Search Documents

By Timothy C. Smith, S. Andrew Jacobs, Douglas E. Gonzales, Sandy J. Schexnailder, Carl Urban

At the Schwartzwalder Mine (Cotter Corporation, Golden, Colorado) ion exchange resins have been used in mine water treatment experiments. The experiments, initiated in October 1979 and currently in progress, demonstrate that mine water uranium values can be reduced to levels as low as 10 ppb. Duolite® A-101D, a strongly basic anion exchange resin, was tested in laboratory-scale columns (1 inch diameter) initially and then in pilot-scale columns (4 inch diameter), using both co-current and counter-current operational modes. Observations and conclusions resulting from these studies can be summarized as follows: (1) Duolite® A-101D appears to have successfully extracted uranium at influent levels of approximately 2.0 ppm over multiple loading and elution cycles, consistently producing effluent concentrations as low as 10 ppb uranium. (2) Based upon present test data, counter-current regeneration appears to be the key to successful operation. Upflow loading and downflow elution are the preferred modes for service and regeneration, respectively. (3) Filtration is a necessary pretreatment to remove fine clay and inorganic precipitates that will foul the resin, causing excessive pressure drop and poor loading and elution kinetics. (4) This waste treatment application is unique in that it offers the opportunity to recover some or all of the capital investment in the treatment facility

Jan 1, 1980

By Charles C. Y. Chen, Duane R. Skidmore

Batch leaching of Ohio #1, Ohio #4A and Ohio #5 coals was conducted with the thermophilic. sulfur, oxidizing microorganism: Sulfolobus acidocaldarius. Four different size fractions of each coal, with median sizes of 508, 200, 90, and 49 microns, were subjected for 10 days to leaching in a 5% coal-water slurry at 72°C and a pH of 2. Release rates and extent of sulfate and iron I1 and I11 ions from the coals during the leaching process and distribution of sulfur forms (sulfate, pyritic and organic) in the coal samples before and after treatment were determined. Data indicated that Ohio #1 coal, with an initial sulfur content of 0.6%, showed no significant changes with leaching in total sulfur content or forms of sulfur. The Ohio #4A coal, with initial total sulfur content near 5%, yielded product, for sizes below 200 microns with 90% reduction of pyritic sulfur while the extent of organic sulfur removal varied with coal particle size. Results similar to those for Ohio #4A were observed on the Ohio #5 coal, which had an initial total sulfur content of 3% and a final sulfur content near 1%. The findings were interpreted in terms of basic biological, chemical and physical mechanisms.

Jan 1, 1989

By Frederick T. Graybeal

Silver Bell is located about 56 km (35 miles) northwest of Tucson, AZ. It is a classic porphyry copper deposit containing enriched disseminated chalcocite ore in altered porphyritic rocks with chalcopyrite in adjacent skarn zones. The discovery of Silver Bell was an evolutionary process that occurred over a 75-year period. Recorded mining activity began about 1865 on Boot Hill east of El Tiro pit (see Fig. 1) where outcrops of altered limestones were found to contain 425 to 482 g (15 to 17 oz) Ag mixed with copper oxides. By 1874, the Young America Copper Co. was mining shallow occurrences of 30% Cu along the north side of the present Oxide pit. The ore was shipped by wagon to Yuma, AZ, and then by boat to San Francisco for smelting. By 1881, the district supported several mining companies, two small smelters, and was being favorably compared to Bisbee in local newspapers. Most of the ore mined in the period 1865-1903 came from pods of massive sulfide or their oxidized products which were distributed in an unpredictable fashion through a large skarn zone in Paleozoic limestone east of El Tiro pit. Ore grades varied from 5 to 10% Cu.

Jan 1, 1991

By V. Vesselinov, S. Orr

"Enhanced heap leaching - Part 1: Insights" (Orr, 2002), different flow and transport phenomena that could significantly reduce leaching recovery were investigated. The combination of such understanding with advanced flow and transport modeling establishes the link between cause and effect, thereby, directing operators to optimal design and construction of new heaps. Modeling of flow and transport in heaps could also point to a unique change in application method or rate that would maximize leaching enhancement of an existing heap under existing situation and leaching history. The use of such a model is cost effective in that it can simulate multiple scenarios of alternative leaching enhancement methods. By simulating a large number of irrigation scenarios, such a model can point to the optimal and/or the most promising alternatives for a particular heap. The authors' simulations concentrate on the effects of changes in application rates and heap design on changes in flow paths and enhanced leaching recovery. Based on such simulations, an intelligent control agent, such as Multiple Resolution Decision-Support System (MRDS) (Meystel and Albus, 2002), could build a new representation of the complex heap-leaching system. And, by learning from historical data and current information, it could provide optimal management of heap leaching and heap decommissioning.

