

Jan 1, 1972

By John J. Rhodes

I welcome this opportunity to give a Congressman's birdseye view of a subject which I believe holds great potential for the future in helping meet the needs of people, with minimal adverse impact on the environment. All mankind, not just the people in this great nation, faces the need for additional usable space. In some parts of the United States the problem arises from rapid urbanization of the surface and little utilization of the subsurface. Everywhere there is an increasing problem of insufficient space arising out of the increasing population crush and growing demands for open space, housing, water, transportation, communication, and social service. You are the technicians to whom we look for assistance in finding answers. We look to you also to provide guidance for broad policy decisions concerning underground space. I prepared for a career practicing law, but since 1952 I have been a member of the House of Representatives. In this latter capacity I deal with programs designed to help solve all kinds of problems. But, naturally, I am especially interested in the water scarcity and other environmental problems of my home state of Arizona and the arid and semi-arid areas in the West. This North American Rapid Excavation and Tunneling Conference has as its theme: "Tomorrow's Tunneling Technology Today." I have a very great interest in this potential of our underground space resource. The Central Arizona Project now getting underway in my state will consist in part of tunnels and underground pipelines to convey life-sustaining water from the Colorado River to people and lands across Arizona to the Phoenix and Tucson areas.

Jan 1, 1997

By Germán Toledo

The closure of TSF represents a critical milestone in the life cycle of mining operations, requiring the integration of technical, environmental, and social dimensions to ensure long-term safety and sustainability. The GISTM introduces the concept of “safe closure” as a demonstrable technical condition in which there are no ongoing material risks to people or the environment. This status must be validated by an independent technical reviewer and formally approved by the Accountable Executive. This article presents a risk-based methodology to support the achievement of safe closure, aligned with the principles and requirements of the GISTM. The proposed approach emphasizes the need to identify, assess, and manage closure and post-closure risks progressively throughout all phases of the TSF life cycle: from site selection and design, through construction and operation, to closure implementation and long-term monitoring. The methodology integrates key elements of effective risk management, including comprehensive knowledge bases, consideration of climate change, credible failure modes, continuous monitoring, stakeholder engagement, and governance. The ALARP principle is applied to demonstrate that residual risks have been reduced to tolerable levels. By incorporating closure planning from the earliest stages and adopting a risk-based view throughout the entire life cycle, this methodology aims to support mining organizations in achieving a verifiable and responsible closure of tailings facilities, in line with international best practices such as those of ANCOLD and ICOLD. The proposed framework offers a practical contribution to strengthening the credibility, effectiveness, and sustainability of tailings closure processes.

Feb 22, 2026

By Doug Harding

The 3.5 km long Ashbridges Bay Outfall in Toronto, Ontario, Canada was a challenging drive set below Lake Ontario. After a remote machine acceptance due to the global pandemic, an 8 m diameter Single Shield machine launched in March 2021 from an 85 m deep shaft and began its bore in shale with limestone, siltstone and sandstone. During excavation, the TBM and its crew bored a city-wide record of 30 rings in one day, or 47 m of advance. This paper will cover the unique project, from TBM acceptance through to launch, tunneling in difficult conditions, and completion in 2022.

Jun 13, 2023

By B. J. Arnold

Coal froth flotation cells typically receive little attention in coal preparation plants. They process only a small portion of the total coal feed (perhaps 5-1 0% of the total plant feed in the United States), they are viewed as a way to take the load off the refuse thickener, and their operation is not well-understood by cleaning plant operators. Operating parameters are set based on the equipment supplier information, and reagent dosages are set at the recommendation of the latest chemical vendor. The cells then operate day in and day out, recovering coal and producing a product that may not meet ash or sulfur specifications or that may be the wrong percent solids for downstream dewatering operations. If improvements can be made to this circuit, then the whole plant will benefit. Paying attention to rate and residence time and the wealth of data from the literature or from a series of targeted laboratory tests can give operators the key to improving the performance of froth flotation cells AND overall plant performance. This paper provides an overview of froth flotation rate and residence time data and gives practical suggestions for specifying and using laboratory tests to improve froth flotation performance. Suggestions for improving froth cell performance are also given based on available literature data.

Jan 1, 1999

By Leo G. Martin, Richard G. Sherman

Recent sewer construction in downtown New Haven, CT required avoiding open trench methods because of near surface utilities and traffic congestion. The .73 km long alignment is in sands with the water table at the tunnel's springline. The designers felt the situation was ideal for an EPB machine; however, the tunneling method was left to the Contractor. The winning bid surprised everyone. The tunnel is being excavated by hand using an open face shield with breasting boards. The review of the bids indicates hand mining was approximately 1/2 the bid price of TBMs. Currently, excavation rates average 14 m/day with no excessive settlements.

Jan 1, 1993

By L. S. Harris

The application of briquetting in various chemical, mineral, mining and metallurgical processes has been rapidly increasing in the past two decades. This is, in part, due to the development of new, more economical and higher performance briquetting equipment. Some of these developments, which have reduced the operating and maintenance costs,, include anti-friction bearings, hydraulically applied pressure enclosed and sealed gearing and bearings, tapered predensification feed screws, water cooling and materials of construction capable of operating at temperatures up to 18000F, and control systems capable of maintaining optimum briquette quality control. The briquets can be formed into almost any desired size and shape, To date, with present rotary briquetting presses in the 25 to 500 ton force range, briquets from 1/4" to 6" length are presently being used, some of which are illustrated in Figure No. 1. In force fed rotary briquet machines, these shapes are produced by feeding the material in between a pair of counter rotating rolls, as illustrated in Figure No. 2. The rolls have forming dies indented into their circumferential surface, as illustrated in Figure No. 3.

Jan 1, 1973

By S. S. Peng

Since the introduction of shield supports in 1975, safety and production in U.S. longwall faces have improved considerably. Many faces had a daily production of up to 8,000-10,000 tons and productivity reached 600 tons per man-shift. But a longwall face requires expensive equipment which slows down the growth rate of the percentage of longwall production. Among the equipment cost the shield support accounts for 50-60%, a very large proportion. Therefore, it will have a large impact on the growth of longwall mining in the U.S. to reduce the support cost (1).

Jan 1, 1988

By Robert H. Merrill

In 1960, the Kennecott Copper Corp. and the U.S. Bureau of Mines entered into a joint research program to determine the changes in stress, strain, and displacement created by changes in slope angles. The field site was the Kimbley Pit, located near Ely, Nevada; the supporting laboratory investigations were made at the Bureau's Denver Mining Research Center. Following a study to determine the rock stresses in the mining district, the strike and dip of geologic defects (fractures) in the rock, and the laboratory-determined strength of the rock, a new slope angle and pit configuration was selected, and instruments were installed to measure changes in stress, strain, displacement, microseismic noise rate, and sonic velocities at several points in the west wall of the pit. Between February and November 1966, the west slope was changed from an average angle of 45° to a new slope angle that started at 45° on the south wall, gradually increased to 57 ½ at the center of the west wall, and to 61° on the north wall. The pit was deepened from about 500 feet to about 550 feet. About 2.55 million tons of waste and ore were removed by stripping and mining.

Jan 1, 1968