Search Documents

By George D. Brunton

The past and present argillaceous rock studies for the U.S. National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several wide- spread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock.

Jan 1, 1981

By George Aul, Richard Ray

Short-hole horizontal degasification systems have been utilized in Island Creek's Virginia Division mines since 1986. These systems remove methane from the coal seam in advance of longwall mining. Without an in-seam methane drainage program, methane liberation rates from the longwall faces may exceed 0.47 cu m/s (1,000 cfrn), requiring 47 cu m/s (100,000 cfm) of air for adequate dilution capability. Optimization of the degas systems has enabled methane liberation levels and the associated ventilation requirements on the longwall faces to be reduced by 50 to 80 percent. Since the inception of the first degas system at the Virginia Pocahontas No. 6 Mine, Island Creek has developed an overall methane drainage program designed to maximize gas production and minimize ventilation requirements for methane dilution. Gas production from the degas systems is affected by four main design criteria: (1) hole location, (2) hole length and spacing, (3) collection system capacity, and (4) time available for drainage. Drilling equipment and materials for the gas collection system are selected to meet the necessary criteria while minimizing manpower requirements. Benefits gained from reducing methane liberation rates from the longwall faces are fourfold: (1) improved safety due to lower methane concentrations in the face area, (2) fewer production delays caused by excessive methane concentrations, (3) lower fan operating costs resulting from reduced air requirements, and (4) enhanced worker comfort resulting from lower air velocities and less dust generation.

Jan 1, 1991

By Karl Gugel, Dante Garcia, Peter Czel, Eduardo Nunez, Joshua Morales, Boris Sullcahuaman

Real-time operational excellence is achieved through the seamless integration of various components. Key aspects include precise instrumentation, real-time data collection, data analytics, and an efficient optimization platform. Additionally, to ensure success, the real-time optimization platform must be incorporated into the site’s internal process control system (Nunez, 2022). This paper provides an overview of practical lessons and best practices for autogenous (AG), semi-autogenous (SAG), and ball mill (BM) grinding. It highlights the implementation of advanced instrumentation, specifically vibration sensors on the rotating mill shell. The paper also delves into the application of advanced analytics necessary for generating new measurements that accurately represent real-time grinding activity in the mill. These Advanced Analytics Measurements (AAM) are compared with well-known grinding curves to determine the optimal grinding point. The discussion focuses on key industry opportunities using real-time mill shell vibration results to derive new correlations and optimize the grinding process.

Feb 1, 2025

By P. Arell, D. Folkes

This paper presents the basics of EPA’s Hazard Ranking System (HRS), which is used to evaluate sites for possible inclusion on the Superfund National Priorities List (NPL). The paper describes the surface water, ground water, air, and soil exposure pathways and how they are applied to mining sites. Key factors contributing to the site score include the likelihood of a release, waste characteristics, and the targets for each pathway. Waste volumes, definitions of landfills versus surface impoundments, and background concentrations are of particular importance to mining and smelting sites. Because of the presence of metals, large waste volumes, and observable releases, mining and smelting sites often receive high enough scores to be proposed for the NPL based on a single path-way. Neverthess, owners and operators can take steps to reduce the risk of being scored, and to reduce the potential for high scores.

Jan 1, 2004

By T. G. P. Vasquez

The elimination of metal ions from aqueous solutions by biosorption plays an important role in water pollution control. Heavy metals are hazardous to the aquatic ecosystem and pose possible human health risk. Beside the toxic and harmful effects to organisms living in water heavy metals also accumulate throughout the food chain and may affect human beings. Conventional methods for removing metals from aqueous solutions before they are disposed of include chemical precipitation and sludge separation, chemical oxidation or reduction, ion exchange, reverse osmosis, electrochemical treatment, and evaporation. Alternative processing methods are being considered more seriously. Sorption and/or complexation of dissolved metals species based on the chemical activity of biomass, known as biosorption, is the base of the new technology for metal removal and recovery. Different types of biomass (dead and alive) have been investigated for biosorption of heavy metals ions. In the present work, the cadmium biosorption capacity and bioflotation of Rhodococcus opacus were studied. The adsorption capacity of biomass was investigated by batch experiments, the influences of some variables like pH and ion concentration were evaluated and the experimental data obtained for each metal were evaluated and fitted using adsorption and kinetic models. The bioflotation process showed that R. opacus has excellent features as collector and foaming agent after metal biosorption. Around 90% of cadmium uptake by the biomass was achieved by bioflotation.

