Search Documents

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, 150 km southwest of Ciudad Juarez. The ore deposit was discovered in 1979, and was placed in production in 1992. The production rate is about 2400 tpd from an ore reserve of 8.5M tonnes. Grades average about 8 % Zn, 0.5 % Pb, 0.2 % Cu and 50 g Ag per tonne. Substantial inflows of water into the under-ground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark was operated through a joint venture, Minera Bismark, S.A. de C.V., with U.S. and Mexican partners, but since early 1993, it is wholly Mexican-owned and operated.

Jan 1, 1994

By Y. Luo

In designing and operating underground room-and-pillar coal mines, it is always difficult to achieve a good balance between preventing surface subsidence and achieving high recovery ratio. In this paper, a design methodology applying the pressure arch theory is proposed, and the principles and mathematical models involved are detailed. A computer program was developed to carry out the design optimization process and was applied to the examination of a documented case in which a massive cascading pillar failure had occurred over a large area in a shallow coal mine. The results indicate that the proposed design method can be applied to prevent subsidence while achieving reasonably high recovery ratio for roomand- pillar mining operations.

Jan 1, 2014

By Donald B. Buddecke

The large walking dragline has been the most commonly used overburden-stripping equipment in Texas lignite mines. These draglines, operating on the highwall side of the pit, can excavate to a depth of 45 m. Considerable overburden rehandling is required beyond 30 m and may reach 100 percent by 45m. As pit depth increases, dragline operation also becomes more complex, with two or three passes being necessary to make a cut 30 to 40 m wide. Multiseam operations also require extra passes. At pit depths greater than 45 m, the dragline must be operated also from a spoil bench. This can be difficult in the unstable alluvial deposits in which lignite occurs.

Jan 1, 1985

The criteria used to design, operate and control flotation columns are significantly different from those used for conventional flotation machines. Therefore, a computer-aided design (CAD) package for column flotation has been developed. The simulator has been set up using guidelines developed at Virginia Tech and information published in literature during the past few years. The simulator is useful for determining the proper design and appropriate operating conditions for a column cell to fit a specific set of conditions. In addition, the simulator can be used for training in column operation and for trouble-shooting operational problems. Simulation results have been found to be in good agreement with experimental data obtained using laboratory columns.

Jan 1, 1990

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the important parameters influencing gold recovery. The model was used to direct modifications to plant operating practice. The cyanide-dosing strategy was changed to reduce gold losses from preg-robbing and to cut reagent consumption. A finer grind was achieved without capital investment. The density in the carbon-in-leach circuit was lowered, and tighter control was exercised over the plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz ($9.64/g) gold, and concomitant reagent cost savings of $55,000/ month.

Jan 1, 2000

By Charles Stone, Eric Wang

A method for estimating geotechnical rock loads for shallow cut and cover subway stations is presented. Localized geotechnical conditions lead to extreme variations in rock loading on the walls of subway structures. Actual lateral rock stress on these structures can range from near zero to over four times the vertical in-situ rock stress. The primary factors affecting the actual lateral stress are intact and rock mass mechanical properties, excavation sequence, localized tectonic conditions, and potential future adjacent structures. The authors recommend using the AASHTO code value of 65 pounds per cubic foot (10 kN/m3) during concept design, followed by numerical analysis of rock wedges and stress measurement for final design.

Dec 1, 2022

By C. Patrick

Longwall face-to-face transfers can cost over $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high cost makes extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. This paper reports operations research techniques used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate over 30% of the total U.S. longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation models of transfers under varying conditions were generated; and, the economics of general transfers and time-cost tradeoffs in the transfer procedure were investigated.

Jan 1, 1993

By William W. Edgerton

Establishing geotechnical baselines on soft ground projects that require the use of closed-face tunnel boring machines (TBMs) is difficult. It is hard to see the face when mining and the excavated material is combined and mixed, all of which makes baseline quantifications challenging. In an attempt to meet underlying objectives of minimizing bidder contingencies, allocating or sharing risks and paying for conditions only if they occur, nongeotechnical baselines (i.e., functional baselines) have been developed. These have been used on the District of Columbia Water and Sewer Authority?s Clean Rivers (DCCR) Blue Plains Tunnel (BPT) project. This article examines the development of such functional baselines and how they were implemented on the BPT project.

Jan 1, 2012

By M. D. Flavel

Research programs conducted by Allis-Chalmers Corporation are showing that the most efficient energy use in crushers is achieved when the forces applied to particles undergoing breakage are increased. Laboratory bench scale tests have been developed to confirm this phenomena, which was first observed in the field using HYDROCOME crushers with automatic setting controls. A new testing machine is described and methods of maximizing such benefits are postulated. FOREWORD Allis-Chalmers Corporation was founded in Milwaukee, Wisconsin, in 1847 as the E. P. Allis Company, which had an initial interest in manufacturing components in the grinding of flour. As such, its roots were started in reducing material size, which is covered by the generic term, comminution.

