Search Documents

By D. Lelinski

Air-sparged hydrocyclone (ASH) flotation is one of the new promising technologies. Numerous applications have been successfully tested since its conception; nevertheless, research and development efforts have continued to provide for further improvements with respect to operating conditions and design considerations. Results from experimental studies on bubbles generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation have been determined using a high-speed photographic technique. The influence of many factors including surfactant concentration, water flowrate, and porous tube pore size has been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flowrate (shear field) the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions the average bubble size was found to range from about 100 to 300 microns in diameter.

Jan 1, 1995

By S. L. Bessinger

In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross-section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Headlosses in mine entries are calculated using Atkinson's Equation (1). [H = (English) H = (SI) (1)] where H = pressure ,loss, in. of H20 (Pa) K = friction factor, lbf min2/ft"4(Kg/m3) P = perimeter, ft. (m) L = airway length, ft (m) Q = airflow quantity, ft3/min (m3/sec) A = flow cross sectional area, ft2 (m2)

Jan 1, 1987

By B. R. Waples

Sometimes a project is born easy, sometimes a project has a hard time being born. Probably every project can say we had tremendous problems to overcome and they would all be right. This project had all things happen to it. Born easy, a hard time after being born, there were tremendous problems to overcome but here it is, a major copper project, a major operation, and a new source of copper for Mexico and the world market. La caridad is an ore body located in the state of Sonora in northwestern Mexico. It is at an elevation of 1,200 meters above sea level and the nearest major city is Hermosillo, the capital city of Sonora. Hermosillo is located approximately 270 kms (about 168 miles) to the southwest of la caridad. North of la caridad, 130 kms (about 81 miles), is the U.S. border town of Douglas, Arizona, which has a sister city on the Mexican side of the border -Agua Prieta.

Jan 1, 1979

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI's Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By G. E. Maryniak

To date, human space exploration has been almost completely dependent on the use of resources carried with astronauts and cosmonauts from the surface of the Earth. The only exception to this has been the harvesting of solar energy to power space stations like Skylab, Salyut and Mir for long-duration missions. This dependence on materials which must be transported into orbit at costs in excess of $5000 per pound is the fundamental limiting factor in space exploration and operations. It is likely that launch costs can eventually be greatly reduced by means of such innovations as true single stage to orbit vehicles, aerospace planes, or serial electromagnetic or laser launch systems. However, the Earth will always remain an expensive source of materials for space construction and for basic commodities such as propellant and life support liquids and gasses. Fortunately, abundant sources of materials exist which are already in space, outside of the Earth's deep gravity well.

Jan 1, 1992

By Fathi Habashi

THE CHOICE of a precipitant for a certain metal ion depends, beside the economic factor. on the following factors: 1) The precipitant should be specific as far as possible so that pure precipitates can be obtained

Jan 1, 1970

By W. C. Meyer

The concept of using powdered coal-in-oil-mixtures (COM) as a composite fuel to conserve oil resources and relieve import supply problems is being vigorously promoted by the Department of Energy via the sponsoring of various demonstration units (1). The idea of COM as a useful alternative fuel has been explored on and off for over 100 years (2). The approach must be capable of grinding, mixing, storing, and combusting COM with presumably only minor equipment changes on oil-fired boilers. DOE estimates that 56 000 m3 of oil (350 000 barrels) could be spared daily if a 50-50 COM was used to generate electricity. Of course, the ability of COM suppliers to prepare and deliver a stable suspension of COM at reasonable economic costs must be achieved if the concept is to be successful. This report reviews the various methods used to attain stable coal-oil mixtures. Various physical-chemical principles associated with each method of stabilization are also discussed.

Jan 1, 1981

By Muhammad Azeem Raza, Samuel Frimpong

Underground mining environments are inherently hazardous and can lead to emergencies where effective rescue and self-escape become critical. Missouri University of Science and Technology is pioneering new technologies for effective self-escape. The rescuers and miners need to be trained in these new technologically driven environments. Previous research in fields like aviation, medical surgery, and oil and gas drilling has demonstrated the effectiveness of virtual simulation training, but the mining sector has yet to fully adopt advanced tools such as eye-tracking and immersive training modules. This research proposes a comprehensive training infrastructure incorporating these technologies to enhance situational awareness and decision-making during emergencies. The novelty lies in the application of advanced miner escape and communication technologies, specifically designed to monitor and enhance cognitive responses in high-stress situations. By leveraging these technologies, the proposed training infrastructure aims to prepare the next generation of underground miners and operators, by equipping them with the necessary skills to manage emergencies effectively.

