Search Documents

By Jim Jonas

The Berkeley pit-lake was sampled during two seasons, fall 1997 and spring 1998, from the surface to the bottom. Various parameters were measured to determine what effect the seasons had on the water column. It was determined that a seasonal turnover did occur between the fall and the spring sampling; however, the depth of mixing due to turnover could not be established. Trends were observed which suggested that microbial activity was altering the iron speciation at depth, and subsequently masking the extent of mixing. Various trace metals were removed from the surface water by either co-precipitation with schwertmannite or adsorption.

Jan 1, 2000

By Garry W. Warren

The electrochemical oxidation of chalcopyrite in the absence of-a chemical oxidant was studied in ammonia/ammonium sulfate solutions by anodically polarizing electrodes prepared from massive chalcopyrite. The effects of pH, cupric and ammonia ion concentration were systematically evaluated. Kinetic parameters were obtained from the anodic charge-transfer regions of the anodic polarization curves. Increasing ammonia and hydroxyl ion concentrations increased the rate of oxidation. A mechanism is proposed which explains the first order dependence of (NH3) and (OR) associated with a single electron transfer process. An empirical relationship which accurately describes the dependence of the rest potential (i.e. zero current potential) on solution composition is also given.

Jan 1, 1978

By Jr. Freed

Basic design features, details of the face ventilation system, roof support and Operator protection system, certified lighting, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, are reviewed. The AES is designed to help overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support and permanent roof support equipment. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1978

By M. Gorman

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately 74 miles southeast of Las Vegas, Nevada. The property has been owned by the Duval Corporation, Cyprus Mining Company and Equatorial Mining of Australia. Mercator purchased Mineral Park from Equatorial in 2003. Mineral Park commissioned a 25,000 tpd copper and molybdenum concentrator in November and December of 2008. The process includes two stage milling (SAG and Two Ball Mills) fed by primary crushed ore. Metals are recovered in a copper-molybdenum flotation circuit consisting of mechanically agitated roughers and cleaners. The copper- molybdenum flotation concentrate is thickened and further processed in the molybdenum flotation circuit which separates the copper and molybdenum minerals into salable concentrates. The molybdenum circuit also uses mechanically agitated cells. This paper describes the plant and some of the highlights of the commissioning process.

Jan 1, 2010

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971

By Edwin R. Phelps

Good morning ladies and gentlemen - today I am in an enviable position for two basic reasons - No. 1, since I am first on the program, the audience should start out awake because those that partied too much last night are still asleep, but in their room, not here. No. 2, since copper, iron, and mining technology are not competitive, the veracity of my statements will not be questioned. Most such meetings I attend are based on the subject of energy and the coal industry does have competition from oil, gas, hydro, and nuclear. However, to counteract this advantage I am the usual engineer with a limited vocabulary by schooling, and the remaining vocabulary almost completely eliminated due to the presence of ladies. In relation to the past of the coal industry, we have not only suffered the competition of other energy sources mentioned before, but in addition have in the last 25 to 30 years been required to meet the demands of a vastly changing market. To explain this statement, I am sure many of you can remember 30 to 40 years back when most homes were heated by coal furnaces or stoves and shudder to recall the shoveling of coal into the fire and the carrying out of ashes with the attendent manual labor dust. Now this space heating portion of our sales has almost become non-existant due to an almost universal switch from coal to natural gas, oil, and electric heating. Actual figures show a decrease from 119 million to less than 28 million tons per year in less than a twenty year span. Also, most of you can remember the coal burning steam locomotives and the tremendous volume of coal they consumed and then the very rapid change to the diesel-electric locomotives, incorporating improved large diesel engines driving D C generators and electric drive motors, which resulted in cheaper motive power. This change over was so complete that the annual tonnage of coal dropped from 125 million to less than 2 million tons in 15 years. 'Actually, now it requires some considerable interrogation and traveling to find a locomotive still operating on steam.

Jan 1, 1968

By U. Thorley

This paper presents an overview of surface mining activity in the Canadian oil sands and how the mine operators interact with the province of Alberta's Mine Financial Security Program (MFSP), which took effect April 1, 2011. The MFSP approach to reclamation assurance results in the government of Alberta sharing a portion of reclamation liability through the majority of an oil sand mine's life. In order to determine the potential fiscal magnitude of this shared liability, an examination of the expected costs of oil sands reclamation activities through a study of corporate asset retirement obligation (ARO) liabilities and other corporate disclosures is presented. The province of Alberta's Environmental Protection Security Fund (EPSF), which formerly secured oil sands mine reclamation activities is discussed. Reclamation costs in the oil sands are poorly understood. The MFSP provides what it characterizes as a conservative estimate of C$75,000/ha, while corporate disclosures by Canadian Oil Sands Ltd. place expected costs at C$180,000/ha. There is significant risk associated with the apparent uncertainty surrounding reclamation costs.

