Search Documents

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By D. Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 “Welded Steel Conveyor Pulleys” adequately defines standard pulleys for most aggregate material handling applications. However, many aggregate applications demand pulleys of higher capacity and reliability than that offered by CEMA pulleys. This paper examines the CEMA Pulley Standard and pulley specifications for aggregate applications requiring greater capacity and reliability than the CEMA Pulley Standard. Higher reliability increases the uptime and has a lower total cost of ownership.

Jan 1, 2003

By Joseph L. Margin

From a stubborn start to record setting performances in little over a year, that is the story of the English Running Tunnel Boring Machines. The program to transfer technical information on these highly advanced machines from builder to user will be discussed as a vital link to this accomplishment. Some interesting features of these machines will be covered as well as a recounting of the various conditions that were encountered during these drives and how they were resolved.

Jan 1, 1991

By Mahmut Yavuz

to in Old Uighur Turkish as Tolay kopugu, in Ottoman Turkish as Derya kopugu, and in modern Turkish as Luletasi. Scientifically known as sepiolite, it is represented by the formula Si12Mg8O30(OH)4(H2O)4(8H2O). Sepiolite is a natural clay mineral composed of hydrous magnesium silicate, characterized by a structure of alternating blocks and tunnels that develop in the direction of the fiber. Each structural block contains two silica tetrahedral sheets surrounding a central layer of magnesium oxide- hydroxide. Sepiolite exists in two distinct forms in nature: alpha-sepiolite and beta-sepiolite. Alpha- sepiolite is amorphous, compact, and resembles pellets that look like sea froth, hence its Turkish name Luletasi. In contrast, beta-sepiolite appears as amorphous aggregates or small, flat, round particles. These two forms exhibit different physical properties. Meerschaum was also studied by Brauner and Preisinger in 1958, who agreed that it primarily consists of sepiolite (2MgO·3SiO2·nH2O). According to these researchers, water is present in its mineral, zeolitic, crystal, and structural forms. Meerschaum is commonly used for adsorbing various liquids, as an ion exchanger, and for dispersing and insulating paraffin in the chemical industry (Gokdemir and Dogan, 2011). Sepiolite deposits of the meerschaum type are primarily found in Turkey, Somalia, Tanzania, Kenya, and Mexico. Alongside high-quality, low-density, and highly porous meerschaum, Somalia also has sedimentary sepiolite formations. The total reserves of these deposits are estimated at around 50–100 million tons (Sariiz and Isik, 1995). Meerschaum, also known as “white gold” or “sepiolite,” is a unique mineral highly prized for its lightness, heat- resistant properties, and ability to be carved into intricate designs. Found predominantly in Eskisehir, Turkiye, meerschaum mining and processing have become significant contributors to the local economy and cultural heritage. This paper explores the history, economic importance, mining practices, and environmental impacts of meerschaum mining in Eskisehir and discusses the challenges and opportunities faced by the industry.

Feb 1, 2025

By K. Fountain

In Novemeber of last year I visited a mica mine in Hunan Province, China. For nine months , we had been trying to sell Chinese mica to a customer in Belgium. Talking to the customer was like negotitating with a stone wall. The buyer refused to communicate any -thing other than his steadfast refusal to consider Chinese mica. He would not advise us what he wanted, what specifications or grades. He would give no indication if our price at market, or reasonable, or totally out to lunch. He would not even accept samples. It took no genius to guess that the mica buyer had at some time in the past bought a shipment of Chinese mica and had received a disaster. I invited the mica mine in Hunan in order to see for myself what could be done - without massive investment in equipment and instruments - to upgrade the quality of the mica for export. We had seen this type of customer reaction before. One disgruntled customer who had pur¬chased pigment grade barites direct from China ranted and raved about unreliable and inconsistent quality. It did no good to explain to him that China is a big country, with hundreds of mines scattered throughout many areas, each producing a different product. Our further explanation that Chinese export organizations also varied in degree and efficiency of customer service fell on deaf ears. Samples had no effect on his perception. Eventually we showed him photoraphs of two mountains of pigment grade barites. One lot was our sales of pigment barites to a major European minerals processor. Our Chinese barites stood proudly white and beautiful next to a hill of other material which now appeared at best mediocre and dull by comparison, and which the buyer had decided to reject after he received our Chinese barites. Finally the customer was sufficiently impressed to look seriously at our guaranteed specification and the outturn analysis performed by our other customer.

