Search Documents

By Frederick McNeill, Mahmood Khwaja, Benjamin Lundsted, David Polcari, Michael S. Schultz, Timothy Clougherty

The City of Manchester, New Hampshire, is embarking on one of its largest public works projects in history to construct a 12,000 foot long, large-diameter, conveyance tunnel through downtown Manchester. This area has challenging geology with undulating bedrock (granite, schist, and gneiss) profile overlain by fluvial deposits. Understanding the subsurface conditions is key to mitigating project risks, establishing plan and profile for the tunnel, and selecting the most cost-sensitive and technically appropriate tunneling method. This paper presents the project team’s approach for conducting the ground investigation, developing preliminary subsurface profile, and the considerations for selecting the tunneling method.

Jun 13, 2023

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By Jianmin Qin, R. V. Ramani

The major parameters affecting dust flow at a longwall face are dust generation rate, air velocity and quantity distribution at the face, and the characteristics of the dust such as particle size distribution, density etc. Previous studies have identified the longwall shearer as the major source of the airborne dust in the faces. In this study, the effects of dust generation rate and shearer speed on the levels of ambient dust concentration are investigated. A series of experiments were performed under controlled conditions in a full scale simulated longwall face at the Lake Lynn Laboratory mine of U.S. Bureau of Mines using characterized bituminous coal dust. A trickle-duster was moved up and down the longwall face to simulate the shearer. In each experiment, a known amount of dust was dispersed by the trickle-duster into the air and the average dust generation rate was calculated. At the same time, gravimetric respirable and total airborne dust samples were collected and air velocity measurements were made along the face. The experimental conditions, data, and results are presented and discussed in this paper. The airborne dust concentration and air velocity data indicate that the concentration increases and air velocity decreases with distance from headgate for the first half of the face. Towards the tailgate, the air velocity increases with increasing distance but the dust concentration levels off with some variations. The data show that a higher dust generation rate results in higher dust concentration levels. More importantly, the data show that the rate of increase of airborne dust concentration is higher than that of dust generation rate. For the same air velocity distribution and dust generation rate, lower speed of the dust source results in higher airborne dust levels at the face.

Jan 1, 1991

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Despite numerous empirical, numerical, and hybrid studies conducted on the subject of coal rib failure, mine fatalities related to rib failures continue to occur. To date, a standard methodology for the design of coal rib supports which can accommodate the wide range of unique conditions found in coal mines in the United States has not been developed, forcing mine operators to rely on the trial-and-error process or industrial legacy practices for the design of coal rib support patterns. In this study, to better understand the support systems' effectiveness, various rib bolting scenarios were investigated. A coal mass constitutive model is implemented to a Distinct Element Method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength-reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid Banded-Bright coal (BBC) were considered in this study. Different scenarios such as rib bolt length and the number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength reduction method in DEM code with the coal-mass model can aid in the development of practical primary support charts, which can help in the rib support design process. In addition, an unsupported RibFOS cutoff

