Search Documents

By Brendan Parker, Joseph Skrypniuk

Boddington Gold Mine1 (BGM) commenced production in 1987 and is currently ranked as the second largest gold producer in Australia. In a strategy to improve plant efficiency, constraints to plant performance were identified and prioritised with a view to maximising benefit for minimal expenditure. After identifying that leach kinetics and circuit residence time were major constraints, the introduction of oxygen was identified as having the greatest potential for the delivery of sig­nificant cost benefits. The application of oxygen, initially by conventional tech­niques, and subsequently by installation of Atomaer's Filblast gas shear reactor, improved gold recovery, reduced the resi­dence time constraint and enabled higher mill throughput to be achieved. Additional benefits included operation at lower pulp densities and a reduction in reagent usage. A significant reduc­tion in unit operating cost resulted from these benefits. This paper quantifies the above benefits in a format accept­able to both metallurgists and accountants by integrating the findings in a techno-economic perspective.

Jan 1, 1996

By Mike Jahraus

The topic I would like to throw out for discussion this morning concerns the metallurgical solution management of operating a valley fill leach facility where ore depths approach 250 feet and deeper. We are currently beginning to experience solution transport times through our heaps on the order of 60 to 70 days as our heaps approach 250 feet. Incorporating a two-stage leach scenario, or solution enrichment, these times are nearly doubled. Concurrent with the increased solution transport times, the solution tenors being produced by our heaps are being diluted slightly as percolation occurs through the lower lifts. I feel the best way to handle these situations is to closely monitor solution application rates, and carefully manage ore stacking. Also, as heaps become deeper, metallurgical and hydrologic characteristics of the ore become inter-related, i.e. if channeling or preferential flow is taking place, lowering cross-sectional flow rates to older leach panels with help re­institute capillary flow while helping to prevent solution tenor dilution.

Jan 1, 1999

By P. Whincup, T. Showell, B. Marchant, R. Dunne

An oversupply of copper on world markets in the early 90' s, coupled with a decrease in demand, resulted in a "tight" market for the sale of copper concentrate. In these conditions small producers of low grade copper concentrates found it difficult to sell their products. The situation was exacerbated for those producers also having reasonable quantities of penalty elements (e.g. As, Bi). The Telfer Gold Mine bulk copper gold concentrate, produced from treating underground sulphide ore, fell into this category (i.e. 16% to 20% copper, 30% to 35% sulphur and 3500ppm to 4500ppm arsenic). The concentrate sulphide minerals are predominately chalcocite and pyrite. Although a higher grade copper concentrate was attainable a substantial decrease in gold recovery ensued. Under the prevailing market conditions a decision was made to stockpile concentrates pending either an easing of market conditions or alternatively finding an on site method for treating the concentrate to recover both the contained gold and copper.

Jan 1, 1995

By D. Triantis

This paper presents the results of laboratory experiments for the detection of electric signals from Fiber Reinforced Polymer (FRP) sheet samples which have undergone a temporally increasing loading of bending type up to fracture. Electric signals that were recorded while the sample was subjected to bending are referred from now on as Bending Stimulated Currents (BSC), in order to differentiate them from the relevant signals emitted by materials that suffer uniaxial compressional stress. The latter signals are referenced as Pressure Stimulated Currents (PSC). BSC emitted from FRP sheet samples presented here, were recorded after applying three successive load steps to samples. The increase rate of applied stress was about 0.15kN/s. Initially starting from low load values to higher load values until the FRP sheet reaches at a state just before its failure. The BSC records from FRP samples are compared to equivalent recordings from cement mortar beam and distinguishable differences are discussed.

