Search Documents

By Howard W. Earnest

The Rio Blanco Oil Shale Company completed a modified in situ oil shale retorting demonstration at its Tract C-a Lease in the Piceance Creek Basin of northwestern Colorado during the spring of 1982. This demonstration was the first MIS project with shafts rather than adits for access to the mining operation, and it involved several potential hazards which required that particular attention be paid to mine ventilation. Methane was first encountered during shaft sinking and ultimately resulted in the mine being classified gassy by MSHA. Secondly, we encountered hydrogen sulfide in association with the ground water, and this proved to be a more persistent problem than did the methane. Thirdly, in order to burn the underground retorts, it was necessary to provide for potential leakage of retort gases and to obtain a modification to the MSHA standard which forbids fires under- ground. This modification had a significant effect on the ultimate ventilation procedures at Tract C-a. An extensive under- ground air monitoring program was included in the ventilation system.

Jan 1, 1983

By S. N. Chadha

INTRODUCTION The work described here refers to the Genesee River Interceptor Southeast Project. This project is a part of the Combined Sewer Overflow Abatement Program, Phase I, for the Rochester Pure Water District, Rochester, New York. Our contract required the design of a 13,200-feet long main tunnel, 14 feet finished diameter, approximately 100-120 Feet below ground; drop shafts and diversion tunnels to deliver surface flow to the main tunnel; a gate chamber whereby the main tunnel is dropped 35 feet, and provision made for connection to the future tunnel in Phase II, as well as a host of other surface structures. Cross sectional dimensions for the structures involved varied from 16 feet circular to a 20'x50' horseshoe, in a competent rock formation consisting of Lockport Dolomite and Rochester Shale. In the construction of a rock tunnel, the problems of the tunnel designers are as follows: 1. To evaluate stresses in the rock as a result of excavation. 2. Design a temporary support system to prevent any rock failure during the period of construction. Design of this temporary support system is empirical. Design loads given by empirical relations are dependent upon the rock quality and size of opening. Temporary support system may either be steel frames closely spaced along the length of tunnel and tied together, in the case of poor rock, or, an even spacing of rock bolts in the case of competent rock. 3. Design a final lining for the service loads. Service loads, in our case of a water-carrying tunnel, are hydrostatic pressure due to ground water, deadweight of lining) pressure of contained water and time dependent rock loading. The constitutive properties of the rock are extremely complex because of discontinuities, pre-existing stresses due to overburden, material symmetries and changes of initial state associated with the process of excavation. The changes of initial state may be changes of stress fields along with the consequent yield of the material or the extension of existing discontinuities.

Jan 1, 1977

By J. H. McNamara

A process has been developed for the successful hydrometallurgical extraction of copper from sulfide ores. The extracted copper in the form of a salt is converted by reduction to copper metal. Purification of the metal is described which includes a description of the casting of ETP quality copper wire bars.

Jan 1, 1978

By T. Rudolph, M. Pawlik, J. Benndorf, X. Yin, J. F. Brune, P. Goerke-Mallet

The long and often undefined period in the post-mining phase challenges geo-monitoring with its various responsibilities, like the detection of environmental changes, ground movements and water management. Modern methods of geo- and environmental monitoring observe numerous aspects using active and passive sensors with multispectral, hyperspectral and microwave sensors, with diverse spatial dimensions and spatiotemporal resolutions from satellites, Unmanned Aerial Vehicles (UAVs), in-situ sensors. Data integration, together with on-site knowledge and experience, provides the basis for comprehensive modeling, which improves the understanding of the environmental changes and their related causes, which is an essential step for public acceptance. In this paper, we aim to give a brief overview of various geo- and environmental monitoring methods.

Mar 2, 2022

By Walter E. Heinrichs

To many, petroleum exploration and successful geophysics , are partly synonomous, This is not because natural petroleum is usually concentrated as a liquid, nor certainly not because oil can be detected directly. The reason is Chat geophysics helps to at least better understand and sometimes, to even explain the essential geology involved. That groundwater is similarly a liquid with all but a few of its basic geologic relationships practically identical to petroleum, seems to have escaped many of those most interested and responsible for complete geo-hydrologic knowledge. The paramount need to use every means at our disposal for maintaining and expanding our crustal resources reserves are generally obvious, However, in view of the rapidly mounting requirements, continual re-emphasis is worthwhile.

