Search Documents

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By Devraj Sharma

This paper presents technical issues in the design and management of a retorted oil shale disposal site. Major physical and geochemical mechanisms which affect the disposal are: heat transport, moisture migration, chemical species transport, auto-ignition, and mechanical behavior alterations of the retorted oil shale pile. The interaction of these mechanisms and their relative magnitude will affect the environmental behavior of the pile. The paper discusses the coupling between the mechanisms, presents a framework to quantify the processes by laboratory and field measurements, and in addition discusses the use of mathematical models to provide quantitative predictions.

Jan 1, 1981

By Bruce K. Cantrell

As part of a continuing study of diesel exhaust aerosol characteristics, the Bureau of Mines has applied Chemical Mass Balance (CMB) model source apportionment analysis to evaluate a size selective sampling method for determining the separate diesel exhaust and coal dust aerosol concentrations in a diesel equipped coal mine. Size selective sampling was used under the premise that diesel exhaust aerosol dominates the submicrometer aerosol size range, while most of the mineral dust aerosol is greater than 1 m. A micro-orifice, uniform deposit impactor (MOUDI) was used as the size selective sampling method. Concurrent samples of mine aerosol were collected using a dichotomous, respirable aerosol sampler. This sampler separated the fine and coarse size portions of its sample at 0.7 m. Trace element concentrations for in-mine aerosol sources and the dichotomous samples used by the CMB model were measured using Instrumental Neutron Activation Analysis. The CMB analysis, applied to both the fine and coarse fractions of the respirable mine aerosol, yielded the mass concentration contributed to each by diesel exhaust and mineral dust aerosol sources. The MOUDI size distribution data were analyzed using nonlinear regression to parameterize the fine and coarse fractions of the sampled aerosol and to estimate the contributions to each fraction from both coal dust and diesel aero- sol sources. For the diesel mine visited, analysis of the MOUDI samples yielded a value for the fraction of the fine aerosol attributable to coal dust of 15[]7% fine fraction coal from analysis of the MOUDI samples versus 25[]4% from the CMB analysis. The remainder of the fine aerosol in the mine was diesel exhaust aerosol. CMB analysis confirms the original premise for such sampling. After correcting for the presence of coal dust in the fine aerosol fraction, analysis of the MOUDI size distributions yielded estimates of respirable mineral and diesel exhaust aerosol concentrations that were accurate to with-in 10% of values determined by the CMB apportionment.

Jan 1, 1987

By K. P. Unrug, E. Thompson, S. Nandy

The method of coal pillar design involves primarily two aspects: the geometry of the pillar and the strength of the coal. However, the strength of the coal has to be emphasized with respect to the entire pillar dimension rather than isolated strength values of coal samples taken and measured from different locations. As of now, the presently applied pillar design systems do not specify clearly what the coal sample strength really represents. The intention of this paper is to introduce the concept of seam strength as opposed to the current practice of using coal strength as a prime design criteria in the formulation of pillar calculations. Seams are most often composed of multiple layers of coal, partings, and bone in various configurations, changing within the vertical section of the seam even in relatively close locations. The difference in strength between the weakest and strongest component of the coal seam could be as much as five times or more. An experimental approach based on multiple uniaxial compressive strength tests performed on coal samples from the Coalburg and Warfield seams from eastern Kentucky was undertaken. Analysis of the results led to the conclusion that for pillar dimension calculations, both the weighted mean of the seam strength and the strength of the weakest stratum should be considered, rather than the relatively vague aspect of coal strength. The design of pillar dimensions based on the aforemen¬tioned criteria should assure a more realistic design performance.

Jan 1, 1987

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By Donald E. Dickie

At Sifto Canada's Goderich salt mine near Goderich, Ontario, the stress control method of mining was introduced to overcome increasing roof failure problems. After successful testing, the conventional room-and-pillar mining method was converted entirely to the stress control method. This conversion has successfully stabilized the ground, increasing the extracton ratio from 38% to 50%. At the same time, it reduced the ground control and rehabilitation cost by more than 80%. The success of the conversion is due to the quantitative technique of mine analysis that was developed to ensure that the conversion was safe and reliable. A finite element model of the ground was constructed to predict and validate the safety of the stress controlled mine opening. A system of in situ stress-property measurement instruments was developed to obtain input data for the computer model as well as to evaluate its output quantitatively with regard to time and location. History of roof problems Severe roof safety problems have been encountered at Goderich Mine since it opened in 1959. These problems continued into the 1980s. Following excavation, the roof strata started to deteriorate by slabbing. Even after roof rehabilitation, deterioration continued to progressively higher roof elevations, requiring repeated rehabilitation. The operational impact of these roof failures was severe, ranging from a considerable safety hazard to major production interruptions.

