Search Documents

By E. Suoninen, K. Laajalehto, L. Kartio

Efficient separation of pyrite from other sulfides is of great importance for the metallurgical performance of flotation processes. In this work Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) were used to study the surface chemistry of pyrite in depression, activation and xanthate adsorption under conditions of controlled potential. Modifications of pyrite surfaces after treatment with depressants (lime, sulfur dioxide, sodium cyanide) and after activation with metal ions (Cu, Pb) were studied. The principal adsorption product identified on pyrite was dixanthogen whose formation started at about +0.15 V and +0.25 V (vs, SHE) in ethyl and amyl xanthate solutions, respectively. Copper xanthate was formed on copper(II) activated pyrite. Activation mechanism of pyrite by copper(II) salts is likely to be electrochemical where copper occurs as copper(I) on the surface of pyrite. Effective depression is achieved by sulfur dioxide and sodium cyanide. Depression at high pH is due to formation of iron(III) hydroxides. Calcium ions do not affect the electrochemistry but adsorb on pyrite and reduce the surface sites for dixanthogen adsorption.

Jan 1, 1995

By Regina N. Tempel, Timothy E. Eastep, R. Craig Ford, Bryce R. Roming, Geoff Clothier, Maggy F. Lengke

The Climax Mine, near Leadville, Colorado treats acid drainage in a lime neutralization chemical treatment system. Chemical treatment has been successful in reducing the concentration of metals to below surface water discharge effluent limits, but lime usage has not been optimized. A geochemical modeling approach has been developed to increase the efficiency of lime neutralization. The modeling approach incorporates two steps: (1) calibration, and (2) calculation of amount of lime needed to increase pH and remove metals. Results of our work quantify the lime treatment process and improve our ability to predict overall water quality.

Jan 1, 2000

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By M. Yavuz

Decision Making (DM) can be defined as a selection process of the best one among the alternatives sets in order to obtain goal, and mostly has an uncertain situation [7]. Every mining engineer is subjected to a number of mining DM problems in daily mining operations. In reality, all stages of mining have its own DM problems. Most of time, engineers do not use scientific methods for DM problems. These problems can mostly be solved by the engineers according to their past experiences and practical studies. Mining engineers often use their intuition in DM process. Experience and intuition have been central to DM because of the frequent lack of quantitative data including geology, grade distribution and ground condition, as well as environmental, social and economic factors [8]. In decision process, linguistic variables become in question and decision makers may not know how these variables are computed [9]. So, the DM process may be qualitative, quantitative or combination of the two. The problem structuring and analysis process is conceptualized in Figure 1 [8]. The qualitative analysis is based primarily on the judgment, knowledge and experience of an expert (or team of experts). In a quantitative analysis, the focus is on facts and the data associated with a problem and a mathematical formulation that encompasses the objectives, variables and constraints of the particular problem. The quantitative analysis has traditionally been the subject of operation research and management science [8].

Jan 1, 2008

By D. B. Ogbenlowo

A major problem facing the Nigerian Mineral Industry today is flooding in its underground mines. Flooding has reduced productivity to a very low level which results in huge economic losses. Consequently, this paper presents a computer based model that pre¬dicts the quantity of water accumulating from diverse sources in an underground coal mine with a view to suggesting a permanent solution to the problem. Specifically, the paper describes the model building technique and the output achieved from its application to a real mine case study.