Jan 1, 1963

By R. Schlüter

"The “Biohydrometallurgical Center for Strategic Elements (BHMZ)” is a cooperation of 13 departments of the Technical University Bergakademie Freiberg fostering interdisciplinary research along the whole (bio-) hydrometallurgical process chain to extract indium and germanium from sulphide ores. Research comprises methods to (i) bring the respective metal from the source material into aqueous solution and (ii) different approaches to extract pure metal or metal-containing materials from the solution. Within the BHMZ the Department of Underground Mining Methods deals with the design and implementation of an underground testing facility for bacterial in-situ stope leaching in its own “Research and Educational Mine”. The intention is to investigate innovative approaches for leaching technologies by crack initiation due to hydraulic fracturing or water pressure blasting under consideration of leaching kinetics and underground conditions. It is planned to set up two testing units comparing energy input and the metal output of conventional (blasting) as well as one of the innovative technologies. Aim of subproject is to establish an innovative and sustainable method ready for up-scaling. BACKGROUND Metals like copper and zinc mainly occur as sulphide ores in nature. Due to the insolubility of these sulphide minerals the respective metal is commonly extracted by pyrometallurgical processing methods. These methods require several steps of enrichment of concentrates such as flotation and roasting (Figure 1) under extensive energy utilization. Additionally, this arouses the emission of sulphur dioxide gas which can have a negative impact on the environment in form of acid rain, as long it is not caught by sulphuric acid facilities (Schippers et al. 2011). However, to treat the ore on the surface either open pit or underground mining operations are necessary. This implies operation steps from excavating, loading, and conveying/hauling, to dumping with the sub-processes crushing and stashing. Due to the tendency of increasing depth, more complex ores and decreasing ore grades of the mineable deposits as well as increasing energy and environmental costs these conventional mining and processing methods become in general more costly and difficult to apply. Hence, hydrometallurgical processes and especially the suitability of bioleaching as an alternative in-situ method for future mining projects should be examined. Leaching by means of microorganisms is a combination of mining and processing by converting the insoluble metal into an aqueous form. This technology is an economically beneficial and environmentally friendly alternative to pyrometallurgical processing methods especially for primary and secondary low grade ores. Mainly the extraction of copper but also of zinc and lead from sulphide ores is state-of-the-art in surface leaching operations like heap and dump leaching (Figure 1)."

Jan 1, 2015

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

The stability of surfactant-free foam films was studied using the thin film pressure balance (TFPB) technique. In pure water, it was not possible to produce foam films due to weak film elasticity and strong hydrophobic force. In the presence of NaCl, however, the hydrophobic force was sufficiently dampened to allow metastable films to form. At 10-5 M NaCl, the equilibrium film thickness reached a maximum of approximately 130 nm at pH 6.0-7.3. The thinner films obtained on either side of this pH range was due to the increased ionic strengths associated with the HCl and NaOH additions for pH control.

Jan 1, 2009

By Murray W. Hitzman

Two great revolutions in mining occurred during the 20th century. The first took place almost 100 years ago (1903-1905) with Daniel Jackling’s experiment in the economies of scale for large-scale mining at Bingham Canyon. Jackling’s ideas changed the focus of base metal exploration toward lower-grade, high-tonnage deposits. The second revolution was the impact of environmental and social concerns on mining. It started near the end of the 20th century and is still under way. This article speculates on the effects of this second revolution on the future of mineral exploration.

