Search Documents

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Saied S. Navid, Michael A. Piepenburg, Richard F. Escandon, Robert C. Lindsay

INTRODUCTION Phase I of the Los Angeles Metro Rail Project, known as MOS-1 (Minimum Operable Segment-1), is the first phase of the 27 km± (17 mi) subway starter line. MOS-1 is currently under construction and involves approximately 6.4 km (4.4 mi) of subway, five stations, yards and shops routed through the downtown area of Los Angeles. The project will form the initial heavy rail backbone of a more extensive light and heavy rail transit system planned for the greater Los Angeles area in the future. Construction Contract A-171 is one of 4 tunnel contracts within MOS-1 and involves construction of twin tunnels running from the downtown metropolitan area west to MacArthur Park. The heavily populated and developed downtown area, potentially gassy ground conditions, and the possibility of undocumented abandoned oil wells in seismically active southern California made the design and construction of Contract A-171 a uniquely interesting project. This paper summarizes the construction history to date (December, 1988) including design geotechnical considerations, tunnel support design, as-built geologic conditions, shield tunneling performance through soft ground, and ground response. The findings presented herein may aid in the design and construction

Jan 1, 1989

By Edward Finch, William F. Riggs

Selectivity and recovery of many industrial minerals can be directly affected by the carbon length, degree of unsaturation, and melt point of fatty acids used as collectors. Examples of several modifications are provided based on actual experiences of commercial applications. A review of recent history indicates that fatty acid collectors are applicable from C9'C18 in carbon length, however, not for all minerals. The mesh size, density, and surface characteristics of the particular mineral, as well as other related operating conditions, are important in selecting the correct fatty acid configuration. A review of some past programs are submitted as a guideline in the selection of fatty acids and supported by isolated, successful examples demonstrating the effect of carbon length and unsaturation.

Jan 1, 1986

By R. Hildebrandt, K. Cybulski, G. V. Goodman, Z. Dyduch, M. L. Harris, M. J. Sapko

Past research showed that bituminous coal dust remains dry and dispersible in the presence of moisture. Rock dust must disperse with the coal dust to effectively inert a propagating coal dust explosion. Non-treated rock dust readily absorbs moisture, limiting its dispersibility, while anti-caking treated rock dusts can remain dry. The National Institute for Occupational Safety and Health contracted the Central Mining Institute in Poland to conduct large-scale testing in their Experimental Mine Barbara to determine if a treated rock dust can be as effective as non-treated rock dust in attenuating or quenching coal dust explosions under the same experimental conditions. INTRODUCTION One of the goals of the National Institute for Occupational Safety and Health (NIOSH) is to conduct research to reduce the risk of mine disasters and provide workplace solutions to reduce the risks associated with accumulations of combustible and explosible materials; the most common form of which is the generation of coal dust during the mining process and its subsequent distribution downwind. Dispersible rock dust is a primary defense for preventing coal dust explosion propagation in underground coal mines, and its properties are defined in 30 CFR 75.2. “Pulverized limestone, dolomite, gypsum, anhydrite, shale, adobe, or other inert material, preferably light colored, 100 percent of which will pass through a sieve having 20 meshes per linear inch and 70 percent or more of which will pass through a sieve having 200 meshes per linear inch; the particles of which when wetted and dried will not cohere to form a cake which will not be dispersed into separate particles by a light blast of air; and which does not contain more than 5 percent combustible matter or more than a total of 4 percent free and combined silica (SiO2), or, where the Secretary finds that such silica concentrations are not available, which does not contain more than 5 percent of free and combined silica.” An earlier NIOSH investigation of rock dust revealed two significant concerns with the supply of rock dust to U.S. coal mines: 1) insufficient particles <200 mesh (75 μm) and 2) all rock dusts when wetted and dried formed cakes and were not easily dispersed with a light blast of air (1). Past research by the U.S. Bureau of Mines and others showed that bituminous coal dust remains dry and dispersible in the presence of moisture (2). Rock dust must also be dispersible in concert with the coal dust to effectively inert a propagating coal dust explosion (3, 4, 5, 6). Non-treated rock dust, however, readily absorbs moisture, limiting its dispersibility, while a rock dust treated with long-chain fatty acids (such as stearic acid) can remain dry and dispersible. Stearin-treated rock dust has been used in British coal mines (7) and is commonly used in Polish coal mines.

