Search Documents

By Carl-Henrik Knudsen, Rolf Tore Arnesen, Eigil R. Iversen

Recovery of iron and copper from acid mine drainage was studied in pilot scale at a continuous treatment plant at the mine site of the King's mine in Roeros, Norway. The average load on the plant was 1 m3/h. The process tested in this project is a three-step process consisting of: 1) Fe(OH)3 precipitation at pH 3.5, dewatering of iron sludge and transport to ferric chloride plant; 2) after filtration precipitation of residual metals at pH 9, concentration of metal sludge by flotation; 3) extraction of metals from the sludge with sulphuric acid followed by recovery of copper by electrolysis. The copper could be used for local production of different crafts, but this condition needs a further evaluation. The process economy at a full scale plant is evaluated.

Jan 1, 2000

By L. Harris

The gold mining and ore processing operations of Minera Yanacocha S.A. are 10cated in an area 4,000 meters above sea level in the Peruvian Andes same 600 km north of Lima and 20 km north of Cajamarca. The joint venture partners are Newmont Second Capital (USA); Compania Minera Condesa (Peril); Mine Or (France) and the IFC. Newmont manages the operation. The Yanacocha district comprises several areas with mineralization evidence. The first ore with minable reserves of 28 million tonnes of ore assaying about 1.4 gpt Au is called Carachugo and is being mined and treated at the rate of 14,000 tonnes of ore per day by open pit mining methods. ROM ore is dump leached and the gold recovered in a Merrill Crowe plant. The plant design incorporates some unusual considerations to overcome the problems of the high rainfall in this area and assure the protection of the environment.

Jan 1, 1994

By A. W. Mitchell

Mining of a bedded barite deposit exposed highly pyritic siliceous sediments which have weathered and degraded subsurface and surface waters. The ph, sulfate, and total dissolved solids are the most seriously affected parameters. Several solutions were tried and eventually horizontal holes were drilled into the mine wall to draw down the water table and decrease the movement of groundwater through oxidizing zones opened up by the mining operation. Areas of surface disturbance were capped with layers of soil, bentonite, and gravel to decrease the infiltration of water into the disturbed areas. These actions have begun to decrease sulfate and total dissolved solids concentrations and increase ph values.

Jan 1, 1987

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By K. Terhaar, K. Prisbrey

The objective was to determine operating protocols for a lead and silver column flotation cleaner, being considered for installation at Sunshine Mining & Refining Co.’s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause and effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feedgrade. The results were that xanthate, zinc sulfate, and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences were useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training, and provide a foundation for future on-line control.

Jan 1, 1999

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

By Andrew E. Nevin

The government of India convened a precedent-setting meeting in New Delhi on Nov. 12, 2001.The meeting brought together regulators and the mining industry in an attempt to fix the industry’s mine development problems in that country. More than 150people attended the all-day session. Ram Vilas Paswan, Minister of Coal and Mines, chaired the meeting. Ravi Shankar Prasad, Minister of State for Coal and Mines, was also present. The secretary of the Department of Mines and the Joint Secretaries and Additional Secretary also participated. The Department of Mines’ mandate is for economic growth: to get new mine development going and to make investment in mining attractive for both domestic and foreign-owned companies.

Jan 1, 2002

By F. Burat

Large reserves of feldspar ore exist in the Aegean region of Turkey. The main colored impurities in these ores are iron- and titanium-bearing minerals such as anatase, rutile, sphene and ilmenite. In this study, a potassium feldspar ore containing mainly quartz and coloring impurities was subjected to beneficiation tests involving magnetic separation and flotation, which were applied either separately or in combination. Bench-scale flotation experiments using cationic collectors G-TAP and Flotigam V-4343 and using HF and H2SO4 as modifiers were employed to separate feldspar from quartz and to remove part of the titanium impurities. The best results were achieved with a combination of high-intensity wet magnetic separation and flotation. A feldspar concentrate containing 16.28% Al2O3, 10.75% K2O, 2.84% Na2O, 69.97% SiO2 and 0.16% Fe2O3 was produced. A quartz concentrate containing 2.30% Al2O3, 0.48% K2O, 0.42% Na2O, 0.07% Fe2O3 and 96.20% SiO2 was also obtained