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

"The Analysis of Retreat Mining Pillar Stability (ARMPS) program was developed by the National Institute for Occupational Safety and Health (NIOSH) to help the U.S. coal mining industry to design safe retreat room and pillar panels. ARMPS calculates the magnitude of the in-situ and mining-induced loads by using geometrical computations and empirical rules. In particular, the program uses the “abutment angle” concept in calculating the magnitude of the abutment load on pillars adjacent to a gob.In this paper, stress measurements from U.S. and Australian mines with different overburden geologies with varying hard rock percentages were back analyzed. The results of the analyses indicated that for depths less than 650 ft, the ARMPS empirical derivation of a 21° abutment angle was supported by the case histories; however, at depths greater than 650 ft, the abutment angle was found to be significantly less than 21°. In this paper, a new equation employing the panel width to overburden depth ratio is constructed for the calculation of accurate abutment angles for deeper mining cases.The new abutment angle equation was tested using both ARMPS2010 and LaModel for the entire case history database of ARMPS2010. The new abutment angle equation to estimate the magnitude of the mining-induced loads used together with the LaModel program was found to give good classification accuracies compared to ARMPS2010 for deep cover cases.INTRODUCTIONIn the early 1990s, the Analysis of Longwall Pillar Stability (ALPS) was introduced by Mark (1990) as a chain pillar design software and was generally accepted and used by the U.S. coal mining industry. Following the success of ALPS, the National Institute for Occupational Safety and Health (NIOSH) developed the Analysis of Retreat Mining Pillar Stability (ARMPS) program for designing retreat mining pillars using a similar approach as ALPS (Mark and Chase, 1997). The Australian mining industry also recognized the success of ALPS, and Colwell, Frith, and Mark (1999) calibrated the program to Australian conditions. The ALPS and ARMPS programs draw their strengths from the large databases that are used to calibrate them (Mark, 2009). However, following the Crandall Canyon Mine collapse in 2007, NIOSH had to reconsider the pillar design criteria used in deep-cover retreat mining (Mark, 2010). The ARMPS overburden load prediction algorithm was improved to more accurately predict the loading of narrow panels with high overburden depths by implementing the pressure arch concept, and this new version is called ARMPS2010."

Jan 1, 2019

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By Steve Trussell, William H. Langer

"Arizona aggregate (sand, gravel and crushed stone) producers enjoyed more than a half a century of nearly constant growth in demand for aggregates. Approximately 80 percent of the aggregate produced in Arizona is sand and gravel, and 20 percent is crushed stone (U.S. Geological Survey, 2015). Figure 1 shows the generalized distribution of potential sources of sand and gravel (yellow) and potential sources of crushed stone (other colors described below). Black dots show locations of aggregate operations.Sand and gravel commonly is produced from modern river channels and terraces although some alluvial fans and high-level paleo-river terraces also serve as aggregate resources. The gravel clasts are a mix of rock types that reflect the types of rock in the source area of the rivers. Generally processed river gravels meet stringent specifications for highend uses.Crushed stone, which makes up about 20 percent of production, primarily comes from a variety of metamorphic rocks and light-colored intrusive igneous rocks such as granite (brown areas), dark colored extrusive igneous rocks such as basalt and scoria (rust colored areas), and carbonate rocks such as limestone or dolostone (green areas). Carbonate rocks are also used in the manufacture of cement and lime.Construction and aggregate production in ArizonaBecause aggregate producers have limited facilities for storing product, stockpile changes are insignificant compared to production. Therefore, demand or consumption of aggregate in Arizona is considered to be equal to production. Production figures used in this paper reflect shipments, sales or marketable production, including aggregate used by producers to make readymix concrete and asphalt. Production figures were reported by the U.S. Bureau of Mines from 1950 until 1995 and by the U.S. Geological Survey (USGS) since then. Production figures are reported voluntarily, and major operators are the primary source for these figures. Because many smaller operators do not report their production, the figures are conservative values that provide an approximation of aggregates production activity."

Jan 1, 2015

By J. K. Lemley

The human element in large measure dictates success in contracting relationships. Because of our professional backgrounds, we view contracts primarily as either engineers, contractors or owners. A beneficial contractual environment--one in which decisions, risks and benefits are shared--demands equal consideration of all three points of view. Most of the older cities in the United States, for example, suffer from bad contracts--generalized, patched-together documents that represent an accumulation of modifications originally written to compensate for specific situations that have occurred over the years. Because such documents lack coherence, they often present conflicting instructions which lead to defensive, ultimately destructive attitudes among the parties involved in the day-to-day administration of the project. Good contract development begins with a strong central philosophy to which the details of the contract can be related. First, the owner should establish a comprehensive philosophy in which risks between the parties are identified. Following this, a specific contract document can be written to satisfy this established philosophy. The contrast between two opposed contractual situations, NYC Water Tunnel Number Three and the Seabrook Nuclear Power Plant Cooling Water Tunnels, illustrates how comprehensive, well-written contracts--contracts which share both risks and benefits--provide the basis for achieving quality construction that will reward engineer, contractor and owner.

