Search Documents

By Pierre J. Goossens

Since Guild 1 and Snelgrove 2 attracted our attention to the relationships between certain endogenic ore deposits and plate boundaries, an abundant flow of papers appeared in the metallogenic literature concerned with this problem and its application to mineral exploration. Some of the papers only speculate with the formation of specific type of ore deposit 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 Other papers are more concerned with genetic and structural relationships between plate tectonics and mineralization 13, 14, 15, 16, 17, 18, 19, 20 They are philosophical, in that they are generalized and refer to no specific area. Yet it is true that a large part of the world mineral potential is concentrated at the convergence of oceanic and continental plates, for example, around the Pacific. Therefore, the interaction of two plates by either subduction, obduction or slippage likely has an important role for the genesis and/or the (structural) control of these "orogenic" ore deposits. If subduction is the driving mechanism for the generation of igneous rocks 21, 22 and endogenic ore deposits 18, volcanic activity and the nature of volcanic products certainly are the major geologic processes and events to be tested. Fonteilles 23 and Alsac 24 have already emphasized the important relationship between mineralization and the talc-alkaline affinity of the volcanics. The Andean orogen is one of the best areas for testing such genetic relationships. Rich and varied endogenic and volcanogenic ore deposits occur there and plate interaction is still active.

Jan 1, 1975

By E. Woodburn, R. P. King, R. Putman

Flotation plant simulation, a relatively recent methodology in mineral processing, is defined and corresponding uses are discussed. Typical simulation structures are compared. Current problem areas exist although these are not insurmountable. Following a brief state of the art discussion, the N. I. M. simulation program is reviewed. In general, digital plant simulation is expected to be of substantial benefit in the near future.

Jan 1, 1976

By Chris Ashton, Andreas Rädle, Taner Aydogmus

"The Contract C310 is part of the current biggest infrastructure project of Europe “Crossrail” which is a major new cross-London rail link project and comprises the construction of the North Woolwich Portal, Plumstead Portal and the twin tube Thames Tunnels with a length of approximately 2.6km. Two Mix-Shield TBMs (Diameter 7.12m) were driving through differing challenging ground conditions (Thanet Sand, Gravels, Flint and Chalk) below the ground water table. The two tunnels were underpassing several listed buildings, sensitive structures, operational railway tracks with low overburden and close to existing subway tunnels in an urban environment. Several additional measures as compensation grouting, micro piles and an intensive monitoring has been carried out to ensure a safe tunnelling process. PROJECT OVERVIEW CROSSRAIL Project Crossrail Crossrail is currently the biggest infrastructure project in Europe which has been developed to serve London and the southeast of England. The project includes the construction of twin-bore tunnels on a west-east alignment under central London and the upgrading of existing National Rail lines to the east and west of central London. The new rail track, as shown in Figure 1, starting in Shenfield/ Abbey Wood in the east of London and ending in Reading / Heathrow Airport in the west of London, includes the construction of nine central area stations, providing interchange with London Underground, National Rail and London Bus services, and the upgrading or renewal of existing stations outside central London.Altogether there will be 118km of new rail tracks, including 42km of tunnels and 40 train stations. After completion in 2018, Crossrail expects 200 million passengers per year (Tauriainen, Rädle, Ingram 2013)."