Jan 1, 2019

By Kalliat T. Valsaraj, Louis J. Thibodeaux

A mathematical model is described for the transfer of hydrophobic compounds from aqueous to an immiscible organic phase using fine bubble aeration; the process otherwise known as "solvent sublation" an adsorptive bubble separation process. The limitations of the model are explored by simulating experimental results both for a batch scale process and a continuous process. The qualitative predictions of the model with respect to the influence of the organic layer (mineral oil) are tested by performing experiments using chloroform and 2,3,6-trichloroanisole as hydrophobic compounds in the aqueous phase. The continuous process is seen to be limited by the requirements of fine bubble generation and the ratio of influent feed rate to air flow rate.

Jan 1, 1989

By M. Laliberte

Gold mine effluents are often characterized by a high concentration of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While non-acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be non-lethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25 C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.

Feb 23, 2014

By Morley H. Mathewson

The unprecedented demand for capital investment in the mining industry today has intensified management&apos;s interest in every known technique which will help to reduce operating costs and increase production. One proven approach leading to the accomplishment of this objective is well known in the mining industry and is gaining added prestige, particularly where keen competitive conditions exist. This approach is in the area of incentives applied to mining productivity. An investigation of many incentive plans now in use throughout the mining industry revealed a predominant number of conventional type plans, Most of these plans are designed to reward the hourly-paid employee on the basis of percent over and above a standard hourly or daily ton rate, By contrast, this search failed to divulge any incentive plan solely and independently developed for production management employees. This does not mean that such plans in the mining industry are nonexistnet, but it does indicate that production management incentive systems are scarce or are being kept under wraps.

Jan 1, 1960

By V. J. McSweeney

This paper is directed at interested parties outside the Beach Sand Industry : the scope is quite broad. The geomorphology described is a successful working hypothesis which guided the author during prospecting and pegging campaigns : the author is not an expert in this field. The test data used in the text, for illustrative purposes, is original and may constitute a contribution to the state of the art. The operation- al and design philosophy embodied in the text is personal and describes the author&apos;s methods : all practising exponents would differ in some degree amongst themselves on these subjects. In this paper, no criticism of any existing operation or brand of equipment is intended and names are used to maintain a real contact with the subject matter. The author believes that the operational and design techniques evolved in the Beach Sand Industry under continual duress, have a wider application in the mining industry. This glimpse of the Industry is intended to enhance the respect for the present and past members. Space does not permit individual acknowledgements.

Jan 1, 1982

By C. Abbruzzese, L. Piga, P. Fornari, S. Ubaldini, R. Massidda

The effects of certain variables on the extraction of gold by thioureation have been investigated on a quartzose gold-bearing ore using a statistical multifactorial strategy. The factors taken into consideration were milling time (which corresponds to a given grain size), oxidant concentration, thiourea concentration and liquid/solid ratio. The influence of these four variables was ascertained first by a full factorial design at two levels for each variable (16 runs). This permitted the estimation of first-order effects of the factors affecting the process. Then 9 runs were added whose levels were both in the centre of and outside the axes of the previous plan thus originating a central composite design. This permitted estimation both of second-order effects of the factors involved and of parameters of a second-order polynomial model. The results show that extraction of gold depends only on milling time and oxidant concentration, at least in the experimental range considered. The equation fitting experimental data, as calculated by the least squares method, allows a response surface to be drawn. Due to the low gold grade of the ore (6 ppm) statistical analysis could lead to contradictory results, hence strict observance of Gy&apos;s rules for sampling and very accurate and precise chemical analyses were required.

Jan 1, 1995

By Allan G. Provost

Shaft construction is assuming ever increasing importance when new mining enterprises are considered. The reasons for this increased emphasis is the much greater depths at which many new ore-bodies are being developed and the rapid depletion of near surface reserves requiring mines to go to greater depths on existing deposits. These greater depths increase the probability of exposure to unfavorable geologic conditions and it is more likely that high ground and/or water pressures will be experienced at these depths. The large capital costs involved and the critical position of a shaft in the overall mining program necessitate that this element of project development be given careful and critical consideration. The Henderson No. 2 Shaft is located in the Rocky Mountains of north central Colorado (See Figure I), about 55 miles west of Denver, near the community of Empire in Clear Creek County. At the 10, 442 foot collar elevation, winter arrives in late September and brings snow to contend with until May. The labor force for Shaft No. 2 is approximately 90 men. They are provided access to the project via all-weather U. S. Highway 40. SHAFT DESIGN The Henderson No. 2 Shaft is a 28-foot I. D. circular, concrete lined (1 foot thick) vertical shaft. The final depth will be approximately 3100 feet

Jan 1, 1972

By David Field, David Powell, Richard Hulsen

The Mission Valley Light Rail will loop through San Diego State University (SDSU)and to minimize the impact of construction most of the works will be underground. The project will require construction of a 330-m long (1080-ft), 11.24-m wide (36.9-ft),single twin track tunnel through Stadium Conglomerate, a poorly cemented dense sandy gravel with cobbles. Key technical issues are discussed including the ground conditions and predicted ground response, the use of sequential excavation methods to control deformations and specific construction concerns such as instrumentation and monitoring. Management of the construction process to minimize risk is particularly important in this environment and the strategy selected to control the works is also considered.

