Search Documents

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By Robert F. Jones

INTRODUCTION Upflow Solids Contact Clarification is a process long employed in the treatment of potable water, wastewater and municipal sewage. This process incorporated in a fiberglass conical structure seems to offer an economical solution to problems encountered in reduction of particulates in uranium effuents. CONCEPT OF UPFLOW CLARIFICATION Use of suspended solids contact units date back to the 1930's. These types of units produced by Infilco and the Permutit Company, among others, were used in the Lime-Soda softening process to precipitate calcium and magnesium salts from hard water. In general, the process operated as follows: (a) Raw water entered a central chamber where it was mixed with chemicals. The chamber had provisions for agitating and circulating the chemicals so that mixing and reaction zones were formed. (b) The water, precipitated chemicals, floc and turbidity flows to a clarification chamber (the Permutit precipitator used a truncated cone). In most cases the influent then passes upward through a blanket of suspended floc and other solids before it leaves the chamber at effluent weirs or launders.

Jan 1, 1984

By P. Eger

Minnesota contains a major low- grade copper-nickel sulfide resource within the Duluth Gabbro Complex. Several companies have actively explored this resource. Open pit mining would be required to develop portions of the resource, and as a result, large quantities of sulfide-bearing lean ore and waste rock would be stockpiled. Although the problems associated with high-sulfide tailings and acid mine drainage are well documented, the leaching characteristics of low-grade mineralized stockpiles must be understood for environmental impact assessment, siting, and planning. The Minnesota Department of Natural Resources and AMAX have cooperated in a research program to study leaching and revegetation -of test stock- piles, Six small (1600 'tons) stockpiles were constructed at the MINNAMAX Project Site and they range in composition from 0.29 to 043 g % copper, 0.075 to 0.09% nickel, and 0.6 to 1.45% sulfur. Two of the stockpiles were covered with mineral soil, one was covered with topsoil, and three were not treated Revegetation plots were established on the piles which received a soil cover. Leachate samples and flow measurements were collected at the base of the piles. Initial results indicate that metal concentrations in leachate samples range from 10 to 10,000 times the concentrations found in the streams of the area. During the first growing season, the test pile covered with topsoil yielded 30% less water than untreated test piles. No reduction in yield was observed for the piles that were covered with the less fertile mineral soil. First-year vegetative growth, expressed as biomass, was four times greater on the-topsoil pile than on the mineral soil piles. The long-term effects of vegetation on leachate quantity and quality continue to be investigated.

Jan 1, 1980

By Seung Han Kim, Andrew Yu, Carlos Jaramillo, Chu-Chieh Jay Lin

The Penstock Access Tunnel (PAT) concrete plug is a reinforced concrete plug separating the pressure tunnels from the personnel accessible tunnels and has leaked since the first filling at the Helms Pumped Storage Plant located in Fresno County, California. A grouting program was successfully implemented in 2009 to reduce the leakage from PAT concrete plug from over 1,000 gpm to 25 gpm. Recent observations indicated increasing water leakage through new pathways, leading to a decision to execute a high-pressure grouting and waterproof membrane installation program in 2017. The high-pressure grouting and membrane installation program was successfully executed in the areas adjacent to the PAT concrete plug where most of the inflows originated and the largest hydraulic gradients are suspected to present. It reduced the leakage from over 300 gpm of inflow to less than 20 gpm.

Jun 13, 2021

By James H. Vignos

An optical instrument designed for the on-line measurement of the size distribution of coarse particles (3-500 mm) being transported on a conveyor belt is described. Included is a discussion of the measurement technique, as well as test data verifying the legitimacy of the basic sensing approach. Field data indicating the instrument's ability to make useful measurements in an industrial environment are also presented. Applications in the mining and mineral industry, for which this instrument was orginally developed, are outlined, with particular emphasis given to the areas of crushing and grinding control.