Feb 1, 2025

By L. E. Eary

Many of the major international gold mining companies provide data on rates of greenhouse gas (GHG) emissions as part of their environmental reporting commitments. These data are evaluated by an index defined as the annual GHG emission rate in metric tons, divided by the annual amount of gold produced in grams, and referred to as GHGgold. This paper examines ranges of GHGgold values for a cross section of gold mines as a function of mining method (openpit, underground and combined operation) and ore-processing method (mill, heap leach and combined methods) for reported ranges of operational data, including annual total tons mined, ore processed and gold grade. The evaluation shows that ranges and distributions of rates of GHG emission are approximately similar across different mining methods and ore-processing methods. The data presented in this paper provide the context needed to make comparisons of GHG emissions reported in companies’ annual reports to the ranges reported for the overall gold mining industry.

Jan 1, 2009

By Roger Bell

Most modern mines can profit from improvements in information handling. Recording systems in many cases were designed to satisfy certain necessary legal requirements, but not specifically to provide management information. As a consequence, the top managements of these properties work with cost data and production information that is dated, lacking in detail and clouded with supposition. It is the intent of this paper to describe an information system for a mine-plant complex in terms of the type of data, application areas and the existing equipment technology that may be applied to improve this situation. The economics of information processing and data handling will not be discussed in detail. This paper is based on the premise that information is something of value and that information processing like a manufacturing operation works for and is subject to management control. Information, the product, must be of quality, and the cost must be favorable in terms of its use.

Jan 1, 1965

By C. Cardoso, G. Bermudez, A. Jalili

Bigger flotation cells can result in larger froth surface areas and longer froth transport distances, this has been credited to impact froth recovery. Thanks to recent advancements, the newer flotation machines can be designed with different launder and crowder arrangements to enhance froth management. Nevertheless, lower head grades, complex ores and even larger mechanical flotation cells can lead to insufficient froth collection, even if the cell is equipped with the most recent flotation advancements like the center launder design. Aforementioned issue can become critical at the end of the flotation row. Increased crowding has been proven to be a solution to overcome inadequate froth recovery. However, scaling-up crowders for larger flotation cells can rise challenges, particularly in terms of structural limits and design for service. This paper presents the development journey for the Spider Crowder Upgrade, an advancement to improve froth collection in large flotation cells that are already equipped with center launders.

Feb 1, 2024

By L. L. Oriard

There are certain site-specific geological and physical features of a rock mass which control its behavior under the dynamic stresses induced by the action of explosives. It is essential that blasting technology be adapted specifically to those features. There does not exist a single, simple "right" way for each type of blasting operation, but rather each operation must be custom-designed for each site. When this is done, it is often possible to produce unusual but highly desirable end resglts, such as undisturbed narrow rock walls, monoliths and square benches. Although the techniques illustrated here were developed specifically for "sculpture blasting", the geomechanics principles would apply to other types of blasting control, both large-scale and small-scale. Because the techniques are designed more for the purpose of modifying the site responses which would ordinarily be expected than they are to developing new "blasting formulae?, the name "Modified Site Response Blasting" will be used.

Jan 1, 1984

By Robert L. Stroup

Let me open my remarks this morning by stating how we as legislators and as natives of the western coal-producing states feel about our role in becoming one of the major producers of coal-related energy and chemical products is similar to the groom at his shotgun wedding. We are apprehensive, to say the least, as to the ultimate outcome. We do not have complete freedom of choice. It will certainly change our quality of life. We are concerned about the increase in population, but are realistic enough to recognize that we are forced to go through with the marriage. Other alternatives could be worse than the bride. Also, we were aware that this could occur, but we did not plan on it being this sudden. Or, put another way, we have two groups advising us that our choices are cattle or coal, food or fuel, pollution and people or pure air, wheat or gas, clean water or prosperity, noise or solitude.

Jan 1, 1976

By Elif Emil-Kaya, Bernd Friedrich, Merve Papakci

Samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are used in the production of SmCo permanent magnets, which have excellent temperature stability, corrosion resistance and oxidation resistance. Of the two types of SmCo magnets, one contains a high amount of iron, approximately 15.2 percent. This paper focuses on the recycling of iron (Fe)-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Jul 1, 2024

By D. Seneviratne

Iron transfer from the pregnant leach solution (PLS) to the electrolyte can have a major economic impact on solvent extraction (SX) operations. High iron transfer will lead to greater operational costs, due to increased reagent consumption through electrolyte bleed and make up, or increased power costs due to decreased electrowinning current efficiency. Bioleaching of low-grade copper sulfide ore from the Kennecott Utah Copper Mine was investigated in a large scale piloting program including SX and electrowinning. Plant data and lab test work conducted throughout the course of operation, show that the unique containing PLS high ferric iron with high pH can lead to lower Cu: Fe selectivity than is typically seen in traditional copper SX operations. The impact of high ferric iron on the plant operation, and methods to reduce iron transfer will be discussed. Special considerations need to be taken for plant operating conditions and selection of SX reagents (including both extractant and aromatic content of diluent) based on the feed PLS characteristics.