Jan 1, 2006

By Charles S. Phillips

Kaiser Aluminum and Chemical Corp. (KACC) had been discharging spent bauxite-generally referred to as red mud-into the Mississippi River for almost 20 years when, in 1972, it agreed to store the waste solids on land. KACC decided to utilize a DREW system (decantation, drainage, and evaporation of water) where the spent bauxite is deposited in a large drying bed, surrounded by a 9-m-high levee. At the bottom of the bed, corrugated, perforated plastic pipe is encased in filter sand. The company built one DREW bed at Gramercy, LA, in 1973 and a second at Baton Rouge in 1974 using draglines, tractors, and rubber-tired scrapers. When a third bed was needed in 1977, the estimated construction cost using draglines was judged too high and KACC personnel began searching for a better, less expensive method for constructing the levee. A bucket-wheel excavator and conveyor system was selected and has proved to be less costly than more traditional earth-moving systems.

Jan 7, 1980

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By J. Gathje

Normal process development for pressure-preoxidation treatment of refractory gold ores starts with laboratory batch autoclave tests. That is followed by continuous autoclave pilot-plant testing to confirm the process options. This scheme will generally provide good information showing the effects of grind size, time and temperature. And it will indicate whether autoclave preoxidation will produce solids that are amenable to cyanidation for gold recovery. However, several test programs have shown that the cyanide-leaching responses of treated solids from the batch tests can differ considerably from those achieved by the continuous pilot-plant autoclave. It has become apparent that laboratory investigations should extended to include the use of a semicontinuous autoclave test procedure. Santa Fe Pacific Gold conducted several months of metallurgical investigations for a major refractory sulfide gold deposit. The project started with batch tests to investigate and optimize the primary variables, such as grind size, retention time and temperature. These tests were conducted using a representative whole ore composite.

Jan 1, 1995

By Mark E. Smith

Large scale copper heap leaching in Chile began in November 1980 when the Lo Aguirre heap leach project was put into operation. At almost the same time, El Indio gold mine began production. While El Indio was not a heap leach project, it was Chile's first major bulk tonnage, open-pit gold deposit. This paved the way for the introduction of North American gold heap leach technology in the early 1980s. Heap leaching has become more popular in Chile during the past five years because it allows the exploitation of large but relatively low grade ore bodies at a reasonable cost. Pioneering research in hydrometallurgy carried out at some Chilean universities and at the Centro de Investigaciones Minero Metalurgicas (CIMM) played an important role. There are more than 10 large copper heap leach and solvent extraction/ electrowinning (SX/EW) process plants in different stages of development in Chile. Total production from these facilities will eventually increase Chile's present copper exports about 50%.

Jan 1, 1995

By P. Pal Roy, Ajit Raj Ostwal, M. M. Singh

Field investigations have revealed that sawdust can be used as an efficient additive to ANFO for carrying out production blasts in limestone mines. Sawdust can be used at a reasonably reduced cost without sacrificing fragmentation, muck profile and wall control. Such additives lower the detonation pressure of ANFO by acting as low-grade fuel that reacts or burns more slowly in the presence of ammonium nitrate than does fuel oil. On detonation, it eventually forms near-ideal oxygen balance that helps in liberating maximum energy to break the surrounding rock. It also forms a low-density stable mixture that helps in reducing loading density (kg/m) of explosive in the blasthole. Experiments performed at the Hirmi Limestone mine, M/s L&T, and at the Lambasta Limestone mine, M/s Jaypee Rewa Cements, showed the novel acceptance of the technique in a highly competitive market where cost reduction has been a major area of thrust.

Jan 1, 2003

By Jorge Rubio, Luis Valderrama, Carlos Pérez

This work describes the effect of the degree of energy transferred to the pulp, during the conditioning stage, on gold flotation fines recovery, grade and kinetics, with three types of frother (Dowfroth 250, pine oil and MIBC) and amyl xanthate as collector. Best results show an increase in 24% recovery and 50% in concentrate grade, depending on the intensity of conditioning and type of frother (better with Dowfroth 250). For low or intermediate energies (0.5-1.5 kWhlm3 pulp), the fine particles adhere to larger ones, increasing the recovery due to a mixture of carrier (pyrite, in this case) and autogeneous carrier flotation and at higher shear (2-3 kWhlm3 pulp), gold fine particles aggregate themselves. These phenomena are demonstrated by measurements of flotation rate, true flotation (flotation by actual particle-bubble adhesion), and by the amount of entrained particles. Alternatives for this type of pulp conditioning and mechanisms involved are discussed.

