Search Documents

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By David Seymour

Precious metal producing mining companies in the United States, Canada, and South Africa were surveyed on carbon usage practices in the recovery of silver and gold. Responding companies represented CIP/CIL dperations, heap leach operations and combined mill/leach operations. Operational practices and carbon consumption rate measurements are presented, correlating consumption rates with process attributes. Precious metal producing mining companies in the United States, Canada, and South Africa were surveyed on carbon usage practices in the recovery of silver and gold. Responding companies represented CIP/CIL dperations, heap leach operations and combined mill/leach operations. Operational practices and carbon consumption rate measurements are presented, correlating consumption rates with process attributes.

Jan 1, 1992

By Jing G. Yen

When a solid-liquid mixture is conveyed through a pipe,' four hydrodynamic conditions may develop depending upon the properties of the transporting medium, the properties of the transported material, the properties of the pipeline and the flow characteristics. They are classified as homogeneous flow, heterogeneous flow, intermediate flow and saltation. Heterogeneous flow, which is the subject of the present analysis, occurs when solid particles are coarse, of high density, and the mean velocity of the flow is relatively low, such that the combination allows the establishment of a pronounced concentration gradient in the cross-section of the pipe. In this type of system the suspended matter does not change the rheological properties of the conveying fluid, and solid and fluid phases behave somewhat separately. In recent years much work has been directed toward gaining more insight into the hydrodynamics of heterogeneous flow (1,2,3,4,5,) However, almost all knowledge obtained is empirical in nature and limited in scope. Much effort has been extended to collect experimental information on the energy losses associated with systems of slurry flow (6-13) The work of Durand and Condolios(14,15) represents one of the most extensive experimentations in this field. Through systematic test runs, the effects of the major flow-parameters were studied one at a time. From the results, they concluded empirically that:

Jan 1, 1969

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a silver-white alkali metal that has recently become a target commodity for many junior mining companies. Lithium has a wide range of applications including ceramics and glass, lubricating greases, air treatment, continuous cast mold flux powders, polymer production, and primary aluminium production, but the current popularity of lithium can be attributed to an anticipated increase in demand for lithium ion batteries. The most common lithium-bearing minerals occur globally in pegmatites and granites. Spodumene [LiAl(Si2O6)] is the most desirable economic lithium-bearing mineral due to its high lithium content (theoretical Li2O content of about 8 wt%). However, lithium can also be hosted in petalite, micas, tourmaline, and phosphate minerals. In Canada there are a number of spodumene deposits in Ontario and Quebec at development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and use of electric vehicles. This paper discusses the beneficiation of hard rock lithium deposits, including an in depth review of the use of flotation to upgrade spodumene. A review of the use of dense media separation (DMS), magnetic separation, and roasting as means to process spodumene bearing ores is also discussed. INTRODUCTION Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35%), ceramics and glass (32%), lubricating greases (9%), air treatment (5%), continuous casting mould flux powders (5%), polymer production (4%), primary aluminium production (1%) and other uses (9%) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014). In the 1990s the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced over this period were consumed in the glass, ceramics and aluminium industries. In the 1980s and 1990s there were two major lithium operations in the United States: brine operations at Silver Peak, Nevada, and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, North Carolina. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994)."

Jan 1, 2017

By D. B. Gentzler, J. L. Kohler

A method of monitoring production information (raw tonnage and machine state) from each working section has been developed. The method is based on the sensing of electrical parameters in each section load center, and the reporting of this information through the existing mine-wide monitoring system. A decision-theoretic type of pattern classification technique has been used to define the machine states. The basis of the method is presented in this paper, along with a proposed hardware and software implementation scheme. Information issues central to the development and use of the proposed production monitoring system are also discussed.

Jan 1, 1990

By Nasri Munfah, Steffen Matthei, Vojtech Gall

"Conventional tunneling as defined by ITA WG19 is also known as the New Austrian Tunneling Method (NATM) or Sequential Excavation Method (SEM) was transformed in the US to deal with challenging tunneling conditions as an alternative to the more traditional tunneling methods. It is being used more often in urban areas, under difficult ground and ground water conditions, and with limited cover. Often the tunnel is of a large and non-uniform cross section in soft soils or weak rocks. The intent of using this tunneling method is to minimize impact on traffic and utilities and reduce disruption of everyday life of people and businesses. To meet these challenges, the industry developed technical approaches and implementation techniques and established sophisticated contractual relationships and collaboration in the field among various parties for successful implementation. This paper examines the development of conventional tunneling (NATM/SEM) in the US to deal with these challenges using recent examples such as Russia Wharf in Boston, Northern Boulevard Crossing, in New York, and Chinatown Station in San Francisco. INTRODUCTION / HISTORY Conventional tunneling or NATM/SEM is a concept that is based on the understanding of the behavior of the ground as it reacts to the creation of an underground opening. In its classic form the SEM/NATM attempts to mobilize the self-supporting capability of the ground to an optimum thus achieving economy in ground support. Initially formulated for application in rock tunneling in the early 1960’s, NATM has found application in soft ground in urban tunneling in the late 60’s and has since then enjoyed a broad, international utilization in both rural and urban settings. In the US the NATM/SEM tunneling method has been used successfully to address challenging tunneling conditions in urban areas. A large number of tunnels have been built around the world using a construction approach which was loosely termed NATM. During the years of discussions and the application of NATM a variety of terms have been used for the same construction approach. These terms were primarily aimed at describing the construction approach rather than the region of its reported origin."

