Search Documents

By M. Kavvadas

Geotechnical design using Factors of Safety recommended by Codes of Practice is based on largely unknown ?margins of safety?, usually without consideration for the importance of the project (i.e., potential consequences of failure) directly or explicitly. On the contrary, probabilistic modelling can be a useful tool in risk management as it provides the means to measure the risk to be managed. This is achieved by calculating the probability of failure associated with a specific design, i.e., by relating the classical factors of safety with the corresponding probability of failure and by using a cost optimization procedure to achieve ?optimal? designs, accounting for the expected costs in case of catastrophic failure. This paper describes the methods used to calculate the probability of failure and its correlation with the classical Factor of Safety using sampling techniques and a simplified method based on the moments of the factor of safety considered as a random variable. These procedures are illustrated in an example which investigates the stability of a slope.

Jan 1, 2005

By W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of freshwater whose origin can be traced to the present and historical courses of the River Indus. In the past the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water-table has risen to within a few feet of the surface. The river system itself is being progressively developed for irrigation and very shortly a situation will arise where the entire low winter flow will be utilised. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilise the water-table at safe depths. This paper discusses some of the methods used to ensure optimum-economic development of the fresh groundwater and describes the general design philosophy evolved by the authors firms for both irrigation and drainage wells, with respect to both well configuation and operation. Water quality standards are discussed in as much as they affect subsequent use of the groundwater. A few particular aspects are considered, including that of the values of the relevant aquifer constants, the construction of wells and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to-produce fresh water from layers overlying saline water. This solution is also discussed.

Jan 1, 1967

"It’s been 80 years since Charles Warman invented the iconic Warman slurry pump, a pump that revolutionized the mining industry and continues to push the boundaries of pump performance to this day.In honor of this legendary brand, Weir Minerals hosted an event at the end of May in Kalgoorlie, Western Australia. Throughout the evening, attendees relived Warman pumps’ history and gained an insight into some of the future innovations planned.“It was a privilege to share this special night with some of our key customers, past and present employees, and members of the Western Australian School of Mines,” said Ricardo Garib, divisional president of Weir Minerals. “Warman is one of our leading brands. It has truly shaped the mining industry over the past 80 years and is a product we are all very proud of. The Warman pump, invented to solve high wear issues in slurry pumping, created a thriving industrial business that is now the cornerstone of Weir Minerals with more than 8,000 people, and more than 150 manufacturing and service centers across the globe.”Always inventingCharles Warman invented the Warman slurry pump in Kalgoorlie in 1938. It was a hardwearing slurry pump that used replaceable liners and a replaceable impeller, something that had never been done before.“Charles Warman was a visionary and an innovator. The use of rubber lining in the pump was groundbreaking as it reduced total ownership costs, was safer to handle and offered extended wear life in many abrasive slurry applications. It is a great example of solving customer problems with material science, and is still taught in universities today,” said Marcus Lane, global product manager for centrifugal pumps at Weir Minerals.It was quickly adopted throughout the goldfields in Western Australia and by the 1950s, as customer demand rose, Warman expanded his business by opening offices in Sydney and Perth.During the 1960s the rapid growth of the business continued with manufacturing and sales outlets established around the world. The Warman Series ‘A’ pump was accepted and became a world leader in its field. Further work on the Warman AH pump resulted in the development of interchangeable metal and rubber wearing components."

Jan 9, 2018

By Marek Niec

Native sulfur deposits in Poland occur in Upper Miocene strata on the northern (platform) border of the Carpathian foredeep. Systematic exploration since 1953 has resulted in the discovery of seven stratifom-stratibound sulfur-bearing limestone deposits that together contain about 0.6 billion tons of demonstrated sulfur reserves and about 0.5 billion tons of inferred and hypothetical resources. One open pit and three Frasch mines are currently in operation; another is under construction and one has been abandoned. Total production is about five million tons per year from ore containing on the average about 25% sulfur. Field, isotope, and micropaleontological data indicate that the sulfur-bearing limestone was formed through the bacterial reduction of gypsum in the presence of methane discharged from source beds and traps in the Carpathian foredeep. Subsequent recrystallization of the sulfur-bearing limestone, tectonic activity, jointing, karstification, and partial leaching of the sulfur has transformed the sulfur deposits and has altered the thickness and content of the sulfur-bearing strata, and their porosity and permeability, affecting the productivity and water consumption of the sulfur wells. Caputerized borehole logging techniques and geostatistical reserve estimates are used in mine planning. Great environmental impact constrains the development of sulfur mines.

Jan 1, 1992

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: • The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. • That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. • Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equip¬ment, blasting, or water infusion. • To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. • As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. • When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in. - diam). The techniques in detail are somewhat complex and sub¬ject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1989

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equipment, blasting, or water infusion. To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in.- diam). The techniques in detail are somewhat complex and subject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1990

By Rashi Tiwari, George Danko, Jeremy Knowles

A control technique is described for enhancing the efficiency of materials handling and other mining operations. The concept involves human-operator and robotics control interactions to assist in mining operations. Many mining tasks require a human operator to coordinate the motion of several machine links by simultaneously manipulating multiple joysticks or other control devices. The new control architecture allows for automatic coordination of multiple machine joints. The machine movement may follow a computer-optimized, learned coordination pattern, while the operator still retains the master control of the overall trajectory and velocity parameters. Examples are described for a surface mining front shovel.