Jan 1, 2006

By Alexander Pomerantsev

In recent years, bucketwheel excavators have found wide application in open pit surface mining not only because of their large production capacities, but also because they easily lend themselves to automation. Krupp, Orenstein & Koppel, Buckau-Wolf, Mechanical Excavator, Lauchhammer, Manufacturers in Eastern Europe designed and installed many models of bucketwheel excavators that can excavate any type of materials, could be used in any climate conditions and for any type of technological schemes in open pit surface mining, (Photo I, II and III)

Jan 1, 1979

By Hector M. Valenzuela, Juan H. Rojas

This paper presents a strategic plan for automation, plant integration and process management being implemented at the Chuquicamata mining and metallurgical complex of Codelco-Chile. This five-year plan considers different levels of process control and plant integration, which include instrumentation and direct control, process models and supervisory control, plant information integration, and real time process and plant wide management. The conceptual solution developed defines an architecture for the overall system and the projects to be implemented by each production unit, as part of the proposed solution for the division wide process control, plant integration and real time process management. An estimate of the cost benefit relation of the plan is also given.

Jan 1, 1998

By D. G. Bosse

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing These are fairly well understood and provide the starting point for decisions Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X This additional major variable IS not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures

Jan 1, 1983

By X. K. Jiang

Pneumatic, triboelectrostatic processing of physical mixtures containing fine (-200 mesh) particulate may have significant application potential in the mining and energy industries. Such dry processing methods, especially for finely comminuted materials, have not been examined in as much detail as wet processing methods nor have been part of the training or education of mining and process engineers. We have examined fundamental and applied physical and engineering factors controlling triboelectrostatic beneficiation of fine-sized physical mixtures, one of which -combustion fly ash -has size, heterogeneity and mineral concentrations typical of those expected in mined minerals. The applicability of dry processing, however, cannot be readily evaluated because of the unavailability of standard procedures for process assessment.

Jan 1, 1999

By Keiichi Fujita, Michio Miyoshi, Hisashi Miyazaki

In the construction of "Hamacho" subway station (Tokyo Metropolitan Rapid Transit), in order to minimize ground surface settlement, the pipe-roof method was employed as an auxiliary measure when removing the portion between two parallel shield tunnels to form one large tunnel for the station. 14 steel pipes (dia.1,219.2mm, length 75m) were driven in horizontally so as to cover tunnels and support heavy and extremely soft covering soil and surface structures. Procedures of temporary supporting, excavation under compressed air, reinforcing, concreting, etc., and some comparisons with conventional methods are described.

Jan 1, 1979

By Peter Mason, Chris Walker, Mike Costello

The Phase I electrowinning system at KCGM's Fimiston Operation utilised the well proven technology of electrowinning precious metal values onto steel wool followed by calcining and direct smelting to bullion. The above process, while reliable and successful, was to some extent labour intensive. The Williams Mine in Ontario, Canada had published conditions under which precious metal values are electrowon onto woven stainless steel and directly removed using high pressure sprays. The current paper describes the testwork which was carried out to check the applicability of the Williams criteria to KCGM eluates arising from the elution of highly loaded carbon from the calcine circuit and lowly loaded carbon from the float tails circuit. Information is also given on the commissioning and opera­tional experience which occurred.

Jan 1, 1996

By B. J. Scheiner

The presence of organic materials in gold ores cyanidation. The presence of organic materials interferes with gold extraction by The carbon contained in the ore has been shown to adsorb gold cyanide complex from solution. Removal of the carbon content by roasting or chemical oxidation prior to cyanidation results in gold extractions of 85 to 95 pct. This paper by the Bureau of Mines, U.S. Department of the Interior, discusses how the mineralogy of the carbonaceous gold ores affects gold recovery by cyanidation. It also discusses the advantages and disadvantages of roasting and chemical treatment to render the ore amenable to cyanidation.