Jan 1, 2007

By S. H. Brown

In our work as health physicists*, we do a lot of public speaking and interaction with the public on issues related to development of uranium mining and milling (?uranium recovery?) in the US. Understandingly, the public has important concerns about this. Accordingly, this paper is presented in a ?question and answer? format in which we have tried to capture what are some of the most common concerns we hear from citizens and address them. We have attempted to do so based on the best scientific information we have, representing information well documented in peer-reviewed scientific literature and consensus positions from both national and international scientific standard setting bodies and related committees. We have included some of the more important of these scientifically-based references to support the information provided. Practical space limitations prevent completeness in this regard in some cases. Visit the Health Physics Society?s web site or feel free to contact me directly for additional references, information or detail ? Steve Brown. The health physicist?s primary objective is to manage the beneficial uses of ionizing radiation while protecting workers and the public from potential hazards. For more information on what a health physicist is and on the Health Physics Society, visit the Society?s web site at www.hps.org.

Feb 23, 2014

By Sidney A. Hiscock

INTRODUCTION Lead and zinc are today rightly regarded as sister metals. Historically, however, they differ markedly with lead being known and in general use as the metal since 3000 BC in several countries which at that time might have been described as mature economies. Zinc was not isolated and recognised as an industrial metal with distinct and valuable properties until about 1700-1800 AD (although it had, of course, been utilised as a constituent of brass for some 2000 years previously). c were well established as industrial metals by the beginning of the 20th century. The present paper briefly reviews the overall growth in world consumption* and changes in the three main areas which today represent the mature economies or industrialised areas, i. e. ,Europe, the United States and Japan. Trends in overall consumption are determined by the demands for the individual uses for lead and zinc. The changes in patterns of use in the industrialised areas - individually and collectively - and reasons for the changes are also considered. LONG TERM TRENDS - 1900-1984 The World Picture Since the beginning of the 20th century the world consumption of lead (3.9 million tonnes in 1984) has grown almost fourfold and that of zinc (4.7 million tonnes in 1984) is almost eleven times greater than it was in 1900. The long-term trend has been one of continuing expansion for both. metals although the pattern has been severely disturbed at certain periods, for example in the years immediately following the two world wars and at times of marked recessions in industrialised areas. Apart from such major setbacks, new levels of consumption have been established regularly every few years. Recently, however, consumption has not really grown and with only a slow and partial recovery in world industrial activity at present, there is no indication that the peak consumptions of 4.2 million tonnes of lead, set in 1979, and 4.8 million tonnes of zinc (1973) will be exceeded in the near future. The growth in world lead and zinc consumption since 1900 is shown in Figure 1 (which includes changes in copper and aluminium for comparison). Overall growth over the period 1900-1984 has been about two percent a year for lead and about three percent for zinc (annual growth for copper has also been about three percent). Increases in tonnage consumption and growth rates by decade for lead and zinc are summarised in Table I. However, the growth rates by decade sometimes conceal very large individual annual increases and decreases. For example, in 1975 lead consumption fell by 13 percent and zinc consumption by 22 percent compared to 1974. In 1976 consumption of lead and zinc rose by 12 percent and 18 percent respectively. The years when consumption 'landmarks' (ie one, two, three and four million tonnes) were first reached are shown on Table 2. Clearly, the pattern of shorter periods being required to attain each extra million tonnes of consumption was broken in the 1970's. The consumption of zinc overtook that of lead for the first time in 1940, and since 1946 has always been at a higher level. Trends in industrialised areas The two key industrialised areas at the beginning of the 20th century were Europe and the United States which between them accounted for some 95 percent of world lead consumption and 98 percent of zinc consumption. Figures 2 and 3 show the growth in lead and zinc consumption, and Figures 4 and 5 the percentage shares for each area since 1900. Europe has usually been the major user of lead except for some years in the 1920fs, most of the 40's and early 50's when consumption in the United States was larger. In 1900, Europe accounted for about 64 percent of world lead consumption and the United States just over 30 percent. Currently, Europe takes about 40 percent of world consumption and the

