Search Documents

By R. R. Klimpel

This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: 1) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.

Jan 1, 1996

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By İsmail İnce

The purpose of this study is to investigate the index-mechanical properties of igneous rocks by using the electrical resistivity method. Electrical resistivity, index (P-wave velocity, dry density, and porosity), and uniaxial compressive strength values of 48 different igneous rock samples were measured in the laboratory. Simple regression analysis was performed between index-mechanical properties and electrical resistivity values. Strong exponential and logarithmic correlations were found between electrical resistivity and the index-mechanical properties of the igneous rock samples.

Jan 21, 2022

By P. E. Snoek, R. L. Gandhi, C. S. Miller

Slurry operations are an integral part of mineral processing. There is therefore reason to consider using slurry pipelines for long distance mineral transportation. This paper reviews the current state-of-the art of such systems and, in particular, the design factors which must be addressed. It also discusses the selection of major components such as pipe, pumps, valves and storage facilities. Finally, the major steps required to determine the economic feasibility of a slurry system are listed and the major advantages and disadvantages of slurry pipelines compared with other forms of land transport are summarized. SLURRY PIPELINES: GENERAL OVERVIEW Minerals Transported Long distance slurry pipelines have been successfully used for transporting coal, iron concentrate, copper concentrate, limestone and phosphate. Additionally, several tailings disposal pipelines of considerable size and length have been built, but these generally are not categorized as long distance commercial mineral transportation systems. Table 1 lists selected examples of commercial slurry pipelines.

Jan 1, 1986

By J. Kemeny, B. Norton, T. W. BoBo

Digital image analysis systems to quantify particle size of crushed materials have successfully been applied in large-scale mining operations throughout the world. Particle size measurement at various crushing and sieving stages, especially in aggregate production, will facilitate the industry’s desire and need to achieve higher levels of process control and automation. This paper will 1) summarize applications of digital image analysis in the industrial minerals industries and introduce the Split-Online technology; 2) detail an actual recent test application of digital image analysis that ultimately lead to the installation of an automatic, non-invasive particle size distribution monitoring system; 3) document how this information is being applied: and 4) summarize the new Split-Online Aggregates Module now available.

Jan 1, 2004

By R. L. Pozzo

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying the Faraday's Law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a nonmagnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-electrode system involving pyrrhotite, pyrite and grinding media was also investigated as a first step towards elucidating the nature of interactions that occur in the grinding of complex sulfide ores.

Jan 1, 1987

By Jaroslaw Drelich

This report briefly reviews the measurements and interpretation of adhesion forces measured between microscopic probes and substrates having micro- and nanoscaled roughness characteristics that were recently conducted at Michigan Tech using atomic force microscopy. The laboratory study concentrated on both rigid and deformable materials, with the probes larger than the size of roughness features of interacting surfaces. For such systems, a detailed surface characterization in terms of roughness parameters, asperity size and shape, and spacing between asperities, as well as analysis of deformation of materials is required. Analysis of the experimental data can be done with theoretical models, which are suitable for rough surfaces and therefore allows to normalize the measured forces. Alternatively, loading of the probe during adhesion force measurements can be managed properly to control deformations of the nano-scaled surface irregularities. Controlling the deformation reduces and even eliminates the effects of nano-roughness on the probesubstrate contact area, promoting conditions described by the contact mechanics models for the sphere-smooth substrate system.

Jan 1, 2005

By S. Kelebek, G. W. Smith

Four samples of galena, each prepared differently, dry ground chalcopvrite and real gar have shown various quantities of liberated sulfur corresponding up to nine equivalent monolavers on their surfaces as determined by the solvent extraction/UV analysis of sulfur using ethanol. The pretreatment of a dry ground galena sample with acidified ammonium chloride or neutral, saturated sodium chloride solutions rendered the mineral readily floatable. The collectorless floatabilities of galena pretreated with the former solution and of drv ground chalcopvrite have been evaluated in reference to the natural floatability of sulfur using the critical surface tension of floatability approach with aqueous methanol solutions. It is shown that the amount of sulfur- on these samples can be correlated with their flotation rate, which was found to he first order within the critical surface tension range. The larger the concentration of surface sulfur, the faster the sulfide mineral floats, thus, the greater its flotation rate constant.