Jan 1, 2001

By Fathi Habashi

WHILE HYDROGEN SULFIDE precipitates metal sulfides from aqueous solutions, other gases such as sulfur dioxide, carbon monoxide, and hydrogen, under certain conditions, precipitate the metals directly. This can be achieved at high temperature and pressure. Such processes are of great technical importance, since metals of high purity are precipitated economically in a powder form. As a result of the availability of such powders on a large scale. processes for compacting metal sheet and other mill forms directly from the

Jan 1, 1970

By W. C. Hirt

Deposits of ferromanganese crust containing cobalt and nickel occur on the seafloor in the Pacific Ocean near the Hawaiian Islands and Johnston Atoll. This paper describes developmental flotation metallurgy to separate crust from its associated substrate gangue. Important variables in ferromanganese crust flotation include reagent type, aeration rate, conditioning time and agitation intensity, pH, temperature, water type, and feed size distribution. Flotation in seawater of minus 600 ~m (-28 mesh) material assaying 6.2% Mn, 0.2% Co, and 0.13% Ni with diesel fuel-crude tall oil-sulfonate collectors produces concentrates assaying 15% Mn, 0.6% Co, and 0.3% Ni with recoveries of 89-95% while removing 62% of the feed weight.

Jan 1, 1990

By Kerry J. Stanaway, Thomas E. Garnar

Titanium was discovered in 1791 and, four years later, was named after the Titans of Greek mythology. Titanium metal was first made in 1910, but was not used commercially until the 1950s when it was nick-named The Wonder Metal of the Age. The first titanium dioxide (TiO2) white pigments were produced commercially in 1915; more than 90% of the titanium minerals produced in the world today are used in the manufacture of white pigments. The remaining 10% are used to manufacture titanium metal and other uses such as welding rod fluxes. Titanium mineral mining began in the United States between 1880 and 1900 in Chester County, Pennyslvania. Rutile from a deposit near Roseland, VA, was mined in 1901. The use for the rutile was limited to production of a few titanium chemicals and for coloring ceramics. Larger scale mining for ilmenite, rutile, and zircon began in Florida to provide chemical materials for use in World War I in 1918. This mining ended in 1928. Large scale mining of titanium minerals in Australia began when Benick, Anderson, and Porter (later called Tamco) started mining the beach sands at Yamba in New South Wales in 1935. Ilmenite production from beach sands in the State of Kerala in southwestern India also began in the 1930s. The 1940s saw many changes in titanium mineral mining. Extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec. The Pigments Department of E.I. Du Pont de Nemours & Co. lost their high grade Indian ilmenite supply after World War II began, and they were forced to use lower grade ilmenite from National Lead&apos;s (now NL Industries) Sanford Lake Deposit, near Tahawus, NY, in the Adirondack Mountains. At the end of the war, Du Pont undertook an intense search for a domestic ilmenite source. With the cooperation of the US Bureau of Mines, Du Pont geologists found a very large deposit east of Starke, FL, in 1946. In 1948 Du Pont entered into a contract with Humphreys Gold Corp., who operated a heavy minerals mine near Jacksonville, FL, to construct a plant and operate it for a period of ten years. The plant started up in 1949 and operated under Humphreys&apos; management until the contract expired in 1958. Du Pont has operated the plant since that time. In 1956, a second plant was designed and built by Du Pont a few kilometers northeast of the town of Lawtey. The 1960s saw titanium mineral production expand in the southeastern US with Humphreys&apos; contract mining Du Pont&apos;s ore body at Folkston, GA. In the early 1970s. American Cyanamid and Union Camp Paper Co. formed a joint venture company, Titanium Enterprises (TE), to mine and separate titanium minerals from Union Camp&apos;s ore deposit southwest of Green Cove Springs, FL. In 1975 the TE plant was shutdown and later sold to Associated Minerals (USA), Inc. (AMC), a subsidiary of Renison Goldfields Consolidated Ltd., an Australian company. It now operates under the name RGC (USA). Mineral production grew in the 1970s with the development of extensive heavy mineral deposits at Eneabba in Western Australia and Richards Bay in the Republic of South Africa. The 1980s saw the construction of a very large ilmenite mine and synthetic rutile processing plant in the state of Orissa southwest of Calcutta, India. At the same time, concern for titanium mineral shortages expected by the end of this century, gave rise to a flurry of exploration activity during the mid 1980s. As a result, large deposits were found in Virginia and North Carolina. New deposits were also discovered in Australia. Fig. 1 shows the distribution of world titanium deposits and mines. The world TiO, production capacities are given in Table 1.