Jan 1, 1979

By Chee Theng

"So many talks, so little time.One of the toughest challenges associated with attending the SME Annual Conference and Expo is deciding how to allocate one’s resources. After accounting for keynote and plenary sessions, committee meetings, networking events, luncheons and exhibits, attending even one of the 109 technical sessions and more than 600 technical paper presentations can be a labor of love. Many, however, managed to make it to many of the sessions, including the mineral and metallurgical processing technical session on solvent extraction, ion exchange and electrowinning.At one point, that room was seated to near capacity, with a considerable number of the audience members standing by the walls at the back. Brittany Valera of Freeport-McMoRan Inc. was one who came early and enjoyed the session in its entirety. "Everything was pretty exciting," she said. "I really liked the modular plants. I think the future of mining, just like what we talked about in there, lies in thinking about things like remote locations, lifetimes of plants, anything that would be reusable and sustainable; and lower-cost and user-friendly would be really beneficial."Michael Moats, associate professor of metallurgical engineering at Missouri University of Science and Technology, started off the session by presenting on behalf of post-doctoral student Alex Luyima, who, like many before him, had been snapped up by industry and is now working for a secondary-metals refining company in Texas. Their team studied the nucleation and growth mechanism of copper on stainless steel from synthetic acidified copper sulfate in the absence and presence of chloride ions and three commercial organic additives: Hydrostar 4208, DXG-F7 and Cyquest N-900. Currenttime data were analyzed using known models, with reference to scanning electron microscope images. Good agreement was achieved between the models and SEM micrographs of deposits at a commercially relevant current density of 30 mA/ cm2. The addition of 20 mg/L chloride was found to increase the size and reduce the number of nuclei. The addition of 2.5 mg/L of each additive did not change the mechanism, but all three reduced the size and increased the number of nuclei, leading to more uniform coverage of the substrate with smoother deposits produced in twohour electrowinning experiments. N-900 had the best deposition coverage while DXG-7 was the easiest to dissolve."

Jan 1, 2014

By D. Einarson, B. Strickland

The decision to accelerate development of Stillwater Mining’s East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and RailSystems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km(3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By D. R. Nagaraj

The chemistry and structure-activity relationships for four new classes of sulfide mineral and precious metals collectors developed recently are discussed in this paper. These collector classes are alkoxycarbonyl alkyl thionocarbamates and thioureas, dialkyl (or diaryl) monothiophosphates and dialkyl monothiophosphinates. The main emphasis will be to highlight the differences between collectors and their affinities for various minerals on the basis of data on kinetics of adsorption on pure minerals, natural ore flotation and microscopy of flotation concentrates. The mechanism of interaction of these collectors with sulfide minerals is also discussed with the available data on the FTIR and solution chemistry studies.

Jan 1, 1989

By J. L. Kearns

The importance of optimizing equipment replacement decisions becomes more critical each year due to the rising costs of buying new equipment versus maintaining old equipment. Replacing equipment when it is physically worn out, or replacing it too soon or too late relative to its Economic Life (when it is economically worn out), is very costly. After extensive literature review and research, Kennecott has developed its Equipment Replacement Guide (ERG) system which identifies, evaluates, and justifies the replacement of uneconomical equipment. The system considers such critical factors as inflation, decreasing work capability, increasing maintenance/repair and operating costs, taxes, time value of money, return on investment, salvage value, and investment tax credit. These factors are used in a system of equations which balance the costs of new equipment against the total operating costs of old equipment. The solution of the equations determines the Economic Life of equipment. Replacement of equipment at the determined Economic Life will earn the specified, required return on investment that is used in the calculation of the Economic Life.

Jan 1, 1979

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By G. L. Bloomsburg, E. G. Zahl

INTRODUCTION During the past decade, disposal of mine and mill waste material has become an increasingly important issue. Problems of structural stability and seepage effects on stability have been well addressed, and significant technological advances have been achieved [(1-4)]. The primary problem currently facing industry in the waste disposal area is environmental protection. The greatest environmental concern is over the amount of seepage or leachate entering the ground or surface water systems. Methods to determine the quantity of water seeping from a tailings pond have also been covered in the literature [(5-23)]. However, much further work is necessary to fully implement these techniques to evaluate tailings pond performance and accurately predict the various influences of disposal management on seepage from mill tailings. This study is an effort to develop those necessary techniques. The partially saturated method of analysis which is discussed here is applicable to most situations involving seepage from waste piles. In a conventional type of tailings pond, a slime layer is ordinarily built up under the ponded area. This material will consolidate slowly from capillary pressures and the weight of material deposited above it. In situations where this consolidation results in a slime layer of lower permeability than the native foundation soil, a partially saturated flow condition will usually exist in the native soil. This will result in a smaller quantity of water entering the ground-water system than would be predicted by saturated flow analysis. The finite-element program used in this study was originally developed by Neuman [(17)] and is called UNSAT2. The program will analyze problems of saturated or unsaturated, steady or nonsteady flow and can be used with a variety of boundary conditions such as constant flux, constant pressure, maximum flux, minimum pressure, and with infiltration, evaporation, and seepage surfaces. The maximum conditions are controlled by exterior factors such as atmospheric conditions; but the actual flow in the porous media is determined by properties of the porous media. In this test, the computer code was used