Jan 1, 2003

By Keith G. Wallace, Gary K. Rogers

As a supplement to an analysis involving methodologies for the estimation of airflow resistance in shafts used for both ventilation and hoisting, a detailed shaft characterization survey was distributed worldwide. The survey provided detailed information which enabled verification of recommended velocities and established limitations on fill factors and relative velocities. This paper evaluates the information obtained for 37 shafts and presents a statistical evaluation of the results. Apart from airflow rates, conveyance rates, and physical characteristics, qualitative information regarding means of conveyance stability and velocity control techniques at unloading and loading points are also presented. Calculations of fill coefficient, free area velocity, and most importantly, relative velocity between the airflow and hoist, are conducted. These results are presented by frequency diagrams which illustrate the trends, as well as provide limitations for these parameters. The data illustrates that, commonly, the fill coefficient for two or more conveyances, does not exceed 30 %. A limit of 50% is suggested for a single conveyance shaft. A recommended free area velocity of 10 m/s (1,970 ft/min) for combined ventilation and hoisting shafts, is sup- ported by these results. Relative velocities of 30 m/s (5,905 ft/min) are most frequent and 50 m/s (9,840 ft/min) being a practical maximum.

Jan 1, 1987

By Alice Blount, F. Patrick Carr

The quantitative evaluation,of quartz and other minerals in acid-insoluble residues from carbonate rocks and other industrial mineral products derived from sedimentary and low-grade metamorphic rocks is difficult. Commonly there are a dozen or more minerals present, and the suites vary from sample to sample. Because of these factors, either the absorption coefficient must be determined on a sample to sample basis or an internal standard must be used. Internal standards in general use are unsatisfactory. For example, [A1203] is often present in product samples because of ceramic grinding elements used in their production; CaF and LiF have peaks which overlap or nearly overlap mineral peaks in the samples. A careful evaluation has shown that magnesium aluminate (synthetic spinel) works particularly well as an internal standard for these types of samples. Not only does it have few, strong diffraction peaks which do not overlap, the peaks are in the same 28 region as the minerals, usually quartz and silicates, for which quantification is desired. Spinel also consists of equidimensional particles without prominent cleavages; this promotes a random orientation of the minerals in X-ray diffraction mounts. In addition, spinel can be used to correct for loss of diffracted-beam intensity due to thin sample preparations which are often unavoidable.

Jan 1, 1991

By Simon Wright, Roland Heersink

In the past, the center of most companies' e-initiatives has been on reduction of indirect costs, such as selling and procurement. Recently, e-commerce has moved its attention from back-office functions into manufacturing, in order to significantly reduce direct operating costs. This paper describes many of the Web-Powered Manufacturing initiatives being employed across various industries, and relates them to similar opportunities being started within the mining and mineral-processing sector. The following opportunities are enabled by Web-Powered Manufacturing: • Collaboration with outside experts to extend their pool of resources • Management of remote and distributed operations • Tie-in of small operations to a larger operation • Monitoring a position in a JV operated by a partner • Managing a plant located in someone else's facility • Having a chemical supplier manage his inventory in a customer's tanks • Having an equipment supplier remotely troubleshoot his equipment installed in a customer's site • Having an additive supplier provide remote pro-active. guidance in optimization of a customer's operation • Having software suppliers take responsibility for the results of their applications • Outsourcing software and systems support by providing remote access Details of one of these opportunities are described in this article, and the benefits captured using this approach and the technologies necessary to make them a reality are emphasized.