Feb 23, 2014

By X. Cui, H. Ding, J. Wen, Q. Gu

This study is a continuation of previous work designed to further explore the mechanism of the bioleaching of sulfide concentrate at neutral pH by heterotrophic bacteria Bacillus megaterium QM B1551. The concentrate contained 13.2 percent nickel (Ni) and 0.2 percent cobalt (Co), which presented primarily as pentlandite and pyrrhotite. Contact and noncontact bioleaching experiments were conducted with finely ground ore at an initial pH of 6, resulting in 44.7 percent of Ni and 38.2 percent of Co leached in the contact-bioleaching treatment. Oxidation experiments of sulfur, thiosulfate (S2O32−) and ferrous ions (Fe2+) by cell membrane were performed to verify whether sulfur transferase, thiosulfate quinone reductase and enzyme cytochrome B558 on the surface of the bacteria could be expressed to oxidize the sulfide. The results show that thiosulfate quinone reductase and cytochrome B558 could be expressed to oxidize S2O32− and Fe2+ to SO42− and Fe3+, respectively.

By J. J. Zimmerman

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise data from 2000-2004 show that the continuous mining machine is first among all equipment with 35% of the noise overexposures. Joy Mining Machinery, in collaboration with the National Institute for Occupational Safety and Health (NIOSH), is conducting research to reduce noise generated by continuous mining machines. This paper describes a ?JOY Designed for Noise Reduction? (JOY-DNR; Patent Pending) tail section as a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 45% and 65% noise exposure reduction for the operator when compared to a standard machine. Utilizing this newly developed noise control, along with previously proven controls, will provide continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2010

By Mir Ahmad Mohammadi

Land uplift due to mine flooding has become a significant challenge with extensive historical mining activities, particularly in Germany’s Ruhr district. The cessation of coal mining operations has led to a gradual rise in groundwater levels, altering geotechnical and hydrological conditions and causing surface uplift. This study develops a system dynamics (SD) model to investigate the dynamic interactions of influential variables such as groundwater levels, total stress, porosity and permeability with land uplift over time. The model integrates causal loop diagrams (CLD) and stock flow diagrams (SFD) to comprehensively understand the system’s behavior. SFD illustrated that for a 10 percent increase in groundwater level, the land uplift increased by about +6 percent, and a rise of 200 percent in total stress caused an 18 percent increase in effective stress, which decreased the land uplift by about 20 percent. This study highlights the importance of dynamic modeling in informing land-use planning and mitigating the long-term impacts of land uplift after mine closures.

Mar 1, 2025

By Tim O’Neil

Tire companies have historically used the mining industry as a platform to launch new technologies. And the mining industry has been receptive to that. So, while developing its Two Piece Assembly, Goodyear noted a number of trends in the mining industry: •The global market sophistication of equipment and operations requires the packaging of products and services to provide the best return on investment. •Industry consolidation and growth have resulted in fewer, more powerful mining houses, leveraging purchasing power in the marketplace. •User productivity demands continue to drive original equipment manufacturers to develop higher pay-load equipment. •Technology needs include improved ergonomics, to reduce fatigue and increase operator productivity. •Increased laws and environmental regulation prohibit on-site whole tire disposal practices.

Jan 1, 2003

By Clyde L. Smith

Since the early 1950's exploration in the Yukon Territory, Canada, has been confined largely to Selwyn basin where at least five large stratiform or massive sulfide Pb-Zn deposits have been discovered. The five ore bodies total nearly 100 million tons of 10-16% combined Pb-Zn with 1-3 oz./ton Ag. The only deposit currently in production is the Anvil Mine operating at 8,000 tons per day. Beginning in 1972, exploration in the Mackenzie Mountains, east of Selwyn basin and west of Mackenzie arch, resulted in finds of Mississippi Valley type Zn-Pb mineralization in a belt of Proterozoic and Lower Paleozoic carbonate rocks (Figure 1). Four districts have been located and intensive exploration by numerous Canadian and Arnerican mining companies is currently in progress over a length of 400 miles in the carbonate belt. The consensus is that a major new Zn-Pb province may be taking shape.

Jan 1, 1974