Search Documents

By A. J. Neale, B. C. Flintoff

A relatively inexpensive and reliable method of using liquid phase tracers to aid in the solution of material balance problems is introduced. The method is of value in situations where one is required to calculate a material balance around a process that has the operating appearance of a "blender" or "splitter" with respect to the available slurry sample data. The paper briefly reviews material balance development and tracer applications in mineral processing, introduces the problem to he addressed, and provides both theoretical and industrial evidence establishing the potential of the method.

Jan 1, 1987

By J. W. Craven, M. Katom, K. M. McCaffery

At Ok Tedi, ore type and SAG feed size distribution vary widely and frequently. This makes control of the SAG mills by application of the power/pressure relationship difficult. Power logic has traditionally been conservative due to power spikes associated with rapid size distribution changes. A new expert system was installed in early 2000. The system incorporates multiple state fuzzy logic to deal with frequent and radical ore type and size variations, along with monitoring of motor temperatures. A short term power spike no longer warrants immediate radical action. This has resulted in increased mill throughput and improved circuit stability.

Jan 1, 2001

By W. K. Summers

During the past few years monitoring systems have been installed to measure the effects of environmental changes on the ground-water resource. The design of a monitoring system depends upon the designer's perception of how the environmental factors merge with his perception of the ground-water flow system. The validity and representativeness of measurements made during a monitoring program depend upon the validicy of the designer's perceptions and concepts. To optimize the design of a ground- water monitoring program the designer should make preliminary measurements to confirm his assumptions.

Jan 1, 1985

This paper presents the results of a unique study conducted by the National Institute for Occupational Safety and Health (NIOSH) from 2016 to 2019 to evaluate the effects of longwall-induced subsurface deformations on shale gas well casing integrity and underground miner safety and health. At both deep and shallow cover instrumentation sites, surface subsidence measurements, subsurface in-place inclinometer measurements, and underground pillar pressure measurements were conducted as longwall panels were mined. Comparisons of the deep and shallow cover test site results with those from a similar study under medium cover reveal an interesting longwall-induced response scenario. Under shallow and medium covers, measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Conversely, measured vertical compressions under deep cover are one order of magnitude higher than those under shallow and medium covers. However, FLAC3D simulations of the casings indicate that, in all three cases, the P-110 production casings remain intact under longwall-induced deformations and compressions, which has serious implications for future mine design in areas where shale gas wells have been drilled ahead of mining.

Jan 7, 2020

By Jim Owens

The methodology of quarrying changed significantly in the Indiana limestone industry in the 60 years between Sept. 11, 1941 and Sept. 11, 2001. The former was the date of the Pentagon groundbreaking ceremony, while the latter was when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on Sept. 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction(and Indiana limestone) industry can accomplish when working toward a common goal.

Jan 1, 2005

By Jeff LeBlanc, George Gutierrez, Carl Pitzer

The Bay Park Conveyance Project was one of the largest microtunneling and rehab projects in the United States at the time of completion. The completed project conveys treated water from the South Shore Water Reclamation Facility located in Nassau County, New York, which currently discharges an average of 50 million gallons per day (MGD) of treated water into Reynolds Channel, to the Cedar Creek Water Pollution Control Plant (WPCP) ocean outfall pipe. The pipe carrying treated wastewater was installed approximately 20–60 feet below the surface. The treated wastewater is conveyed via microtunnel construction of a 2-mile long force main from the South Shore Water Reclamation Facility to an existing aqueduct under the Sunrise Highway, the rehabilitation of an 7.3-mile stretch of the aqueduct via sliplining, and construction via microtunnel of a 1.6-mile-long force main to connect the rehabilitated aqueduct to the existing Cedar Creek Water Pollution Control Plant (WPCP) outfall, which discharges and diffuses treated water three miles offshore in the Atlantic Ocean. This paper will review the Design-Build requirements, the chosen innovative solutions during planning for the micro tunneling portion of the project and review the microtunnel construction on the project.

Jun 23, 2024

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

Caterpillar said it will produce a Cat line of ac electric drive mining trucks. The world’s largest manufacturer of mining and construction equipment said the addition of an AC electric drive truck line will provide its customers with products to fit key applications. “We are very proud of the strong leadership position that Caterpillar has attained with its mechanical drive trucks, and we will continue to invest in strengthening that position,” said Chris Curfman, president of Caterpillar’s Global Mining Division and Caterpillar Inc. vice president. “We also recognize that there are unique applications that would make the addition of ac electric drive an important and attractive complement to our current truck line.” This is the largest investment Caterpillar has made in mining trucks in its history.

