Search Documents

By John W. Crawford

The majority of the regulations in Part 75 for underground coal mines have been in effect since March of 1970, almost nine years now. Although there have been some additions each year in specific areas where the need became apparent or the statute required some action, the bulk was promulgated on March 28, 1970 for the purpose of clarifying the statutory provisions of the Federal Coal Mine Health and Safety Act of 1969. Many of those regulations were derived from the Federal Mine Safety Code, or from experience gained by the Bureau of Mines in the enforcement of Public Law 552. Upon passage of the Federal Mine Safety and Health Act of 1977, these same regulations remained in effect and the statutory requirements of the Act placed a responsibility upon the Secretary of Labor to promulgate additional regulations in specific areas not previously covered. The Federal inspectorate has received formal training at the National Mine Health and Safety Academy in the proper application of the regulations, as well as routine retraining and special training courses subsequent to the promulgation of new regulations. With some exceptions, the vast majority of these regulations are nothing more than good mining practice. Basically, the regulatory problems are two-fold. There are a few specific regulations that, under certain circumstances, compliance is nearly, if not actually, impossible. There is non-uniform application of enforcement of regulations by the inspectorate based on opinions developed from personal experience of inspectors or lack of experience. The record is replete with examples of overzealous inspectors applying regulations that either do not exist or have been stretched far beyond the intent of the regulations.

Jan 1, 1979

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group's mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974

By E. H. Bentzen

The purpose of this paper is to explain the production of sand for glass manufacturing and the reasoning behind the sand specifications set by the glass industry. In order to discuss the production of glass sand, there is a need to understand what glass is and how it is made. Therefore this paper discusses glass, as well as sand beneficiation.

Jan 1, 1977

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the US Bureau of Mines has developed a PC-based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1995

By R. Barthel, O. Nitzsche, J. Pateiro Fernández, T. Cramer

The Hong Gai coal field in northeast Vietnam has been the main coal mining area of Vietnam for more than 150 years. Anthracite coal is produced from several open pit and underground mines situated close to the UNESCO world natural heritage site Ha Long Bay. The mining-induced environmental impacts such as dust emissions, acid mine drainage, and visual impairments due to waste dumps resulted in severe conflicts of interests regarding future land use and the protection of the world natural heritage site Ha Long Bay. Within the RAME project (Research Association Mining and Environment in Vietnam), Brenk Systemplanung is contributing to an improved environmental and sustainable planning in Vietnam's mining industry and the reduction of environmental impacts on Ha Long Bay by developing suitable and sustainable technology and planning measures (e.g. for dump construction/rehabilitation, predictive modelling, and/or monitoring) for Vietnam's leading coal producer.

Jan 1, 2011

By P. Lopez, E. Wellman, N. Risso, A. Anani

Current machine learning models used for roof fall hazard prediction are mounted on expensive sensors, computationally expensive, or lack the robustness for accurate prediction in the underground mining environment. This research aims to provide a design methodology for a robust, low-cost, deep learning-based algorithm for underground mine roof fall hazard prediction. A data sampling plan is developed to ensure the replicability and robustness of the developed model. In addition, feature engineering and transformation methods are described to identify relevant features for hazard identification. The methodology described here will be used in model development, tested, and implemented as a real-time mobile device application. The new tool will be expected to detect roof fall hazards in real-time and contribute to a crowdsourcing approach for underground hazard detection.

Feb 1, 2023

By J. C. Reid

Pre-cambrian scheelite deposits in Northeastern Brazil are widespread in a high grade metamorphic terrain. Previously these deposits had been interpreted as contact-metasomatic. In this paper, a volcanigenic model is invoked based on the volcanic setting (proximal to distal) and the absence of associated felsic intrusives and spatially associated metasomatic skarns. The tungsten was introduced into sediments by volcanic- exhalative processes and subsequently remobilized and further concentrated by heat and metamorphis fluids associated with high-grade metamorphism and migmitization. An alternative syngenetic - diagenetic model is discussed which requires the transport of tungsten by heteropoly acids and deposition of the tungsten as a function of Eh and Ph conditions and different clastic depositional environments. While such stratabound tungsten deposits are considered rare in North America, the hypotheses developed in this paper may open new areas for exploration.

Jan 1, 1983

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By J. J. Zaluski

The Surface Mining control and Reclamation Act (public Law 95-87) (here-inafter the "Act" or "SMCRA") passed by congress in August of 1977 represents a comprehensive federal scheme for controlling surface coal mining and the surface effects of underground mining through permitting requirements, performance guidelines, and reclamation planning. While the provisions of the Act have been the subject of numerous legal challenges and court battles over the years, it is difficult to identify a more controversial program within the Act than the provisions for designating lands as unsuitable for surface coal mining operations. The lands unsuitable designation process provides for the acceptance and review of petitions submitted by citizens or organizations seeking to have specified land areas designated unsuitable for all or certain types of surface coal mining activities. In filing these petitions, the interested parties or petitioners are required to make allegations about potential adverse impacts on people or the environment and submit evidence supporting their allegations.