Jan 1, 1987

By James J. Kabat, James A. McDonald

Impregilo/SA Healy JV recently completed this Project using the first slurry shield TBM’s in the United States. The Project used two TBM’s to mine 18,000 feet in sands, gravels, and silty alluvial materials under the Willamette River and downtown Portland, Oregon. This paper discusses alignment and geological conditions, equipment selection and plant setup, and tunnel excavation means and methods, parameters, and results. Extensive hyperbaric operations were required and will also be discussed.

Jan 1, 2007

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By Charlie Sons

Pit and underground mine operators typically use a lot of big equipment tires. Just as typically, they spend a lot of money they shouldn't on these tires. That's because tire use and maintenance are not given enough attention. That often occurs because mine management and personnel do not know the basic facts of tire use and care. If a piece of large equipment is damaged or ruined, a good explanation better he forthcoming. A ruined tire is often just a shoulder shrug. But that sort of fatalistic acceptance can cost tens or hundreds of thousands of dollars a year extra for big equipment tires. That does not have to be. There are some basic tire considerations that, if followed, will extend tire life and lower tire costs. Most companies have the inevitable conflict between the production department, which resists any restrictions that may reduce productivity, and the maintenance department. Production success is based on meeting a schedule of yards moved, while maintenance success is based on availability and equipment cost. When production falls behind schedule and equipment speeds are increased, maintenance may soon find its tire costs rapidly increasing, unless everyone understands the tires' vulnerability to damage. Unless the production department understands the problem, or restraint is applied by top management, costs may become exorbitant. At one job site, tire costs alone exceeded $250,000, to move 55 dam3 (72 000 yd3) of dirt on an 11-km cycle. The operation temporarily caught up with its schedule, but tire costs and attendant downtime soon made this a not-for-profit exercise. Because an operator must always attempt to move payload at the lowest cost, there are cases when higher than normal tire costs must be accepted. For example, in pioneering work with tandem engine scrapers, steep grades shorten tire life to less than normal. But the steep grades make shorter haul cycles possible, yielding more trips per hour than alternative earth-moving methods.

Jan 1, 1982

By F. C. Nicolli, J. P. Barbosa, P. S. M. Soares, A. V. Estevez

INTRODUCTION Spent household dry cell batteries are frequently disposed of with metropolitan wastestream (MSW) in landfills where they can leak due to handling or aging. Frequent rain and sun cycles, especially in tropical environments, coupled to the action of leachate, dissolve their metal constituents which will eventually reach rivers, lakes and underground water. It is well known that some of these metals are fundamental to sustain life and that is why living organisms concentrate them through their metabolism, but it has been also recognized that beyond specific limits they can definitely be deleterious to the environment. In other words, high concentration of heavy metals are proven to cause chronic or acute diseases and toxic reactions, by acting on mammals' kidneys, liver and nervous system. In addition, some metals frequently used in household batteries, as mercury and cadmium, are said to be carcinogenic (Landis et al. 1995, Silva et al. 1988). Occasionally, plants to treat MSW are coupled to compost production. Household batteries present in MSW can be dragged into these plants, contaminating their products and eventually reaching vegetables making them not proper to consume by people and animals. Alternatively, batteries are also conveyed to incinerators and burned, throwing into the atmosphere volatile species. These can either act as contaminants as toxic vapor species or be delivered by winds and scavenged by rains contaminating soils and water far away from their source. In conclusion, despite the treatment applied to MSW, one can say that battery residues are potentially environmentally hazardous. The careful assessment of the environmental impact caused by residues of household batteries it is not an easy task and it can be referred as a multivariable problem. First, many different household batteries are produced by industry and the potential environmental hazard associated to their disposal depends primarily on the type of battery and manufacturer's technology. These characteristics will dictate how resistant the battery case is to handling and the