Jan 1, 1981

By J. J. DeMull, B. A. Boster

Amax's Sleeper mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 t/d (500 stpd) to more than 720 t/d (795 stpd). Heap leaching was added to the process facilities in September 1986 at a design rate of 1.5 kt/d (1650 stpd) and current heap leaching rates exceed 2.7 kt/d (2950 stpd). Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1990

By M. S. Klima

Coal gasification solid residue (slag) contains unconverted carbon (char), which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal-3.4 mm gasifier slag (-85% ash) to separate high (-100%) ash slag from low (-50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71 % was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1mm in size.

Jan 1, 1997

By J. B. Webster

Health and Safety in the work place is of primary concern to the underground coal industry. Control of dust in the underground environment is of major importance in this concern. Utah Power and Light Mining Division has undertaken extensive studies to determine and control the various sources of respirable dust in underground high production sections. Determination of dust sources has been achieved by real-time aerosol sampling and standard gravimetric sampling on individuals and in various suspect locations. Some sources are diesel roadway dust, outby crushing, and handling equipment, face sloughing, water spray roll-back, and mining equipment. Once identified, the dust sources are suppressed or controlled and/or the workers are directed from areas of greatest potential exposure.

Jan 1, 1990

By T. Rudolph, M. Pawlik, J. Benndorf, X. Yin, J. F. Brune, P. Goerke-Mallet

The long and often undefined period in the post-mining phase challenges geo-monitoring with its various responsibilities, like the detection of environmental changes, ground movements and water management. Modern methods of geo- and environmental monitoring observe numerous aspects using active and passive sensors with multispectral, hyperspectral and microwave sensors, with diverse spatial dimensions and spatiotemporal resolutions from satellites, Unmanned Aerial Vehicles (UAVs), in-situ sensors. Data integration, together with on-site knowledge and experience, provides the basis for comprehensive modeling, which improves the understanding of the environmental changes and their related causes, which is an essential step for public acceptance. In this paper, we aim to give a brief overview of various geo- and environmental monitoring methods.

Mar 2, 2022

By D. Puckett

The feasibility of maintaining equipment location, personnel location and vital statistics in surface and underground mining operations has increased with advances in radio frequency identification (RFID) technology. The paper addresses the use of this technology, relatively new in the mining industry, to track surface equipment in mine pits, loading points, and processing facilities. Specific applications are discussed including a simplified and a complex truck tracking system and an automatic pit ticket system. The paper concludes with a discussion of the future possibilities of RFID technology in mining, such as monitoring biofeedback of personnel (heart and respiration rate, body temperature, exertion level, etc.) repetitious movements to study work habits, and logging air quality via personnel sensors.

Jan 1, 1996

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By P. Croney

Environmental monitoring requires major effort and expense but management of data receives less attention. A modem database system can manage hydrochemistry, water levels, meteorology, geology and downhole geophysics data and is flexible to allow the storage of ad hoc data. Reports can be customized by the user and derived data generated from input values. The production of high quality maps with contours and hydrochemical diagrams is an essential part of the reporting process. These maps integrate directly with the current site survey information. These facilities are best provided by storing the data in an industry standard database such as Oracle or Access to which customized AutoCAD and Microsoft Office routines make direct SQL calls.

Jan 1, 1997

By Paul B. Valenti

The Nevada Moly Operation of Anaconda Minerals Co., (a molybdenum/copper ore body) was initiated in 1978, with a contract to Bechtel Civil and Minerals Inc. for construction of a mining and milling facility near Tonopah, NV. Ground was broken on the concentrator portion of the project in August 1979$ with a multi-phased startup of the mill beginning in June 1981. Processing design tonnage of 20 000 t/d (22,000 STPD) was reached in early 1982. Major pitfalls of rapid design and implementation of engineering, construction, and startup are considered. The operation of the concentrator including SAG milling, ball milling, bulk rougher flotation, copper/moly separation, moly regrinding and cleaning, thickening, and product loadout are discussed.

Jan 1, 1983

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By G. A. Shirey

Breakthroughs in software technology and in computer hardware capabilities have opened new opportunities to develop more accurate process simulators and to reduce the operating time to reasonable levels. As a result, there are several new simulation packages being commercialized for modeling coal preparation plants and pulverized coal-fired power plants, and the users of these packages are reporting significant improvements in process efficiency and operating costs by implementing the simulators' results. This paper provides an overview of some of the models currently in use at CQ Inc., including the ASPEN PLUS"" Coal Cleaning Simulator, the Ultramax® process optimization software package, and EPRI's Coal Quality Impact Model?. Case histories of specific applications are also presented.

Jan 1, 1995