Jan 1, 2016

By S. K. Kawatra, H. J. Haselhuhn

"Fine-grained hematite ore can be concentrated by the process of selective flocculation and dispersion, which relies on proper reagent selection and control of water chemistry. While many previous studies have been performed analyzing the effects of different reagents on this process in a laboratory environment, this paper focuses on investigating the water chemistry within the process in a pilot-scale continuous deslime thickener.The pH, sodium concentration, calcium concentration and magnesium concentration were varied to determine their effects on the iron concentrate grade and recovery, and the phosphorus concentrate grade and rejection in the pilotscale selective deslime thickener. The ideal pH for the iron grade and recovery of the process using a starch selective flocculant was found to be 10.5. Phosphorus rejection, however, was increased at lower pH values. Minimization of sodium concentration was shown to improve iron grade, iron recovery and phosphorus rejection. Calcium acted as a nonselective flocculant showing higher iron recovery, lower iron grade and lower phosphorus rejection with increasing concentration. Conclusions could not be drawn from the experiments that varied magnesium concentration.The zeta potential of the solid-liquid interface of particles in each sample taken was also analyzed to show relationships between zeta potential and process performance. In all cases, a maximization of the magnitude of zeta potential correlated with increased iron grade and recovery. This supports the hypothesis that a higher level of dispersion enhances the selective flocculation and separation process.IntroductionThe United States produced 53.2 million metric tons out of the 3,000 million metric tons of concentrated iron ore produced worldwide in 2012 (Tuck, 2013). With this in mind, there has been a large increase in iron ore processing research (Bolen, 2014; Carlson and Kawatra, 2008, 2013; Halt and Kawatra, 2014; Halt et al., 2014; Haselhuhn et al., 2012a,b, 2013a,b; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). Of the 53.2 million metric tons produced, roughly 8 million metric tons of hematite (Fe2O3) concentrate were produced using a process known as selective flocculation and dispersion (Cliffs Natural Resources, 2011). This process is the only economically viable method for concentrating low grade (< 40% Fe) fine grain (< 25µm liberation size) hematite ores. It is scarcely used due to difficulty in controlling the surface chemistry of the ore and high reagent costs (Department of Energy, 2001; Haselhuhn et al., 2013a). The process is highly dependent upon both reagent selection and precise control of the water chemistry during separation. This study shows the dependence of the process performance of a pilot-scale deslime thickener on the water chemistry in the feed slurry."

Jan 1, 2015

By R. J. Snow, S. N. Bhattacharya, D. D. Patil

Electrokinetics involves the movement of charged particles or water molecules in an applied dc field. Applications in particle fluid systems include the dewatering of soils, the densification of mill tailings and the treatment of coal wastes. In this paper, a novel application of this technique is discussed, wherein an electric field is applied to a coal-water slurry flowing through a pipe, resulting in lower pressure losses in the system. A unique experimental setup was designed and built to study the effect of an electric field (dc) on the wall shear stress for the flow of coal-water slurry through the pipe. The effect of solids concentration, current strength and pH on drag reduction across the system was quantified.

Jan 1, 2002

By Wei Victor Liu, Omer Faruk Ugurlu, Chengkai Fan, Bei Jiang

Accurate prediction of truck productivity plays a pivotal role in improving the efficiency and profitability of openpit mining operations. This paper proposes a deep neural network (DNN) model to overcome the challenge of predicting truck productivity in openpit mines. The prediction model was built using eight variables and was optimized by considering different train-test split ratios, numbers of hidden layers and neurons, and activation functions. The proposed model’s performance was evaluated using various metrics and compared with other commonly used machine learning algorithms. The results showed that the proposed model outperformed traditional machine learning models by achieving higher prediction accuracy. Moreover, a single-variable sensitivity analysis showed that haul distance is the most influential variable for predicting truck productivity. This study marks a pioneering effort in employing DNN to predict truck productivity in openpit mining, signifying a notable advancement in the field.

Jul 1, 2024

By R. F. Holub, P. J. Dallimore

Basic to solving the problem of the role of radon transport on radon concentrations in mines is to establish whether it occurs primarily as diffusion and forced flow through porous rock or through fissures in the rock. The laboratory experiments performed involved measurements of diffusion and emanation coefficients, porosity and permeability of representative rock samples. Significant differences have been found when comparing the results of the laboratory permeability determinations to those of the mine determinations. Considerations of underlying principles, however, suggest that the diffusion and emanation coefficients are the same in laboratory and mine. It was also found that moisture content plays a dominant role in radon transport through rock. Using these concepts and findings, some conclusions about the radon concentrations in mines have been drawn.

Jan 1, 1981

By E. L. McHugh

Digital camera and computer technologies can be used to monitor mine slopes and provide real-time warning of rock falls. NIOSH researchers assembled a surveillance system using low-cost video cameras and computer software from the security industry to test its effectiveness. The system is designed to signal an alarm when motion is detected and to record images of the scene. Masking can restrict motion detection to specific areas within the camera view; sensitivity is adjustable. The time-stamped images provide a record that can help reconstruct and quantify an event. Video motion detection can augment standard monitoring methods to increase safety in surface mines.