Jan 1, 1987

By Charles G. Zink

Early anthracite "deep mining" methods, production, manpower. underground transportation, labor, safety and reserves are reviewed and compared to the present and to future requirements which must be met in order to economically win the fourteen million tons of untapped reserves and to keep the product competitive in the market place.

Jan 1, 1971

By Michael E. Mcllwain, Lee O. Nelson, Robert D. Rogers, James H. Wolfram

Examination of the economics and environmental consequences associated with phosphate fertilizer production documents the necessity for development of innovative production technologies. Evidence of phosphate ore's susceptibility to microbial alteration indicates that it will be an ideal candidate for industrial-scale bioseparation. There are at least two applications for the biosolu- bilization technology: (1) an industrial-scale bio- process similar to the presently used wet acid process and (2) production of small prills (bio- bead) containing unprocessed rock phosphate and the biological ingredients necessary to promote phosphate solubilization. At the present stage of development, the biobead technology is the preferred application. It is an energy-efficient "green" technology that will dramatically reduce the amount of solid waste and air emissions produced by the phosphate industry.

Jan 1, 1999

By Bruce C. Trent

The need for effectively evaluating the potential for surface subsidence due to under- ground mining has been widely documented. As the emphasis within the coal mining industry changes to reflect the increasing demand of this resource, the potential for damage due to differential surface subsidence will certainly become more acute. The present state-of-the-art of predicting ground motion due to underground excavations is, at best, primitive when one considers the immense complexity of possible geological inter- actions. For the most part predictions have been limited to empirical evaluations based upon earlier case histories. While the tools of the subsidence engineer are limited, they are important and serve to provide reasonable bounds for possible ground motion. As underground mining becomes more extensive, however, there will be many instances where excessive subsidence will be most undesirable and yet there may be few, if any, case histories similar to the operation in question.

Jan 1, 1982

By Bill Morgan

This paper discusses the economic zones of application for several different types of earthmoving equipment: dozers, wheel loaders in load-and-carry applications, wheel tractor scrapers, articulated trucks, rigid-frame trucks and wagons. Only the medium to large pieces of equipment were considered. From this chart (Figure 1), you can see the size range, in tons of carrying capacity, of Caterpillar equipment and the specific models analyzed.

Jan 1, 1994

By J. H. Meza Viveros

This paper describes some actual parameters and technologies used at Mexicana de Cobre Smelter, and the principal design parameters and new technologies which wiil be used with the smelter expansion project, in order to increase the production capacity of anode copper from 180 000 mtpy to 300 000 mtpy. Likewise its describe some parallel projects under construction also in the smelter plant.

Jan 1, 1997

By Mr. Peter J. Huck

Recent research has developed procedural control and geophysical test methods that can greatly enhance quality control in rock grouting. Confidence that design objectives will be made In construction requires that grout monitoring efforts be carefully designed and integrated into the overall project. Parameters that should be monitored are identified and documentation/review procedures that permit effective evaluation of the grouting effort are discussed.

Jan 1, 1980

By James M. King

Analytical models for transient groundwater phenomena, such as those of Theis, Cooper, and Jacob, are important but often limited tools for aquifer evaluation and drawdown prediction. Most were developed using simplifying assumptions which compromise their treatment of complex boundaries and most also contain functions that are mathematically complex and difficult to solve explicitly. Examples of such functions are the Bessel functions, the exponential integral, and similar well functions for leaky confined and water table aquifers. This paper describes the joint use of simple numerical techniques and numerical approximations of these functions to extend many analytical models beyond their conventional applications. The enhanced analytical methods represent many hydrologic problems more easily and realistically, permit a wider range of application, and often provide insight into the response of pumped groundwater systems without the need to resort to more complex numerical flow models. Use of the enhanced analytical methods usually requires the use of microcomputers due to the large number of computations. Examples presented here are the development and extension of type curves and the determination of drawdown distributions.

Jan 1, 1984

By M. H. Pettibone

During the past decade, the size of grin- ding mills has steadily increased. Mills 11 m in diameter with 9 mW motors have been installed with even larger units on the drawing board. The rising costs of energy and labor have spurred interest in improving efficiency while reducing capital investment and operating labor. Autogenous and semiautogenous grinding have experienced renewed interest as efforts to reduce operating and capital costs have increased.

Jan 1, 1981