Search Documents

By Stanley Kesler

The first of two initial 650-mw units of the Paradise Steam Station, located on the banks of the Green River in the south-central portion of the western Kentucky coal basin, is scheduled for operation in late fall of 1962. Location of the site is shown on the map of figure 1. This plant will be the eighth, large-capacity,, modern station built by TVA in a series starting with Johnsonville, operated first in 1951. During that period of 10 years,, unit sizes have increased from a capability of 125 mw to 500 mw at the recently completed Widows Creek Unit 7 addition and at Paradise to 650 mw. This new unit will take its place in a power system that serves an area of some 80,000; square miles with a present installed capacity of over 12,000 mw. Upon completion of the Paradise units and other additional hydro and steam units presently under construction, the system capacity will have reached over 15,000 mw. Projected load estimates indicate that this system will provide a margin' of slightly under 10 percent of dependable capacity above peak demand at that tire. One Paradise 650-mw unit at that time will represent approximately 4 percent of the total system installed capacity.

Jan 1, 1962

By Peter Schmäh

Pipe-jacked tunnels are considered for a large variety of applications from water and sewage, cable ducts to challenging pipeline crossings or landfall construction. In most cases, Slurry MTBMs are used to carry out these projects. Continuous further development of technological features for pipe jacking plays a key role to overcome feasibility limits and to meet increased project requirements. As tightened safety regulations in terms of accessibility and escape routes increasingly limit the options of small segment lining tunnels in the diameter range below 4 m, 13 feet, pipe jacking has partially taken over. During the last decades, a growing number of large-diameter and long-distance pipe jacking projects have been completed. Experienced contractors successfully use the technological capacity of the MTBM equipment. The machine and cutting wheel have to be designed according to the ground conditions. Bentonite lubrication and interjacking stations are key factors to keep push forces moderate. For long pipe jacking drives, a so-called push module can be installed in the machine can, to be able to switch from pipe jacking to segment lining in case the machine gets stuck. The overall aim is to provide clients and the tunnel construction industry with safe and economical solu- tions for successful project execution. This presentation will present international milestone projects and will also discuss the latest developments in automation, related opportunities and limitations, and the future of digitization and artificial intelligence in pipe jacking.

Jun 23, 2024

By Lynn B. Hales

Unfortunately, the term "control" has a negative connotation in the minds of many of our operating plant personnel. Whereas the opposite is true of those associated with research and technical centers in our industry. The magnitude of this difference in opinion and actual experience has often proved to be a major factor influencing the success or failure of process control applications. Through the years, many plant people have endured a number of unsuccessful attempts by "outside" people to "optimize" their plants; and these experiences have proved to have had quite a callousing effect on them. On the other hand, in many plants, successful process control efforts have made firm allies of the operating personnel, and have increased the number of metallurgical people who are well qualified and experienced in process control. The instrumentation industry, computer industry, and the mining industry's ability to quantify what is really happening in our processes have grown and developed rapidly since the first control efforts were made in the 1930's (1). Because of this-,: new control opportunities are becoming increasingly more feasible and older well established ones are becoming even more practical and necessary with regard to the economic s of our industry.

Jan 1, 1979

By Erwin K. Roesner

The difficulties encountered while sinking deep shafts for Potash Mines in southern Saskatchewan have been the subject of several papers in the past. Geological and hydrological conditions of the strata overlying the potash deposits require special techniques for ground and water control during shaft sinking. The easily soluble potash ore requires the lining of these shafts to be virtually watertight to assure long term and safe operation. This paper describes the construction of the most recently completed potash shaft for the Potash Corporation of Saskatchewan. The shaft was designed and constructed by Thyssen Mining Construction of Canada Ltd. and it is located near Lanigan, approximately 110 km east of Saskatoon.

Jan 1, 1980

Mineral sands mining for ilmenite, rutile, and zircon will disturb over 2,500 ha of prime agricultural farmland in Virginia and North Carolina (USA) over the next 20 years. Mining of the Virginia deposit was initiated in 1997 and approximately 750 ha have been disturbed to date with approximately 150 ha reclaimed to support a mix of agricultural post-mining land uses. While considerable university research and corporate effort were devoted to developing environmental management systems and reclamation protocols for these lands, specific indicators of sustainability and restoration success were lacking. By 2003, it became apparent to the mining operator (Iluka Resources), local land-owners/farmers, local government, and the regulatory authority that testable indicators of reclamation success were essential for long-term sustainability. Virginia Tech worked cooperatively with all stakeholders to review the pre-existing research base and to propose reasonable expectations of post-mining soil productivity levels. The state regulatory authority reinforced its position on a number of associated issues including necessity of topsoil return and specific comparative crop yield targets. Virginia Tech, Iluka Resources, and a local leaseholder (Carraway-Winn family) agreed to jointly manage a 45-ha research demonstration farm where the effects of alternative soil reconstruction practices are being rigorously monitored for both row crops (corn and wheat) and forage production. All mined land crop yields are also compared to an adjacent undisturbed exceptional quality prime farmland soil. Corn and wheat yields in 2005 and 2006 were significantly above county average yields (regulatory target level) and approximately 75% of undisturbed adjacent prime farmlands. This cooperative effort allows all clientele groups to objectively assess the post-mining productivity of these mined lands while providing an invaluable educational opportunity for the mining industry.

