Search Documents

By G. B. Misra

Though installations of main mine fans vary widely, the commonest installation is of a surface exhaust fan connected to an upcast shaft some distance below its collar by a horizontal fan drift bending sharply. downwards near its junction with the shaft. The junction of the fan drift with the shaft often causes considerable shock pressure loss if not properly designed. In one of the major coal mines in India circulating 180 m3/s of air through the mine a pressure drop of 229 Pa out of the total fan pressure of 568 Pa occurred at this junction while in a smaller gold mine circulating 9.4 m3/s it was 147 Pa out of a fan-drift pressure of 382 Pa. With larger mines circulating larger volumes of air, ill designed fan drifts can lead to considerable wastage of the power of ventilation. Shock loss at the junction of fan drifts with exhaust shafts depends on (1) the angle of deflection of the bend, (2) sharpness of the corners (both inner and outer) at the junction, (3) the degree of contraction of the flow-stream which depends on the cross- sectional area ratio of the shaft and the fan drift as well as the amount of leakage through the shaft collar. It must be noted here that the friction pressure loss in the bend is negligible compared to the shock pressure loss.

Jan 1, 1980

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Ali Hafiz, Aidin Golrokh, Tom Iseley, Kaz Tabrizi, Saleh Behbahani

In the USA many highway tunnels were built during the 1930s through 1960s. This indicates that these tunnels have exceeded their intended design service life. Based on the initial tunnel inventory conducted jointly by the Federal Highway Administration (FHWA) and the Federal Transit Administration (FTA), more than 526 highway tunnels have been identified in the USA. For understanding the condition of the tunnels and risks associated with deteriorating conditions, comprehensive condition assessments are necessary to mitigate risk and remediate works as required. Monitoring the condition and rate of deterioration of tunnels is vital for timely tunnel maintenance and rehabilitation to avoid sudden tunnel collapse. This session will explain the necessary steps for tunnel inspection and review some of the state of the practice information on tunnel inspection techniques.

Jun 13, 2023

By Howard L. Hartman

To concede that I am the most surprised - not to mention the least likely - recipient of the Daniel C. Jackling Award is a true confession I must share with you. Quite honestly, I've asked myself, "Why me?" The Jackling Award has a well-deserved reputation of being a practitioner's, a doer's, a CEO's award - not kudos for a retired school teacher! While at least five of the previous recipients have taught in universities, to my knowledge I am the first to earn the award for "alleged" academic accomplishments. It is humbling enough to keep me livable for a long time. If you glance over the roster of Jackling Award lecture topics, you will spot another anomaly: The lectures last year and this deal with the subject of education - the only two in the 37-year history of the award. The two complement one another rather well, too, C. Allen Bom of Amax addressing critical needs of public education, while I am going to look at the post-high-school years. But I want to focus on more than engineering education. The training role of industry - the principal consumer of our product-also warrants examination. As I hope to establish, there is something unique about mining engineering - education and practice - that is both strength and weakness. We need to recognize that, if we are to cope with the weaknesses in order to capitalize on the strengths. We look at five premises that relate to the uniqueness of the mining engineer and his or her preparation for a professional career.

Jan 1, 1991

By James Whitlock, Michael Robert Wilcox

The volume of recently published material in praise of various refractory gold ore treatment methods is impressive. The authors are unfailingly bright, focused and thorough, and as each paper concludes, the reader is tempted to abandon other methods and embrace this truly better way. But there are many "better ways," many different ores, many different environmental requirements and many differ­ent economic circumstances. As we approach each set of cir­cumstances, it would be useful to have an objective way of comparing various methods in order to identify the most promising approaches. This discussion attempts to provide that.

Jan 1, 1991

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that, overall, the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In common practice, however, coal blending is at best coal mixing. If necessary, more sophisticated blending systems can produce a more homogeneous feed by using accurate weighing devices and on-line coal analyzers coupled with sampling systems. Blending can be accomplished at the mine, on stockpiles, and from bins, bunkers, and silos.

Jan 1, 1994

By D. A. Newman

The accurate prediction of mine profitability is essential for success in the present minerals market as is the ability to quantify the influence/of variations in revenues and costs on cash flow. A menu based spreadsheet template has been developed to determine annual cash flow, maintain depreciation schedules, and estimate labor and operating expenses. Sensitivity analyses may be conducted to determine the effect of productivity upon mining costs and the effect of selling price escalation upon rate of return. The advantage of this approach is that it can be used by a wide variety of professionals without extensive computer experience.