Jan 1, 1995

By Justus B. Deen

Given that the majority of mine ventilation operating costs are imposed by shafts, the need to predict the resistance of a planned shaft with reasonable accuracy is important. During conceptual design, shaft resistances are usually predicted by use of published friction factors, k, based upon lining and fitting configurations. More often than not, published friction factors do not directly coincide with "real" shafts, so their use is somewhat limited. For more accurate shaft resistance determination, equations both theoretical and empirical may be employed if there is detailed knowledge of the shaft. These equations treat the shaft resistance as discrete components, with their sum being the overall shaft resistance. This paper describes the basic shaft resistance equations and verifies these equations by comparison to field measured shaft resistances. Several shafts were examined which varied in depth, shape and fitting arrangements. Results are presented and conclusions drawn to show that the shaft resistance equations are accurate.

Jan 1, 1991

By J. B. Pautler, A. E. Gross, M. G. Strominger

The U.S. Bureau of Mines research on the use of cement as an agglomeration aid allowed precious metals heap leaching to become an economically viable method of precious metal recovery during the 1980's. However, many agglomerated ore bodies still exhibited poor heap/agglomerate strength. Precious metal recovery was often too slow or required prohibitively high levels of cement to be economically sound. Problems with heap ponding, blinding, and solution channeling and "wash-out" indicated that there was a need within the industry to improve on existing agglomeration technology. An in-depth research effort was undertaken to satisfy this need. Three years of research led to a patent on the use of vinyl addition polymers as effective agglomeration aids. A close working relationship between Brewer Gold and Nalco Chemical Company aided in the development of this program. This paper details the pilot test work, the full-scale evaluation at Brewer Gold Company, and conclusions.

Jan 1, 1990

By R. Hogg, T. F. Dumm

A simple shape description scheme has been developed which has the specific aim of distinguishing between angular and more rounded particles. The procedure involves fitting a general polygon (usually about 20 sided) to the particle profile. Geometric shape descriptors have been defined based on variations in the angles between adjacent sides and their radial displacement from the particle centroid. A two-parameter shape description, incorporating an angular variabli1ity and an elongation index, has been shown to be clearly consistent with visual observations. A single-parameter angularity index has been shown to be very sensitive to small differences in particle roundness and seems to provide a better description of angularity than other approaches such as signature and fractal analyses. The scheme has been applied to three sets of fine quartz particles produced by different grinding procedures. The results indicate that the technique is capable of distinguishing between angular and re1atively rounded particles and can quantify their specific shape features.

Jan 1, 1991

By James L. Crowe

Electric-power-generating plants fired by fossil fuels are faced with increasingly stringent requirements for control of sulfur emissions. Several approaches for limiting these emissions, or for operating such facilities in an environmentally acceptable manner, are being pursued. Some of the approaches are based on the use of naturally occurring carbonate rocks or of materials derived from them. This paper discusses primarily the carbonate-rock-based processes being developed for control of sulfur dioxide emissions from fossil-fueled electric-power-generating plants. It includes a discussion of the role of carbonate rock materials in removal of sulfur dioxide from stack gases after combustion, capture of gaseous SO2 during the combustion process, and removal of sulfur from fuel prior to complete combustion. Materials derived from carbon- ate rocks are generally used in processes which convert the sulfur to a throwaway product, but there are also proposed processes in which the sulfur is converted to a useful product and the absorbent is regenerated for reuse.

