Search Documents

By R. A. Pindred, M. P. Lam

Cyanide is a conventional lixiviant for gold extraction but its' toxicity is a major concern for the environmentalist. There are many alternative non-cyanide lixiviants, such as thiourea, thiosulphate, chlorine and hypochlorite etc., which may reduce environmental sensitivity. This paper will discuss the leaching characteristics of gold in hypochlorite leaching solutions. The dissolution of gold in a hypochlorite solution not only depends on the concentration of the hypochlorite but also on other variables, such as hydrochloric acid, sodium chloride and temperature. The dissolution rate of gold in hypochlorite solution is much faster than other lixiviants. Due to the interference of impurities, gold extraction from an ore under ambient conditions requires large quantities of reagents. However, refractory gold ores may be successfully pressure oxidized in an autoclave at reasonably low reagent levels. Gold extraction to the pressure oxidation leach solution is rapid and complete in one stage, thus eliminating the need for further cyanidation.

Jan 1, 1990

By A. E. Stewart

Slope design in an open pit mine includes determining bench height, bench face angle and berm width. Case histories are presented of two highwall slopes (160 and 220 m or 525 and 720 ft high) excavated in dipping strata in an op¬erating coal mine. These examples illustrate the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in approximately the same lithologic and structural environment. The main differences between the slopes were the angle at which the bench faces were excavated and the excavating methods that were used. Relevent aspects are also described of the engineering geology, slope design and excavation procedures.

Jan 1, 1998

By Donald Lau, Adrian Crawford

In the field of grouting, practitioners fre¬quently advocate procedures that are often unique and contradictory. As a result there has been considerable debate as to what constitutes optimum grouting practice. A knowledge of both the rheological properties and the flow characteristics of grouts is essential to the development of a rational understanding of the grouting process. Flow models and viscosity experiments have been conducted using cement grouts comprising High Early Strength Portland and Microfine cements. The addition of superplasticizers was found to enhance the flowability of the grouts as well as to reduce the effective groutability ratio. Steady state flow equations and design charts for predicting the radial penetration of cement grouts have been developed.

Jan 1, 1986

By Charles E. Weaver

A core from the La Camelia attapulgite mine in north Florida was studied in detail to determine the detailed vertical variability and the relations of the various parameters. The structural, textural, mineralogical and chemical data indicate there are two major depositional cycles represented within the minable interval. The sediments deposited during the two cycle differ in detail but in general are similar. The environments of deposition grade from shallow marine to lagoonal to tidal flat to marsh. The sedimentary structure (lamination, burrows, pebble conglomerate), mineralogy (attapulgite, montmorillonite, sepiolite, dolomite, calcite) chemistry (Al, Mg, Fe) are closely related to each other and their nature is determined by the depositional environments. Most of the clay minerals and carbonate minerals are authigenic and are therefore particularly sensitive to environmental differences. The variability and environmental features seen in this core are characteristic of the sediments in the general attapulgite mining area. A detailed understanding of the relationships discussed should be of value in prospecting, mining and processing.

Jan 1, 1972

By Jerry M. Whiting, Landy A. Stinnett

The subject of this paper is broad and complex. Secondly, it is near and dear to the authors' hearts. Therefore, it doesn't seem possible to deal with every aspect of it in less space than a good size textbook. Also, if we dealt with all of the basics of feasibility studies and report preparation, we would cover a lot of material available in the literature, and would have to minimize our editorial comments. In view of these limiting realities, we have chosen to discuss selected facets of the subject, and to provide several comments which stem from our personal experiences during the past 20 years. "Think Ahead" hen someone is undergoing training to command a large ship, the following short phrase is engraved in his memory: "Think Ahead." The reason is simple enough. A battleship, aircraft carrier or oil tanker cannot change directions quickly, and if one waits to a what the other ship is going to do, there may be twisted metal and bodies scattered all over the ocean floor. The commanding officer has to use radar, forward rind aft lookouts, experience, common sense, intuition, weather forecasts, and everything else available to him to avoid trouble. Remember the USS Stark, and the fate of its captain? The fact the Stark was hit by a "friendly" missile didn't lessen the damage. How about running into a mine? Is it an excuse that no one thought about the possibility of a minefield ahead of the ship? The point is, relative to feasibility studies, that its prospective authors, and especially the commander of the efforts required to create it, must "think ahead" from the moment of their association with 4 mining activity. They must