Jan 1, 1992

By W. D. Monaghan

Flame cutting and welding is one of the major causes of fires and explosions in underground U.S. coal mines. On May 20, 2006, a flame cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On January 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame cutting and welding operation at the Loveridge Mine caused a fire that resulted in sealing of the mine for an extended period. Finally, on March 19, 1992, an explosion at the Blacksville No. 1 Mine that was caused by welding resulted in four fatalities. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame cutting and welding operations to determine the root causes of these types of fires and explosions. The methodology included interviewing mining personnel who perform flame cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations, and MSHA reports of investigations and accidents statistics were analyzed. The results were used to identify and compare differences between flame cutting and welding practices and techniques in small and large mines, Eastern and Western mines, low seam and high seam mines, room and pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices and interventions were developed to reduce the number of fires and explosions caused by flame cutting and welding. This paper provides a summary of this work. Disclaimer: The finding and conclusion in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupation Safety and Health.

Jan 1, 2009

By F. Habashi

The changes that took place in China between 1984 and 2004 are remarkable. Visits were made to universities, research institutes, metallurgical industry, and many cultural centers within five trips during this twenty years period. The impressions of these visits are outlined.

Jan 1, 2007

By William T. Barrett

It is said that Thales of Miletus, 600 B.C.,1 was aware of the attraction of lodestone toward iron and highly magnetic minerals. However, the birth of magnetic concentration followed shortly after the invention of the first electromagnet by Sturgeon in 1825. Sturgeon's magnet was described in the annals of electricity.2 The first attempts to concentrate minerals by the use of magnets date back to about 18473 but the first commercial drum-concentrator was apparently invented by R. Cook in 1849. Credit must also be given to the invention of P. Righter's machine in 1867,5 and to the highly successful Wenström separator devised in Sweden in 1883.8 Since the advent of these early separators there have been virtually hundreds of patents granted covering minor modifications of drum-type magnetic separators. The more important advances from a technological viewpoint have been the design of stable power supplies for d.c. magnets, the advent of ceramic permanent magnets which are now replacing electromagnets for the concentration of ferromagnetic minerals, and advances in general magnet and machine configurations.7 One of the problems facing both the designer and the user of magnetic separators is the evaluation of the body forces acting on particles in the magnetic field of the separator. Perhaps the most elegant method of evaluating the body force associated with a drum-type magnetic separator is that recently suggested by W. F. Brown.8 Brown measures the radial component of the field intensity one-half inch from the drum surface and fits a Fourier series in the angle about the drum axis (Figure 1). Once the coefficients of the series are known, it is then possible to calculate [ ]

Jan 1, 1970

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008

By J. Evans

INTRODUCTION Section 209(b) of the Federal Land Policy And Management Act of 1976 (FLPMA-43 U.S.C. 1719 b) authorizes the Secretary of the Interior to convey mineral interests owned by the United States where the surface is or will be in non-Federal ownership. The objective is to allow consolidation of surface and subsurface (mineral) ownership. Certain major conditions must prevail for a conveyance to occur. These are: 1) There are no known mineral values (KMV) or 2) Where the mineral reservation interferes with or precludes appropriate non-mineral surface development and that non-mineral development is a more beneficial use of the land than the mineral development. Remember that allegation, hypothesis or speculation that the conditions could or may exist in the future will not be a sufficient basis for conveyance. Convincing factual evidence for an applicant’s case for mineral conveyance must be made in order to achieve that conveyance. See 43 CFR 2720 0-1 to 0-3, and 0-6. CONCEPT OF KNOWN MINERAL VALUES Known mineral values means mineral rights in lands containing geologic formations that are valuable in the monetary sense for exploring, developing, or producing natural mineral deposits. The presence of such mineral deposits with potential for mineral development may be known because of previous exploration, or may be inferred based on geologic information (43-CFR 2720.0-5(b).

Jan 1, 2007

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011

By Cheng Ang, Yun Bai, Zhi Liu

"This paper presents a conceptual design of an innovative tunnelling method named the Ring Pipe Jacking Method (RPJ) which is conducted by the Ring Pipe Jacking Machine (RPJM). The RPJM consists of a double ring shell which forms a ring section where small interlaced cutter heads or several micro tunnelling machines are assembled to cut soil. Similar to the conventional pipe jacking method, the RPJM also needs a thrust system, a slurry transport system, and a control system. To satisfy the need for large/super large or special section tunnels in future, the RPJM is designed to reduce sharply the excavation face to the annular section, thus enhancing the face stability. Part of the innovation is that the RPJM uses modular cutter heads or micro-TBMs which can be reused. The typical double shield shape can be easily changed by reinstalling the modular cutter heads. Modularity allows the tunnel to be cut in any cross-section shapes, ranging from a circular tunnel to a rectangular one. INTRODUCTION The demand and requirement to utilize urban underground space is rising with the rapid social development in recent years. It is necessary to reduce excavations of the urban ground surface to ensure smooth traffic in cities. Therefore the conventional open cut construction method for underground tunnels can no longer satisfy the need of practical engineering, and it is taken over by trenchless technologies .The Pipe jacking method is an important trenchless technology and is used more and more frequently to install underground pipelines, but the present pipe jacking method still has many problems. For example, it is not suitable for installing large-diameter tunnels and it also has difficulty in construction of short radius curved tunnels. This paper presents a conceptual design of an innovative pipe jacking machine named the Ring Pipe Jacking machine (RPJM) and introduces the correspondent Ring Pipe Jacking Method (RPJ) which can be applied to construct large-diameter tunnels. Furthermore, technical characteristics and superiority of the ring pipe jacking method are analyzed in this paper."