Jan 1, 1974

As mentioned in chapter 8, one of the objectives of the budget is to provide a mechanism for ongoing measurement and control of the production operation. The budget shows expected performance. Actual results are compared to this benchmark to evaluate past performance and to direct future activities. The variances between budgeted and actual results identify specific activities that did not perform as expected (whether negatively or positively). Managers who use variance analysis are essentially applying a management- by-exception philosophy. Individual organizations will determine variances that reflect their own processes and managerial interests, but these variances all follow the approach outlined here. Firms will also vary in the extent to which variances are reported. Some firms use a few variance measures for the overall production organization whereas others calculate variances for individual departments or even individual work areas. As mentioned in chapter 5, it is important to distinguish between controllable and noncontrollable costs when using budgets for control and evaluation.

Jan 1, 1999

By John A. Ames

Limestone for portland cement must be beneficiated to produce uniform raw material for the kiln. Careful quarrying and selective recovery are factors in this process, but the chief aspects of beneficiation are "in plant" processes, such as crushing and screening, washing, grinding, flotation, and heavy-media separation. Numerous technical and economic problems exist. Detailed studies of the limestone deposit and the stone itself are required for intelligent beneficiation. As used in this paper, beneficiation is defined as the improving of limestone composition so as to produce an economically usable raw material A limestone deposit is defined as a mass of limestone which can be recovered, by quarrying or mining, for sale or for use in a commercially profitable operation. The stone may require elaborate processing, or it may qualify with little or none. Obviously, the "commercially profitable" qualification may change as the economy changes. Potentially commercial deposits may be of much better quality than actually developed deposits, and yet may be denied development for various economic reasons.

Jan 1, 1966

By V. McLemore

New Mexico ranks 2nd in uranium reserves in the U. S., which amounts to 15 million tons ore at 0.277% U3O8 (84 million lbs U3O8) at $30/lb (EIA, 2006). The most important deposit in the state is sandstone within the Morrison Formation (Jurassic) in the Grants district. More than 340 million pounds of U3O8 have been produced from these deposits from 1948-2002, accounting for 97% of the total production in New Mexico and more than 30% of the total production in the United States. Sandstone uranium deposits are defined as epigenetic concentrations of uranium in fluvial, lacustrine, and deltaic sandstones. Three types of sandstone uranium deposits are recognized: tabular (primary, trend, blanket, black-band), roll-front (redistributed, post-fault, secondary), and fault-related (redistributed, stack, post-fault). Several companies are planning to mine these deposits by in-situ leaching.

Jan 1, 2007

By Tomb. T. F., R. A. Haney

During the past several years, the Mine Safety and Health Administration (MSHA) has conducted studies in underground mining operations to obtain information on occupational exposures to diesel particulate (DP), mine environmental DP levels and on the effectiveness of methodologies used to control DP. The studies conducted were representative of four coal mines and 10 metal mines. The metal mines included two lead-zinc mines, one limestone mine, two potash mines, one zinc mine and four salt mines. Three of the four coal mines were using disposable diesel exhaust filters to remove particulate from the exhaust and one was using a reusable wire mesh filter. Results of these studies indicate that average DP levels in coal mines not using exhaust filters range from 0.9 to 2.1 mg/m3, The use of exhaust filtration devices reduced these levels by about 50% to 90%. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1996

By Brian W. Hester

All gold occurrences in Tanzania are of Precambrian age and in geological settings similar to gold deposits in other parts the world. The three main areas of interest are perhaps the least prospected of areas of gold mineralization in Precambrian rocks in non- aligned, or market economy nations. Historic production exceeds 77.660 kg (2.5 million oz). Current results by small scale workers go unreported, but have been estimated to be as high as 11.000 kg (350.000 oz) annually. Gold occurs in both lower and upper Precambrian rocks. In the older. gold is associated with greenstones and iron formations typical of many cratonic areas of Precambrian age. The Tanzanian Craton lies in the north west quarter of the country where it is flanked on both east and west sides by mobile belts involving upper Precambrian rocks of high metamorphic grade. Gold occurs in fractures in the western belt within two distinct areas.

Jan 1, 1989