Jan 1, 2004

By Duk-Won Park

A new gage for monitoring fractures in underground openings was successfully developed utilizing the reflection photo-elastic technique. The gage may be used to detect crack initiation in mine openings or tunnels so that remedial action may be taken to prevent further deterioration. Fringes concentrated around the cracks were spread by the use of rubber backing. Crack growth as little as 0.003 inch up to as much as 0.1 inch width were detected in this study. Variation of gage materials will provide alternative ranges. The feasibility of the method was tested and calibration was made in the laboratory study. Field study successfully demonstrated the capability of applications in detecting mine roof crack development.

Jan 1, 1982

By J. M. Mutmansky, Aiping Wang

This paper outlines the patterns of methane emission in both longwall and room-and-pillar operations and discusses the effects that these patterns have on the decision as to whether the methane is most economically handled by ventilation alone or by means of a methane-drainage system in addition to ventilation. The costs of handling the methane in the ventilation system and the costs of implementing the methane-drainage system are discussed, as well as the costs related to the production of coal. The important issues of production slowdowns and gasouts are also discussed, as well as the proper response of mine management to such a situation. Suggestions concerning the keeping of production records related to methane problems are made, and the justification for more intensive economic analysis of coalbed methane extraction and utilization is discussed

Jan 1, 2000

By Wolfgang R. Wawersik, Charles M. Stone

INTRODUCTION Hydraulic fracturing was applied in horizontal drill- holes in the Salado salt formation near Carlsbad, New Mexico. Tests were performed approximately 650 m be- low surface to validate the design of a Waste Isolation Pilot Plant (WIPP) for the disposal of radioactive waste from defense activities of the United States. Hydraulic fracturing was performed primarily to determine whether the virgin in situ stress state at the WIPP site is isotropic and whether the magnitude of the virgin in situ stresses corresponds to the weight of the overburden. Beyond these limited objectives, however, measurements are now being reviewed to evaluate the usefulness of hydraulic fracturing in salt formations in general. Such measurements are desirable to determine stresses induced by mining and to monitor time-dependent stress changes around underground excavations in salt masses. Hydraulic fracturing was chosen because it is the only technique that can be readily applied in virgin ground far from existing mine openings. The method also appeared to yield directly the magnitude of the least compressive principal stress, regardless of the mechanical properties of the rock mass. A knowledge of the least principal compression was deemed sufficient to establish the isotropic character of the virgin in situ stress field under two conditions: (1) the Salado formation was mechanically isotropic, i.e., the fracture toughness did not vary normal and parallel to bedding so as to permit preferred fracture paths, and (2) pressure measurements were combined with determinations of the orientations of hydraulic fractures and, more generally, with observations of the characteristic hydraulic fracture patterns. The latter was possible by locating the drillholes for hydraulic fracturing along the axes of drifts that were mined several months later. The success of general stress measurements by hy- draulic fracturing of salt subjected to anisotropic stress conditions was and remains less certain. While the smallest in situ compressive stresses should still be equal to instantaneous shut-in pressures, there may not exist any unique relationships between the greatest and intermediate in situ principal stresses on one hand and the primary breakdown and fracture reopening pressures on the other. This problem would be a consequence of stress relaxation due to salt creep around any drillhole in which hydraulic fracturing tests are conducted. Moreover, lab- oratory measurements suggest that creep and stress relaxation could be so rapid that it might not be possible to interpret the measurements for anisotropic stress conditions even if hydraulic fracturing were performed as soon after drilling as possible. The primary objectives of the stress measurements in the WIPP were met by combining hydraulic fracturing tests with finite element analyses of the effects of salt creep, observations of hydraulically induced fracture pat- terns, and laboratory hydraulic fracturing tests on oriented core. In situ hydraulic fracturing tests in long drillholes were preceded by several trial tests to establish the best test methods and to demonstrate that salt could be fractured. The resolution of anisotropic stresses and special problems, e.g., in the identification of instantaneous shut-in pressures, are currently being addressed in hydraulic fracturing tests in a mine pillar, in tests following different delays between drilling and fracturing, and in tests with different frac fluids. This paper will review the main results of the analyses above and of one group of hydraulic fracturing tests at different distances from existing excavations. The paper will conclude with a brief description of the geometry of the hydraulically induced fracture patterns. Because of space limitations, it will be assumed that the reader is familiar with hydraulic fracturing or will first consult other sources (e.g., Cleary, 1980; Gronseth and Detournay, 1979; Zoback and Haimson, 1983; Nemat-Nasser et al., 1983; Kim et al., 1984)

