Search Documents

By S. P. Singh

In order to simulate the operation of coal extraction machines, a portable workability instrument has been designed. Initially, the tests were performed with the instrument on modeling material, which were followed by in situ tests on coal in underground mines. The peak and mean cutting resistance and work done to cut a unit length of coal were determined for coal as well as modeling material. In addition, rebound strength and dynamic penetration tests were also performed in situ. On the basis of the cutting characteristics of coal, a "Workability Index" has been developed and its role in the judicious selection of coal cutting machines has been discussed. With reference to prior works and the strength characteristics of coal, it was found that the coal plow may not be suitable for the seams under investigation and the shearer seems to be the only choice. It has been observed that peak cutting resistance and the "Workability Index" in the case of coal as well as modeling material depend upon compressive strength. The peak cutting resistance exhibited certain dependence upon the Schmidt rebound hardness and dynamic penetration strength of coal in situ.

Jan 1, 1984

By H. Staton, N. Michaelson

"INTRODUCTION Lundin Mining’s Eagle Operation, located in Marquette County, upper Michigan consists of a mine and concentrator that process a Ni-Cu-(PGE) ore. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 66 miles to the Humboldt mill where both nickel and copper concentrates are produced. Operations began in 2014 and continued with an average production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year for the first three years of operation. The Humboldt Mill, currently operated by Lundin Mining, processes the nickel/copper ore from Eagle Mine and performs the concentration through several stages of flotation. Originally built in 1954, the Humboldt Mill began operations as an Iron Ore processing facility, and was converted to a gold processing plant during the 1980s. Various groups owned the site after closure of the gold operation. Eagle purchased the Mill in 2008 and invested more than $280 million to clean up historic mine waste and refurbish the plant (see flowsheet in APPENDIX). This paper will overview the ramp-up of the operation, and discuss some specific areas that went well and some that could have gone better during the design phase. HIGH LEVEL DESIGN CRITERIA Coarse ore arrives from the mine and is stored in a building with a capacity of 10,000 tonnes. Ore is crushed in three stages to a final product size of 100% Passing 12mm. Crushed ore is conveyed to the mass flow fine ore bins, which have a live capacity of 3000 tonnes. Crushed ore is fed to two parallel 900 HP ball mills, charged with 3” high chrome grinding media, and ground, in closed circuit with hydrocyclones, to a p80 of 110 microns in the flotation feed. Soda ash is added to the mills based on process water hardness. Cyclone overflow passes to the bulk conditioner where Sodium Isopropyl Xanthate (SIPX) and Methyl Isobutyl Carbinol (MIBC) are added. The slurry is pumped to the rougher bank for bulk flotation. Rougher concentrate is fed to a 500HP vertically stirred regrind mill and is ground to a p80 of 50 microns, using 5/8” high chrome balls. Rougher tailings report to the tailings thickener. The regrind cyclone overflow is sent to the single stage cleaner bank followed by two scavenger banks. The cleaner concentrate is pumped to the copper-nickel separation circuit. Cleaner tailings report to the tailings thickener. In the copper-nickel separation circuit, the pH is raised to 11.5 and a copper concentrate is recovered from the bulk cleaner concentrate in two stages, namely the copper roughers and the copper cleaner columns. The concentrate from the copper flotation columns is the final copper concentrate. The tailings from the columns return to the head of the copper-nickel separation. The nickel concentrate is the copper rougher tailings stream."

Jan 1, 2018

By J. A. Cole

Santa Fe Pacific Gold's Lone Tree mine is located in Humboldt County, NV, 45 km (28 miles) east of Winnemucca. The mine currently operates a 1.74-Mt/a (1.92-million stpy) run-of-mine heap-leach operation and a 2.27-kt/d (2500 stpd) refractory gold¬ore-processing plant. Most of the mill-grade ore reserves are refractory, mainly due to pyrite and arsenopyrite encapsulation of the gold. The autoclave pressure-oxidation circuit was commissioned in February 1994 to process the refractory ore. Mineralogy unique to the Lone Tree deposit allowed for the design of a partial-oxidation process. It takes advantage of the heterogeneous nature of the pyrite morphology. Partial oxidation has resulted in an autoclave plant that is able to achieve low operating-unit costs (Figs. 1 and 2).