Jan 1, 1988

By B. A. Ashley

Rosebud Mining Co. (RMC) is based in Kittanning, PA. As of October 2013, it operated 24 active underground mines in Pennsylvania and Ohio. RMC?s Tracy Lynne Mine is located approximately 5 km (3 miles) east of Apollo, PA, (approximately 48 km or 30 miles northeast of Pittsburgh, PA) and mines the Lower Kittanning coal seam. The coal seam averages approximately 1.1 m (45 in.) thick and is of steam coal market quality. The mine is a single unit operation. Coal is mined using a continuous mining machine and is transported from the face to the conveyor belt using a continuous haulage system. Typical ventilation in the mine consists of an exhausting fan that draws air through isolated intake, belt and return air courses (Fig. 1).

By Marcel F. DeGuire

Pilot plant operations are described for the treatment of manganiferous zinc concentrates from the Gamsberg ore deposit in South Africa via conventional electrolytic zinc processing. Two methods were employed for the control of excess manganese ions in the pilot plant electrolyte involving (1) chemical oxidation and (2) anodic oxidation. The chemical oxidation method for manganese control was very successful. It also was found that the addition of manganese dioxide ore was not required for oxidation of ferrous iron during the neutral leach or jarosite precipitation steps. A new method (JAR process) for iron removal also was tested in the pilot plant.

Jan 1, 1978

By R. L. Murray-Smith, M. E. A. Robertson, M. J. Prosser

The AZTEC is an automated instrument, for the non-destructive analysis of gold ore samples, which uses energy dispersive X-ray fluorescence (XRF), This is achieved by X­ray tube excitation of gold K X-rays. The first production instrument was commissioned at Vaal Reefs Chemical Laboratory (VRCL) in November 1987, followed by two second generation instruments in 1989. AZTECs have also been installed at Western Deep Levels and at Anglo American Research Laboratories (AARL). A further unit is being assembled at Ashanti mine, Ghana. At VRCL the AZTECs are used primarily for the evaluation of mine (stope) samples. Each of the production instruments can routinely analyse 650-700 samples per day, with the aid of a robotic sample transfer system. Various techniques have been evaluated for increasing sample throughput. For example, higher value samples can be counted for a shorter time to obtain the necessary relative precision.

Jan 1, 1991

By S. Chander

The effect of pretreatment potential on the response of a gold electrode for Eh measurements in sulfide solutions was examined in terms of measured Eh values and electrode response time. The electrode response time is defined as the time required for the electrode to reach a steady-state value. The relationship between measured Eh values and the hydrosulfide ion concentration is established. The effect of pH, the reversibility of the gold electrode in the sulfide solutions, and the reproducibility of measurements are also investigated. A mixed potential theory is proposed to explain the observations.

Jan 1, 1989

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By Paul Soros

Lord Robens, Chairman of the National Coal Board of England announced recently to the world press plans for construction of the largest bulk terminal in Western Europe. This should result in annual freight savings of 22.4 million dollars and between 150 and 190 million dollars of new export business. These are rather substantial amounts for any mining enterprise. Or to put it another way, opportunities to make substantial savings in the delivered price of a highly competitive commodity such as coal are few and far between. One area where such opportunities still exist is in the economical; movement of bulk materials between producer and consumer.

Jan 1, 1966

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By Anthony Peach, Lok Home

Introduction Raise boring is the most accepted form of mechanized hard rock boring in the mining industry. It appeared logical to take this mechanization one step further by introducing computers. Atlas Copco Jarva has produced a series of raise boring models that use an integrated computer. The company decided to use electronics and computerization, not for marketing purposes, but to make its equipment more cost-effective. Basis of Cost-Effective Design From the manufacturer's standpoint, it is possible for the equipment owner to reduce the cost of putting in raises by: • Replacing existing components with less expensive components that produce the same results; • Replacing existing components with more expensive components that make the equipment more productive; • Mechanizing equipment to reduce associated labor costs; and • Combining the above. Analysis of a standard raise boring machine (RBM) system showed that little could be done with less expensive components. It appeared, however, that the RBM could be more productive by transmitting more horsepower through the expensive drill string, while being precisely controlled by computers. An RBM system includes a basic machine, drill pipe, accessories, reamer, and cutters. The approximate percentage cost of various components on a standard system capable of boring 300 m (985 ft) long and 3-m-diam (10-ft-diam) aises in medium to hard rock is shown in Table 1. Also shown is the increased cost above standard of the Jarva computerized machine, and the productivity of both. Increased Productivity Penetration is important during the reaming cycle for more productive raise boring. This is possible by increasing the cutter load with constant rpm or increasing the rpm with constant cutter load. To increase thrust and maintain rpm requires increased capacity in the cylinders, drive train, main thrust bearings, drill string, electrical motors, and power units. To increase rpm and maintain cutter load requires only increased capacity in the electrical motors and power units. This is possible because the torque requirement remains constant for a constant thrust load. Only the horsepower increases, proportional to rpm. Since cutter costs are a big factor in raise boring, changes in machine performance must be analyzed to assess the effect on cutter performance. With a standard or typical carbide cutter, as used on raise boring machines, the effects of increased thrust or rpm are shown in Table 2. The assumption is made that the base data is the current rpm and thrust range where the cutters are now operated. It is also assumed one variable is held constant while the other increases. The result of this comparison, approximately, is that a 50% penetration increase can be achieved with little or no increase in cutter cost if rpm is increased 50% and cutter load is maintained constant. A similar 50% penetration increase can be achieved with a 45% increase in cutter cost, if the cutter load is increased by 20% and maintained constant. From an equipment standpoint, it is significantly less expensive to increase rpm 50% than it is to in-