Jan 1, 1990

By Fritz Kleiner, Walter Meintrup

On Nov. 4, 1981 A/S Sydvaranger's 1-kt/h (1,100-stph) wet-process, iron ore ball mill completed its first four months of uninterrupted, full-load operation in Kirkenes, Norway. This 6.5-m-diam (21-ft-diam) mill is driven by a gearless ring or wraparound 8.1-MW (10,860-hp) motor at 13.1 rpm-a first of a kind in this segment of industry. This article examines reasons for selecting this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes the installation in Norway. History For almost a decade, good operating experiences have been gained with 28 gearless ring motor drives in the cement industry, driving 2.5 to 4-m-diam (8.2 to 13-ft-diam) tube mills with drive powers ranging from about 3-4 MW (4,000 - 8,000 hp). Why then did the mineral ore processing industry hesitate until 1980 to adopt this successful concept for similar applications on ball, semiautogenous, and autogenous mills? There are a number of good reasons in the eyes of conservative mill builders and operators, the most commonly cited ones are: • No operating experience in this segment of specialized industry. • More severe environmental conditions in the wet ore grinding process. • An indifferent attitude of mill builders and electric motor manufacturers towards new drive technologies. • Limited confidence in solid-state power supply systems, such as frequency converters of the required size. There have been and still are numerous problems associated with low-speed geared mill drives of any kind, especially with individual motor/gear sizes approaching or exceeding about 4 MW (5,360 hp). Every mill builder knows about them, but operators learn to accept them as inevitable. The Decision to Change Three things combined to break this technological stalemate: the courage and progressive spirit of one major iron ore processor in Scandinavia, the cooperation of three experienced manufacturers, and an unusual application problem that could not be solved by any conventional approach. The last factor was surely the decisive one, but the first one does not come as a surprise either. The Swedes near Kiruna and the Norwegians around Kirkenes are experienced ore miners and processors, and much credit goes to them for technological breakthroughs in the industry. At A/S Sydvaranger in Kirkenes, above the Polar circle at about the latitude of Alaska's northern tip, the existing grinding facilities, with a total of 14 100 to 240-t/h (110 to 264-stph) ball mills, can not be expanded. Nevertheless, to increase mill throughput, only installing a larger mill in place of an existing smaller one was a practical alternative. For this replacement, the owners set requirements that seemed impossible to meet: • The old 100-t/h (110-stph) ball mill should be replaced with a new ball mill with 10 times the rated throughput, without significantly impairing the operation of the remaining mills, and without significantly changing the mill building. • The new mill should have a variable-speed drive to ultimately optimize the grinding process by means of a closed-loop process¬computer-controlled grinding cycle, and to minimize the specific energy consumption. • Availability, efficiency, and life expectancy of all new components must be higher than those being replaced. • Inrush-current and harmonic loads on the rather weak electric supply line must be minimized to ensure safe plant operation. All old ball mills at A/S Sydvaranger are the geared type, using single synchronous and wound-rotor, slow-speed motors with ring-and-pinion gears. Operators are familiar with the limitations and problems associated with such drives, and they are aware that the following items become major concerns when drive powers are drastically increased: • Gears are subject to wear and tear, require frequent maintenance, and eventual replacement of major parts. • Gears are sensitive to misalignment, overload, and thermal distortion, limiting their useful life. • On dual or quadruple drives, load-sharing and torque oscillations between motors can be a major reason for concern. • At these speeds, ring-and-pinion gears reach their torque transmission capabilities altogether at around 4 MW (5,360 hp) per motor/pinion. To obtain the desired variable-speed performance of the new drive, the only practical and economical conventional solution would have been a frequency-controlled, low- or medium-speed dual motor drive with about 8 MW (10,720 hp) of power. This, however, was not feasible because of limited floor space. Therefore, bids were solicited for the alternative drive method, the gearless ring motor. General Considerations Why are such large mills considered? After all, one could avoid all the problems by simply staying with smaller mill unit sizes. Under competitive pressures of free markets, however, grinding efficiencies and specific energy consumption become key factors in selecting new equipment. Specific energy consumption of ball mills decreases with increas-