Jan 1, 2005

By S. E. Younis

The mining industry is currently looking to better understand, anticipate, and be able to mitigate business and operational risks in order to deliver the rewards of risk taking, and to minimize the frequency and impact of risk on the downside. Assessing risk works from the premise that the identification and management of existing risks can be very challenging, especially when threats are not easy to detect, the likelihood of occurrence is difficult to gauge, and/or the consequences are uncertain. Some approach this as a ?check the box? task, even though fire and safety incidents continue to occur and investigations often find the hazard analyses did not properly identify the cause or consequence. You cannot engineer protective designs and safeguards for causes and consequences that have not been identified appropriately. For the mining industry, risk management is an important tool for making critical decisions and, in some cases, meeting regulatory requirements. Providing high-quality documentation that meets both regulatory and corporate requirements is critical for maintaining safe, uninterrupted mining operations. Risk management is a five-part process: 1. Identify the hazards and their causes, 2. Determine the hazard consequences, 3. Calculate the frequency of occurrence, 4. Quantify the risk associated with the system, process, or procedure, and 5. Provide feasible solutions for the risks

Jan 1, 2012

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982

By William Gleason

"Mining roots run deep in Glenrock, WY, a town that was founded in part, because of the coal mining that began in the late 1800s. But that rich history also now threatens large parts of the town that were built over the top of the mines. Like many towns in the Western United States, mining is a proud part of the historical fabric and heritage of the town, but the legacy issues from past mining activities continue to present challenges to modern-day engineers.In the case of Glenrock, a small town about 40 km (25 miles) east of Casper, it is flooding from a century of water that has accumulated in the down geologic dip of the furthest northeastern extent of 87 ha (217 acres) of mine workings that has made the town susceptible to sinkholes and other issues (Fig. 1).Full commercial coal mining production began in Glenrock in 1887 during the development of the Fremont, Elkhorn and Missouri Valley railway. Due to poor overlying roof rock and continuous flooding within Glenrock, Mines No. 1 and 2 were fully closed in 1909. During its history, an estimated 87 ha (217 acres) were mined with 50 to 60 percent extraction ratio within the eastern town limits through room-and-pillar mining. It is estimated that the mines produced 22 kt/a (25,000 stpy) during their lifetime. A century later, the water pressure built up in the northeastern most portion of the mine has created serious concerns for residents.In 2016, the Wyoming Department of Environmental Quality’s Abandoned Mine Lands Divisions (AML) investigated a number of subsidence events in the town including sinkholes following heavy precipitation. The AML investigations confirmed that most events were related to the previous mining in the area.Mitigation efforts on the mines were done in the 1980s and 1990s, but the problems in the town and in a nearby subdivision persisted, leading the AML to search for alternative solutions."

Nov 1, 2019

By Jim McKinley

With a growing number of mines reaching closure and seeing closure costs materialize, regulators, lenders, and banks are observing projects that fail economically by miscalculating these costs. Mine closure costs are often categorized as a type of liability which is defined as the money owed by the company to offset effects from the project, and the money available to pay for those debts (e.g., bond). Often, decisions made before Day 1 of mining (e.g., co-disposal, dry stack tailings, waste segregation) can significantly change the bond calculation. Once the bond is calculated and funded, operators are encouraged to conduct closure research and use applied science for progressive bond release prior to final closure. However, this author has observed few instances of financially significant progressive bond release, as there are typically no robust procedures for bond return, either before or during closure activities. As a result, many companies decide that entering a state of Care & Maintenance (C&M) is less risky than attempting to fund closure activities with an unknown bond return mechanism. Although perhaps less risky in the short-term, the primary long-term risk with entering C&M is that it increases the chances of the bond not covering the cost of closure and the chances of the government/regulatory agency inheriting the mine closure. Bonds are typically reevaluated on a regular cycle (e.g., five years) so every mining company goes through this financing challenge eventually.

Feb 22, 2026

By H. Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in BOLTs) has been recently developed at McGill University. The device is essentially an alternative to the load cell, it permits the monitoring of bolt axial load in the field. The SAFEBOLT system consists of a portable readout unit, a connecting cable and the SAFEBOLT device, which is installed in the bolt head. The new device can be installed on any industry standard rockbolt or rebar. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electric wires. Pilot tests at two underground Quebec mines were carried out and helped improve the initial design of the device head.