Jan 1, 2007

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

By Michael N. Greeley

The movement to reclaim abandoned mine sites has gained momentum as federal, state, and private organizations have increased their commitment and resources to tackle mutual, and often controversial, problems of health and safety. Numerous interorganizational agreements have been implemented to promote cooperation in the characterization of mine site hazards, development of mutually acceptable plans of remediation, and sharing of actual cleanup requirements. Working through these partnerships, the federal land management agencies have begun to focus on abandoned mine reclamation in selected, priority watersheds and other drainage basins. Although there are major difficulties to overcome, significant progress continues to be made.

Jan 1, 1999

By Remo Grandori

"INTRODUCTIONDouble Shield TBMs were introduced in the market in the early seventies with three main targets:• Increase the TBM performances in term of advance per day thanks to the ability to erect a segmental lining simultaneously with the excavation phase.• Be able to advance through unstable and disturbed rocks under the protection of the shields• Provide a finished tunnel by installing a precast lining as the TBM advance.In 2003 SELI developed the design of the Double Shield Universal (DSU) TBM as an evolution of the original Double Shield TBM design.This new TBM design was targeted to improve: the TBM capability to advance through squeezing/converging rock formations under high cover, the telescopic joint design (allowing by such to operate the machine in double shield mode in very weak rock), the capability of the TBM to investigate and treat the ground around and ahead of the tunnel face.In the same lapse of time Single Shield TBMs, originally utilized for soft ground tunnelling, extended progressively their range of application to mix rocks and finally to hard rock tunnelling with increasing performances.This also thanks to the substantial reduction in the installation time of the segmental lining ring that contributed to minimize the TBM stand by time between two consecutive boring strokes.Today the choice between the two types of TBMs needs to be carefully evaluated project by project since one type of TBM may “prevail” in certain geologies and diameters and vice versa.THE VISHNUGAD PIPALKOTI TUNNELThe Vishnugad Pipalkoti Tunnel is part of the 444 MW Vishnugad Pipalkoti Hydro Electric Project (VPHEP) on Alaknanda river in Uttarakhand (India).The Owner is the Indian electric company “Tehry Hydro Development Corporation” (THDC) and the World Bank finances the project.The Headrace Tunnel total length is 13.4 Km and a section of about 12,3km will be excavated by TBM by SELI Overseas (Italy) in subcontract to HCC (India) the General Contractor for the project. The TBM will be delivered ex workshop in March 2016 and it is foreseen to start boring in the second half of 2016.Figure 1 below shows the location of the project and the following Table 1 summarizes the geometrical characteristics of the TBM tunnel."

Jan 1, 2016

By A. A. Davis

The decade of the 70?s saw a series of landmark environmental resource programs enacted by the Congress. Many states followed suit, so that by the end of the decade air quality, water pollution, and the conservation of other natural resources, including minerals, were the subject of a wide-ranging body of laws, policies, regulations, and procedures. Many of the actions required or permitted by this rule-making involved areas for which adequate information and substantial experience were not available. Moreover, goals and objectives were sometimes established which were enormously difficult to achieve technically, or of such formidable expense as to cause concern about their consequences in the marketplace. It is therefore hardly surprising that one product of all this activity has been a mass of litigation. Court dockets are crowded with suits and counter-suits involving both substantive and procedural aspects of environmental protection. Indeed, it is probably fair to say that the volume and range of environmentally-related disputes brought before the courts parallels that generated by the civil rights movement a decade ago. There were also some new dimensions to the environmental movement. For the first time, the national environmental policy act required agencies to prepare environmental impact statements when proposed projects or activities would have substantial impacts on environmental resources. Another requirement of many of the new programs mandated meaningful citizen participation in public decision-making. Here, as elsewhere, the purpose was admirable, but guidelines were vague, and the result often was inaction, polarization, and litigation.