Jan 9, 1982

By Zhongran Dai, Nan Hu, Jianhong Ma, Hui Zhang, Zhihua Zhong, Han Zhou, Feng Li, Yonggen Qiu, Yang Ding, Yingchun Yang, Dexin Ding

In the traditional chlorination roasting-water leaching-solvent extraction process for the extraction of rubidium-bearing ore, Rb leaching from the ore and calcium removing from the leachate are conducted separately, and this results in the complicated process and high energy consumption. In order to integrate the Rb leaching and calcium removing processes, Rb-bearing polymetallic ore was firstly treated by chlorination roasting, it was then leached in a micro-reactor with raffinate, and the calcium ions in the leachate were removed in the reactor as carbonate precipitates by passing CO2 at certain pressure into the reactor. The effects of raffinate alkalinity, CO2 pressure, and CO2 reaction time on Rb leaching rate and calcium removing rate were investigated. The experimental results show that when Rb-bearing polymetallic ore was leached for 90 min by stirring with raffinate with 1.125-mol/L alkalinity, and the pulp was made to react with CO2 at 0.8 MPa for 15 min, the Rb leaching rate and calcium removing rate amounted to 92% and 98.2%, respectively. This integrated process including Rb leaching from Rb-bearing polymetallic ore and calcium removing from leachate could simplify the process for the extraction of Rb-bearing ore and increase its economic benefits.

Sep 27, 2023

By K. Tokutake

Kobe Steel, Ltd. improved the quality of iron ore pellets for blast furnace burdens when it enlarged its blast furnaces. However. there still remained room to increase reducibility at high temperatures for better blast furnace operation. In particular, it was still necessary to lessen the reduction retardation above 1200?C. In the last few years, by employing iron ore and additives of optimum size structure, large pore pellets with a high porosity have been obtained. By using this method. Kobe Steel. Ltd. has accomplished the technology to produce pellets with remarkably high reducibility.

Jan 1, 1989

By Fritz Eder, Rick Hendrickson

The quantities requires decisions growing demand for large of oxygen by gold smelters today that economic and operational be made regarding their selection providing electrical power, water, communications, sewage facilities and access roads. Liquid storage and supply system is of the system. decisions most appropriate oxygen supply Key factors affecting such are discussed in the following.

Jan 1, 1990

By Thomas E. Weyand, Wolfgang Baum

PMET is engaged in the development of reuse operations for process wastes from the natural resources industry. Most of the current remediation practices with mining wastes are concentrated on stabilization techniques. Once stabilized, valuable resources are no longer readily available for recovery and reuse. Additionally, stabilized materials, unless protected from weathering influences, pose lingering liability for the generator.

Jan 1, 1992

The dissolution behavior of gold and copper from their elemental states and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc electrode. The anodic and cathodic reactions were studied separately and the resulting polarization curves were combined to examine the overall dissolution reactions. The dissolution rate of pure gold in the aerated cyanide solutions was inhibited by the anodic passivation on the gold surface, while the dissolution rate of pure copper was found to be mass-transfer-controlled. On the other hand, the dissolution of gold and copper from the alloys was partially controlled by electrochemical reaction and largely by mass transfer.