Jan 1, 2002

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979

By Erich U. Petersen

Recognition of mineralogical and chemical zoning patterns associated with mineralization is an integral part of mineral exploration. Even though the origin of zoning may not always be known, zoning patterns as expressed by the systematic distribution of ore and gangue minerals, alteration or elemental assays (soil and rock geochemistry) have received much attention and are extremely useful in guiding exploration efforts toward locating economic mineralization. By contrast, the potential of using zoning information recorded in solid-solution minerals to address practical geological-engineering problems has received less attention. Solid-solution minerals can provide critical information for common problems faced in exploration, mine development and valuation. Mineral zoning information from solid-solution minerals can now be easily obtained because advances in electron microprobe instrumentation have made these instruments a most efficient, accurate, economical and practical tool for analysis of large numbers of samples. Now entire mines and districts can be studied in a timely and cost-effective manner as required by modern mineral exploration and mining practice. This article shows how knowledge of the composition of fahlore minerals can be used in addressing important problems in exploration, development and valuation. Situations are described in which drilling intersected "low grade zones" (Case one: Orcopampa, Peru, precious metal system) and where there was a need to determine the "lateral correlation of multiple ore intercepts" (Case two: Sheep Creek, Montana, sediment-hosted sulfide deposit).

Jan 1, 1992

By R. Codell, D. L. Hughson

While benchmarking the integrated finite-volume code MULTIFLO against the analytical solution of Philip et al. (1989) for cylindrical underground openings, we found numerical simulation of dripping threshold flux consistently higher than the analytical solution for both rectangular and unstructured grids. The magnitude of error is proportional to the alpha parameter characterizing capillarity. This may bias estimates of repository performance towards non-conservatism.

Jan 1, 2000

By Mustafa Kumral, Yuksel Asli Sari

Economic evaluations of underground mining operations are made based on the estimated or simulated grades of the block model as the actual values are not known. Depending on how the planning decisions are made, the risk of the operation can be managed and decreased. This research introduces a mixed-integer linear programming (MILP) model for stope sequencing optimization that considers the uncertainty associated with net present value (NPV) using chance-constrained programming (CCP). The introduced method permits achieving a balance between maximizing NPV and reducing the associated operational risk through transforming the problem into a multiobjective problem, where the objectives are maximizing the NPV and minimizing the risk. This risk is expressed in terms of the standard deviation of project outcomes, taking into account multiple possible scenarios. In a case study, the efficiency of the method was demonstrated as a decision-making tool capable of translating a specified risk or reliability level into a stope sequencing plan.

Jan 1, 2024

By D. Komljenovic, V. Kecojevic

Selection of the best possible truck type (model) is of crucial importance for the mine decision-makers. In this paper, authors contribute to the body of knowledge by developing a novel methodology for the selection of mining truck. Both the Coefficient of Technical Level (CTL) and Analytic Hierarchy Process (AHP) methods were used in this study. The CTL represents a mathematical function which takes into consideration the interrelations among the main technical parameters of mining trucks. The authors developed a hierarchical structure where both attribute categories and their importance, i.e. priority or weight in the selection process were determined. For each category, a number of sub-attributes and their priorities were assigned, and a pairwise comparison among them was performed using the AHP method. In the final part of the study, the CTL was integrated into the AHP and represents a holistic approach in the selection of mining trucks. A case study on 180 tonnes truck category offered by five manufacturers was carried out. A sensitivity study of obtained results was also performed indicating a very stable solution. The methodology presented in this paper may be used by mining operators to help in the selection of a specific type when acquiring a new truck. It may also be used by equipment manufacturers to help in analysis of potential benefits of envisaged modifications concerning an existing truck type and/or development of a new type.

Jan 1, 2007

By M. Adnan Goksel

The hydrothermal agglomerating process described (U.S. Pat. 3,235,371, (1966)) is different from the conventional high temperature processes. Green pellets or briquettes made with mixtures of moist iron ore concentrates and burned or hydrated lime fines are hardened in an autoclave at 198°C and under steam pressure for 1/2 to 5 hours, with or without previous drying. Under the neutral conditions, oxidation of magnetite does not occur as in the conventional processes. The resulting agglomerates are hard and resistant to abrasion and weathering, and they do not disintegrate in the Linder test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperature and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1968