Jan 1, 2016

By Steven B. Van Kouteren

Added value is a term loosely used in the industry, but what exactly does it mean? What does it take to make a value-added product and more importantly how does a company maintain the value added to its products? Most people agree that value-added means the value of a mineral minus the cost to produce it. But what is misleading is that producing value added products does not necessarily guarantee the profitability of the products. In some cases firms that make "value-added" products are not very profitable. It is not only important to understand how to make a value-added product but also how competitive forces in the market can erode the value added. Therefore, when we look at value-added opportunities, we must understand how to obtain the value added and more importantly how to maintain the value. There are four major factors that limit a company's ability to add value to its products. This paper will examine these factors and will use the ground calcium carbonate and mica industries as examples.

Jan 1, 1990

By J. Walden, S. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

By F. Segobia, M. Portal, F. Ysla, A. Mujica, L. Goicochea

The “Building Our Future” project is a collaborative initiative between the UNC SME Student Chapter and the Water and Earth Museum (MAT) of Asociación Los Andes Cajamarca (ALAC), both corporate entities of Newmont Yanacocha. Its mission is to promote responsible and sustainable mining among new generations while fostering a culture of equality and respect. This comprehensive educational program integrates sustainable development goals and includes workshops led professionals and external experts who share their personal stories to inspire students from rural and urban educational institutions to follow their dreams. Additionally, for this year 2024, the project development and implemented an interactive mobile application that educates users about the use of minerals in everyday life through four levels: Minerals in the Home, Minerals in Medicine, Minerals in Transportation, and Minerals in Agriculture. This multi-faceted approach seeks to raise awareness about the importance of mining in Peru’s economic, environmental, and social development, ultimately fostering a new generation of informed and engaged citizens who understand the vital role of mining in a sustainable future.

Feb 1, 2025

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By L. A. Roe

Calcium carbonate and talc fillers both find use in a multitude of Industries. Each filler has many commendable properties, and often compete for the same market. Quality controls for various grades are exacting and complicated. A detailed comparison of the physical and chemical properties of these two fillers is tabulated and the mining and processing of the ores is described.

Jan 1, 1980

By Alexander B. Ikonnikov

All known bauxite deposits in China occur in its eastern half, and almost all of them are found in the Carboniferous and the Permian. They are of platform origin, but contain diaspore as the major ore mineral. There is only one known deposit composed of gibbsite. The most valuable deposits are sedimentary ones formed in local depressions on the edges of platforms during marine transgressions. They lie on Upper Cambrian or Middle Ordovician limestone that was weathered for a long period of geological time. Generally, Chinese bauxites are low in iron, and have a rather low alumina/silica ratio.

Jan 1, 1984

By D. T. Hristopulos, A. Pavlides, C. Roumpos

In many of the lignite mines in Greece that supply the nearby power plants, the lignite deposits are multilayered and faults destroy the spatial continuity. This fact complicates lignite exploitation and the profitability evaluation of each layer. The location of a lignite layer could be so deep compared to other layers, that its exploitation would not be profitable. The purpose of this paper is the development of a suitable profitability index to help with the evaluation of the profitability of separate lignite layers. The definition of the profitability index is given and an algorithm is formulated that calculates the profitability index and evaluates whether each layer should be mined by comparison with a critical threshold value. The profitability index algorithm is applied to the multilayered lignite deposit of Amyndeo mine. It should be noted that the proposed index could be used in any kind of multilayered deposit, not just lignite.

Jan 1, 2011

By Richard F. Coon

Six potential locations along the west shore of Lake Mead were evaluated to site anew water intake pumping station for the SNWA. The evaluations were based upon geotechnical exploration results and conceptual intake pumping station designs. The exploration included geologic mapping, geophysical testing, underwater ROV inspections and borings. Ground surface and underground chamber pumping station designs were considered. Sites at Saddle Island, Black Canyon and Hoover Dam are geotechnically suitable. A Saddle Island site was selected because it has the most favorable conditions for the intake pumping station and the aqueduct to the Las Vegas valley.

Jan 1, 1997

By M. J. Laurila

Simulation of coal preparation circuits is becoming a widely practiced technique used for the design of coal preparation plants. On a much more limited basis, simulators are finding application in off-line process control. A typical application in the latter category involves inputting projected coal washability data for a shift into the simulator and using the software to optimize product quality and recovery within a range of predefined specifications. The plant is then operated at SG?s of separation determined from the simulation exercise for the one shift time period. This procedure is useful in that it incorporates some form of advanced planning into preparation plant operations. There is an attempt made to reflect changes in feed coal quality on a shift by shift basis rather than continually running the plant near design specifications with changes in SG?s of separation being made in response to an inadequate sampling program which only provides a spot measurement of material that has already passed through the plant. Instead of instituting changes on a shift by shift basis, NHI has proposed a method whereby monitoring three major operating parameters, * Feedrate to jig * Flowrate from hydrocyclone overflow * Density from cyclone overflow the ongoing plant operating performance can be accurately predicted on a continual basis, i.e., updated hourly. Using a distribution curve to predict the split between the clean coal and refuse from a given separator does not account for variations in efficiency that occur as a result of variations in operating parameters. NHI and Arch have studied the effect of both jig loading and solids content in the recirculating load to the jig on product quality. As a result, relatively simple measurements can be made on-line in a preparation plant which will provide input data to the simulation program that enables the prediction of jig/hydrocyclone circuit performance on a real time basis.

Jan 1, 1985

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009