Jan 1, 2012

By Ralph B. Peck

Exploration The technology of underground construction and particularly of tunneling, both now and in the future, starts with knowledge of the properties of the medium surrounding the tunnel. Although we are trying to develop machines that can excavate tunnels independently of the properties of the medium, and although we may achieve some success in this direction, we seem always to be brought up short by a paradox: With increasing sophistication of machines and with increasing complexity of construction jobs, our methods are likely to become more sensitive rather than less sensitive to changes in the medium. I suspect that the need for more precise knowledge of subsurface conditions in advance of construction will increase rather than decrease as time goes by. In the recent anniversary issue of Engineering News Record, Probing the Future, Senior Editor Bill Jacobus prophesies highly sophisticated devices to probe the unknowns of the earth's soil and rock materials. He envisions that "drill holes to obtain borings will give way to rock-melting coring devices". He may be right; it is hard to argue the accuracy of predictions of the future. It seems to me more likely, however, that the rock-melting probe will be simply one more in

Jan 1, 1974

By J. David Lowell

This paper describes the geology of the Kalamazoo copper orebody discovered in the course of an exploration project carried out by Quintana Minerals Corporation under the author's direction in an area immediately southwest of the San Manuel mine, Pinal County, Arizona. In the period 1943-1947, exploration projects were carried out in the San Manuel area by the U.S. Bureau of Mines and Magma Copper Company which resulted in the development of the San Manuel underground block-cave mine which is now in production at a rate of 41, 000 tons per day. Mining claims covering the area immediately west of the San Manuel orebody were staked in 1946 by Frank F. Salas, R. A. Buzan, H. G. Buzan, and W. C. Buzan of Mammoth, Arizona. These claims were optioned to Martha Purcell in 1946, and in the period of 1947-1958 seven churn drill holes ranging in depth from 1,400 to 2,950 feet were drilled by Mrs. Purcell. These holes did not intersect ore and no further deep exploration was attempted prior to the Quintana Minerals project which began in August, 1965, and which is described in this report. The Kalamazoo deposit is in Sections 3, 4, 9, and 10, T 9 S, R 16 E, Pinal County, Arizona, and it is reached by driving seven miles east from Oracle, Arizona (Figure 1) . The writer is indebted to Corbin J. Robertson and Ronald B. Thompson who participated in the exploration planning of this project and to a number of other individuals who contributed to its execution and management. Petrographic work by J. M. Guilbert was used as a basis for rock and alteration classifications.

Jan 1, 1968

By Thomas R. Yanske, Jonathan E. Carmack, Lyndon M. Clark

In order to maximize the extraction of high grade pillars at The Doe Run Company, artificial pillars are created using cemented rock fill (CRF). CRF pillars aid extraction of pillars in two ways. One is to offer back support for the immediate area where pillars are being extracted. The second is to increase the post failure residual strength of pillars surrounded by backfill. The CRF is produced using a combination of minus 1.0 m run of mine (ROM) rock and minus 5 cm crushed rock. Depending on the operation the CRF slurry is either produced in an underground or a surface batch plant. The slurry and rock are transported to the fill area by truck where they are mixed and placed in 1 m lifts. To reduce the amount of CRF needed, fill fences are constructed around the perimeter of the CRF pillar. Within these fences ROM CRF is placed in lifts until within 0.6 m of the back after which minus five centimeter CRF is slung tight to the back utilizing slinger trucks. In constructing these artificial pillars a number of set procedures have been established to ensure that the work is done both properly and safely.

Jan 1, 2001

By Russell Clough

The Pacheco Pumping Plant is situated on the west end of San Luis Reservoir in western Merced County, California. It is designed to draw water from the reservoir and pump it into a 3,500,000 gallon regulating tank. The water then flows entirely by gravity to the Coyote Pump Station in Morgan Hill, a distance of 40 miles, where it is pumped into Anderson Reservoir. This water is used to recharge the depleted groundwater table in the Santa Clara Valley. Eventually, some of the water will be diverted to Hollister in San Benito County and to Watsonville and Santa Cruz in Santa Cruz County. The owner is the United States Bureau of Reclamation. The underground work consisted of a fifteen foot finished diameter surge shaft 250 feet deep to the crown of the pump chamber; a twenty foot finished diameter pump chamber which declined from the shaft at 14.2% for ninety feet and then ran horizontally for 180 feet; and twelve each five foot diameter steel lined intake shafts 240 feet deep which intersect the pump chamber in the horizontal section. (Figure 1) Upon completion of the pump chamber, the contractor had to dewater the existing tunnel under the reservoir, excavate the remaining fifteen foot plug, and concrete the transition. The low bidder for this contract was Underground - Continental-Heller at 414,456,000. Excavation of the open cut for the pumping plant and surge shaft began on April 14, 1983. This was performed using a Koehring 1066D backhoe, dozer, trucks, and two Cat 631 scrapers. The excavation was started at the surge shaft so that the grouting could begin

Jan 1, 1985

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By G. E. Erdman

This paper presents talc milling guided by a theme of "So You Want to Be In The Talc Business". Such a theme strikes a cautionary note to warn the uninitiated of potential pitfalls, and this paper will cover briefly some of the technical traps as well as one of the larger talc milling operations. It is important to our purpose to pre- sent some of the market and mineral complications that make the business of producing and selling industrial talcs much more intricate than an outsider would perceive. Metal markets by comparison are great worldwide pools into which production streams of generally identical metals can flow over a weir of market prices. Industrial talc markets are not as well defined and often must be developed by the producer working closely with a specific customer or groups of customers to prove out the attributes of the specific product from a new property. All the negatives of a new market seem to work against the introductory talc in the forms of industry or customer reluctance to change, sales prices, cost of delivery, mode of transportation, health considerations of the minerals and many more. Just locating the potential customers for a new industrial talc may be a substantial undertaking. Thus, an analogy of the worldwide metal market might compare starting a new talc operation to trying to gather up enough fallen rain drops to be able to start a production stream of a worthwhile size.

