Search Documents

By Tor L. Brekke, Alberto Marulanda P.

The paper describes hazardous water inflows during construction that have taken place over the last three years in tunnels in Colombia. The projects involved are the Chivor II Hydroelectric Power Project (penstock tunnel), and the Chingaza Water Project (two tunnels). In all cases, loss of face control led to significant loss of ground; in one case some 70,000 m3 of slide material was involved, much of which came out through the portal situated 1.6 km from the face. Emphasis is given to: (a) the geologic setting, (b) the remedial measures taken, and (c) the main efforts that can be made to prevent hazardous conditions from developing.

Jan 1, 1981

By Unto Paakkinen

The testing of different kinds of process flow configurations and cell volumes in industrial scale flotation processes is in general difficult to accomplish and even expensive to perform.1 Also the lack of suitable measuring and analyzing devices often prevents effective comparison of results. Nowadays, the existing flotation processes contain, almost with exception, several return loads which result in difficult control of the process. There exist two good reasons for testing different kinds of flotation circuits at the Outokumpu Oy Kotalahti mine. Firstly it is easy to change the process flow configuration without any additional installation work and secondly, the concentrator is highly automated with magnetic flow meters, on-line analyzer and process computers. In this presentation, open circuit flotation is compared with the classical closed circuit flotation which contains return loads. In additional, the effectiveness of computer control in both cases is estimated and also the effect of cell volume on flotation results is examined.

Jan 1, 1977

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

The efficient and effective utilization of hydraulic excavators relies on, among other factors, a better understanding of the formation resistance during the excavation process. Studies on hydraulic shovel excavators have focused on optimizing the digging process by considering the reaction of the boom, stick and bucket, and analyzing the resulting moments at the shovel’s front-end joints. These studies failed to understand resistive forces from a statistical viewpoint. The purpose of this paper is to develop machine-learning models capable of predicting the formation of resistive forces during shovel excavation. The shovel’s excavation was simulated in the PFC 5.0 environment using a typical field-size hydraulic shovel bucket to generate the shovel contact forces required to overcome formation resistance

By P. Mousset-Jones, F. Calizaya

Ultrasonic anemometry is a relatively new method of measuring the air velocity in underground excavations and is not widely used. The method has been mainly used for surface applications, such as meteorology and fluid flow measurement. Several instruments were looked at to determine their applicability for continuous underground monitoring systems. The units fall into two main categories: variable distance units and fined distance units. The method relies on the acceleration and deceleration of ultrasonic pulses transmitted through a moving airstream. This study presents some of the results of the testing of variable and fixed distance ultrasonic anemometers in a wind tunnel and a mine drift.

Jan 1, 1995

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By S. A. G. Poppen

The lining of a mine shaft is one of the most important considerations in the planning and operation of an underground mine. Generally, the function of a shaft lining is to preserve the shaft opening in a manner compatible with the expected mine life and -the other shaft operations. Where shafts are the only means of surface access in a mine, they also serve a critical function for the safety of the entire underground operation. Routine repairs and maintenance work on the shaft linings are only possible in stable strata with only minor interruptions to the shaft operations.

Jan 1, 1988

By A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation, both at the surface and subsurface of three longwall mines in northern West Virginia have been made. Ground movements were monitored during" a three year-period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including, graphical {NCB}, profile function, influence functions (USBM, BAL'S, KNOTHE'S, and zone area) will be presented. A brief geologic and topographic description of each site along with the instrumentation and monitoring program will also be presented.

Jan 1, 1989

By Parris A. Lyew-Ayee

This paper is the first preliminary report on the bauxites and terra rossas of the Caribbean. It concentrates on the islands of the Greater Antilles, and for reference purposes the Yucatan Penin- sula is included. At this point, observations made in Jamaica, Haiti, and the Dominican Republic are compared with reported information on Puerto Rico, the Bahamas, Cuba, the Cayman Islands, and the Yucatan Peninsula with regard to occurrence, as well as physical, chemical, and mineralogical composition. From this, an attempt is made at classifying the types of bauxites in the Caribbean, indicating the best reserves estimates, and the process ability of these bauxites. Some suggestions are also provided to fuel the controversy over the likely source material(s) or origin of the Caribbean bauxites.