Jan 1, 1995

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By W. A. Rickelton

Trialkylphosphine sulphides, in contrast to their well known oxide analogues (1,2,3,4), have received comparatively little attention as metal extractants and previous studies have been biased toward analytical rather than commercial solvent extraction applications (5,6,7). The sulphides are soft Lewis bases and only from complexes readily with the limited number of metals in the periodic table which can be classified as soft acids (8) e.g. Ag+, Hg2+ and Pd2+. Consequently, these compounds tend to be more selective than the broad-spectrum, hard-base, phosphine oxide extractants such-as TOPO (trioctylphosphine oxide). The purpose of this paper is to describe a potential application of one phosphine sulphide, CYANEX® 471X extractant, in the selective recovery of silver from base metal sulphate solutions. CYANEX 471X is triisobutylphosphine sulphide (TIBPS).

Jan 1, 1984

By W. I. Enderlin, P. O. Jackson, J. A. Glissmeyer, K. B. Olsen

A reliable estimate of radon emissions to the environment from underground uranium mines was obtained through measurements of radon in ventilation air at 24 mines and from estimates of radon release from other mine sources. The total production of U308 from the mines sampled represents about 63% of the total U.S. production from underground mines (1978 statistics). Wide variation in the radon emission rate per unit of production was found from mine to mine. Using the total radon emitted and U308 produced by all mines sampled, an average of 26.7 Ci of radon was emitted per ton of U309 produced. The investigation includes a brief study of the sources of variation of the emission rates. A statistically significant relationship was found between the measured radon release rate and the cumulative ore production at several mines.

Jan 1, 1981

By John Oskam

In 1873 Barton tines Corporation mining Garnets for Abrasives. From providing bulk Garnet Concentrate the technology has advanced to the sizing and classification of micron sized particles utilizing a Barton process. Processing of Garnet involves extensive quality control at all steps, first to insure product purity and secondly to insure the correct size range. Barton Mines produces about 30 different sizes of Garnet products to lead the world in the manufacture of technical abrasive Garnet. This paper will examine the present technology of Garnet Abrasive Manufacture and the specification to which the sizes are produced as well as some of the markets served.

Jan 1, 1980

By T. A. Jones

The Kelsey Centrifugal Jig is an enhanced gravity concentrator capable of separating fine minerals and/or minerals with relatively small differences in specific gravity. Since the first commercial installation at the Renison Bell tin mine in Australia, development and improvement in hardware has continued, including the introduction of the high-capacity J1800model Kelsey Jig. The Kelsey Centrifugal Jig is widely applicable to fine mineral recovery duties, with key application areas including mineral sands, tin, gold and nickel. Other areas of application include: iron ore, base metals, chromite, PGMs, soil remediation and scheelite. The latest developments on the Kelsey Jig are discussed together with a review of recent installations involving: • Fine gold / sulphide recovery from leach tailings • Magnesium mineral removal from nickel sulphide concentrates • High-grade zircon recovery from plant tailings

Jan 1, 2004

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024

By S. D. F. Rocha, A. L. A. SANTOS, E. M. A. BECHELENI, F. P. C. Silvas

Hydrometallurgical processes are needed to extract nickel (Ni) when it is disseminated in mineral matrix. High-pressure acid leaching (HPAL) and atmospheric acid leaching (AAL) are alternatives, and AAL has the advantage of requiring mild temperatures and pressure. Reducing-reagent tests improved the extraction of metals for the specific limiting portion of the ore. Low dosage of sodium thiosulfate presented better selectivity and safer operating conditions, allowing metal extractions of 50–62 percent at 95 °C. However, the low extraction rate obtained for Ni and the similar levels of impurities — magnesium (Mg), manganese (Mn), cobalt (Co) and iron (Fe) — extracted may represent economical and technological challenges in the downstream process.

By John Hanna

The Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of phosphate minerals from siliceous ores. The process takes advantage of preferential adsorption and high reactivity of fatty acid collectors towards apatite over silica surfaces under slightly acidic conditions of pH 5-6.5. The process was successful in upgrading various phosphate samples from Florida and North Carolina containing 7.7-15.3% P205 and 62.3- 77.2% Insol to concentrates assaying 28.1-33.1 % P205 and 4.1-9.9% Insol with high P2O5 recovery of 81.8-92.2%. Depending on the type of silica impurities present one or more cleaning steps, with or without sodium silicate, would be required to improve the grade of the rougher phosphate concentrate.

