Search Documents

By W. A. McKinney

The U.S. Bureau of Mines, Kennecott Copper Corp., and New Mexico Institute of Mining and Technology are cooperating on a research project to improve extraction of copper from previously leached waste dumps that are in part compacted and impervious to leach solutions. The field work is being done at the "J" leach dump, Chino Mines Division, Kennecott Copper Corp., Santa Rita, N. Mex. The laboratory percolation leaching tests were made at the U.S. Bureau of Mines Salt Lake City Metallurgy Research Center on drill core samples from the "J" dump to determine how much copper might be leached if permeability could be restored by explosive heaving or other means. The core samples from nine drill holes on "J" dump contained from 0.06 to 0.14 percent copper. Copper extractions ranging from 15 to 3 percent were obtained in 75 days by percolation leaching of minus-1-inch material with dilute sulfuric acid. The tests results indicate that about 2'7 percent of the copper remaining in the "J" dump could be extracted under ideal leaching conditions.

Jan 1, 1970

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By F. D. Huntley

Raw materials used by the Flat Glass Industry are known in the Industrial Minerals geology sector as Specialty Products. These pro- ducts must meet specification limits usually not the same for all glass manufacturers. Evolving new glass compositions will require mineral concentrates of consistent purity being produced within economic limits that will assure market viability of the resulting glass product. The amount of success the Flat Glass Industry will achieve by developing and maintaining domestic production centers will be determined by many economic factors which affect the costs of doing business. Technological developments by mineral processors must continue in order to achieve more efficient production of high quality glassmaking raw materials.

Jan 1, 1986

By A. Ferreira Morgado

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999

By A. C. Beaulieu

CITY OF EDMONTON Rate of Growth The City of Edmonton has been classed by some economists as being the most progressive City in Canada since the early 50's. The high rise buildings that are changing Edmonton's skyline, the rapidly expanding sewer and water network, and the proposed rapid transit system all indicate the requirements of an ever expanding City. Edmonton, the core of Canada's Energy Empire is the country's seventh largest metropolitan area. Bisected by the 22 mile long park of its magnificent river valley, it sits in the midst of the 50,000 sq miles of riches that have created it. Underneath the City, however, extending down for thousands of feet and encircling it for a radius of scores of miles, lies a fabulous store of petroleum wealth. By the early 1940's, based upon the needs of the farming areas, accompanied by some small exploitation of coal and timber, Edmonton grew to 100,000 people. Then in a short space of 20 years Edmonton shot up to be a city of 450,000. Figure 1 (Slide No. 1) indicates the population growth in the City of Edmonton and the Census Metropolitan Area from 1906 to 1971.

Jan 1, 1997

By J. A. Reizes, C. A. J. Fletcher, T. Jancar

Spirals play an important role in fine coal and mineral processing. To date, almost all spiral designs have been empirically based. Although many operational units have evolved utilising this approach, it does not necessarily lead to optimal spiral designs. This paper presents the preliminary results of a collaborative computational and experimental research program to understand the detailed separation process which will ultimately lead to a parametric assessment of alternative spiral designs through computational simulation. Unlike the empirical approach, a computational simulation is only subject to the fundamental physics of the fluid flow. No prior knowledge of the generic spiral flow is necessary. The computer code implements a robust finite volume technique to predict the three dimensional fluid motion. A height function method is used to model free surfaces and the code is capable of handling arbitrary spiral geometries. Preliminary validation of the computational simulation is carried out through analysis of an existing spiral design -the Mineral Technologies LD9 unit. Computational flow predictions are compared with experimental measurements obtained using a number of techniques, including sampling and flow visualisation, for flow test cases where no solid particulate is present.

Jan 1, 1995

By Anthony J. Stewart, Jim W. Rosteck

This paper will discuss some of the equipment used to construct the middle segment of the MetroWest Water Supply Tunnel. The $252 million, seven-year project located in Framingham, Massachusetts consisted of two hard rock TBM drives worked from a single shaft. The 24,407-foot long west heading was constructed at the same time as the 35,006-foot long east heading. Also included was raise bore construction of four, 30-inch diameter steel lined riser shafts, one 12-foot finish and one 10-footfinish shaft as well as two major valve chambers. The main shaft was 400-feet deep and 32-foot diameter.