Jan 1, 1994

By R. O. Y. Breese

The term "diatomite" implies the nearly pure sedimentary accumulation of diatoms. Sedimentary and chemical purity, low density, inertness, intricate fine structure, high brightness and other properties give the diatom and diatomite unique industrial usefulness and commercial value in high value functional filler and specialty filter aid products. Although diatomite deposits occur commonly throughout the world in Miocene and younger marine and lacustrine sediments, deposits that contain significant reserves of crude suitable for these quality sensitive markets are uncommon. U.S. production is centered on exceptional deposits located in Arizona, Nevada, Oregon, Washington and California. Evaluation of deposits requires understanding of geology, mining, production and end use. As crude quality in deposits varies within and between strata, ore suitable for quality sensitive end uses must be identified through sampling and evaluation programs tailored to permit recognition of critical variations.

Jan 1, 1989

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Red mud has been reported as a potential resource for lithium. To investigate the leaching behavior of lithium, a lithium-rich red mud was neutralized with hydrochloric or oxalic acid and then leached with acetic acid. When red mud was neutralized using dilute hydrochloric acid, about 58 to 60 percent of lithium was leached with 25 percent acetic acid at 95 °C for 60 min, while more than 95 percent of sodium and 85 percent of calcium were dissolved in the leachate solution. When oxalic acid was used to neutralize red mud prior to acetic acid leaching, lower lithium leaching efficiencies of about 42 to 47 percent were observed. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the same conditions. In this study, 25 percent (v/v) of acetic acid at 85 °C for 60 min was demonstrated to be the optimum conditions for lithium extraction from oxalic acid-neutralized red mud using acetic acid. The results are useful and of interest for lithium recovery and purification from red mud.

By M. Argiantopoulou

In today?s mining environment, improving production, performance, productivity and profitability is crucial. Production, ancillary, plant and shipping equipment need to be monitored and controlled by online systems delivering production statistics and real-time information to everyone involved, including equipment operators. Traditional systems currently in use today, operate in an iterative mode constantly switching between scheduling and execution. However, the real world tends to change in ways that invalidate such advance schedules. Agent based computing has been hailed as the most significant breakthrough in software development and the new revolution in software. Agent systems are being used in an increasingly wide variety of applications, including complex mission critical systems such as Air Traffic Control. This paper presents the possible ways that multi-agent systems can be applied to mine production and rehabilitation scheduling problems with focus on real time fleet management, plant and equipment performance monitoring, downtime and delay reporting, stockpile management, personnel and equipment tracking and product distribution and transportation.

Jan 1, 2006

By R. Hogg

The factors which control the dewatering of fine coal by gravity/centrifugal drainage and by gas displacement (vacuum/hyperbaric filtration) are evaluated. A generalized model is presented and used to describe dewatering kinetics and to establish dewatering limits. Applications to the design of dewatering systems for fine coal dewatering are discussed.

Jan 1, 1995

By N. D. Cristescu

An analysis of the interaction between a creeping rock and a yieldable lining is presented. The following cases are considered: an elastic lining, a lining made of circular shaft rings that may slide at their joints, a lining made of circular reinforced concrete panels with wooden compressible strips inserted between the longitudinal joints and a yieldable support that has a compressible broken-rock stratum between the support and plane rock. By formulating a mathematical model for the rock-lining interaction, one can optimize the sequence of excavation-lining application. To keep costs to a minimum, one can also choose the most appropriate lining for the corresponding rheological properties of the rock.

Jan 1, 1997

By G. Roy, C. B. Pettersson, S. Nandagiri, D. J. Ivor-Smith

The Coastal Water Authority's 2,740mm/2,590mm (108 in./102 in.) pipeline, known as the Northwest Lateral Project, will transport raw water from an existing pipeline over 14.3 km (8.9 miles) to the City of Houston's East Water Purification Plant. The new pipeline crosses under Houston Ship Channel and Greens Bayou in tunnels at approximately 30.5m (100 feet) and 25.9m (85 feet) depths, which present unique experiences in tunneling under open bodies of water in the Gulf Coast's soft ground conditions. An earth pressure balance TBM is being used for the deep tunnel sections where the ground demonstrates high overload factors and variable conditions ranging from clays to silty sands. This paper discusses the design approach for the tunnels and shafts, ground conditions, constructability, and selection of the primary lining system.

Jan 1, 1989