Jan 1, 1992

By J. A. Bartnik

Flocculation, the process of coagulation or coalescence of finely divided particles, is commonly used in separating fine solids from fluids. Forces disposing of the particles to flocculate include: ionic forces of attraction, secondary entropic forces, and magnetism. Magnetic flocculation is due to a physical magnetizing process which affects suspended ferromagnetic particles. Such particles, after exposure to magnetic fields strong enough to cause reorientation of the particles and alignment of the induced magnetic poles, tend strongly to retain this induced magnetism, as the magnetic retentivity of ferromagnetic particles is a linear function of its specific surface.1 Thus, because they become small magnets with high residual magnetism, the particles become and remain attracted to one another, forming large agglomerates. Fine magnetic particles close to domain size can exhibit energies of the magnetization of the order of 105 ergs/cm3,2 which is many times greater than the energy affected by chemical flocculents. Therefore magnetic flocculation can be used to agglomerate particles having surfaces ionized with like charges and only a minute quantity of ferromagnetic material will be necessary to develop sufficient force to overcome the repulsive ionic forces and hold together relatively large masses of fine solid agglomerates suspended in fluids. Since flocculation occurs after the fine suspension passes through a magnetic field generated by magnets surrounding a pipe section, the simplicity of the process and economic advantage makes magnetic flocculation very attractive.

Jan 1, 1971

By Bülent Erdem, Zekeriya Duran, Tuğba Doğan

The objective of this study was to evaluate the potential health risk associated with exposure of dozer operators to whole-body vibration. Measurements were made on 31 dozers used in different surface mines in Turkey. Predictions of adverse health effects of vibration were based on the standards BS 6841:1987, ISO 2631–1:1997, ISO 2631–5:2004, and the EU Vibration Directive:2002. Operators experienced high and comparable levels of vibration acceleration and dose during all dozer tasks: pushing the material (DOZE), moving forward (FORWARD), moving backward (REVERSE), and ripping (RIP). Specifically, DOZE, FORWARD, REVERSE, and RIP showed high potential of adverse health effects in terms of vibration dose according to the worst-case axis and vector sum criteria and a moderate adverse health effect for acceleration according to the worst-case axis criterion. Operators of large dozers were exposed to lower levels of vibration. However, no statistically significant relationship between vibration exposure levels and the propelling mechanism and the service time of dozers, operator experience, operator age, and ground type was found.

Jun 16, 2022

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By Y. B. He

The effect of the overflow to underflow (O/U) flowrate ratio of a dense medium cyclone on its performance is tested utilizing a 6" dense medium cyclone and density tracers. The results show that the O/U flowrate ratio is clearly correlated with the separation cut point D50, the separation efficiency Ep, the density differential 0, and short circuiting of the cyclone. Within certain limits, a higher O/U ratio results in a better separation efficiency, a higher D50 and an increased density differential. A lower O/U ratio, on the other hand, reduces the cut point shift and density differential. The phenomenon of short circuiting to the underflow, which is especially significant for fine particles, is directly connected with an excessively low O/U ratio.

Jan 1, 1992

By A. B. Cecala

The US Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the US coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1995

By C. J. Roos

Ground-engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these "consumable" items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corp. to predict the consumption of excavator teeth at a particular mine site. This paper presents the results of the Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2010

By James A. Holtkamp

Environmental regulation in Mexico has matured dramatically and effectively in the last decade. The gap between environmental regulation in the United States and Mexico is rapidly narrowing. From a regulatory perspective, it is no longer necessarily less burdensome to operate in Mexico. Principal laws and regulations Mexico has two principal environmental regulatory systems. The first consists of the laws and regulations governing domestic activities. The second consists of the treaties, agreements and understandings between the United States and Mexico dealing with transboundary pollution and maquiladoras (see Maquiladora Decree, next column). The following are the principal major laws and regulations governing environmental protection in Mexico: General Law: The General Law on Ecological Balance and Protection of the Environment, effective March 1, 1988. Water Regulations: Regulations for the Prevention and Control of Water Pollution, effective May 29, 1973. Environmental Impact Regulations: Regulations of the General Law on Ecological Balance and Protection of the Environment, regarding Environmental Impact, effective June 8, 1988.

Jan 1, 1994

By J. P. Gliddon, G. C. Wade, J. W. Lill

Since 1980 a number of significant changes have been introduced at Palabora in an effort to offset the effects of reduced product price and increased unit costs of production. These changes and improvements include major equipment rationalization programs, the introduction of trolley-assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives, and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation, and their contribution to cost reduction and improved productivity at Paihbora are considered.

Jan 1, 1987

By A. W. Khair

This paper deals with the evaluation of the interaction between rock and the cutting tool, and with methods for determination of workability, and abrasivity of rock. A description of instrumentation is included along with research on the wearing process of bit tips and pick consumption. Analyses of bit rotation, evaluation of cutting, normal forces and energy consumption is presented. Finally influence of the basic water jet parameters and water jet assistance on the cutting process of hard and abrasive sandstone is discussed.

Jan 1, 1995