Jan 1, 1980

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has developed a laboratory apparatus for continuous separation of minerals according to their dielectric properties. The unit consists of a rotating wire grid drum electrode and a fixed curved wire screen electrode positioned 3 mm apart. By applying high voltage across the electrodes, which are immersed in a dielectric fluid medium, a high-gradient electric field is produced. The high-dielectric-constant minerals are attracted and conveyed through the separator by the rotating drum electrode, whereas the low-dielectric-constant minerals settle through the fixed electrode. In typical tests, a sample of Montana chromite ore containing 43 percent chromite was concentrated to 72 percent chromite with 90 percent recovery.

Jan 1, 1977

By Jerry M. Whiting

Greater awareness of the increasing need to develop supplementary energy sources is accelerating us towards many basic decisions regarding future utilization of mined energy materials -- uranium, coal, oil sands and oil shale. The latter material comprises a major potential source of oil which will require creation of unusually large and low-cost underground mining systems. In this paper, the author briefly outlines and analyzes several of the factors which continue to provide the somewhat unique character of oil shale nine planning and mine operation.

Jan 1, 1974

By J-P Strydom, J P. Z, S. Schafrik, M. Beck, Z. Agioutantis

Developing a method to accurately determine the weight and distribution of the load within a shuttle car bed eliminates the need for manual activation of the flight chain. Accordingly, this experimental study characterized the thermo-mechanical response of two unique load cells in force shunt, implemented as an engineering control to quantify load position and distribution without human intervention. The influence of environmental and installation conditions on the measurement accuracy was quantified and determined to be indirectly dependent on the characteristics of the material load cells that are mounted to.

Feb 22, 2026

By O. K. Kuznetzov, L. A. Otrozhdenova, N. D. Malinovskaya, I. I. Maksimov, N. D. Khodov

While processing zinc cakes with application of Weltz-technology silver remains unrecovered and goes into clinker. In order to prevent it the elaboration of effective silver recovery methods from zinc cakes before their weltzing becomes necessary. A combined method of zinc cakes treatment with leaching and flotation in a closed water circuit has been worked out. The technological scheme envisages the use of sulphgydril collectors in combination and comprises a series of consecutive operations: leaching, filtration, precipitation(cementing) and flotation. Total silver recovery is approximately 94%. The technology elaborated has been realized in a project by which the construction of a new shop is under way now.

Jan 1, 1995

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By M. A. Chandler, G. T. Adel, J. N. Richardson, E. C. Gutierrez

A rapid, bench-top analyzer has been developed to determine P2O5 content and CaO/P2O5 ratio in phosphate ores. The analyzer utilizes a portable computer equipped with a frame grabber to measure the reflective intensity (gray level) of phosphate samples placed in front of a television camera. P2O5 content is related to the average gray level of the sample, while CaO/P2O5 ratio is determined from the amount of bright material present. The sensor is currently being used to analyze flotation concentrate samples at Texasgulf's phosphate operation near Aurora, North Carolina. Sensor development along with results from laboratory and in-plant testing are discussed.

Jan 1, 1993

By L. Lichty

Treatment of refractory gold ores containing arsenic has always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries and production of hazardous fumes, effluents and residues. Due to these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processes for refractory gold ores and concentrates have been explored. A few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180° to 200° C or 356° to 392° F) and pressures (2.75 MPa or 400 psi) is accompanied by high capital and operating costs.

Jan 1, 1990

By S. C. Suboleski, J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later it will semiautomate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide the section foreman with real-time or near-real-time information about the performance of the loading and hauling units. This data will allow the section foreman to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and in-mine testing results from the first phase are now available.

Jan 1, 1994

By Michel Grenier, David A. Young, Brent Rubeli, Mahe Gangal

This work forms part of a study being conducted into the feasibility of constructing a prototype Load Haul Dump (LHD) vehicle for operation in underground Canadian mines. A series of in-laboratory assessments were performed to determine the relative contributions of a Deutz F4L912W (54 HP- conventional vehicle engine) and a Deutz F2L 2011 (31 HP hybrid vehicle engine) to diesel emissions concentration during mine transient duty cycles and steady-state operating modes respectively. Results indicate significant reductions in the quantity of gaseous and particulate emissions with the application of the hybrid system and a high-efficiency ceramic element filter. This paper describes the engine test protocols and the results of this laboratory study.

Jan 1, 2006