Jan 1, 1987

By Gösta W. Diehl

During the past five years the use of all-hydraulic drilling equipment has increased rapidly, and we have now reached a point where the hydraulic drill has become an alternative to be seriously considered for every drilling operation. The hydraulic drills have many advantages over pneumatic drills, but they also have certain characteristics, which makes a potential user hesitate before making the switch. And when the decision to use hydraulic drills has been made, the user then faces another choice of equal difficulty: the choice between different hydraulic systems. This paper discusses some of the factors to be taken into account when considering hydraulic drilling equipment for rapid tunneling in hard to medium hard rock. THE CHOICE BETWEEN HYDRAULIC AND PNEUMATIC EQUIPMENT The choice between a hydraulic and a pneumatic drill is much more than just that: It is a choice between two different systems. The choice is usually based on the productivity, economy or ergonomy of the system. However, also other factors should be considered, such as service capabilities and training requirements. And finally the choice will be influenced by the need to acquire know-how in the new technology. Productivity If the prime consideration is to achieve the highest possible tunneling speed, then the high penetration rates of the hydraulic

Jan 1, 1979

By M. Makarenko

The sandstone type Devladivske uranium deposit is located within the limits of Eocene pale-ovalley filled with alluvial sediments. Mineralization with uranium content up to 0.1% forms several ore beds divided by redox barriers. In the period 1962-1983 the deposit has been exploited over an area of 918000m2 by in situ leaching (ISL) using drillholes with a depth between 35 and 100m. During mining operation about 200,000 t of H2SO4, 6,300 t of HNO3, and 15,000 t of NH4NO3, have been pumped in the ore body. In 1983, the groundwater pollution aureole had a length of 4.5 km and a width of 400-600 m. There is a hydraulic connection between the uranium-bearing aquifer and both the upper and lower ones. The technological solutions used for ISL caused partial contamination of these horizons. After mining completion, dilution of the residual technological solutions with "pure" natural waters took place through gaps in impermeable sediments between aquifer horizons. Calculation of self-purification process kinetics shows that the sulfate ion pollution aureole will disappear approximately after 120-150 years at a distance up to 2.0-2.5 km from the western margin of the deposit. This means that there is no risk for contamination of the river Saksagan? that flows at a distance of 17km from the deposit.

Jan 1, 2005

By Alfred Haack, Günter Girnau

INTRODUCTION From 1967 to 1976 in the Federal Republic of Germany about loo km tunnels and 125 underground stations were constructed for municipal and commuter railways solely. Additional a remarkable amount of road tunnels and sewers were built. In 1977/78 a further 27 km railway tunnels, 3.5 km road tunnels and 65 km sewers and utility lines were under construction. This shows an enormous volume of tunnel construction work. In connection with this activity various technical research and development programmes have been carried out. They deal with nearly all fields of underground works as for example soil and ground exploration, excavating and lining techniques, calculation and last but not least waterproofing problems. It is impossible within the framework of this report to touch on all the problems. Therefore, only one problem area with its different aspects will be discussed: waterproofing systems and their last developments in Germany, especially, joint sealing with special consideration of the waterproofing of concrete segmental tunnel lining (1)

Jan 1, 1979

By Ronald E. Yarbrough, Theodore L. Triplett, Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from a high-extraction retreat room-and-pillar operation in southern Illinois. The objective of this monitoring program is to study the inter- action between the ground surface and a structure during a subsidence event. Data from such a study should enhance the understanding of the mechanisms that produce structural damage and aid in the design of structures that resist such damage. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tiltmeter to detect and follow the tilt of the foundations caused by the mining subsidence sequence is demonstrated. Using data from this tiltmeter, the development of curvature in the foundations as they conformed to the displaced ground surface is shown. This curvature is rep- resented by differences in tilt at various points on the foundations, indicating a change in tilt over a horizontal distance. Also, even though subsidence damage has not been fully analyzed, preliminary observations of the cracks that formed in the foundations are reported. These cracks resulted in the separation of one footing into distinct pieces; therefore, their effect on the tilt readings is cited.

Jan 1, 1986

By Sizhe Tan

An open pit mining operation can be considered as a production system with at least two products: ore and overburden (waste). A primary mine planning task is to schedule the production of ore and waste over its life span subject to several technical and economic constraints to maximize some objective such as the overall profit from the operation. Two major constraints are (i) the feasible combinations of ore and waste productions and (ii) the limiting function for ore production as a function of mine life. The task in scheduling production and stripping ratio (ratio of waste to ore production) is to find an ore production curve below the upper bound function of ore production, and a stripping ratio curve within the feasible domain of ore production and overburden removal while maximizing the defined objective. Zn this paper, feasibility of developing computerized optimization models to perform such a scheduling process is explored. Two optimization models are proposed for the task. In the first approach, a linear programming (LP) model is employed and in the second, a dynamic programming procedure (DP) is outlined. In these models, in addition to the consideration of the two major constraints mentioned earlier, various other contributing factors such as interest rate, equipment purchase cost and installation schedule, operating cost, and equipment idle cost are incorporated. An example is provided to illustrate the LP model application.