Jan 1, 1993

The following list is a representative sample of the types of software available to the mining industry. For additional information concerning software packages for your minicomputer, contact equipment manufacturers or software suppliers.

Jan 11, 1981

By R. W. Smith, Z. Sadowski

INTRODUCTION Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of contaminant metal ions and other chemicals on the flotation. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances, cations such as Ca2+, Mg2+, Fe2+, and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions. Some adsorption (abstraction) experiments were also performed. Experimental materials and methods The barite used was a high-purity, naturally occur¬ring mineral sample (Kings Creek, SC). The material was ground in a porcelain mill and a fine fraction (mean particle size 11.49 µm) separated out by air elutriation. The mean size was determined by an aqueous sedimentation method using a CAHN electro-balance. In the method, an 0.6-g sample of the barite was dispersed in 450 cm3 of pH 7 water containing 0.01 g of sodium tripolyphosphate. The mean particle size was denoted X0. The stability of the barite suspensions was determined by a comparison of the mean size of the investigated barite suspension aggregations with the mean size of barite powder determined in the presence of sodium tripolyphosphate. The mean sizes (X) of the barite aggregations were determined using the same amount of water and barite sample as in the measurements of dispersed barite particle size but without the presence of polyphosphate. The ratio X/Xo is thus a measure of the stability of a suspension (the greater the ratio, the less stable the suspension). The adsorption (abstraction) experiments were carried out in polyethylene bottles containing 1 g of barite powder in 200 mL of solution. The solids were added to a solution containing a known concentration of metal chloride salts (AlCl3, FeCl2, MgCl2, and CaCl2) . The pH was controlled by both HCl and NaOH addition. The suspensions were agitated in a shaker for three hours. The final ion concentrations in solution were determined by atomic absorption analysis. The electrokinetic measurements were made using a Komline-Sanderson Zeta Reader in a conventional manner. All experiments were carried out in the presence of 1.0x10-3 k.mol/m3 NaClO4. Experimental results Figure 1 shows the zeta potential of barite particles as a function of pH in the presence of iron(II). The

Jan 1, 1988

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

By Richard P. Killmeyer

In 1985 the Pittsburgh Energy Technology Center (PETC) of the U.S. Department of Energy (DOE) conducted a study to evaluate the emerging selective agglomeration processes (Killmeyer, 1985). This paper covers a recent similar study evaluating an associated technology, the emerging advanced froth flotation processes. This study has goals similar to those of the 1985 study: to evaluate the emerging froth flotation technologies collectively and determine how far they have progressed in their ability to clean ultrafine coal, and to assess the differences among the participants. The major concern again in this study was not the level of development, nor the economics of each individual process but only the current technical performance.

Jan 1, 1989

By John R. Keith

Keith, John R. 1968. Relationships of lead and zinc contents of trees and soils, Upper Mississippi Valley District. Preprint, Fall 1968 Meeting, Soc. Mining Engineers of AIME. Lead and zinc contents of elm, maple, and oak trees and of soils in which the trees grew were determined in samples from the Upper Mississippi Valley mining district, and from an area outside but contiguous to the district. The lead and zinc analyses of plant materials served to differentiate the mineralized and non-mineralized areas. Stems contained about two times as much lead and about 2-5 times as much zinc as did leaves taken from the same stems. Lead and zinc analyses of all soil horizons could be used to differentiate between the two areas. Soils at most sample sites in the mineralized district seemed to be more reliable than plants for geochemical prospecting and are a more practical sampling medium. Soil samples from areas with thick loess cover, however, failed to indicate the presence of mineralized bodies whereas tree samples from the same sites contained anomalous amounts of lead and zinc. It is suggested that in areas of thick loess cover plant samples could be used in prospecting for lead and zinc.

Jan 1, 1968

Copper cathode and Uranium Oxide production at WMC (Olympic Dam Corporation) Pty. Ltd. involves processing leach liquors through a copper solvent extraction plant followed by a uranium solvent extraction plant. This paper discusses the processing problems, metallurgical testwork and circuit changes made due to contamination of amine in the oxime circuit and vice versa.