Jan 1, 1986

By Brent Duncan, Doug Harding, Bob Stier

The 73rd Street Tunnel Project is part of “The Tunnel and Reservoir Plan” (TARP)also known as the Deep Tunnel Project, and is located in the Village of Bedford Park, County of McCook, State of Illinois. The project consists of a ø 4.42 meter × 2,060 meter long (14´-6? bore, 6,760 foot)tunnel. The completed tunnel is used as a bypass tunnel for the McCook Cup Reservoir Project. The project was awarded to Affholder Inc. of St. Louis, in 2000. The paper describes the project in which a new, high-powered open gripper type main beam machine was used in which high advance rates have been achieved using conventional muck haulage techniques. Features of the project include the installation of rock support consisting of counter-sunk rock bolts that are required to be pull-tested for strength per project specifications. Installation and testing of the bolts are done during the boring cycle. Muck haulage was done by conventional muck car train and hoisting at the construction shaft. As the site layout did not include a tail tunnel, the trains needed to be shuttled at the shaft bottom. Even with the bolting requirements and the muck haulage without a tail tunnel, the Affholder site personnel still achieved high advance rates on the 73rd Street Project.

Jan 1, 2003

By S. Gallagher, A. Mayton

Introduction The mining industry has long been associated with a high incidence of low back disorders and pain (Klein et al. 1984, Leigh and Sheetz 1989, Brinckmann et al. 1998). It is believed that the higher incidence of these injuries among miners is the result of high exposures to postural demands, heavy manual work, and exposure to whole-body vibration (WBV). Recent work has indicated that miners involved with heavy lifting (especially in restricted spaces or on uneven ground) or who have been exposed to whole-body vibration in undamped seats experience noticeable changes in their spines that are consistent with degeneration of the intervetebral discs of the spine (Brinckmann et al. 1998). As will be described shortly, there is mounting evidence that disc degeneration plays a large role in the development of low back pain, particularly chronic back pain. Until fairly recently, medical doctors generally assumed that back pain was the result of muscle strain, ligament pain, or so-called “trigger points” (Bogduk, 1997). However, research supporting these mechanisms of pain has been very scant. When subjected to scientific scrutiny, none of these mechanisms has been shown to relate to back pain in a convincing manner. On the other hand, there are three mechanisms that have been shown to be highly associated with back pain in controlled scientific studies: sacroiliac pain (present in 13% of back pain sufferers) (Maigne et al. 1996), facet joint pain (present in 15 % of back pain sufferers) (Schwarzer et al 1994), and disc disruption and degeneration (present in 39% of chronic back pain sufferers) (Moneta et al. 1994). The latter mechanism, which bears the highest relationship to back pain that has been objectively demonstrated, will be the focus of this section. Scientists now believe they have a good idea how back pain may develop in cases involving disc disruption and degeneration (Bogduk 1997). As the spine experiences loading during lifting tasks or whole body vibration, the first structure to fail is called the vertebral endplate, which is a structure that attaches the disc of the spine to the vertebral body (Figure 1). The endplate typically experiences a fracture, which the body will attempt to heal by means of scar tissue. Unfortunately, this scar tissue impedes the flow of nutrition to the disc itself (discs are dependent on nutrition from the vertebral bones), and if the supply is reduced sufficiently, the disc will start to degenerate. As this degeneration process proceeds, fissures or tears in the fibers of the disc start to develop. If any of these tears is a grade 3 fissure (Figure 2), an inflammatory response occurs in the disc, which will lead to the well-known sensation of low back pain (Peng 2006).