Jan 1, 1994

By A. McCombs

Previous models describing the aggregation of polymer-coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called "active" sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1988

By Roberto Zaragoza

Historically, the control of flotation operations has been viewed by many as an art. Only recently has process measurement and control come to be viewed not as an ?art? but as a very complex and productive science. In recent years, process control applications to flotation plants have been established and already some gains have been reported for several industrial operations using individual stabilizing control loops including level, pulp flow, pulp density, reagent addition rate and pH (Paakinen, 1979; Hales, 1985). The use of process control computers combined with on-line x-ray florescence (XRF) in industrial flotation circuits has made the application of more sophisticated control techniques feasible in the mineral recovery process. In spite of the availability of reliable instrumentation in modern flotation plants, satisfactory control strategies are difficult to develop and implement. Extremely important factors such as changes in ore type, liberation characteristics, flotability, degree of oxidation on particle surfaces, and specific gravity constitute unmeasured disturbances to the process. Most current control systems cannot adapt specifically to such disturbances.

Jan 1, 1987

By K. K. Cheng, Z. M. Chen, A. L. Mular

INTRODUCTION Since the nineteen fifties, process engineers have been seriously concerned with process models for various purposes (1,2,3). Models serve as subroutines to mathematical flowsheets which simulate circuits of interest. Simulators can serve to increase process know- ledge, assess circuit performance, investigate flowsheet modifications, evaluate new flowsheets, perform off-line optimization, and compare alternative control strategies. This chapter describes a methodology to develop a simulator of a bulk Cu-Mo circuit comprised of roughers, scavengers and 3 stages of cleaning. The simulator was employed to evaluate the influence of water addition at circuit points and to estimate the optimal number of cells for each stage in the circuit. DESCRIPTION OF CIRCUIT Figure 1 is a flowsheet of the Brenda Mines Ltd. (located near Peachland, B. C.) bulk Cu-Mo flotation circuit as simulated prior to an expansion/renovation which involved the installation of large, new flotation cells. Referring to the flowsheet, feed to rougher cells includes fresh feed, scavenger concentrate and 1st cleaner tailing. Rougher con, 1st cleaner (sect ion 2) con and 2nd cleaner tailing are fed to 1st cleaners (section 1). 1st cleaner (section 1) concentrate and 3rd cleaner tailing serve as 2nd cleaner feed, while 2nd cleaner concentrate is fed to the 3rd cleaners which produce a final bulk concentrate. Table 1 lists cell types and specifications important to the circuit. DEVELOPMENT OF MODELS To develop flotation cell models a systematic procedure was employed (4). This involves the selection of responses and factors, proposing models to be fitted, the acquisition of raw data, the statistical adjustment of raw data, fitting models to adjusted data and testing the adequacy of fitted functions. Responses and Factors Responses of interest included recoveries, concentrate grades and concentrate solids/water flow rates for each stage. Factors that influence these responses, such as reagent addition rates, air flow rates to cells, solids and water flow rates to stages and feed grades were not manipulated during the sampling period. Thus, the investigation was limited,

Jan 1, 1986

By Charles H. Wells

This paper describes a commercial installation of a sophisticated instrumentation and control system designed to maximize the performance of heavy medium cyclones. Samples of plant feed and its products were collected and analyzed for ash content so that measures of efficiency could be determined for plant operation under (1) manual control and (2) automatic (computer) control. The heavy medium cyclone control strategy and its digital computer implementation are discussed in detail. The sample results are analyzed and the economic benefits of automatic control are discussed. Results from the initial data sets quantify the economic benefits of automatic closed-loop control; viz, increased recovery and reduced clean coal variability have been clearly demonstrated.