Jan 7, 1984

By Greg T. Saretzky, Wilson G. Ward

A comprehensive hydrologic study was completed far the waste rock dump at Equity Silver Mine, BC. Characterization of the hydrologic system included geologic structure. topography, surface hydrology and groundwater systems. The results of the study conclude that the cover system is restricting net infiltration to approximately 5%. However, significant discharge continues to occur from the perimeter of the dump. A three dimensional seepage analysis was carried out to illustrate the influence of groundwater discharge associated with the regional topography and geologic structures. The results of the modelling program show that groundwater discharge occurs from the waste rock dumps when high recharge rates are specified for the surrounding topography- This groundwater discharge strongly influenced by the high hydraulic conductivity assumed far the fractured bedrock. The modelling results are considered preliminary and field drilling and piezometer installation is being conducted to determine the groundwater regime in the vicinity of the waste rock dump.

Jan 1, 2000

By Ralph T. Buscarello

For practical purposes, the terms "natural frequency," "resonance" and "critical speed" are synonymous. A part passing though its "critical" or "critical speed" may also be said to be "resonant" or "resonating." The vibrations of a precisely balanced part can be magnified by the structure in which it is assembled. Anyone who has driven an automobile knows that it will vibrate more at a certain speed than at others. According to the formula for centrifugal force, vibration should increase steadily with a rise in rpm. What happens instead is that the vibration not only in- creases with r m. but suddenly rises at a much higher rate through the critical speed, and then apparently smooths out as the rpm passes beyond it. To visualize what happens, consider a simple flat spring with a weight mounted at one end. When the spring is deflected by pulling down on the weight and then letting it go, the spring will oscillate, and the spring-and-weight system will vibrate at its natural frequency. If the timing or direction bf the impulses imparted to the spring did not coincide with its natural frequency, the result would be an irregular vibration that would not build up. If, on the other hand, the timing and direction of the impulses did coincide with the spring's natural frequency, the result would be a larger and larger amplitude. If the impulses were continued indefinitely, the amplitude of the spring's vibrations would go on rising [while its frequency stayed the same] until the spring broke or the amplitude of the vibrations reached an equilibrium [because frictional or other forces would tend to damp it]. Resonance magnifies the amplitude of vibrations in a relatively undamped system between 100 to 200 times over that of nonresonant vibrations. Frictional or viscous damping often reduces the magnification [from 10 to 20 times], but even with this reduction the amplitude would still be large enough to cause excessive wear, and sometimes even fractures. For example, a blower might show only 0.001 in. of vibration on the manufacturer's test stand. Installed, the blower could pass into its critical speed [the speed at which the frequency of the vibrations caused by the rotor coincides with the supporting structure's natural frequency], and the 0.001 in. of vibration could be resonated to 0.010 in., or as much as 0.020 in. The cure for such a condition would not be to lower the vibration of the blower by further balancing or better alignment but to separate the two frequencies by at least 20 to 30%.

Jan 1, 1970

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The paper investigates the influence of slope height, slope angle, slope material, and rock size on rockfall runout distance in openpit mines. Using statistical analysis and simulation, the study aims to improve rockfall hazard assessment and catch bench design by identifying key variables affecting rockfall behavior.

Oct 1, 2023

By John Murray, Ryan Smith, Daniel Ebin, Robert Gould, Thomas Hennings

The Atlanta Plane Train Tunnel West Extension was excavated at Hartsfield-Jackson Atlanta International Airport using Sequential Excavation Methods (SEM). At its shallowest point, tunnel cover to bottom of Domestic Terminal footings was limited to 6 feet in soft ground. To mitigate risk of excessive building movement due to tunneling-related activities, the columns near the alignment were directly underpinned. Underpinning was accomplished using a combination of grouted mini-piles, installed under low headroom conditions, that supported steel framing spanning over the tunnel excavations. This paper focuses on design and construction of the underpinning system used to mitigate risk from tunneling.

Jun 13, 2023