Jan 1, 1988

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The integrated grouting method, as developed in the USSR, can be applied to multi-purpose operations that in¬clude the construction of shafts, drifts, and tunnels. In the USSR it has been used extensively for primary and final grouting of underground excavations in mining engineering and civil engineering projects. It has been applied in projects where the primary objective was waste contain¬ment. It has also been used to control subsidence beneath buildings located over mined out openings and to eliminate the flow of ground water beneath and around dams. This chapter considers several industrial applications in the form of case histories. The word integrated means that grouting activities were integrated with other activities. 9.1 CASE HISTORIES OF GROUTING FRACTURED ROCK WHEN SINKING VERTICAL SHAFTS The integrated grouting method has been applied most widely in the sinking of vertical shafts in fractured, satu¬rated rock. As explained previously herein, grouting oper¬ations preferably are carried out from the ground surface where they are integrated into the schedule of the setting up of the shaft excavation and construction equipment. Such integration reduces significantly the length of time required for preparation of shaft construction and the time required to sink the shaft. The increased efficiency is achieved by the elimination of cementing operations from the working face upon the penetration of each aquifer. Concomitantly, labor and energy consumption during shaft sinking are minimized because the more complicated and labor-intensive work is carried out at the surface section. Table 9.1 presents the essential parameters for the pri¬mary grouting of saturated fractured rock carried out by the integrated method when sinking vertical shafts. 9.1.1 NAGOL'CHANSK MINE NO. 1-2, VENTILATION SHAFT NO. 1 The integrated method of grouting saturated fractured rock through holes drilled from the surface was employed for the first time during the sinking of vertical shaft No. 1 at the Nagol'chansk mine No. 1-2 in the Don Basin. The shaft had an inside diameter of 6 m. The grouting operations commenced by using cement grout with a density of 1.7 to 1.8 g/cm3. Clay-based grout with cement and other addi¬tives was used only for grouting the aquifers where cement grout proved to be ineffective. By the time of the grouting of ventilation shaft No. 1, hydrodynamic analytical methods were well in hand and a preliminary method for designing isolation curtains had been developed. A method for designing and drilling ori¬ented directional drillholes whose natural curvature re¬flected the characteristics of the fracturing had been devel¬oped. The majority of the necessary equipment had been developed. Clay-based grouts were considered ready for the first industrial application. The hydrogeologic environment at the Nagol'chansk mine No. 1-2 contained many prolific aquifers. According to monitored drillhole data, the total expected inflow into ventilation shaft No. 1 without grouting was 425 m3/hr. This large ground water inflow rate was supported by in¬formation obtained during the sinking of the main shaft and from the auxiliary shaft of the "Nagol'chansk" mine No. 1-2. The construction contractor at the site began sinking ventilation shaft No. 1 to a depth of 217 m by cement grouting from the working face of the shaft. As a result of the cement grouting operations, the inflow of water was reduced from 105.4 to 40 m3/hr over this 217 m interval. However the residual inflow rate caused the shaft to become functional at the depth of 217 m. At this point all grouting operations were transferred to SPETSTAMPONAZHGEOLOGIA (STG) in an effort to improve the operation. In order to carry out preliminary grouting from the sur¬face, seven drillholes were installed and designed for re¬ceiving grout. Drilling was implemented by the ZIF-1200A rig to the design depth of the shaft. The geometry of the principal fracture system that would be encountered by the shaft was estimated while breaking ground using informa¬tion from other shafts. The drillholes were arranged so that they cut through the aquifers uniformly around the shaft. Some preference was given to intercepting the aquifers that were located along the rock dip above the shaft bottom because it was established that the ground water in the aqui¬fers flowed downward along the dip into the cone of de¬pression of the shaft. Investigations in the drillholes using the DAU-3M flowmeter described in Chapter 3 showed that all of the nine aquifers were penetrated by the time a depth of 690 m had been reached. The flowmetric information showed that aquifer numbers [1 and 2], [4, 5, and 6], and [7 and 8] had practically identical hydrogeologic characteristics; so it was decided to connect them into combined stopes and inject the grout using five stopes instead of nine. Table 9.2 shows the results of the grout injection into the aquifers. The volume of grout pumped into the separate intervals through single holes varied from 204 to 15 m3. The trend of grout consumption showed a reduction of grout consump

Jan 1, 1993

By C. B. Manula

The Crushed Stone Industry plays an important role in Pennsylvania's mineral economy. During 1965, the total production of crushed and broken stone in the United States reached 780 million tons from which 57 million tons were produced in Pennsylvania (Mineral Industries Surveys, 1966). It is further significant that Pennsylvania is the nation's leading crushed stone producer. Future trends in stone production will quite likely parallel those in the construction industry. Stone and stone products are finding greater and more varied uses each year. Continued record expenditures for structures such as dams, highways and buildings are the prime reasons for this accelerated growth in demand. Completion of the interstate road system and the maintenance of Pennsylvania's already expanded highway system form the essentials for this expanding market.

Jan 1, 1968

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By Ann M. Gosier

Over the past 20 years, diesel-powered equipment has been introduced into the underground mining environment in increasing numbers. While the introduction began years earlier in the metal-nonmetal sector, the exponential growth in coal mining use during this time has been more pronounced. Reasons for the continued use and rapid growth of diesel equipment in underground mines are easily understood. The safety and operational advantages afforded by this equipment in production and support systems are demonstrable. As other mine operators witness the advantages enjoyed by their competitors, they too move to introduce an increasingly diverse array of such equipment into their underground mines. As with any industrial technology, the use of diesel-powered equipment entails potential safety and health concerns. Existing Mine Safety and Health Administration (MSHA)approval regulations (30 CFR Parts 31, 32 and 36) apply only to diesel locomotives and mobile diesel-powered equipment for noncoal mines. In the absence of specific regulations, MSHA has required the use of equipment approved under Part 36 (gassy noncoal mines) for areas of underground coal mines where permissible electrical equipment is required. However, a considerable amount of diesel-powered equipment without explosion-proof or fire prevention features is in use in areas of coal mines where permissible electrical equipment is not required. It is on the use of this latter class of equipment that MSHA is focusing much of its regulatory attention relative to coal. The agency also is focused on revising existing occupational exposure limits for gaseous emissions and instituting limits on diesel particulate emissions for both coal and metal-nonmetal mines.