Jan 1, 1992

By David W. Wisecarver

Kennecott Copper Corporation and the U. S. Bureau of Mines cooperated in a full-scale slope stability research project at the Kimbley Pit near Ely, Nevada. The west wall of the Kimbley Pit was mined from an over-all slope angle of 45° to an over-all slope angle of 57° and the pit was deepened nearly 50 feet. Mining was begun February 10, 1966, and completed October 30, 1966. Approximately 2.55 million tons of ore and waste were mined. The project was designed and carried out to learn more about the behavior of a pit wall as its slope angle is steepened and to obtain a possible insight into engineering parameters for use in design of future slopes. Data from this project are presented as obtained from (1) instruments installed in two adits for deformation and displacement measurements, (2) a subsidence network installed on the surface above the steepened wall, (3) pre- and post-mining observations of stress in rock, (4) sonic-velocity measurements, and (5) seismic and microseismic investigations. Changes occurred in measured quantities as the slope was steepened but stopped when mining was completed. Agreement was noted between the measured changes and predicted changes obtained from calculations using the finite element technique. Subsidence surveys and microseismic studies show the steepened pit wall to be stable.

Jan 1, 1968

By T. Negeri

The simultaneous use of two or more families of collectors can sometimes improve one or more key flotation performance indicators, especially if the ore under consideration contains several minerals bearing the same metal. The maximum amount of collectors that can be used is limited by the need to maintain a high concentrate grade and selectivity. Therefore, when more than one collector is required, an experimental design that allows variations of both the proportions and the amounts with respect to other process factors has to be selected to find the optimum dosage. This type of design is known as "process factors in mixture amount experiment". It is a powerful design suitable for discovering the existence and evaluating the magnitude of the interactive effects between various flotation parameters. This paper elaborates the principles on which such a design is based, and demonstrates its usefulness with a case study.

Jan 1, 2003

By A. N. Papadopoulos

The life cycle assessment and the performance of pine fence posts treated with water borne preservatives and oils after 18 years exposure in ground contact were examined in this study. Vacuum CCB treated fence posts were subsequently treated at their lowest part (ground contact) with creosote using the open hot and cold tank process and exposed under warm dry temperate climatic conditions in Greece. After 18 years exposure, samples were taken from the above ground contact, top, middle and ground contact and tested for toughness using a Denison single blow impact bending test machine. There was no significant reduction of toughness in any of these zones. Chemical analysis of the residual CCB of unexposed and exposed samples by ICP showed that copper and chromium losses were insignificant while boron losses were significant (more than 50% of the initial content). This was attributed to an effect of creosote treatment.

Jan 1, 2008

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

By Jim M. Johnson

INTRODUCTION The facility water balance and maintenance of sufficient excess storage volume in the solution control system are often amongst the most critical facets of design and operation of heap leach facilities in cold, snowy climates. The purpose of this paper is to summarize and discuss climatic and operational factors which have a significant impact on heap leach water balance evaluations in high snowfall climates. Example water balance simulations are presented for proposed heap leach projects located in areas subject to high snowfall in the northwestern United States. The climatic data input to these simulations represent both net evaporative and net precipitation climates. FACTORS AFFECTING WATER BALANCE EVALUATIONS The combined effects of seasonal operations, re1atively low evaporative losses, and potentially large inflows to the solution control system from snowpack and spring storms require an enhanced awareness of the factors which impact facility water balance. Unlike operations at mines in more arid climates, seasonal excess water rather than a shortage of make-up water is the rule. A thorough understanding of a number of factors, including regulatory constraints, climatic influences, and impact of operating philosophy and techniques, is critical to successful development of an incident-free heap leach operation under high snowfall climatic conditions. A process water circuit schematic for a typical heap leach operation is shown on Figure 1.