Jan 1, 2002

The development of economical and effective treatment processes for solid and aqueous waste is a critical issue facing the mining industry today. Cyanide, nitrates and acid rock drainage are environmentally sensitive effluents that require treatment or containment for acceptable disposal. In situ biotreatment processes are an emerging technology (Thayer) for cyanide oxidation, denitrification, sulfide mineral alteration and metal re- mineralization. Biological cyanide oxidation is competitive with chemical treatment processes (peroxide, alkaline chlorination) for process solutions, spent ore and tailings detoxification. Microbial denitrification treats mine waste contaminated with nitrates from blasting, processing or nitrification of the host rock. Bio-alteration of sulfide minerals and metal re-mineralization may present the most cost-effective and environmentally acceptable method of dealing with sulfide tailings and leachate solutions. Field test programs for cyanide bio-degradation and denitrification of spent ore and process solutions were designed and run at two mines. Although the treatment bacteria and the application processes are similar, each waste presented site-specific problems for adapting the biotreatment processes. Some of the site problems include climate, ore geochemistxy, field bacteria production, waste microbiology and application engineering. This paper compares treatment design and results for cyanide oxidation and denitrification in heap detox treatments.

Jan 1, 1992

By Richard A. Williams

The design, modelling and simulation of solid-liquid mixers remains one of the least advanced aspects of minerals processing, due to difficulties in quantifying complex slurry hydrodynamics from first principles, and in acquiring reliable experimental data for model verification and development. This contribution describes the application of electrical resistance tomography (ERT) for three dimensional imaging of the concentration of mineral particulates in a slurry mixer as a function of key process variables (particle size, impeller type, agitation speed). It is demonstrated how ERT can provide a wealth of detailed data to allow model development, which ultimately will lead to much improved design capabilities and the generation of mixing models which could reside within Particle Process Simulators. This principle is illustrated using descriptions of mixer behaviour based on an empirical approach, although the measurement methodology described is equally suited to development of computational fluid dynamics models, cellular models or design approaches based on artificial intelligence. The experimental data can be built into a visualisation data bank, which acts as a "process toolkit" by allowing a library of process responses to be catalogued. Hence these data can be accessed for the purposes of model development, equipment selection, optimisation of operating conditions or testing on-line control strategies.

Jan 1, 1995

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987

By J. A. Hrabik

The feasibility of mining deep phosphate deposits by a borehole mining system was compared with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 46 m (150 ft) or greater. However, at 15- and 30-m (50- and 100-ft) thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasibility of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is used to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1987

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By Felicia F. Peng

Flotation process is particle hydrophobic surface-based separation technique. To improve the essential flotation steps of collision and attachment, and reduce detachment probabilities between air bubbles and hydrophobic particles, a selectively designed cavitaion venture-tube can be used to generate very high numbers of pico-nano bubbles to flotation column. Fully embraced by those high numbers of tiny bubbles, hydrophobic particles are readily attracting those tiny bubbles to their surfaces. The results of column flotation of Pittsburgh No.8 seam coal are obtained in a 50 cm ID and 162cm height flotation column equipped with static-mixer and cavitation-venture tube, using kerosene as collector and MIBC as frother. Design of experiment procedure combined with statistical two-stepwise analysis method are applied and attempted to made the optimizing the grade and recovery. The effect of independent variables on response has been explained. Combustible material recovery of 85-90% at clean coal product of 10-11 % ash are obtained from feed of 29.6% ash, with reduced amount of frother and collector than that used in conventional column flotation. The column flotation process utilizing the pico-nanobubbles can also be extended to the lower limit and upper limit of particle size ranges for better recovery minus 75 µm and 300-600 µm, respectively.

Jan 1, 2013

By J. Herbst, C. C. Harris, G. Poling

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale- down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Sep 30, 2021

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By Yuting Xue

Classification of rock and coal is one preliminary problem for fully automated or intelligent mining. It assists in automated rib stability analysis and enables the shearer to adjust the drums without human intervention. This paper studies the classification of rock from coal on rib images using machine learning techniques. A database of rock and coal images was created by filtering photographs taken by NIOSH researchers during site visits. Machine learning was conducted on patches, smaller images randomly extracted from each rock or coal image. After training, the classifier was validated with the testing dataset and achieved an accuracy score of 0.9.

Jan 13, 2022

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By G. A. Rosario, G. Peach

Twin 8.5 m diameter, 10 km long headrace tunnels under overburdens of up to 1870 m were excavated for the neelum jhelum hydroelectric project in north-eastern pakistan using two main beam gripper tunnel boring machines (tbms). Rock bursts were encountered and presented a significant danger to personnel and equipment. Micro seismic monitoring was installed to analyze rock burst characteristics and to create a database for future reference. Correlation of rock burst characteristics improved the ability to predict the likelihood, location, severity, and number of rock burst events. This paper presents the analysis of the micro seismic data

Dec 1, 2022