Jan 1, 1983

By Wayne E. Kilker, Michael J. McBride, William P. Levy, Thomas J. Lamb

Between 1989 and 2004 the Massachusetts Water Resources Authority (MWRA)constructed several major wastewater and water tunnels associated with three major projects in the Boston area of eastern Massachusetts. There were many similarities and differences in the bedrock conditions encountered and among the contractual approaches for these independent projects. Through a clarification of the approach similarities and analysis of the contract differences, this paper addresses and presents what are considered to be valuable lessons learned. In doing so, the paper follows the evolution of such disparate issues as contract conditions, baseline reports and dispute review boards. The authors believe that the lessons learned even represent what, in certain cases, could be referred to as “universal truths” that are intended to have application to the next generation of tunneling contracts.

Jan 1, 2005

By Gerald G. Griswold, Allan G. Provost

INTRODUCTION The Norad Expansion Project was located 10 miles southwest of Colorado Springs, Colorado, within Cheyenne Mountain. The expansion areas to be excavated would be adjacent to the existing underground Norad complex, which would remain in operation during the work on the expansion. The original complex had been constructed approximately eight years earlier and had been in full operation for approximately five years. Phase I, Excavation was awarded the Tiro Construction Corporation, a subsidiary of Harrison Western Corporation, Denver, Colorado, in the fall of 1970. Notice to Proceed was given to Tiro on 28 December 1970. The project owner was the U. S. Air Force, design was performed by the U. S. Corps of Engineers, Omaha District, who would also serve as the construction agency. [ ]

Jan 1, 1979

By VIVEK KASHYAP, EVODY TSHIJIK KARUMB, PATRICK TAYLOR

Zinc ferrite is considered an integral phase of zinc residues as their presence can render the processing of zinc and critical metals difficult. It is a refractory phase, formed at high temperature in the presence of zinc (Zn) and iron (Fe) during oxidative roasting in zinc processing plants. Because it is refractory to efficient leaching, unreacted zinc ferrite gets concentrated in the final zinc residue, making it a viable source of zinc and indium extraction. The refractory nature of zinc ferrite makes the extraction of associated critical metals difficult. In order to explore a potential economic and carbon-neutral zinc ferrite processing technique, our previous study proposed the partial reduction of zinc ferrite followed by sulfuric acid leaching of the roasting product [1-3]. As demonstrated in our previous studies, partial reduction of zinc ferrite results in a mixture of ZnO, Fe3O4 and FeO, which can be further subjected to leaching for efficient extraction of zinc and critical metals such as gallium and indium.

Dec 1, 2022

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By William R. Yernberg

The 2003 Rapid Excavation and Tunneling Conference (RETC) was held at the New Orleans Marriott, New Orleans, LA, June 15-18. The New Orleans conference was the 16th since the RETC was formed in 1971. This year’s conference was sponsored by the Society for Mining, Metallurgy, and Exploration, Inc.(SME), with co-sponsorship of the Construction Institute of ASCE. Attendance at the meeting was 1,178, a conference record. This was up significantly from the771 attendees at the 2001 meeting in San Diego, CA. The RETC was formed to “advance the engineering and scientific knowledge of rapid underground excavation and tunneling through interdisciplinary meetings, publications, technical-educational exhibitions and encouragement of research.” The RETC conferences are now held every other year. They provide an opportunity for individuals to meet with designers, contractors and manufacturers associated with the tunneling industry to share experiences in all phases of tunnel design and construction.

Jan 1, 2003

By E. C. Westman, F. J. Shreve

This paper presents the design and construction of a multi-channel geophone array that improves tomographic imaging capabilities in both surface and underground mines. Especially important in the design of the array is sensor placement. Three issues related to sensor placement are addressed in this paper: 1) sensor placement in long, horizontal boreholes, 2) development of simple, robust, MSHA-acceptable clamping unit, and 3) orientation of the geophones within the borehole. Improved imaging capabilities will produce energy, environmental, and economic benefits by increasing exploration accuracy and reducing operating costs.