Jan 1, 2007

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By R. Benito, J. Lopez, H. Gamarra

This article describes three practical applications of the Hill of Value (HoV) methodology within different stages of strategic planning for open-pit mining operations and projects. In the pursuit of optimal mine planning, this study establishes a comprehensive case study during the (i)design phase, by refining key parameters for efficient decisionmaking. (ii)production planning, where the HoV is used to define achievable production rates, enhancing operational effectiveness through a nuanced consideration of mining and processing capacities. (iii)Additionally, the study introduces a conceptual framework for orchestrating the optimal sequence of multiple pits during the planning phase, with a focus on maximizing project value.

Feb 1, 2024

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By T. Geyer

The Carbon Disclosure Project (the pre-eminent global initiative for institutional investor collaboration on climate change) groups the business risks (and opportunities) related to climate change into four categories: 1. Regulatory risks from tightening legislation (and opportunities for companies that can make the carbon market work for them), e.g. rising costs for carbon and energy-intensive processes. 2. Competitive risks & opportunities generated by a possible decline in customer demand for carbon/energy intensive products (and opportunities from a consequent rise in demand for efficient / low carbon products). 3. Reputational risks from perceived inaction on climate change (and benefits to those perceived to be ?solutions providers?). 4. Physical risks from changes to climatic patterns, e.g. asset damage from extreme weather events; project delays; water scarcity; resource risks as certain crops become no longer viable in certain areas and new supply chains become necessary; and potential human and socio-political impacts. All of these are already having repercussions for businesses in certain sectors and geographies. The understanding of specific impacts of climate change is still evolving but it is clear that climate change will have a material impact on the value of many businesses, either directly or indirectly. Many commentators and analysts consider that rising energy costs are likely to represent the most direct and immediate investment risk that climate change and the resulting regulatory responses will create for business in the near term. However, it is already possible to identify numerous examples of competitive and reputational risks and opportunities that are leading to significant value creation or destruction in business: the success of the Toyota Prius; the rush by the UK?s leading supermarket retailers to ?green? their brands; and the surging fortunes of companies involved in the manufacture of renewable energy generation equipment, are all manifestations of this trend. In addition, the potential physical impacts of climate change are also making themselves felt in certain sectors: an example is the Australian wine industry, suffering after an extreme and prolonged period of drought. THE PROJECT This paper describes a project undertaken for a multinational mining company to examine the physical risks from climate change across its international business operations. The study addressed 163 components of the business and included operating sites (mines, smelters, and refineries), key transport routes (road and rail) and port links. The inclusion of the transport networks and ports is extremely important; key transport routes (e.g. a key railway link) may often be impacted (e.g. by flooding) far more than individual sites due to their large geographic exposure and multiple potential failure points. Extreme weather events causing loss of life and major economic damage continue to be front page news. According to the World Meteorological Organization, January to July 2007 ?was marked by record weather extremes in many regions across the world.? Inevitably, the associated phenomena are starting to impact business and investments, not so much as deal breakers, but in changing the parameters of risk management and the approaches required to devise mitigation measures. EXAMPLES OF EXTREME WEATHER EVENTS No one event can be presented as directly attributable evidence of climate change, however climate change projections suggest that the frequency and severity of many extreme weather events can be expected to increase in a warming world. In August 2003, a heat wave struck Europe, with temperatures as high as 42°C (108°F). As summer temperatures in much of northern Europe rarely exceed 30°C (86°F), the area was unprepared for the disaster, and many thousands of deaths occurred. In August 2005, Hurricane Katrina caused catastrophic damage along the Gulf Coast of the United States, forcing the effective abandonment of south-eastern Louisiana (including New Orleans) for up to two months and damaging oil wells that resulted in increased oil prices. Katrina killed over 1,800 people and caused at least $75 billion in damages, making it one of the costliest natural disasters of all time. This was followed in September, by Hurricane Rita which left 119 people dead along the U.S. Gulf Coast, causing $9.4 billion in damage. In January 2006, hundreds of people were killed when Russia, Eastern Europe and Scandinavia experienced the coldest weather for decades. In summer 2007, dramatic floods in the south central region of England, UK left 350,000 people without drinking water and many without electricity. Transport infrastructure was severely disrupted; combined with floods which occurred earlier in the summer in Yorkshire (North England), the damage is estimated to total over £2 billion. ASSESSING RISKS FROM CLIMATE CHANGE To date, only a minority of companies have attempted to quantify the risks from climate change. However, investors are seeking greater disclosure of climate change related risks and opportunities and it is expected companies that can demonstrate they are prepared for climate change will attract higher market valuations. Climate Change Threats A variety of climate change threats were examined for their potential to have a potential measurable impact on the mining company?s business operations. Those considered most significant were included in the study and are shown in Table 1 (see Appendix A). Certain threats can be considered as being cyclical in nature and the future predictions may suggest a change in the frequency and severity of such events (e.g. storms/hurricanes, rainfall, drought). However other threats are associated with a gradual change over time (e.g. loss of glaciers, loss of permafrost, sea level rises). A slightly different approach is needed to address this differing nature of the threats, as described subsequently. Climatic Regions Much of the research and data associated with climate change is collected and reported on a regional basis. An example of the climate change impacts predicted for a number of climatic regions is shown in Table 2 (see Appendix A).