Jan 1, 1996

By V. Enns, E. Soprovich, J. H. G. Laflamme

A mineralogical and geochemical characterization study was carried out on arsenic-bearing Ketza mine tailings to complement a column extraction test program with the purpose of assessing the potential of arsenic mobilization from the tailings. Two types of tailings samples (i.e., exposed tailings from the impoundment area and water covered tailings samples) were subjected to column tests under standing water cover and with no water cover but weekly flow-through flushing. The tailings have a uniform size distribution. The samples are characterized by high Fe2O3 (44.0 to 68.2 %) and As (3.7 to 4.4w%) concentrations. Ferric hydroxides are the dominant species that are mostly amorphous or cryptocrystalline. Arsenopyrite, scorodite, an Fe-Ca arsenate hydrate phase, an Fe-Bi-As phase and ferric hydroxides are the arsenic-bearing minerals. Arsenic is essentially contained in Ca-As goethite, Fe-Ca arsenate hydrate phase and scorodite. Goethite, although containing low levels of arsenic, could be a significant arsenic-bearing phase because of its high abundance. There does not appear to be any significant chemical or mineralogical difference between the original exposed tailings and the material left underwater with no flow-through for over a year. There are differences in terms of CaO, Fe2O3, SiO,, As, goethite, scorodite, calcite and dolomite concentrations between the exposed tailings and the column material after undergoing approximately two-year flow-through and aggressive leach tests. These differences are likely to be resulting from a combination of different column test conditions and sampling or heterogeneity of the material.

Jan 1, 1998

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By Laurindo De Salles Leal Filho

Microflotation tests with sodium oleate, in alkaline pH, were performed with apatite and some silicates (phlogopite, quartz, and chlorite) that commonly occur in Brazilian phosphate ores. Further flotation tests were carried out with selected ores containing the same silicates as important gangue minerals. The results showed that apatite recovery is highly affected by competition with silicate minerals, probably activated by calcium ions dissolved in flotation pulp. Inorganic chemical species (sodium tripolyphosphate, sodium carbonate/ bicarbonate, and carbon dioxide) that could act as water softeners were used as modifier agents. They proved to be capable of improving flotation recovery and selectivity.

Jan 1, 1999

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

In 1989, United States mine production of barite decreased 13% while world mine production decreased by 8.6%, according to the US Bureau of Mines. Consumption, sold or used by grinding plants, decreased by 21.2%. And imports decreased by 12.8%. The value of domestically produced barite, fob mine, increased 17.4%, according to the Bureau. The declared value cif US port of all imported crude barite during 1989 increased from $38.10/t ($34.56 per st) in 1988 to $40.27/t($36.54 per st). Nevada continued to be the leading producer of barite with 77% of the total, followed by Georgia and Missouri. The Bureau of Mines estimates 75% of the domestic mine production was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass, or as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the nonoilfield sector. Of the total consumption used by grinding plants and chemical manufacturers, it is estimated that 80% was used in drilling fluids. The other 20% was used in the non-oilfield sector, including barium chemicals and fillers in paper, plastics, and glass. The tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1989. The average number of rotary rigs operating was 869, 7.2% less than the average of 936 in 1988. Crude barite imports were down 12.8% from 1988. Imports accounted for 73.8% of the barite consumed (apparent) in the US. China continued to be the leading exporter of crude barite ore to the United States with 63% of total crude ore imports. India followed with 27.4%, Peru 4.3%, Chile 2.9%, and Canada and Mexico, each with 1.1 %. About 97% of the imported barite ore was used in the oilfield sector.

Jan 1, 1990

By N. Langsford

The Archaean Yilgam craton has been a major gold province since 1888 with production and reserves of about 4700 tonnes. Production in 1994 was about 135 tonnes. The largest deposit, the famous Kalgoorlie Golden Mile, contains about 2000 tonnes of gold. About 40 deposits containing more than 35 tonnes (1Moz) of gold has been discovered so far in the Yilgarn. Most of the craton has deep weathering profiles inherited from previous tropical climatic conditions, modified by subsequent arid conditions. A mantle of transported material covers much of the variably stripped weathering profiles. Resolving the geology of the volcanic-sedimentary units (greenstones) and the structures that host the gold mineralization relies heavily on aeromagnetics and shallow drilling.

Jan 1, 1995