Jan 1, 1993

By Ma Fangyuan, Li Min, Xu Bing, Xian Yushuai, Zhao Tonglin

The study explored a new combination amine collector (XK-28) that can obtain better flotation index and defoaming rate for magnetic iron ore. A pure quartz mineral test indicates that dodecylamine, XK-I, or XK-II has good collection effect on quartz and their best flotation pH is in the range of 6–7. The experimental results of a combination collector (XK-I:XK-II = 2:8.) show that the separation effect for quartz and magnetite is better than that of a single collector. The single factor for actual mineral test shows that when the combined reagent is used as the collector, the best conditions are pH = 7, 90 g/t dosage, and XK-I:XK-II = 2:8, which is consistant with the pure mineral test. The difference for dodecylamine as a collector is that the optimal dodecylamine dosage is 60 g/t. Under the best conditions of actual ore test, dodecylamine and XK-28 are respectively used as the collector to compare the flotation indexes. Study results indicate the magnetite grade using XK-28 as the collector is higher by 3.02% than that of using dodecylamine, recovery is increased by 1.92% over that of using dodecylamine. Based on the measurement results of zeta potential, uses of XK-28 can slightly increase the zeta potential difference of quartz and magnetite to enhance the flotation effect. The mechanism of action between the XK-28 collector and the actual ore from the Gongchangling plant is physical adsorption, and this adsorption also has hydrogen bond formation. Contact angle results shows that XK-28 improves the hydrophobicity of quartz better than dodecylamine. Compared with dodecylamine, XK-28 is more sparsely arranged on the surface of the foam. The foam produced by the XK-28 collector has better air permeability and it is more likely to merge and disappear with bubbles.

Jul 21, 2021

By M. Sagisaka

The purpose of this study is to obtain carbon dioxide emissions by copper production systems and quantitative merit to use copper scraps in Japan. Electrolytic copper and sulphuric acid originating from the refining gas are produced in the system. In this study, the inventories such as the fuel consumption of the unit processes and the in-house electricity generation were obtained from published papers and public statistical data. The following observations were made based on the Life Cycle Assessment (LCA) method: (1) Carbon dioxide emissions from the production of electrolytic copper and sulphuric acid in the system are about 1.0 kg and 0.4 kg/kg-product respectively. The carbon dioxide emissions attributable to the transportation of copper concentrate correspond to 20% of the total emission. This emission is higher than that of zinc because the metal content in the concentrate is lower than zinc. (2) The carbon dioxide emissions from the system decrease with the recycling of copper scrap to the converting process because the consumption of copper concentrate is reduced. The reduction is estimated to be 0.18 kg-CO2/kg-Cu at the point of 0.1 kg-scrap/kg-blister Cu. This corresponds to 9% reduction for the present system. However, this recycling leads to the decrease of sulphuric acid by 450x103 tonne at the point. The recycling of scrap should be evaluated not only from the reduction of carbon dioxide emissions, but also in terms of sulphuric acid demands as well as advantage of waste management.

Jan 1, 2003

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By MYRIAM FRANCOEUR, JOHN R.R. BOWLING, ADAM MCFADDEN

As duct-fan systems push the envelope of power, length and cost, their design calls for a more comprehensive technoeconomic analysis to ensure they deliver the expected results without failure and cost overrun. This work explores the numerous factors to include in the design of an extensive (semi-)rigid duct-fan system. Besides delivering a given airflow, the system must satisfy component limitations and power constraints during its lifetime. We evaluate the assumptions underlying the positioning of in-line booster fans in a long gapless duct-fan system and propose a strategy for specifying the location and blade pitch of successive booster fans to prevent system failure due to a partial vacuum.

Oct 1, 2022

By J. B. Yianatos, G. S. Dobby, J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

The question is posed as to why columns typically have a collection zone 10 m high (H) by 1 m in diameter (D). Three geometry dependent factors are considered: degree of mixing, Np; volumetric bias rate, B; and volumetric gas rate, G. Increasing H:D decreased Np and B, which improves performance but decreases G, which causes the column to approach overloading. Taking typical column operating conditions, it is concluded that a collection zone H:D of 10:l is a reasonable compromise.