Jan 1, 1986

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005

By B. Simser, T. Butler

Glencore’s Nickel Rim South Mine, located in Sudbury, Ontario, Canada, is a primary/secondary blasthole operation with ore zones lying between 1,100 and 1,700 m below surface. One of the main benefits of the primary/secondary mining method in high stress ground is that up to 50% of the mining will take place in secondary stopes that should be in a yielded rock mass state. Every future secondary mining stope begins as a primary stope abutment pillar. As with many mines, the stress loading history and rock mass conditions can vary considerably in space and time. Safe mining practices cannot allow for an assumption that the planned secondary stopes are indeed yielded. An incorrect assumption can result in mining development and stoping taking place in high stress ground rather than the expected yielded rock mass conditions. This can result in higher levels of seismicity than expected and incorrect ground support recommendations in areas where workers could be exposed. Seismic monitoring is the mines’ premier tool to track the actual rock mass response to mining. Yielded zones have a reasonably clear seismic signature/pattern over time that is visible in the collected data. The ability to accurately locate small magnitude seismic events can help define and delineate different stages of rock mass failure. The vast majority of the seismic data recorded by the microseismic monitoring system is below moment magnitude (Mw) 0.0. Examples are provided showing how small seismic events (Mw < -1.5) can help provide feedback from the rock mass deformation that allows the ground control engineer to gain a better understanding of how the rock mass is responding to mining processes.

Apr 26, 2022

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay, Cicek Sena, Zhao Haochen

"Analysis of Longwall Pillar Stability (ALPS) and Analysis of Retreat Mine Pillar Stability (ARMPS) treat the pillar as a passive structure that is designed to carry overburden dead-weight. This dead-weight is calculated by simple rules based on the geometry of the mining, such as “tributary area theory,” “pressure arch theory,” and “abutment angle theory.” Although the pressure arch loading approach indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology of the overburden in load calculations. The relationship between successful pillar layouts and overburden geology can be incorporated into the load calculation by using the Ground Response Curve (GRC) approach.This paper introduces the GRC modeling methodology to investigate the effect of overburden geology and excavation geometry on load transfer mechanisms using seven field measurement case studies from four U.S. mines. It was also shown that the modeling methodology used to derive GRC in this study approximates mining-induced stresses and deformations within 5% of the values measured in the field.INTRODUCTIONFrith and Reed (2017) stated that current state-of-the-art pillar design methods ignore the overburden mechanics and use estimated dead-weight of overburden to compute pillar sizes. In the United States and around the world, overburden loading is typically estimated by simple geometric rules, generally with the tributary area theory (TAT). The specific overburden mechanics, structural competence of the overburden strata, geology, in situ stresses, and overburden/pillar interactions are typically ignored. However, these important mechanical responses affect the stability of the mine pillars and openings; therefore, they also affect the safety of the mine workers.Research conducted by the National Institute for Occupational Safety and Health (NIOSH) after the Crandall Canyon mine disaster (Esterhuizen, Mark, and Murphy, 2010) showed that small panel width-to-depth ratios and stiff-strong overburden result in a reduction of the observed pillar loads, much smaller than the TAT estimate. In fact, as a response to the Crandall Canyon disaster, Mark (2010) implemented a pressure arch loading approach into the latest ARMPS program to recognize the inherently greater stability of narrow panels at depth. The pressure arch approach is a first logical step to introducing non-tributary area loading into the practical ARMPS program. Although the pressure arch loading indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology and mechanical response of overburden in the load calculations."

Jan 1, 2019

By James K. Gowans

The Red Dog Operation is located in northwestern Alaska at Latitude 68°, 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The orebody was acquired by the NANA Regional Corporation, (an Alaska Native Corporation established by the Alaska Native Claims Settlement Act of 1971), in 1980 in their land selection. In 1982 Cominco American and the NANA Corporation signed a development agreement and Cominco Alaska Inc., a wholly owned subsidiary of Cominco American, was formed to manage the Red Dog Project. An extensive exploration program in 1980 -1982 outlined a mineral inventory of 85 million tons, at a grade of 5.2% Pb, 17.1 % Zn, and 2.4 oz/ton Ag, which makes the Red Dog the second largest deposit ever discovered. Broken Hill, in Australia, is the only zinc orebody which was originally larger than Red Dog. The design of the facilities is to process 2.1 million tons of ore annually, which will produce 560,000 tons of zinc concentrate, 100,000 tons of lead concentrate and 50,000 tons of bulk lead/zinc concentrate.