Jan 1, 2001

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on overall grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: •Different lining profiles in rubber and steel. •Orebed magnetic lining. •Steel-cap rubber lining. Introduction Grinding mill liner life has been a subject of extensive studies. Performance of mill liners in terms of wear life and how it relates to lining material and profile is abundant in the literature. The most economical liner material and design has been selected based on "cents per ton milled". The evaluation of the effect of liner design on power and grinding media consumption which is a far more significant part of grinding costs, has been less comprehensive (Fig. 1). Lining materials Steel. The most commonly used lining material is steel, calculated on a volume basis. Steel linings have a long tradition and a number of alloys is being developed. The main families are: •High chromium white iron. •Cr and Ni white iron (NiHard). •High chromium martensitic steel. •High carbon Cr-Mo perlitic steel. •High carbon Cr-Mor martensitic steel. •Manganese austenitic steel. Steel linings can be successfully used in most applications. Rubber. Rubber linings were introduced 25-30 years ago and are today commonly accepted to be the most economical linings for secondary and regrind applications. Rubber linings offer long service life in these applications and generally [ ] outlast steel in wet applications, where corrosion is a factor on the steel. The cost relation between rubber and steel has changed dramatically over the years. In the past rubber was more expensive than steel, but today, the cost of rubber is close to half the cost of steel, calculated on a volume basis (Fig. 2). The present cost situation has made rubber linings an economical alternative in several primary grinding applications as well. The wear rate of rubber in primary applications is higher than the wear rate of steel, thus giving a shorter wear life. This can be compensated for by making the rubber lining thicker. The cost advantage of the rubber allows for this, but care must be taken not to jeopardize the grinding performance. Rubber, as a lining material, offers some distinct advantages over steel lining, such as: •Ease of installation and removal. •Safer to handle, less risk of injuries. •Faster replacement. •Reduces noise.

Jan 1, 1996

By Albert E. Ketler

The techniques for fire monitoring of conveyor belts in underground coal mines have been revolutionized by the advent of sensitive carbon monoxide sensors and computer monitoring systems. These new systems are rapidly replacing the previous thermal (fixed-point temperature) sensors that have been shown to be considerably less sensitive for early fire warning. CO is generally an excellent indicator of spontaneous combustion. However, the most recent non-flammable conveyor belt materials have been shown to "burn" with dense smoke, but without sufficiently high temperatures to produce much carbon monoxide. To cover this fire detection void, a smoke detector was developed to augment CO sensing for these new conveyor materials. However, computer monitoring provides the flexibility for handling this and other additional instrumentation as fire monitoring techniques evolve. CO, smoke and temperature sensing may eventually be advocated for complete fire monitoring.

Jan 1, 1987

By W. Collingwood, K. V. Raj, S. Bandopadhyay

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in openpit mines is relatively new. Modeling the actual pit geometry of an openpit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an openpit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in openpit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions and turbulence modeling parameterization. An appropriate mesh selection is critical. A detailed discussion of the meshing of the domain of an openpit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (κ-ε), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an openpit and some of the approaches adopted to address these challenges.

Jan 1, 2013

By F. C. Turin, T. L. Friend, A. G. Mayton, J. S. Jaspal, W. J. Wiehagen

This paper describes the serious injuries that have occurred to bulldozer operators working at domestic coal, metal and nonmetal mines in the United States. A serious injury is defined as one that results in either a fatality or in lost work time. Examined were 873 injury records compiled by the Mine Safety and Health Administration (MSHA). The time period covered was 1988 through 1997. These injuries resulted in 18 fatalities and 31,866 lost work days. All of these injuries occurred to dozer operators while they were performing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Jolts and jars accounted, for 604 or 70% of the serious injuries to bulldozer operators, and jolts and jars accounted for 75% of the workdays lost. Vertical jars comprised the largest set (354 incidents) of jolting and jarring injuries. In more than half of these incidents, the operator was backing up the dozer. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fallover or rollover, seven out of 17 of the operators were killed. This study finds that further reductions in injury risk would require more widespread use of seat belts; consideration (and maintenance) of the seat and seat suspension systems that might reduce injury risk from jolts and jars; research interventions to assess the effect of alternative engineering designs to dampen or isolate the effects of shock and vibration; and continued attention to skilled performance, i.e., the integration of hazard awareness, recognition and response with dozer operational skills.

Jan 1, 2003

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By J. A. Herbst

A state of the art computer simulation package, named UTAH-MODSIM is being developed. This package can run on a mainframe (eg. UNIVAC) as well as on a microcomputer (eg. IBM/PC with at least 512 kBytes of core memory). Friendliness was the major concern in developing this software. The user simply generates a complete flowsheet by presenting the flowsheet on a graphics terminal. This flowsheet defines the circuit to be simulated. With the minimum required data, the user can obtain a complete mass and water balances within a few minutes. Moreover, this package will provide scale-up and capital cost information of specified equipment relevant to design. In order to illustrate the utility of this software, three design examples are given. They are: a) A typical multistage crushing plant. b) A reverse closed grinding circuit comparing one stage with two stage classification. c) A standard closed grinding circuit suitable to liberate a specified fraction of chalcopyrite from a copper ore.