Jan 1, 2005

By Y. Guan

The adsorption of zinc species onto silica in ammonical solutions has been studied. Adsorption isotherms reveal that increasing adsorption occurs as the solution pH is made more alkaline. Fr-IR spectroscopy revealed that the adsorbed species is a zinc ammine complex.

Jan 1, 1993

By H. T. Mulryan

Talc is used as an essential ingredient in a wide variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance, and household furniture components to high performance parts made from liquid crystal engineering resins. The paper focuses on polyolefin applications; the three tier market for talc in polypropylene; the effects of various talcs in typical compounds; and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds which mimic higher cost resins, and polyethylene films, customer requirements for talcs for these purposes are discussed.

Jan 1, 1993

By Satid Therdkiattikul, Donald A. Dahlstrom

Many gold ores are known to be refractory so that conventional cyanide processing will result in serious losses of gold and silver values. A significant percentage of these refractory ores contain aresenopyrite and the gold and silver is usually encapsulated within this matrix as well as the pyrite matrix. Normally the values can be recovered as flotation concentrates because of the sulfide compounds with recoveries of over 90% and at very good grades. In order to free the gold and silver, the sulfide matrix must be destroyed. This can presently be achieved by (1) pressure­temperature leaching (2) roasting and (3) bacterial leaching. All of them have advantages and disadvantages as well as an obviously increased cost for the each processing method. However, the increased gold and silver recovery should and must more than offset this cost. It is believed that gold recovery should be well over 90% from the concentrate so that overall recovery from the ore should be in the 90-95% region. All three processes must consider pollution control of both sulfur and arsenic to prevent contamination of air, water or land through improper waste disposal. This paper will concern only bacterial leaching and its necessary control of effluents and solids. Sulfur does not appear to be a problem as the element is oxidized to sulfate and is precipitated with an acceptable solubility. Other important improvements that must be controlled are arsenic and iron which are present as significant values (1-12 g/1 of arsenic, 20-40 g/1 of iron). In addition much smaller values of base metals, aluminum and magnesium can be present as well as other elements depending on the ore and these must be low enough after treatment to meet EPA regulations.

Jan 1, 1993

By Michael P. Foose

In 1994, more than 41 of the approximately 160 coal-fired, electrical- power plants within the six-state Ohio River Valley region used flue-gas desulfurization (FGD) units to desulfurize their emissions, an approximately 100% increase over the number of plants using FGD units in 1989. This increase represents a trend that may continue with greater efforts to meet Federal Clean Air Act standards. Abundant limestone resources exist in the Ohio River Valley and are accessed by approximately 975 quarries. However, only 35 of these are believed to have supplied limestone for FGD electrical generating facilities. The locations of these limestone suppliers do not show a simple spatial correlation with FGD facilities, and the closest quarries are not being used in most cases. Thus, reduction in transportation costs may be possible in some cases. Most waste generated by FGD electrical-generating plants is not recycled. However, many FGD sites are relatively close to gypsum wallboard producers that may be able to process some of their waste.

Jan 1, 1999

By H. T. Mulryan

Talc is used as an essential ingredient in a variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance and household furniture components to high performance parts made from liquid crystal engineering resins. This paper focuses on polyolefin applications, the three-tier market for talc in polypropylene, the effects of various tales in typical compounds and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds that mimic higher cost resins, and polyethylene films. Customer requirements, for tales for these purposes are discussed.

Jan 1, 1993

By J de Cuyper, V. M. Lovell, W. Freyberger

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysacchar- ides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By N/A

finally, but not least, the staff of Vaal Reefs Chemical Laboratory for their assistance and patience with the introduction of a new technology,