Jan 1, 1984

By A. L. Frank, Benton

INTRODUCTION The selective sensitivity of plastic nuclear track detectors (PNTD's) to low energy 4He particles in an environment which also contains gamma and beta radiations has made these detectors prime candidates for the dosimetric measurement of the concentrations of radon and its daughter products in mine air. Their passive, integrating mode of measurement, small size, low weight and inexpensiveness are attractive characteristics for large scale personnel dosimetry. The detectors can be used in either active or passive dosimeters. In active devices, the PNTD is placed in close proximity to a sampling filter. The filter collects, from a calibrated air flow, all the daughter nuclei which are in suspension. As the daughter nuclei pass through the decay chain, through 214Po, a fraction of the 4He particles emitted are registered as latent tracks in the plastic. In passive devices, the PNTD is placed in direct contact with the ambient air containing the radio-nuclei concentrations to be determined. The active dosimeters have the advantage of excellent sensitivity, and the measured track densities yield very close approximations to accumulated Working Level (WL)** exposures. They have the disadvantage that the simplicity of the passive PNTD is lost, since a battery-driven constant flow-rate air pump is a necessity. The passive dosimeters are simple in construction and use, but they have the disadvantage that WL exposures are not directly measured and certain assumptions concerning radon and daughter equilibrium conditions must be made in determining WL exposures from the measured track densities. Also the sensitivities, in track densities per Working Level Hour (WLH) exposure, are much less than for active dosimeters. Dosimeters of both types have been investigated. Passive devices have been tested extensively both in the laboratory and in mines. Active devices have been laboratory tested. In our earlier measurements, cellulose nitrate plastic detectors were used exclusively, since this material had the highest sensitivity of the PNTD's then in use. When the properties of CR-39 plastic were discovered (Cartwright, 1978; Cassou and Benton, 1978), this material was used, where possible, to take advantage of its superior sensitivity. The results of our earlier work have previously been published (Frank and Benton, 1977). * Research sponsored by the Bureau of Mines, U.S. Department of Interior, under Contract No. JO-188003. ** A Working Level is defined as any combination of the short-lived radon daughters containing 1.3 x 105 MeV of potential 4He-particle energy per liter of ambient air. PASSIVE DOSIMETRY In the earliest testing of PNTD's for passive WL dosimetry, a single strip of cellulose nitrate plastic was used to determine the total cumulative 4He-particle activity in the air of simulated uranium mine and uranium mine environments (Rock, 1968; Rock [et al], 1969; White, 1969). The measurements yielded a close relationship between track densities and WL exposures in a controlled, static environment, but poor accuracy in the active mine tests. It was assumed that equilibrium differences contributed largely to the variations found. The response of PNTD's to airborne 4He-particle emitters, derived by Lovett (1969), demonstrated that detectors such as cellulose nitrate, which has a sensitivity cutoff at 4He-particle energies below the emission energies of radon and its daughters, are equally sensitive to the activity concentrations of radon, 218po(RaA) and 214Po(RaC'). Since radon does not contribute to WL as it is defined, and since, under normal ventilated uranium mine conditions, the radon activity constitutes about 40% to 70% of the total 4He-particle activity, the WL exposures calculated from measured track densities are very sensitive to the particular radon daughter equilibrium conditions. Also, the detector does not weight the individual daughter activities in proportion to their importance to WL. The equation for WL is WL = 0.00103C2 + 0.00507C3 + 0.00373C4 (1) where C2, C3 and C4 are the activity concentrations of RaA, RaB and RaC-C', respectively, in pCi/[L]. The detector leaves C3 unmeasured and weights C2 and C4, equally. [This problem has been approached by Domanski et al (1975, 1979), for some non-uranium mines, by measuring equilibrium conditions throughout the mines to determine a mean value for A, the inverse of the Working Level Ratio (WLR = 100 WL where C1 is the activity of radon-222 in pCi/[L].) The distribution of values allowed Domanski to determine probable errors in calculating WL exposures from track densities. However, measurements of equilibrium conditions in U.S. uranium mines (Breslin et al, 1969; Holub and Droullard, 1978) indicate that this method would not be accurate enough for uranium miner personal dosimetry.] A two-element dosimeter was designed at our laboratory to compensate for equilibrium variations. The first element is a radon detector; the second is a detector for the total 4He-particle activity in the ambient air, just as in the single element dosimeters cited above. The addition of the radon detector allows the equilibrium conditions for the individual nuclei to be determined, given certain assumptions concerning the interrelationships between the nuclei concentrations in mine air. The two detectors and the problems involved in calculating WL exposures from their measurements are discussed below.