Jan 1, 2002

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By Giuseppe Gaspari, Xiangrong Wang

The pandemic emergency is forcing transit agencies to define strategies allowing social distancing, which are more challenging in underground interchange stations in crowded downtown cores. Toronto Transit Commission’s (TTC’s) Bloor-Yonge Station Capacity Improvement Project in Toronto was approved to meet increasing demand and represents an opportunity to fight COVID-19. This paper discusses cost-effective solutions in expanding the cut-and-cover station box over the existing Toronto Subway Line 2 and connecting it through ventilation openings in the cast-iron tunnel liner. Potential uplift risks and structural damage due to minimal vertical clearance were analyzed via three-dimensional finite element analyses with advanced constitutive laws to simulate the multi-stage construction process. Based on the simulation results, a series of countermeasures, including excavation support systems, king posts, ground-consolidations, and liner reinforcements were integrated into comprehensive design options to ensure the serviceability and structural integrity of the subway tunnels.

Jun 13, 2021

By R. Hogg, L. G. Austin, R. C. Klimpel

Slurry densities and holdup were measured for open circuit grinding tests in a laboratory overflow ball mill of 0.3 m diam by 0.6 m long, by emptying and drying after stoppage of the mill. Contrary to some other results in the literature, there was negligible variation of slurry level in the mill as a function of flow rate over a range of increase of flow rate of about 5 to I. However there was a gradual increase of solid holdup at higher flow rates because the slurry density in the mill increased. Equations are given for holdup and slurry density in the mill as a function of over flow diam, ball load, and feed slurry density. The average level of slurry necessary to give over flow was found to be much higher than that necessary to fill the mill to the overflow level at rest. The total level of balls and slurry was only increased slightly by ball loads higher than the overflow level. The overflow diam appeared to be the major controlling factor in determining the mill holdup.

Jan 1, 1990

By Jai Ghosh, Aprad E. Torma, Roger Guay

The catalytic effect of ferrous ion in the industrial biohydrometallurgical heap and dump leaching processes is explained. During the bacterial leaching of metal sulfides, ferric ion will partly be hydrolyzed and a variety of sols, gels, amorphous and/ or crystalline mono- and polynuc- lear hydroxo- and sulfato complex species formed, especially by olation and aggregation reactions. There are many problems associated with these iron precipitates especially in the purification of leach solutions. The present study will discuss the iron precipitation reactions; gives kinetic and thermodynamic evaluations of the effect of temperature on pyrite and ferrous iron oxidation; and reports on the tolerance of heavy metal ion concentrations by Thiobacillus ferrooxidans.

Jan 1, 1989

By S. K. Nandy, K. F. Unrug

The behavior of the immediate shaly roof within a drift mine in eastern Kentucky, operating in the Coalburg seam, was monitored with roof bolt dynamometers. The dynamometers used were capable of providing readings up to a maximum load of 66.72 kN (15,000 lbs), + 0.022 kN (5 lbs). To observe the influence of moisture on the rate and extent of roof deterioration, 57dynamometers were installed on roof bolts anchored in intake and neutral airways. Monitoring was conducted during the period January 1985 through January 1986, in order to cover a full cycle of dry and wet mine conditions associated with seasonal changes. Analysis of the data showed a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1987

By Jacques Villeneuve, Stéphane Brochot, Jean-Claude Guillaneau, Marie-Véronique Durance

Since 1986, BRGM has been developing a powerful process simulation software package, USIM PAC. These last years have seen significant developments in mineral processing technologies, particularly in hydrometallurgy, bio-hydrometallurgy and mineral liberation. The new version of the simulator, USIM PAC 3.0, incorporates these modem-processing fields. Its structure and tools allow the user to take into account, at the same time, a wide range of technological, economical and environmental aspects. The improvement of the existing features and the introduction of new unit operation mathematical models and tools such as the supervisor, global optimization, workshop model or chemical reactions contribute to a global approach in mineral processing design.

Jan 1, 2002