Jan 1, 2016

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By H. Ipek

Industrial grinding machines used in the mineral processing industries are mostly of the tumbling mill type. These mills exist in various types: ball, rod, pebble, autogenous, and semi-autogenous. Balls and rods are traditionally media shapes used in the tumbling mills. In resent years, as an alternative to balls, grinding charges with various shapes are being used. Cylpebs are slightly tapered cylindrical grinding charges with length equaling diameter, and all the edges being radiused. Cylpebs of equal diameter and length have 50% greater surface area and 45% greater weight than balls of the same material. In addition, they have 9% higher bulk density than steel balls, or 12% higher bulk density than cast balls. An important advantage of cylpebs over balls is that cylpebs produce narrower granulometric distribution due to their shapes. However, some discrepancies were found in the literature regarding the milling performance of cylpebs in comparison with balls (Chi, 2004). In recent studies, Chi (2004) has provided detailed information on cylpebs and has compared these to balls in relation to media mass, size distribution, surface area, and input specific energy. Ipek (2006) has investigated the effects of cylpebs and balls with equal mass and surface area on the breakage rate of quartz, using cylpebs and balls separately. Similarly, Lameck and Moys (2006) have investigated the effects of balls and worn balls on breakage rate of material using worn balls as grinding environment. However, no study has attempted to investigate the effects of grinding environment other than balls on the brekage distribution. As indicated by Prasher (1987), the breakage distribution function is independent of the following variables in ball mills: hold-up (Mika et al., 1967; Kelsall et al. 1969), mill speed and ball load (Herbst and Fuerstenau, 1972), media load and ball density (Kelsall et al., 1973), mill diameter (Malghan and Fuerstenau, 1976), and powder charge (Shoji et al. 1980). The aim of the present paper is to compare the effects of cylpebs and balls on the breakage distribution function of quartz with respect to same mass and same surface area. BACKGROUND Comminution as a rate process is called kinetic approach. Studies on the kinetic approach are reviewed by Oner (2001). Oner states that grinding kinetics are based on studies by Kolmogorov in 1941 and that Robert (1950) is the first to suggest this approach. Later, Melzak, Loeveday, and Reid have improved the grinding kinetics equation; and, Austin and Lynch have conducted two basic studies on the analytical solutions of these equations. Considering the results of studies comparing the size reduction mechanisms, it has been accepted that breakage constitutes of two operations. These two basic operations, first defined by Epstein (1948), are those of selection of material for breakage and the distribution of breakage material to particle sizes smaller than the initial size (Lynch, 1977). Epstein defined the two operations as: ? Pn(y), the probability of breakage of a particle size in the nth step of the breakage process. ? F(x,y), the cumulative distributions by weight of particles of size x<y arising from the breakage of a unit mass of a size y. Probability of breakage is called a selection or a breakage-rate function (Si). Characteristics size distribution after breakage is called a breakage distribution or appearance function (Bi,j). Due to the difficulties in representing particle size distributions mathematically and constantly, the batch equation based on particle size fraction is suggested. Thus, as is the case in breakage distribution and specific rate of breakage, the breakage parameters were defined by batch grinding experiments conducted in laboratories (Oner, 2001). When effective breakage occurs in the mill, the breakage of material with single feed size fraction usually fits first order grinding kinetics and the specific rate of breakage values can be calculated through the slope of semi-log plot. The values of the breakage distributions are deduced from the size distributions at short grinding times where there is mainly size 1 material breaking and only small amount of smaller sizes to rebreak (Austin et. al., 1984). B values can be calculated by using BII. [ ] where j is the top size of the charge, Pi(t) is the cumulative percent undersize of i th size interval at the short grinding time which gives no more than about 30% broken out of the top size interval. Cumulative primary breakage distribution, Bi,j, is also defined in an empirical form by [ ] where xi is the top size and Bi,j is the weight fraction of primary breakage products. The parameters F, ? and ß define the size distribution of the material being ground. On plotting size versus Bi,j on log scale, the slope of the lower portion of the curve gives the value of ?, the slope of the upper portion of the curve gives the value of ß, and F is the intercept as in Fig.1. [ ]

Jan 1, 2009