Jan 1, 2009

"Tell us how you got involved in mining and about your career path.My dad was a coal miner and my uncle was a metallurgist, so when I enrolled at Penn State’s New Kensington Campus, I chose the College of Earth and Mineral Sciences — exact majors didn’t get picked till the end of your sophomore year. Penn State New Ken had an associate degree in mining program and one of the guys in my carpool was going to take Mining 30 in the evening and the other guy (mechanical engineer) was also able to take an evening class. I didn’t want to break up the carpool, so I took Mining 30, complete with essay tests. I could write, so I did well, and the professor said I should go into mining engineering. Fast forward to the end of the next term at University Park, and I realized there wasn’t enough chemistry in mining. Switching to metallurgy would have meant another term at that point, so Dr. Lovell, my advisor, trotted me down the hall and to the next building and said I was a mineral processor. That stuck. I was a summer student at U.S. Steel Research between my junior and senior year and they paid for my master’s degree — all about clay and macerals in coal flotation. During that time, the steel industry tanked, and I thought a Ph.D. would be a good idea — I could always teach at the university level if I had those credentials. The Electric Power Research Institute had a Coal Cleaning Test Facility in Homer City, PA, and I conducted my Ph.D. research on rate and residence time in conventional coal froth flotation cells there and at a local cleaning plant. I went to work at the test facility in 1987 (later CQ Inc.) and stayed there until I started PrepTech Inc. in 1997. PrepTech offers some consulting services for coal cleaning plants and sells mineral processing equipment, mostly to coal companies. I can’t believe it’s been 21 years.And what about your SME career?Of course, I was a student SME member at Penn State. We used many of the SME books in class, so who wouldn’t want the student discount? While in Homer City, I became involved with the Appalachian Plateau Subsection of the Pittsburgh Section. We’d hold quarterly meetings with interesting speakers and had good attendance. I was the secretary. I’m still the secretary and also get the bank statements. We’ll need to close that out some time, but I guess I’ve been hoping for resurgence in the Indiana/Cambria/ Somerset area."

Jan 3, 2018

By Jeff Reid, Mohamed Maghari, Nicholas Joens

The Burnaby Mountain Tunnel was an integral part of the Trans Mountain Expansion Project. General Contractor, Kiewit Ledcor TMEP Partnership (KLTP), contracted with McNally Construction to build an underground tunnel between the Burnaby and Westridge Marine terminals under Burnaby Mountain. The pipeline was constructed within a 2.6-kilometre tunnel, eliminating the need to run the pipeline over the mountain and minimizing community impacts. The complexities of this Project led to multiple innovations, including the design of a Tunnel Boring Machine (TBM) capable of excavating through mixed-faced conditions concurrently thus allowing the Project team to complete the tunnel with limited geotechnical information.

Jun 23, 2024