Jan 1, 1998

By V. Castranova, L. Wu, K. Van Dyke, J. Gutierrez, V. Vallayathan

Since it has been demonstrated that silica caused phagocytic cells to activate lipoxygenase metabolism of unsaturated fatty acids we thought selective inhibition of this metabolic pathway might be helpful in treatment of silicosis. It is known that lipoxygenase metabolism plays a role in the pathogenesis of a variety of inflammatory and hypersensitivity conditions. Further, it is believed that the alveolar phagocytic cells which engulf silica begin the inflammatory cycle which produces the metabolic products, cytokines and growth factors which causes fibrosis in the lung. There have been indications that drugs which inhibit lipoxygenase can inhibit fibrosis from other causes. Previously, we developed a method which detects the activity of lipoxygenase metabolism by measuring free radical oxidation via light production or chemiluminescence (CL). We decided to apply this method to phagocytic cells that would be found in the lung in the presence of silica with and without newly developed inhibitors of the lipoxygenase reaction. We used drugs which inhibit lipoxygenase directly including AA861 (TAKEDA), A63162 (Abbott), and an inhibitor that scavenges free radicals produced from the lipoxygenase reaction, nordihydroguairetic acid. In addition we used an indirect inhibitor, tetrandrine. We found drug inhibition of silica activated CL from alveolar macrophages, neutrophils and human leukemia (HL-60) cells differentiated with DMSO. Nordihydroguairetic acid 2x10-5M produced almost complete inhibition in all three cell types. In human leukemia cells (HL-60) A63162 and tetrandrine were equally inhibitory at 42% while in human neutrophils A63162 and tetrandrine were less active 22 and 10% respectively. In macrophages A63162 and AA861 were less than 50% inhibitory to cellular CL at 2xl0-5M. Direct assay of tetrandrine (2x10-5M) with sodium arachidonate and soybean lipoxygenase reveals no inhibition. All antilipoxygenase drugs regardless of mechanism were inhibitory to cellular chemiluminescence from all three types of phagocytic cells. These drugs alone or in mixtures could prove useful in treatment of silicosis.

Jan 1, 1991

By Ron Jackson

The report gives a general method for the geological evaluation of a gold deposit. Recognizable parameters associated with gold mineralization are used to develop a model of an orebody. The California Mother Lode is used as an example.

Jan 1, 1987

The authors give a corrected form of the Korobov algorithm of optimal open pit determination and describe a method of optimising the mining sequence within a preliminary pit design. A method of automatically including roadways is also given.

Jan 1, 1992

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The mining industry faces pressure to provide metals for the green digital shift using sustainable technologies. This study evaluates biosurfactants as collectors for ultrafine and coarser particles of hematite and malachite, aiming to improve the flotation of ultrafine particles.

Jun 1, 2023

By G. R. Robinson

Aggregate resources consist of sand and gravel, and crushed stone. They are large-tonnage, bulk-minable mineral commodities that are used in construction and industrial activities (Tepordei, 1999, 2001).Rates of aggregate production, use and mine permit approval in the mid-Atlantic region differ by population density. These rates are influenced by economic and human factors, such as demand, costs, land availability and community opposition. In some areas, the local availability of aggregate is limited. This is due to the lack of suitable local source materials for aggregate, the loss of potential high-quality aggregate resource production sites by preemptive land development and restrictive zoning (resource sterilization), and the difficulty of developing and permitting production sites for aggregate.

Jan 1, 2004

By Neville Slade, Doug Shumway, Dayan Anderson, Joe Siefke, Curtis James

The Mojave Desert is a particularly fragile ecosystem that faces several significant impacts. These include rapid housing development, overdrafted water supplies and loss of wildlife habitat — all a result of mining, industrial activity and urban sprawl. During the past three years, a diverse group of educators, natural resource managers and business leaders was assembled under the auspices of a local community college. This group’s goal was to provide unique natural resource education opportunities for the region.

Jan 1, 2005

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By J. M. Ekenes

New approaches that increase hydrometallurgical recovery from refractory minerals in below-mill-cut-off-grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyrite-bearing ore at Freeport-McMoRan?s mine in Morenci, Arizona. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation.

Jan 1, 2012