Search Documents

By Donald L. Gaughenbaugh

Under the terms of the 1970 amendments to the Clean Air Act, the EPA established national ambient air quality standards for a number of pollutants. Sulfur dioxide (SO2) was one of these pollutants. These ambient air quality standards have had perhaps their biggest impact on the power utilities. In an effort to meet the air quality standards set forth by the EPA, utilities using high sulfur fuels have been forced to install flue gas desulfurization (FGD) systems. The majority of FGD systems in operation today are nonregenerable systems, that is the by-product of the system is disposed of, usually into settling ponds. Limestone slurry is the most common reagent used to remove SO from the flue gases. The calcium carbonate (limestone) slurry interacts with the flue gas, absorbing the SO2 and forming a by-product of calcium sulfate/sulfite which is disposed of.

Jan 1, 1986

By Harry E. LeGrand

The purpose of this paper is to outline briefly some basic principles of ground-water hydrology that have application in mine hydrology and to suggest that an understanding of these principles can help to forestall problems that are internal as regards mining operations and external as regards damage or harm to surrounding areas. The development of a mine below the water table pleads for accurate values to answers of hydrologic problems. Such internal problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required mining or milling use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by homogeneous rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where rocks are not homogeneous. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground-water occurrence and movement should be helpful to mine operators. Mining operations that extend below the water table disturb the natural hydrologic regimen. Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine, The behavior of the cone of depression, as it tends to deepen and to increase in areal extent when the mine is deepened, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised. The geologic and hydrologic settings of mines range greatly so that a simple standard procedure for dealing with problems

Jan 1, 1972

By M. Jaramillo

The Expanded West Pit of the 15 MTY El Cerrejon Mine will reach a maximum depth of270 m. Slope stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization call for anchoring the footwall by installation of cable bolts, 9 to 33 m long, of multi-strand steel cable. For each of the 15 m high mining benches, a row of bolts is installed with variable horizontal spacing, depending on dip magnitude. Cable bolting is now standard operating practice and 11800 bolts will have been installed during the life of the mine.

Jan 1, 1995

By M. Javier

Mining, waste is growing problem both physical accumulation and increasing toxic uncertainties it presents in the long run. Its value ?zero? is strictly calculated by economy. This mining model begs the question: What is the value of waste & what does it represent to the mining industry? Waste is widely accepted as a ?by product? generated as a consequences of the mining process. The abundant waste accumulation affects society, as receptor, in many ways and the waste piles of materials has no use and no destiny. In reality, this waste is monument of imperfection of the extractive industries worldwide. Our planet is finite and has strict limitations, which mining has traditionally ignored. It is time to design a new system, in which clearly, waste design must be integrated in whole mining process; it has no room to postpone. This paper presents a concept in waste design by which toxic mining waste not only can be rendered inert but also act as nutrient to help balance the ecosystems. This concept calls for extractive industries to pursue EQUILIBRIUM with nature (Geomimic). Also, this concept offers countless gains and opportunities fro the industry and by converting liabilities into assets; mining engineers become the managers and stewards of nature. Also, waste design offers new solutions for proper and sustainable waste management of the mining industry.

Jan 1, 2011

The support of the roof in coal mines remains a critical safety issue with 3 fatalities from roof falls in 2007 and 430 injuries from roof falls in 2006. A snapshot survey by the authors of room design and support details as well as unplanned falls of ground in the industry revealed some useful data concerning support use, seam details, fall dimensions, bolt lengths and spacing and the stand-up time.

Jan 1, 2009

By B. Arvidson

Computer-controlled machine sorting may, if properly applied, have a dramatic effect on overall economics of a mine operation. Radiometric and photometric sorters have been used for many years and new developments will be reported, such as a sorter for fine particles and a conductivity/magnetic sorter. Application examples with emphasis on precious metals will be given. Economics for some of the projects will be reviewed and discussed. Sorting underground is shown to be particularly attractive, but machine sorting would be profitable in most cases based on savings in transportation and milling/beneficiation costs only.

Jan 1, 1987

By Martin P. Corriveau

It is not news to anyone in the mining industry that federal action in the prevention and abatement of air pollution has seriously affected the industry both directly and indirectly. It is the purpose of this paper to review how the development of federal action is directly affecting the coal mining industry's number one customer, the fossil-fuel-fired steam generating power plants and, consequently, the industry itself indirectly. In essence, Public Law 84-159 of 1955 as amended by the Clean Air Act of 1963 and its revisions in 1967 and 1970 progressively tightened federal coordination and management of air pollution control programs throughout these United States. The Environ- mental Protection Agency (E.P.A.) set up to direct the programs was charged to establish National Air Quality Standards, Standards of Performance for New Stationary Sources, and National Emission Standards for Hazardous Air Pollutants.