Jan 1, 1981

By G. Van Weert

Refractory ores and concentrates containing silver tend to form Ag-jarosite during autoclave oxidation. Silver extraction from the oxidation products is therefore low, unless a hot lime treatment step to decompose Ag-jarosite precedes cyanidation. Since silver iodide is very stable but soluble in cyanide solutions, the formation and decomposition of Ag-jarosite in the presence of iodine species was studied. Results indicate that Ag-jarosite formation could be prevented in favour of H3O-jarosite and AgI while oxidizing Ag2S under industrial autoclaving conditions, when the total iodine species to Ag mole ratio exceeded 5. Lower ratios gave proportionally more Ag-jarosite and less AgI. Under these conditions existing Ag-jarosite was also found to decompose in H30-jarosite and AgI.

Jan 1, 1993

By James S. Browning

This article describes research conducted by the University of Alabama&apos;s Mineral Resources Institute on removing sulfur from coal using a combination of gravity concentration and flotation methods. The research used the gravity and centrifugal force capabilities of Humphrey&apos;s spiral to remove part of the pyritic sulfur and ash. Flotation of the Humphrey&apos;s spiral coal concentrate removed additional sulfur and ash. In addition to obtaining good recoveries of high quality coal, the tests demonstrated that pyrite in the wastes could be isolated as enriched flotation products by the combined gravity-flotation approach. Domestic coal production in 1980 reached a record 757 Mt (835 million st). Forecasts are that coal production and use will approach 907 Mt (1 billion st) by 1985, with much of the increased production being used for electrical generation. Of current production, it is estimated that about 454 Mt (500 million st) of coal nationwide are subjected to some degree of cleaning, ranging from crushing and screening to gravity concentration and flotation. With expanded coal production and more rigid controls placed on coal combustion, it is reasonable to assume that the tonnage subjected to some form of preparation will increase, with time, thereby adding to the burden of coal rejects being generated. A major problem associated with increased coal use for electricity generation is the need for utilities to conform to emerging federal air quality standards for sulfur oxide emissions from power plants. To a lesser extent, other industrial operations burning coal face a similar situation. Controlling sulfur oxide emissions by using low-sulfur coal or resorting to stack gas desulfurization are two recognized approaches, but removing sulfur from the coal, if possible, by physical beneficiation before combustion is preferred because of its simplicity and lower cost. Reducing the inorganic sulfur in coal to tolerable limits by physical beneficiation, including flotation, as now practiced, is still relatively inefficient and has not kept pace with the more sophisticated physical beneficiation approaches generally employed by the nonfuel minerals industry. As one phase of a broad program conducted by the Mineral Resources Institute at the University of Alabama on sampling and evaluating impounded fine size waste coal, tests were made using samples from two impoundments to determine the quality of coal recoverable by a combination of Humphrey&apos;s spiral concentration and flotation. Particular attention was given to organic and inorganic sulfur deportment and distribution in the various products. Another objective was to determine if pyrite in the waste could be recovered for possible marketing. The use of Humphrey&apos;s spirals to concentrate fine coal was practiced as early as 1947. At that time, the Hudson Coal Co. used spirals to concentrate anthracite fines. In 1950, spirals were used to treat fine-size bituminous coal and later, in 1976, spirals were reportedly used for removing pyrite from fine-size coal. More recent investigations have discussed the use of Humphrey&apos;s spirals for treating fine-size waste coal in Alabama. Samples Description Washer waste samples were obtained from two impoundments. One sample was representative of waste generated during washing steam coal from the American, Pratt, and Nickel plate seams in Alabama. The other sample represented metallurgical coal washer waste from processing coal from the Carter, Johnson, and Milldale seams. Partial samples analyses are shown in Table 1, and screen analyses of the samples are given in Tables 2 and 3. Screen ana¬lyses showed that one sample contained about 4% of material coarser than 2 mm (10 mesh) and the other contained about 13% of plus 2 mm (10 mesh) material. Also, the analyses indicated that ash and sulfur increased as the material&apos;s particle size decreased. Experimental Laboratory Tests Sink and float tests using a heavy liquid (1.4 specific gravity) were made on the different screen sizes shown in Tables 2 and 3 to determine the effectiveness of gravity concentration for separating coal from pyrite and other gangue constituents. Tests indicated that gravity separation, under optimum conditions, could be expected to yield coal products containing 10-12% ash, and 0.2-0.3% pyritic sulfur. Good coal recoveries could also be expected. Using sink-float tests as a guide, tests were made in a Humphrey&apos;s spiral by a procedure in which a 90-135 kg (200-300 lb) portion of the

Jan 8, 1982