Jan 1, 1987

By T. Eisele, T. Weldum, G. Rajala, H. Walqu, S. Kawatra

The throughput and energy efficiency of comminution circuits is reduced when ore characteristics change, causing bottlenecks in some portions of the circuit while leaving excess capacity in others. The results of analysis of three years of daily grinding circuit operating data for a full-scale plant has shown that the location of bottle-necks in the circuit will change depending on the nature of the feed ore. The circuit tends to be limited by the primary mill capacity when the ore hardness increases, and limited by the secondary mill capacity with softer ores. Two methods are considered for shifting load in the circuit to relieve bottlenecks by taking advantage of excess capacity in other parts of the circuit: 1) Addition of supplemental comminution operations, such as high-pressure grinding rolls, to process specific size fractions that are not handled efficiently by the primary mill; and 2) Use of screens to shift grinding load upstream from the secondary mills back to the primary mills. In the case of the plant examined in this study, it was found that 58% of the time there was sufficient excess capacity in the primary mills that the throughput of the circuit could have been increased by using screens to shift the grinding load from the secondary mills to the primary mills.

Jan 1, 2004

By J. A. van Huyssteen, P. H. Radcliffe

With the profit squeeze of recent years and indeed the survival of many mines at risk due to low gold prices and declining grades, many inventive solutions have been found of increase production and decrease cost. One of these is the application of process auditing methodology which is essentially a tool to determine systematically whether a process is delivering optimally and, if not, to identify the basic causes. Then a prioritized action plan can be developed with the client. Our experience has shown that problems are seldom what they appear to be and that most processes can operate far more efficiently with relative little effort. A process auditor requires good facilitation skills to overcome initial suspicion, and for sustainable solutions client involvement is essential. Process auditing as it is being applied in Anglogold has evolved over many years to reach its current format. The lessons learned and insights gained in the process are shared here with the reader.

Jan 1, 1999

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By D. Mannino, M. Townsend, E. Daniloff, E. Petsonk

Nonspecific airway hyperresponsiveness is a central feature of chronic obstructive pulmonary disease and has been associated with atopy in the presence of environmental exposures such as smoking. Coal miners may develop emphysema and lung function decrements related to their dust exposure. To investigate the roles of airway responsiveness and atopy in these effects, we evaluated the relationships among smoking, a history of hay fever or seasonal rhinitis, and airway responsiveness (AR) in a group of underground bituminous coal miners and nonmining controls. All subjects had a normal baseline percent predicted FEV1. Increased airway responsiveness was defined as a 15% or greater decrease in FEV1 following methacholine inhalation. 85 miners (45%) and 99 controls (46%) were current smokers, 59 miners (31%) and 55 controls (26%) were lifetime nonsmokers; former smokers were excluded from further analysis. Overall, 25% of 144 miners included in this analysis had increased AR, as opposed to 29% of 155 controls. Thirty-seven percent of both miners and controls had a history of seasonal rhinitis. Significantly fewer miners (15%) had a history of hay fever compared to controls (25%, p< 0.05). Figure 1 shows the prevalence of increased airway responsiveness in miners and controls in association with hay fever. In both smoking and non smoking miners the presence of a hay fever history was significantly (p < 0.05) associated with a higher prevalence of increased AR. Little effect was seen in smoking (p = 0.827) and nonsmoking (p = 0.940) controls. Figure 2 shows a similar higher prevalence of increased AR associated with symptoms of seasonal rhinitis in the mining group. This was significant (p < 0.01) only in the smoking miners. No effect was noted in the controls. These data suggest that the association of a history of hay fever or seasonal rhinitis symptoms with increased airway responsiveness may be more common in coal mining, compared to non-dusty occupations. Although the implication of these data are unclear, further study of miners with a history of hay fever or seasonal rhinitis is warranted. (Supported in part by Grants G1135142 and G1105142, US Bureau of Mines, Generic Mineral Technology Center for Respirable Dust)

Jan 1, 1991

By D. M. Cregger, J. L. Rosenblad, R. E. Ranken

The construction of a large span, high-walled underground opening in a low strength shale rock is unprecedented. The feasibility of constructing a pumped storage project with several tunnels and a large underground powerhouse in low strength shale rested largely on the feasibility of building stable openings large enough to accommodate the required equipment. Because of the lack of experience with large openings in shale, the decision was made to excavate a test adit and test chamber and conduct a multi-faceted geotechnical evaluation program designed to yield pertinent in-situ data on the ability of the shale to accommodate a large underground opening. Factors considered in the shape, size, orientation, and location of the test chamber were: (1) similarity to the anticipated powerhouse chamber, (2) nature of the most important data to be obtained, (3) feasibility of construction, and (4) economics.

Jan 1, 1983

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department&apos;s Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978