Jan 1, 1981

By D. M. Bodily, V. J. Hucka

INTRODUCTION Interest in the recovery of methane from coalbeds has increased rapidly over recent years, because of its potential as an energy resource and to alleviate pollution and safety problems. The resource base of coalbed methane in the United States has been estimated at 11.2 Gm3, roughly equivalent to 20 years consumption (Mroz et al., 1983; Kuuskraa and Brandenburg, 1989). Methane contributes to the adverse environmental impacts of global warming, tropospheric ozone formation (smog), and potentially stratospheric ozone destruction. Association of methane with coal has always presented a safety problem in mines due to the potential for explosions. The rate of release of methane depends on the amount adsorbed by the coal, the adsorption isotherm for the coal, and the size of the coal particles. Mining operations can affect the particle size distribution and the production of fines and therefore the rate of release. The time the mined coal remains in the mine may also be important in determining total emissions. The methane content of some Utah coals was determined in this study. The methane content of the coals is compared with the chemical and physical properties of the coals and the properties of the seam and neighboring strata. Correlations are developed to better understand the formation and retention of methane by these coal seams. METHANE FORMATION IN COALBEDS Three mechanisms for methane formation may be considered: (1) nonbiogenic formation, (2) formation by anaerobic bacteria during plant material deposition and the early stages of diagenesis, and (3) formation from pyrolysis of coal material during coal maturation. Nonbiogenic formation by thermal processes involving carbon- and hydrogen-containing compounds has been proposed as a mechanism for methane formation in the earth. It is not likely to be of importance where other fossil fuel materials are present. Coal would not survive the temperatures required and hence the methane would need to migrate and be trapped by the coal seam. This mechanism is unlikely for coalbed methane. Formation of methane by anaerobic bacteria undoubtedly occurs during coalification, but the methane may not be trapped until the pore system of the coal is developed, and would likely be displaced by methane formed during further coalification. Methane formed by maturation of the coal material as it progresses from peat to coals of various rank is the most probable mechanism for the formation of coalbed methane. Most of the methane is adsorbed onto the walls of microvoids in coal. It has been estimated that the surface area of one kilogram of coal is between 20,000 m2 to 200,000 m2. Surface area measurements depend on the coal and also on the method of measurement. At 20 atmospheres, in some coals, the adsorbed methane is 10 times greater than methane as a free gas. At 100 atmospheres the adsorbed gas can be as densely packed as a liquid. The volume of methane gas held in coal depends on the volume of gas that exists as a free gas and the adsorbed gas capacity. The volume of free gas in the coal can be calculated from the kinetic theory of gases (methane can be assumed to be an ideal gas because errors would not be greater than 1 % for normal mining pressures). Langmuir (1916) derived an equation for the adsorption of gases on uniform surfaces and this is applied to the adsorption of methane on coal:

Jan 1, 1993

By A. K. Sinha

Ever since electricity was introduced, electrical injuries and electrocutions have continued to occur regularly in coal mines. An analysis of the two hundred cases of electrocutions which occurred during 1956 to 1970 indicated that over 50 percent of the incidents were caused by the ineffectiveness or lack of electrical grounding. Research shows that various types of arbitrarily designed ground beds are in use and that the ground resistance and current are often very high and subject to wide seasonal variations. The results of a recent research are discussed in this paper.