Jan 1, 1973

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

By Edward J. Adams

In recent years, there has been a shortage of individuals trained in the technical skills entering the mining industry. The university and industry, both indicating their concern, have joined efforts in an attempt to do something about this situation. An example of such an effort is the Pennsylvania State University's Student-Trainee Program in Mining Engineering, now in Its third year. The program is a five-year plan in which six months of schooling and six months of on-the-job training are alternated, climaxed by the student trainee earning a Bachelor of Science Degree in Mining Engineering plus two years of practical experience. The student trainee accepts the work-study plan as a satisfactory method of receiving a thorough education and preparing fog a career in the mining industry. Inasmuch as the work and study-periods are alternated, the trainee has an opportunity' to integrate his practical experience with his academic knowledge. He receives a chance to observe others perform she duties of the profession he is preparing to pursue, and he regards this as an essential part of any such cooperative effort. Even though there are some disadvantages, the trainee feels that the advantages of the program are definitely more decisive.

Jan 1, 1963

By C. D. Harrison

The 1990 Clean Air Act Amendments specify national objectives for reducing sulfur dioxide emissions from coal-fired power plants System-wide reductions can be achieved by combining various emissions controls technologies and allowances, or compliance credits, that can be purchased, sold, or traded. As part of the Coal Quality Expert development project funded by U.S. Department of Energy and the Electric Power Research Institute (EPRI), Black & Veatch has developed an interactive computer tool, the Acid Rain Advisor (ARA). ARA allows the user to develop integrated system-wide compliance plans by comparing the costs and emissions reduction benefits for emissions allowances and various SO2 control technologies such as coal cleaning, fuel switching, and scrubber retrofits.

Jan 1, 1992

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

By Thomas L. Mell

Continuous processing plants handling liquids have achieved a high degree of centralized automatic control. Many chemical plants are operated from one room, with automatic control of the various process flow rates. These plants know from experience that automatic control can produce higher through-put, better uniformity of product, decreased operating costs and reduction of storage capacity, Plants which process materials in the form of bulk solids have not been able to use control to as great an extent, primarily due to the lack of measuring equipment capable of providing the same types of continuous automatic control available with liquid flow meters. This paper will describe a scale for measuring flows of bulk materials on conveyor belts which is particularly adaptable to remote centralized instrumentation and automatic control, and will also describe some typical control applications. Fig. 1 illustrates the basic method of measurement of this scale. A conveyor belt idler is supported on a rigid carriage which in turn is mounted in two anti- friction bearings on the conveyor stringers. The pivoted carriage is prevented from rotating about the pivot shaft by an electric strain gauge load cell connected between the carriage and a cross support. Increasing load on the conveyor belt increases the moment of the carriage frame about the pivot shaft, and proportionally increases the tension in the load cell. The belt speed is measured by a conventional d. c. tachometer generator driven from a pulley, usually on the return belt. The speed signal from the tachometer generator and the load signal from the load cell are combined to produce a signal proportional to the flow rate of material in tons per hour, or lbs. per foot, or equivalent units, It will be important to remember, in considering various control applications, that the flow rate of material on the belt is composed of these two component signals, namely the weight of material and the speed at which it is moving. The feed rate is then indicated and recorded by a self-balancing potentiometer of the type used for measuring temperature by means of thermocouples. These instruments may also be equipped with integrating mechanisms reading the totalized tonnage over a period of time.

Jan 1, 1958

By L. I. Gyrskia, Y. V. Andreev, T. N. Greiver, G. V. Petrov

Traditionally, chromite ores are regarded exclusively as a monomineral raw material for extraction of chromium. The results of the investigations indicate a wide range of PGM in the Ray-Iz chromites, amounting to 1-3 ppm PGM. The study of products of primary gravity concentration from heavily and lightly disseminated ores (Tsentralnoe deposit, Ray-Iz block), showed that the platinum-group minerals are concentrated in the tails and slimes of the processed products, containing 10-30 ppm total PGM. Preliminary data make it possible to conclude that an in-depth study of the platinum mineralogy of the Ray-Iz block chromite ores is necessary to develop a process that will produce both chromium and the PGM.