Jan 1, 1988

By Tony Stephens

In this paper I will try to give an overall picture of the use of pure oxygen in gold leaching in South Africa. Pure oxygen has been overlooked as a reagent for many years. Only with the increased sophistication of gold plant instrumentation, greater recognition of the technical abilities of the plant management and a more definite attitude towards plant efficiency has the recent break-through been achieved. There are, today, twelve plants using pure oxygen in this way as a permanent part of their operation and another three or four presently carrying out long-term evaluations. I believe that this number will double over the next few years as more and more plants identify potential benefits. I have, therefore, set out to look at the background and chemistry behind these innovations, describe the various methods available to dissolve oxygen, briefly look at the laboratory and trial work carried out by ourselves at Afrox and then the different installations, both ours and those of our competitors.

Jan 1, 1998

By John A. Shuster

Case histories are reported for several soft ground shafts ranging from 6' to 40' in diameter and 50' to 230' in overburden depth for which ground freezing was employed to provide temporary ground support and groundwater control during shaft sinking through the overburden. Cases reported emphasize dealing with difficult site and ground conditions such as working within existing buildings, through very soft, running and bouldery soils, in the presence of substantial lateral groundwater flows, and into salt dome deposits requiring special considerations. Construction procedures, schedule, and relative costs are discussed for each case.

Jan 1, 1985

By Glenn A. Gruber

The conditioning of phosphate flotation feed with anionic flotation reagents was identified as a high- priority research topic during a beneficiation work- shop sponsored by the Florida Institute of Phosphate Research (FIPR). FIPR subsequently solicited research proposals to identify the mechanisms of reagent adsorption, to determine scale-up relationships for conditioner design, and to investigate the effect of conditioning variables on reagent adsorption and flotation performance. The two-year research project was awarded to Jacobs Engineering. Somasundaran, Inc., the University of Florida Mineral Resources Research Center, and the U.S. Bureau of Mines assisted Jacobs. Two mechanisms of anionic collector adsorption were detected by spectrographic analyses and confirmed by microcalorimetric measurements. The mechanisms provided a sound technical basis for the empirical practice of conditioning phosphate flotation feed at a high percent solids. Tests performed in laboratory and pilot-scale agitated tanks indicated that power intensity may be used as a reliable scale-up parameter for anionic conditioning of phosphate slurry. Excessive agitator speed during conditioning was found to be detrimental to anionic flotation performance. Some dimensional ratios of anionic conditioners were found to be consistent with good utilization of agitation energy. Laboratory conditioning and flotation tests demonstrated that adsorption of collector onto phosphate and the subsequent recovery of phosphate in anionic flotation were significantly influenced by the quantity and quality of water used in conditioning. Conversely, the quality of water used in flotation was more influential on the recovery of quartz in the concentrate. A comprehensive survey of anionic conditioners and conditioning practice in the Florida phosphate industry was also performed during this project. The study clearly showed that flotation testing with laboratory conditions typical of scientific research gives different results than laboratory testing with simulated plant conditions. The effects of test conditions on laboratory test results should be carefully considered by investigators planning and conducting applied research.

Jan 1, 1999

By Jorgen Elbrond

Before and in the early stages of industrialization, mining was the undisputed leader in technology. It represented the high-tech of the time. Early mechanization bears witness to that. Hoisting and rock breaking driven by waterpower are such examples. The mines' use of the steam engine was a major incentive to its development. By these means new mines could be opened and more metal supplied. Understanding of systems was essential for miners when shaping the infrastructure of the mines for the transportation of ore, material and men and for the evacuation of water and for ventilation. The irrigation systems of ancient mines are such examples. However, with the industrial revolution other more specialized branches of industry advanced further, and the mines became users of other industrial branches technologies. The mining industry had, however, always been quick to recognize a good thing and use it, when time was right. But, compared with other branches of industry, the mining industry has the disadvantage of working in a rugged environment with (and actually inside) a raw material which is abrasive and highly variable with respect to mechanical properties. This determines the rather high unpredictability of mining machines' performances and their low availabilities and explains a part of the delays in introducing technological advances.

Jan 1, 1989

By Hugo J. Garcia, M. C. Fuerstenau, D. M. Lupan, J. L. Hendrix

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. The anaerobic cyanide biodegradation showed good, short-term removal of cyanide in the presence of nutrients (medium A). This system retained metabolic activity at cyanide concentrations up to 300 ppm at pH 10.5. Microscopic examination of stained specimens revealed that the bacteria were Gram-negative, rod-shaped bacilli. Strains capable of cyanide decomposition were identified as Pseudomonas and Alcaligenes. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. Studies with Na14CN showed that 17 % of 14C transformation went into the cells, 18 % into carbonate and 47 % into bicarbonate.

Jan 1, 1995