Jan 1, 1980

By T. W. Healy, W. J. Trahar

INTRODUCTION The flotation of minerals from their ores in flotation cells involves understanding many chemical and physical processes ranging from electronic events in the bulk mineral and in the mineral surface regime. molecular events at interfaces, the statics and dynamics of thinning and rupture of microscopic to molecular intefacial films, the fluid mechanics of bubble- particle events, the dynamics of air-water-solid colloid states in a flotation machine, etc. etc. D.W. Fuerstenau, whom we honour in this symposium has made unique contributions to many of these diverse physico-chemical and technological sub-processes. The present paper is concerned with a number of observations of the behaviour of minerals in flotation cells and the surface science of some mineral sulfide-water systems. We do not intend to be comprehensive in our analysis, but rather to highlight the challenges that face the scientific masochist who chooses to understand "froth flotationn. In what follows, emphasis is placed quite deliberately on technologically relevant, dynamic or realistic flotation processes i.e. the recovery in a froth of a given sulfide mineral particle of a given size and history from synthetic or actual ores in a flotation cell. The paper also attempts to use the understanding that is emerging from the area of photoelectrochemistry of colloidal

Jan 1, 1989

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988

By M. S. Duffy

To exploit the mineral resources of fine grained ore bodies the minerals processing industry is turning to fine grinding technology, of which tower milling has become an established part. However, compared to other mills relatively little is known about the operating mechanisms in tower mills. In all milling processes one of the keys to understanding how they work is in knowing how their grinding media move. To investigate the ball motion in tower mills a glass unit was therefore constructed and measurements taken of the movement of the grinding media. This paper describes the results from this study.

Jan 1, 1998

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By I. Yu. Melekestseva

Two types of hydrothermal massive sulfide fields were discovered in the Mid-Atlantic ridge (MAR) in the last twenty years. The first type associates with basalts and includes the TAG, Snakepit, Broken Spur, Lucky Strike and Krasnov hydrothermal fields. The second type is related to ultramafic rocks and represented by the Logatchev, Rainbow and Ashadze hydrothermal fields. In 2007 a new, probably, the largest cluster of hydrothermal massive sulfide field on the MAR (Fig. 1), related both to basaltic and ultramafic rocks, was discovered at 13°31'N of the MAR (Beltenev et al., 2007). [ ]

Jan 1, 2008

By M. A. Giralico

Solvent Extraction (SX) technology has undergone significant refinements including outright process changes to achieve greater copper production rates with lower organic entrainment levels. LIGHTNIN has completed a detailed study aimed at improving on the conventional Holmes & Narver and Davy Power Gas type impeller designs1 by optimizing the mixing through the use of high efficiency pumper turbines instead of making system changes as others are doing. Since each individual installation requires a different design head and flow, LIGHTNIN has developed the R320 "family" of high efficiency, curved blade pumper turbines. These impellers are designed to maximize head and flow while reducing entrainment through lower power consumption, less shear generation and turbulence, elimination of air incorporation, production of the optimum droplet distribution, and lower tip speeds. These improvements also maintain the required mass transfer and copper recovery of the traditional impeller designs. The R320 impeller benefits have been quantified using Laser Doppler Velocimetry (LDV) and proven in multiple domestic and foreign installations at flow rates exceeding 15,000 GPM. Design comparisons of this improved impeller type versus traditional technology impellers in head, flow, power and entrainment are presented for review. In addition, the inherent benefits of axial flow, high efficiency impellers like the A3 1 0 and A6000 in auxiliary mix chambers will be discussed. The high flow, low shear characteristics of these patented impellers provide the necessary dispersion stability for mass transfer while speeding phase disengagement in the settlers due to low power and low shear input.

Jan 1, 1995

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980

By Akira Usui

Ferromanganese crusts on topographic highs in the western Pacific Ocean are believed to be potential resources of cobalt, nickel and platinum. Earlier shipboard geological and geophysical studies by Japanese organizations have focused on mapping of distribution of thickness and metal contents of the deposits when estimating the total reserves. This paper summarizes our attempt to obtain more feasible data of distribution patterns and configuration of the deposits which are important parameters for resource evaluation at some seamounts in the South Pacific Ocean. Morphology of the seamounts and micro-topography of the sea floors are described using shipboard acoustic remote sensing, deep-tow sonar images, and TV/camera. [ ]

Jan 1, 2008