Jan 1, 1986

By J. Scheepers, P. Smith, G. (Yunfei) Qiao

High pressure acid leach (HPAL) and pressure oxidation (POx) or pressure leaching extraction processes occur in autoclave vessels operating at elevated temperature and pressure, acidic conditions with abrasive mineral slurries. The harsh process conditions require specialized severe service metal seated ball valves to support operation of the vessels. Over several decades thermally sprayed titanium dioxide (TiO2) and chrome oxide (Cr2O3) coatings have been applied to extend the service life of the ball valves and other high wear critical components. Variability in the coating application quality control and severe process conditions can result in spalling, coating failure and premature failure of the component resulting is decreased autoclave circuit availability. In 2012 MOGAS, together with BRENCO, initiated research and development for ML-381, metallurgically bonded coating. This paper includes the historical development of severe service ball valve coatings, success of the trials and increasing industry adoption of the ML-381 coating for ball valves and other critical autoclave circuit components.

Mar 2, 2022

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By A. L. Wilder

Coeur d'Alene Mines Corporation's newest precious metals property is located in the old Rochester Mining District approximately twenty-five miles northeast of Lovelock, Nevada. Built at an elevation in excess of 6 000 feet, the Coeur-Rochester gold silver heap leach property encountered cold weather operational problems typical of most northern Nevada heap leach properties, soon after the start-up of operations last fall. Due to the size of the heap area under leach at Rochester, it was decided that 1 the usual practice of spraying to an "ice field" and waiting for the spring thaw was impractical. Further, the delivery schedule for a solution heating system of the size required was unacceptable. Accordingly, Rochester personnel embarked on a program to seek out a leach solution distribution system that would enable an operation through the winter and yet be cost effective. The findings of this program were rather dramatic and, as a result, the whole perception of heap leach solution application at Rochester has changed forever.

Jan 1, 1988

By Y. Wang, G. Xu, N. A. Amoah, A. Kumar

Mining-induced coal dust causes various respiratory diseases to mine workers, such as coal workers’ pneumoconiosis (CWP). Current available underground monitors are expensive, heavy and only measure mass concentration. These disadvantages limit them for regulatory sample monitoring purposes only while personal exposure levels for most miners remain unknown, risking miners to potential overexposures. Low-cost light scattering PM sensors offer a potential solution to this problem with capability of high spatio-temporal resolution PM characterization. However, these sensors require careful calibration before they can be applied in mining environments. There is basically no comprehensive study in the literature using a standard protocol assessing these sensors for coal dust monitoring. With the aim of calibrating the PMS5003 sensors for coal dust monitoring, we design the calibration method and system to calibrate these low-cost PM sensors coal dust monitoring. Working principles of present coal dust monitor and low-cost sensors are presented in detail. The linear regression calibration model which is used for the sensor calibration is further described. Sensor calibration and evaluation protocols are comprehensively compared and discussed. This investigation reveals the feasibility of low-cost sensors for real-time personal coal dust monitoring in underground coal mines.

Mar 2, 2022

By A. S. Ibrado

The adsorption of silver on activated carbon from cyanide solutions was studied as a function of concentration, ionic strength and pH. In cyanide solutions, silver exists mainly as the linear Ag(CN)2 complex and adsorbs on activated carbon following the Freundlich isotherm. The uptake and rate of adsorption increase with the addition of KC1 and KNO3 but changes only slightly with pH. In contrast, the adsorption of Cu(I), Zn(II), Cd(II), and Hg(II) shows marked changes with pH, closely following the predominance profiles of their neutral and singly-charged cyano complexes. Clearly, multicharged negative complexes are repelled by the negatively-charged carbon surface. This sensitivity of activated carbon to the charge of the adsorbing species indicates that silver adsorbs as an anion, not chemically bound to the co-adsorbing counterions. For the same reason, activated carbon is selective to metals that form neutral and Singly-charged cyano complexes, namely gold and silver.

Jan 1, 1988

By R. A. Kirkland

The oxygen consumption method utilises an oxygen sensor to monitor the gas-phase oxygen concentrations in sealed chambers filled with reactive waste rock with subsequent confirmation of the oxygen content by gas chromatography. Results of experiments utilising low sulphide (<0.5w1%) waste rock yielded reproducible oxygen consumption rates on the order of 10-10 mol O2.kg-1. s-1. Petrographic analysis of the waste rock material indicated that the dominant sulphide mineral is pyrite (FeS2). Assuming a stoichiometry of 1.75 moles of O2 per mole of SO4 sulphate release rates were inferred to be between 6 and 18 mg SO4 kg-1 wk-1 Typically these results are 2 to 3 times greater than measured sulphate release rates from humidity cells. Our findings suggest that this techniques offers a rapid. cost efficient method for determining sulphate release rates in waste rock piles, even at low sulphide concentrations.

Jan 1, 2000

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) am-mines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Jan 1, 2011