Jan 1, 2006

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant, able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). CN- + H202 => OCN- + H2O The most recent development, however, is the use of H202 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O2, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). 2 Au + 4CN- + 1 /2 O2 + H2O => 2 [Au(CN)2]- + 2 OH Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: • In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. • In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: • Hydrogen peroxide must be diluted before it is added to the pulp. • The dosage of H2O2, must be properly regulated based on the oxygen level of the pulp. • An important part of the continuous 02-control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1989

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987

By Yves Boissonnas, Marco Bettelini

"INTRODUCTION AND OBJECTIVES The operational safety of long and very long rail tunnels represents a key issue in all development stages, including design, construction, commissioning and operation. The spectrum of potential threats is very broad and challenging. These issues can only be mastered by means of a proper combination of a number of safety measures at various levels. This paper focuses on the specific safety issues and the extremely challenging conditions characterizing very long and deep tunnels. They include a significantly increased risk during operation that the incident train cannot exit the tunnel by its own means, long self-rescue and rescue distances, the presence of a number of trains, possibly mixed traffic as well as significant thermal issues. Amberg Engineering is strongly involved in the design and construction of most long and very long rail tunnels in Europe, including in particular the Gotthard Base Tunnel (GBT), Lyon-Turin Base Tunnel (LTF) and the Brenner Base Tunnel (BBT). The combined experience arising from these tunnels forms an invaluable body of expertise, which is summarized in this paper. The focus is on shared issues with practical relevant examples and project-specific solutions. Special attention will be devoted to the 57 km long Gotthard Base Tunnel, which will be operational by mid-2016 and will be the longest infrastructure tunnel worldwide. VERY LONG TUNNELS IN EUROPE Overview From the point of view of safety, tunnels in excess of about 20 km exhibit a significantly increased risk that incident trains could stop within the tunnel. This is related to the European Technical Specifications for Interoperability (TSI) on rolling stock, to be discussed in the chapter on rescue stations. This paper will specifically focus on the following longest tunnels in construction or operation, listed in Table 1."

Jan 1, 2016

By H. A. Kortmann

Blast furnace operators have been steadily increasing their quality requirements on burden material. These requirements include a high reduction rate of the ore burden as well as good strength at the beginning and during the whole blast furnace operation. Special requirements are made on the softening and melting behavior which ensures an optimal formation of the cohesive zone in the blast furnace. On the whole, the self-fluxed and olivine-based pellets meet these higher requirements due to their chemical composition, especially in the pure pellet operation. In the mixed sinter/pellet operation partly-fluxed and acid iron ore pellets can be appropriately used. The paper describes the demands on, and characteristics of, different kinds of pellets used in the Federal Republic of Germany.

Jan 1, 1989

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Paul C. Schmall, Lucian P. Spiteri, Arthur B. Corwin

Moving groundwater is generally recognized as the most adversarial condition for ground freezing. Moving groundwater can occur due to natural or man-induced groundwater flow, but either way may result in freeze formation difficulties. History has shown that if the condition goes undetected, catastrophic failure of the frozen shaft or excavation can occur. The success of ground freezing under potentially flowing groundwater conditions depends on an evaluation of the likelihood for this condition; an accurate and early diagnosis, with a careful evaluation of freeze pipe temperatures and piezometer water levels; and timely reaction to mitigate the possible delays. Successful remedial measures have included the reduction of ground permeability by modifying the soil properties between the freeze pipes with various kinds of grouting, or increasing the freezing effect by adding freeze pipes and/or the use of liquid nitrogen as the freezing agent.

Jan 1, 2007

By Don Phelps, John Hawley, David P. Field

In recent years observational techniques of tunneling have become increasingly popular methods to facilitate complex underground infrastructure projects. The traditional design and construction management practices developed in Europe have been adapted for application in North America to suit a more restrictive management and legal culture. This paper will discuss three recent projects, the San Diego Mission Valley East Extension, Washington Dulles International Airport People Mover, and the Seattle Beacon Hill Station and Tunnels, with the objective of identifying the challenges of applying observational tunneling methods to established contractual practices in North America.

Jan 1, 2005

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By G. S. Grainger, R. A. Cummings, F. S. Kendorski, R. L. Butts

Georgia Power Company's Rocky Mountain Project, located approximately ten miles northwest of Rome, Georgia, in the Valley and Ridge Physiographic Province, is a pumped-storage facility rated at approximately 800 megawatts of peaking energy. Geological field explorations and borings enabled the division of the rocks along the tunnel and shaft alignment into distinct lithologic units and defined the ground--water regime. Field explorations included a detailed analysis of the rock mass discontinuities at available rock unit exposures. Testing of rock strengths was performed in several phases in both the field and the laboratory. The field testing consisted of point-load testing, geophysical testing, in situ load testing, and hydro-fracture testing. Laboratory testing determined the Brazilian split-tensile strength, the unconfined compressive strength, the triaxial compressive strength, the joint-direct shear strength, and the pulse velocity. The rock mass along the tunnel and shaft was also characterized by empirical classification systems. The classification systems included the Rock Mass Rating (B1IR) and the Rock Mass Strength Determination (RHSD). The results of the field explorations, field testing, laboratory testing, and rock classifications were used to divide the rocks into two structural groups. These rock groups were defined as volumes of rock wherein the rock mass behaves similarly in response to the excavation. Each group, therefore, required separate rock engineering consideration.

Jan 1, 1986