Jan 1, 2000

By J. Kretschmann, P. Goerke-Mallet, C. Melchers

Mining always leaves a mark behind. Dealing with this legacy is not only a tremendous challenge in Germany, but internationally too. The Technical University Georg Agricola (THGA) in Bochum, Germany, has established a Research Center for Post-Mining. Researchers combine expertise from a variety of technical and nontechnical fields in their quest to shape the post-mining era that completes the mine life cycle. In this respect, the Research Center focuses on four research areas: Perpetual tasks and mine water management, Geomonitoring, Material sciences and site transition. With more than 200 years of successful partnership with the mining industry in Germany and abroad, THGA offers a perfect setting for fresh and sound ideas in order support mining’s social license to operate. The aim of the paper is to describe the Post-Mining Research Center along with exemplary research projects that are of interest to the mining industry globally and to foster technical communication and research networking.

Mar 2, 2022

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By Pierre Filiatreault, Brian Straight, Stephanie Thibeault, Devin Castendyk, Londie Cameron

"Working on or near water at active, closed or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the U.S. Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at U.S. metal, non metal and coal mines (MSHA, 2000). Openpit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including: a) drowning, b) hypothermia, c) falls to the ground from the top of high walls, d) collapse of unstable access roads, e) rock falls and avalanches from pit walls, f) avalanchegenerated tsunamis traveling across the lake surface and g) rapid degassing events.Some pit lakes are simply not safely or easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on a regular basis is needed to monitor the evolution of water quality over time, verify the accuracy of numerical predictions and, ultimately, manage lake water chemistry and ecological risks. For pit lakes with surface water discharge, regular monitoring is used to appropriately design and adjust water treatment plants in order to produce acceptable site discharge water quality.As a product of these risks and the need for water samples, mining companies spend considerable expense on pit lake safety as part of monitoring programs. This includes training personnel for on water duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices and cold-water clothing called mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface and employing spotters who can directly communicate with emergency medical services to watch sampling activities because cell phones and radio signals can be blocked by pit walls. Some sites utilize redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires two boats on the water during pit lake sampling events, with a third boat on the shoreline, gassed and ready to go. In addition, water samplers are required to hold Marine Emergency Duties training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel in the event of an accident."

Jan 7, 2017

By F. Heivilin

"Health and Safety problems can make a mineral deposit or a portion of one, an operating plant, or finished product unprofitable or worthless. Therefore they need to be reviewed when reserves are established and yearly thereafter until the deposit is closed down. Health and Safety regulations serve as a guide, but I have always done more frequent checks, when adding new products with different specifications or during times of bad weather and crisis. Water quality and quantity are always in question. Health and Safety are quality of life issues which are at or near the top of priorities for communities, companies, employees, and government bodies. Georgia dropped from one to three in U. S. for business development due to “Quality of Life” issues. Remember crystalline silica is present in nearly all sedimentary and acidic rocks and basic igneous rocks are the perceived home of asbestos. These health issues, any other safety and health issues or perceived issues need to be resolved initially and any time they come up during life of deposit. When handled properly good safety and health programs add to the profitability of a deposit, not to the costs. Daily safety checks in operating plants and mines, and visual check of all drilling core with an eye for changes are a key to successful programs. Both plants I turned around had terrible safety records, too much airborne dust, and maintenance problems resulting in low productivity. In almost every case cost reduction was tied to eliminating maintenance and spillage problems which caused health problems and increased possibility of accidents. Implementation of these safety and health programs around 1970 starting prior to government programs, working with new MSA/MSHA regulations, working to improve the regulations as a president of a state mining organization, and maintain profits was a challenge, but very rewarding. Reducing time to make repairs and work simplification gleaned from observations and employee recommendations learned from making multiple daily inspections resulted in years without lost time accidents at two plants, reduced maintenance and 33-75 % improvement in cost per ton at A. P. Green Refractories Co. Eufaula Calcining Plant 1972-77 and Oil-Dri Ochlocknee plant and mine 1979-82. The Ochlocknee mine worked 1981-2007 without a LTA. The author participated in 16 acquisitions and new plant design projects. All of above reduced costs allowed mining deposits with higher overburden to be used and considered. Thereby increasing reserves considered in all operations."

Jan 1, 2016

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10µm. The current study examined the effects of operating conditions on centrifuge performance. The test conditions included centrifuge bowl and scroll speeds, volumetric feed rates, solids concentration, and pond depth. Centrifuge performance was evaluated using partition curves, along with product yields and solids concentrations.

Jan 1, 2000