Jan 1, 1986

By Lynn B. Hales, Randy A. Ynchausti

Object-oriented technologies have been developed to more closely model the way we think about the world and our natural approach to solving problems. Higher levels of abstraction, generalization and classification are benefits of an object-oriented approach. Object-oriented programming, design, and expert systems are part of this technology which is shaping the future of real-time supervisory control. Goals of real-time supervisory control systems include: minimizing variations in process operations, improving efficiency, maximizing production, and implementing procedures for starting and stopping the process. Incorporating object-oriented technology in design, development and implementation of real-time supervisory control systems provides new opportunities for these tasks. This paper discusses some of the opportunities and challenges of implementing real- time supervisory control using an object-oriented expert system for a rougher flotation circuit

Jan 1, 1993

By J. Liniecki, w. Chruscielewski, T. Domanski

INTRODUCTION Mining is the Polish greatest industry employing about 350 thousand miners in more than a hundred underground mines. The mining regions are located mainly in the south of the country - see Fig. 1. [ ] The coal mining dominates, however, and the zinc-lead and copper-ore mines presently employ about 16000 miners. All these mines are rather deep and wet. Their drawing shafts are between a hundred to more then thousand meters deep. The cross-adit of working area of mines ranges from several kilometers to a few tens of kilometers. The numbers of mines per mine differ also considerably and depend on the territory and type of mines. The largest coal mines employ about ten thousand miners but the largest metal ore mines do not employ more than four thousand miners. In all the mines the electric motors or diesel engines are being used. The intensity of mine ventilation, characterized by the volume of fresh air injected in to the main ventilating shaft per miner and per unit of the power consumed by the engines is about 6 cubic meters per minute per man and per horsepower. The studies of the potential alpha energy of radon daughter products /RnDP/ could be divided into the three developmental stages: I-st - stage /1966-1970/ the stage of so called Pilot Survey. During this stage concentration of potential alpha energy of RnDP in the air was measured in selected typical mines in all mining regions of the country. II-nd - stage /1972-1974/ was the periodical control of concentration of potential alpha energy of RnDP in the air of zinc-lead and copper-ore mines which have been chosen and recognized during the first stage as being the most hazardous ones. Air-sampling system /ASS/ measurements were applied during this stage.

Jan 1, 1981

By B. K. Kejriwal, A. K. Ghose

Under specific geological environment, the full extraction of a coal seam is not possible either because of its extraordinary thickness or the presence of surface structures and bodies of water or because of the conditions prevailing in upper seams. Not uncommonly, therefore, for working such seams, pillars of coal are left for the permanent support of the overburden, and voids around the pillars are filled with sand to strengthen the pillars and prevent their deterioration with time. However, the paucity of river sand has focussed attention on the need for alternate strategies including trials with partial filling of the voids. This study has sought to examine in the laboratory the effects of partial and complete filling on the ultimate load bearing capacity and post-failure behaviour of small, tall pillars using artificial material.