Jan 1, 1984

By H. G. Wickes

Virtually all fluorine consumed by the aluminum industry is as the electrolyte of the Hall-Heroult process for producing primary aluminum. A small amount of fluorspar is used but most fluorine is consumed as either aluminum fluoride or cryolite. Some fluorine- containing materials are used in secondary aluminum production, but the amount is negligible compared with primary production requirements. Any analysis of the future of the primary aluminum industry must take into account two powerful and closely related driving forces which are shaping that future. These factors are increasingly stringent restrictions on the emission of pollutants and the continuing cost-price squeeze. Nowhere do these factors combine more forcefully than in the area of fluorine consumption. We can safely assume that industry efforts to reduce fluorine consumption will be intensified and that these efforts will be fruitful. This paper will attempt to identify and quantify the factors and trends of fluorine consumption during the next decade. We will be concerned primarily with the demand for new fluorine. Sources of new fluorine will not be treated.

Jan 1, 1973

By Gerald Zink

The object of underground excavation--apart from mining-- is to create an opening to serve as a part of some useful structure. The value of the opening lies in its conformity to the design configuration and its stability during the planned life of the structure. The wire saw could be used to excavate openings of high value at a cost competitive with present methods. First, a discussion of present methods will be used to explain where wire sawing fits in and how it should be applied. PRESENT EXCAVATION METHODS Tunnel Boring A recent advance in tunneling technology is the use of mechanical boring machines. There are many ways that a boring machine can reduce the cost of a tunnel or increase its value. I will mention a few of the advantages that have been demonstrated in tunneling projects. A tunnel can be bored without overbreak, allowing concrete lining to be poured to the design thickness without waste. Boring creates a minimum of disturbance to the tunnel wall, preserving the natural strength of the rock and reducing the amount of support which must be installed to maintain stability. A boring machine maintains the tunnel at its full dimensions and proper shape, and it leaves no rock projecting from the wall which must be trimmed off. The use of boring machines is presently limited to openings of uniform cross section and great length. If the previously mentioned attributes of mechanical boring could be applied to excavation of a wide variety of chambers and passages, then a corresponding decrease in cost and gain in value would be possible for chambers.

Jan 1, 1974

By S. E. Phifer

The Haile Gold Mine was the largest gold producer east of the Mississippi River prior to 1942. It is currently the only producing gold mine in the Southeastern United States. Current development involves the mining and heap leaching of some 1000 TPD. Carbon is employed as a recovery medium. Due to its clayey nature and excessive fines in the oxide ore, agglomeration using Portland cement is required prior to leaching. The ore ranges in screen size from two inches to -200 mesh. The agglomerating step combined with certain other conditions has enabled Piedmont Mining Company to achieve recoveries of 90%.

Jan 1, 1987

By David D. Eyer

Since the decade of the 1990s is nearly upon us, I have focused on what I see are the likely trends featured in new large underground coal mines 10 years from now. I do this from the vantage point of having been involved in the installation of large mines for more than twenty years. Little of the equipment resources we have available today was unknown when I entered the coal business in 1960. There were continuous miners, longwalls and diesel-powered equipment in Europe, monitoring systems, computers, heavy media separation systems, froth flotation and conveyors then as there are now. A substantial evolutionary process has occurred with these and other mining machines and processes. Some evolved only to die out, such as boring-type continuous miners; others, such as longwall systems, flourished. My intuition tells me that since there have been largely evolutionary rather than revolutionary developments in the near past, the same is true of the future, at least for the next 10 years. In other words, the elements of what are in the future are with US now. Some, such as computer-based applications, may evolve beyond our wildest dreams -but I doubt it.

Jan 1, 1988

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

The Tolt Pipeline No. 2, West Snoqualmie Valley project, is part of a water supply project linking the Tolt reservoir in East King County to the City of Seattle through a nominal 2.13 m (7-ft) inside diameter conveyance. Receipt of the National, 2002Microtunnel Award provided recognition of the many challenges overcome by this project. Baseline conditions revealed in the Geotechnical Documentation included over-consolidated glacial deposits, landslide and alluvial deposits, artesian water, boulders up to 36-in in diameter, logs, heaving sands, and liquefiable soils beneath the river. Schedule constraints associated with setting the shafts in the floodplain of a salmon bearing river and the fickle performance of the river during those times it was not supposed to flood added to the challenge.

Jan 1, 2003

By Waclaw Dziurzynski, Janusz Tracz, Danny Wooton, Andrzej M. Wala

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009