Jan 1, 1991

Disposal of solid and liquid wastes from mining and milling operations has become a focus of attention in recent years. Consequently, the geotechnical engineer is more frequently associated with design of disposal facilities. Jack Wulff, a representative of one consulting firm with experience in this field, talks with ME about the geotechnical engineer's contribution. Mr. Wulff, mine and mill waste disposal today is receiving more attention-and many more dollars-than in the past. Regulatory agencies have promulgated demanding requirements concerning mill waste (especially uranium mill waste) and specialist consultants are frequently being called in to design disposal systems. What can the experienced geotechnical engineer add to the development of waste disposal facilities? It's true that geotechnical engineers have recently become more visible in the minerals sector, but we've been around mining for a long time-as foundation engineers for mills and mine support buildings, and for geotechnical aspects of open pits, pipelines, railroads, roads, and so forth. We've also designed water supply dams, which could be considered recursors of tailings dams and other forms of disposal systems. Let me show by example what geotechnical engineering can contribute to waste disposal facility design. I recently was asked to look at several small wastewater impoundments which had failed. The design of the earth embankments appeared, at first glance, to be rather conservative. They were only about 3.4 m high, the slopes were 3 to 1 (horizontal to vertical), with about 24 m of bottom contact with the earth foundation. But there had been three episodes of dike failure in a few months, all upon initial filling. The problem was the nature of some material in the foundation that was also used as structural fill-a dispersive clay that readily deflocculated and eroded on contact with water, especially with seeping or flowing water. The design did not include the defensive measures required to use such materials confidently in water retention structures. Apparently, the designer did not recognize the potential problem posed by the unusual soil characteristics. That's the sort of engineering information fundamental to geotechnical engineering, but not necessarily a part of the civil, structural, or mining engineer's professional training or experience. This difference in expertise is not simply a matter of factual knowledge-it also affects the design process. The structural engineer can design a structure to fit the client's functional needs and can specify the materials (grade of steel, PVC, concrete, etc.) to meet the demands of the design. The geotechnical engineer's design process is somewhat different, since we work with natural materials, not man-made materials produced according to specification. We first have to establish what kinds of materials are available (usually directly from the chosen site, since importation of materials becomes expensive). Then we determine the engineering properties and characteristics and, finally, design the structure to fulfill the client's requirements within parameters dictated by available materials. In brief, the geotechnical engineer works with naturally-evolved, not man-made, materials and uses design techniques developed to accommodate that fact. Because no two sites are exactly alike in configuration, structural (geologic) characteristics, or available materials, there will be unique design and judgmental questions to be resolved on virtually every project. You said that water retention dams could be considered the precursors of tailings dams-you probably had a specific technical relationship in mind. There's a very strong carryover of methodology from earth dam design, where the technology developed and where it has become very refined. In designing a tailings impoundment or similar facility, essentially the same procedures of field sampling are involved (with a geotechnical engineer or an engineering geologist directing the program since representative

Jan 7, 1980

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

By Ayman A. El‑Midany, Hassan E. El‑Shall, Kerri‑Ann A. Hue

Modification of clays is necessary for the zearalenone (ZEN), as long-chain mycotoxins, removal. The organic-cations were usually used to modify the clay hydrophobicity to accommodate the large mycotoxin molecules. In this study, tri capryl methylammonium (TCMA) chloride and common corn oil were used in clay modification. Several characterization techniques such as XRD, FTIR, and TGA were used to identify the d-spacing changes after modification either by TCMA or corn oil. The results of applying the TCMA-corn oil-modified clays in ZEN removal indicated a noticeable improvement where more than 90% of ZEN could be removed in vitro at acidic and neutral pH values. The success of eliminating a high percentage of ZEN molecules is due to the expansion of intergallery spacing as a result of TCMA surfactant intercalation within the clayforming layers. The removal percentage does not depend only on pH but also on the amount of clay used. In addition, the ZEN removal in the presence of corn oil is better at acidic pH and small clay amount where the ZEN can be fully removed.

Sep 27, 2021

By Hakan Uyguçgil, Beril Bayraktar, Adnan Konuk

In mining, which is one of the industries with the highest risk of occupational accidents, a primary goal is to enhance safety through the thorough investigation of accidents using reliable methodologies. In this research, the data from 13,653 accidents reported in the Karadon Hard Coal Enterprise between 2000 and 2011 were analyzed and compared using the life-table and Kaplan-Meier methods. Accident records were classified and analyzed into four categories: environment-related, equipment-related, person-related and other accidents. Findings in terms of survival time indicate that environmentrelated and person-related accidents had the highest risk in Karadon, with equipment-related accidents having the lowest. This study established the reliability of using survival analysis methods to investigate occupational accidents in the mining sector. Given that environment-related and person-related accidents occur in a relatively short period, such as one year after starting work, it is recommended that research be done to improve workplace and occupational safety measures and broaden the training given to miners. Additionally, it is determined that increasing the use of automation and mechanization in underground coal mines, combined with developing a thorough equipment safety training program to raise awareness of the danger, can help prevent person-related occupational accidents caused by the interaction between equipment.

Feb 1, 2024

By V. K. Kollipara

Dust dispersion characteristics in mine airways are important for developing engineering controls for dust and explosions. Authors here have used CFD modeling approach to analyze the dust dispersion characteristics in mine airways. The technique was initially validated with the published field experimental data. The results obtained were in a reasonable agreement. CFD validation results show that in a single entry the dust concentration decreases exponentially as a function of distance. Finer particles can travel up to a distance of 350-400 m away from the source. Parametric studies indicate that air velocity and input dust concentration has significant influence on dust concentration distribution. CFD modeling was then applied to study the dust dispersion characteristics in a room-and-pillar mine layout. Preliminary results show that dust concentration distribution is highly dependent on the airflow patterns and air velocity distribution. The distribution is not exponential until the velocity in the travel way becomes uniform. Data developed in this study may be used to design mine layouts and engineering controls for dust control and explosions.

Jan 1, 2011

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986