Jan 1, 1986

By J. D. Miller

"Bastnaesite is one of the important mineral resources for the production of rare earth materials, and it is typically associated with calcite and quartz as gangue minerals. Fatty acid or hydroxamic acid are recommended collectors for bastnaesite flotation. In this research, potassium lauryl phosphate was expected to provide a stronger flotation response for bastnaesite than for the calcite and quartz gangue minerals. Using potassium lauryl phosphate as collector, the results of captive bubble contact angle measurements, zeta potential determinations and microflotation experiments for bastnaesite, calcite and quartz are reported. Greater selectivity for bastnaesite was achieved using potassium lauryl phosphate than using octyl hydroxamate as collector. These results indicate that potassium lauryl phosphate might be a promising collector in the flotation of bastnaesite ores. The computation results of universal force field (UFF) interaction energies for the mineral-reagent interactions are also reported and were found to correlate well with the experimental microflotation results.IntroductionBastnaesite ((Ce,La)FCO3) belongs to the mineral class of semisoluble salt minerals, whose characteristics include ionic bonding and limited solubility in water. Bastnaesite, for the most part, contains the cerium subgroup or the lighter rare earth elements (Zhou et al., 2014). The Mountain Pass deposit in California in the United States and the Bayan Obo deposit in Mongolia in China are the two major deposits of bastnaesite (Azizi et al., 2016; Satur et al., 2016). Calcite and/ or quartz are common gangue minerals in these and many other rare earth deposits (Jordens et al., 2014)"

Jan 1, 2017

By Z. Yunquan

The flocculation and dispersion behaviors of microsize wolframite and quartz are systematically studied in this paper. For synthetic mixtures, the floc separatory method on gravity units--electromagnetic vibration table (EVT) and lifting column (LC), have been approached. Satisfactory results can be obtained with a weak shearing. A better metallurgical performance can also be achieved for natural ore slimes through the combined technique. The efficiency is better than that of single gravity separation. Finally, the mechanism has been investigated.

Jan 1, 1990

By I. Shah, L. G. Austin

A method for quantitative investigation of the phenomena involved in fine grinding of materials that follows the changes in the breakage rates of fine particles has been presented. For relatively hard, brittle, non-coating material like quartz, the slowing down effect of breakage rates starts to be significant at relatively coarse sizes, which goes often undetected in closed circuit grinding systems, producing relatively coarse product, say P80=75µm However, for fine grinding systems, as the -10µm fractions begin to build-up, and classification becomes more difficult, the build-up of fine sizes causes a slowing down effect Compounding this problem is the difficulty of obtaining accurate cumulative weight size distributions in the fine size region.

Jan 1, 1983

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978

By Howard L. Hartman

In 1969, the OECD conducted a survey internationally to determine the status and needs for research and development in the field of tunneling. The findings also have some validity for underground excavation in general and for underground mining per se. Of the 17 countries responding to the survey, the U.S. leads in the level of support: $21.8 million and 720 man-years of effort over the last ten-year period. The total volume of R/D for the 17 countries was estimated to be $86 million and 5800 man-years. Performance of research was primarily by government agencies and public utilities (70%); the balance was conducted by private organizations and universities (15% each). In the categories of R/D subjects surveyed, three--Wk mechanics, soil mechanics, and geological exploration--outstripped all the rest in priority of effort to date. Ground support, equipment development, excavation, and environmental control received intermediate attention. The subject areas in which the least R/D effort has been expended are materials handling and systems evaluation. For the future, those R/D areas rated the most crucial to achieve technological progress in tunneling were excavation, ground support, and materials handling. The survey findings of tunneling activity indicated (1) a disturbingly low level of R/D activity in the private sector, (2) the necessity for a reordering of priorities in directing research efforts in the future, and (3) a lack of recognition to date of the importance of systems evaluation in R/D activities.

Jan 1, 1970

By R. Patterson

Tracer gas sampling methods are useful for monitoring ventilation systems, especially in remote or inaccessible areas, and can be utilized for analysis of the ventilation system immediately following a mine emergency. However, the success of this technique is largely dependent on the accuracy of release and sampling methods. Analysis of sampling methods is crucial for rapid response and dependable results during emergencies. For the purpose of this study, four well-accepted sampling techniques currently used in the mining industry were compared using solid-phase microextraction (SPMe) fibers with sulfur hexafluoride (SF6), an industry standard, as the tracer gas. Current sample collection techniques include plastic syringes, glass syringes, Tedlar bags and vacutainers. SPMe fibers are used in a variety of industries, from forensics to environmental sampling, and are a solventless method of sampling analytes. To analyze these sampling methods, samples were taken from a 0.01 % standard mixture of SF6 and nitrogen and analyzed using electron capture gas chromatography. A relative standard error of less than 10% validated results to compare the accuracy of various methods. The technical and practical issues surrounding each sampling method were also observed and discussed.

Jan 1, 2011