Jan 1, 1991

By Ora H. Rostad

Veins containing silver and gold values, with some associated values in copper, lead, and zinc, were discovered in 1890 by Will Kirwin in what was later designated the Kirwin mining district situated on the North Fork of the Wood River, about 56 km (35 miles) west of Meeteetse. (See Fig. I.) After considerable prospecting activity, including the driving of several short adits on veins, most of theclaims in the district were consolidated into two ownerships. One was held by the Galena Ridge Mining Co. which was organized on Nov. 18, 1902. The other was held by the Shoshone Mountain Mining Co. which was organized on Mar. 23, 1903. During the period from 1903 to 1907 inclusive, the two companies continued exploration on veins in their respective areas. The major exploration-development activity for the Galena Ridge Mining Co. was the driving of the Galena Ridge crosscut adit for 709 m (2327 ft), to cut veins at depth which had been explored by short adits high on Galena Ridge. Shoshone Mountain Mining Co. concentrated their work on the Bryan and Pickwick veins. Neither of the companies found ore that was rich enough to sustain profitable operations in that remote locality. Most of the major exploration and development activities were stopped in late 1907. A major snowslide in February 1907 killed three people and destroyed several buildings and may have contributed to discouragement in the area. From 1908 to the early 1920s, only minor exploration work was done. Galena Ridge Mining Co. was dissolved Aug. 5, 1922, and Shoshone Mountain Mining Co. was dissolved on Mar. 23, 1923.

Jan 1, 1991

By B. N. Thompson

The main industrial minerals produced are non-metallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. The other minerals, some with minor production, include diatomite, feldspar, magnesite, sulphur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of Late Cenozoic acidic volcanic rocks.

Jan 1, 1982

By W.J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 from New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be relatively widespread through much of the Tasman Fold Belts of Eastern Australia and production to date is estimated to be some 500 000 carats from a number of &apos;small alluvial fields. Despite extensive exploration though, no primary rock source carrying significant diamond contents has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia over the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives, of which 180 have been confirmed to be diamondiferous. Only one pipe however, the 1200 Ma high grade Argyle lamproite and associated near-by alluvials, has proved to be economically exploitable with current annual production of 40 million carats valued at approximately US$400 million. Production from the open-pit will be sustainable until at least 2003. This paper briefly summarizes the history of diamond discovery in Australia, principal diamondiferous provinces and deposits, current exploration activities and the potential for future discoveries.

Jan 1, 1995

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By Juan Ares, Enrique Fernández, Alejandro Sanz, Francisco González

"INTRODUCTION Crossrail is a subsidiary company of Transport for London created for the construction of a new transverse train line 118 km long between Maidenhead and Heathrow in the West, and Shenfield and Abbey Wood in the East, including 21 km underground below London. Crossrail C305 Eastern Running Tunnels project is the biggest contract within Crossrail Project and involved boring 11.8 km of twin tunnels through London’s city center. Crossrail C305 Project interfaced with different contracts along its alignment and therefore logistics and solutions had to be developed to minimize disruptions or interferences with other contractors and the neighborhood. The paper describes this innovative approach. C305 CONTRACT APPROACH C305 contract was split into three drives, to be excavated by four EPB TBMs 7.1m diameter, as shown in Figure 1. •,Drive Y: 8.2km long between Limmo Peninsula and Farringdon Station in the city center •,Drive Z: 2.7km long between Pudding Mill Lane and Stepney Green Junction •,Drive G: 0.9km long between Limmo Peninsula and Victoria Dock Portal in the East. Crossrail C305 Project scope of works included the excavation of TBM tunnels and shafts at Limmo Peninsula and Stepney Green (including 17m span turnout caverns), along with the requirement to traverse station and shaft structures of other Crossrail contracts. Limmo Peninsula Site was a strategic element as it was the only access point on the tunnel alignment with sufficient available area at the surface for tunnelling logistics and also connected to the Lea River, tributary of the River Thames which facilitated marine operations for segment supply and muck removal. These were the reasons for operating Drive Y & Drive G TBMs from that location. Drive Z TBMs were originally planned to be launched from Stepney Green to Pudding Mill Lane, supplying the TBMs during Drive Z excavation from Limmo Peninsula site through the excavated section of Drive Y between Limmo and Stepney Green. During the early stages of the project, a value engineering proposal with a new tunneling strategy was agreed wherein the Pudding Mill Lane contractor would provide space for TBM assembly and operation in their portal, allowing for reversing Drive Z excavation and launching the two TBMs from Pudding Mill Lane. This optimization reduced some of the shaft requirements at Stepney Green which were contingent upon critical enabling works and provided program certainty and cost savings for the full Crossrail Project. It allowed for the reuse of both the Drive Z TBMs for Drive G excavation from Limmo to Victoria Dock Portal thereby saving on the procurement of two TBMs, in addition to easier logistics for both Drives Y&Z, therefore de-risking the TBM excavation process and the C305 Project program completion."

Jan 1, 2016

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974