Search Documents

By S. J. Swan

A computerized on-line process control system designed to monitor and control the seven-cone copper precipitation operations at Kennecott Copper Corporation's Chino Mines Division in New Mexico has been continuously operating since April, 1972. The cone monitoring system consists of plant sampling components, process measurement instrumentation, on-stream X-ray spectrometer, control computer, typewriters for programming and for operating reports, foreman's communication console, and cone automation hardware. The system provides the following functions: (1) assays for copper and iron from ten process streams on a continuous rotating basis, (2) directs hardware to automatically flush and start up cone units based on measured performance variables, (3) provides continuous plant operating data and calculates metallurgical averages as well as production figures for shift and daily summaries, and (4) provides data logging capabilities. The system is very reliable and improves plant performance by increasing yields, reducing scrap iron consumption, and reducing operating manpower requirements.

Jan 1, 1975

By Kousik Sinha

The advantage of using a clean coal as a feedstock in a direct liquefaction plant is improved performance of the plant by several factors e.g., increased throughput of coal; reduced wear and tear of valves, pipes, and pumps; increased liquid yields, etc. This paper examines the technical feasibility for cleaning Illinois #6 coal as a feedstock to a direct coal liquefaction plant via selective agglomeration using a coal-derived heavy distillate, Wilsonville V-1074 as agglomerant. Effects of addition of Kerosene or coal-derived Naphtha as conditioner, coal particle size, slurry pH, oil to coal ratio, and operating temperature on ash reduction and clean coal weight recovery have been studied. Results show that about 70% of the ash can be removed from this coal and the clean coal weight recovery over 85% can be achieved by using this technique with suitable selection of coal particle size, slurry pH, mixing intensity and oil to coal ratio.

Jan 1, 1991

By Walter R. Lawrence

Newmont Gold Company, formerly Carlin Gold Mining Company, is a publicly owned corporation, 95% owned by Newmont Mining Corporation. Newmont Gold Company has operated gold recovery operations North of Carlin, Nevada, since 1965. Development of the Gold Quarry ore body, 19 kilometers south of the original mine, resulted in the decision to construct gold recovery and ancillary facilities in what is referred to as the Southern Area. Plant No. 2, located 11 kilometers North of Carlin, Nevada, was designed to treat 6350 tonnes per day of oxidized gold bearing ore assaying 2.5 grams per tonne of Au at an average recovery of 87%. Flowsheet development conducted by Newmont personnel resulted in the decision to construct a carbon-in-pulp recovery circuit preceded by two-stage grinding, Detailed engineering was done at Toronto by Bechtel of Canada beginning on January 1, 1984. Actual construction began on March 1, 1984, and was completed in June, 1985. First feed was run on June 22, 1985.

Jan 1, 1987

By Henrique D. G. Turrer, Robert F. Winterfield, Jobe E. Wheeler, Marcello R. Cru, Baojie Zhang, Pedro P. Pinto

Efficient particle classification is essential to enhance gravity and magnetic separation stages in one iron ore beneficiation plant. This study investigates the use of high-frequency screens to process finely ground iron ore, focusing on two size cuts: 400 μm and 100 μm. Pilot-scale trials were performed on four ore blends using a full-scale screening unit. A total of 48 tests were conducted, evaluating the effects of panel aperture, solids concentration, wash water, and feed particle size distribution. Results showed that wash water improved efficiency by up to 5%, while a solids concentration near 40% w/w delivered high separation performance with minimal ultra-fines in oversize streams. Apertures slightly larger than the target cut sizes yielded better precision in particle separation. Feed particle size distribution had limited impact on efficiency. The investigation successfully identified optimal screening conditions, including aperture selection, to achieve the most effective separation performance for downstream concentration processes.

Feb 22, 2026

This review provides a new and comprehensive summary on studying colloidal interactions encountered in mineral processing with representative examples for critical information, which are of great scientific and practical importance. Colloidal interactions play a vital role in mineral processing, including grinding, physical separation (particularly flotation), dewatering and tailings management (Fig. 1). Despite great energy input in comminution to liberate valuables from gangues, hetero-coagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. The importance of colloidal interactions is becoming increasingly significant as we process ever more finely disseminated low-grade ores as a result of inevitable depletion of high-grade ore deposits. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. 

By L. A. Clark

Although vein-, syenite-, and pegmatite-type deposits are known in Saskatchewan, recent intense exploration stems from discovery of several exceptionally high grade uranium and uranium-nickel deposits locallized near the basal unconformity of the 1.3-1.4 b.y. Athabasca Sandstone Formation. Graphitic basement rocks and post-Athabasca faulting or brecciation coincident with the unconformity are important in locallizing uranium deposits which form as tabular, shoe lace-like bodies with grades averaging over two percent and containing up to 50,000 tonnes U308. Some deposits have similar nickel contents. A few published sandstone analyses average 0.8 ppm uranium while basement granitoid and meta-sedimentary rocks vary from 0.5 to 20 ppm. In the proposed genetic model, traces of uranium are leached from these rocks by oxidized formation waters sweeping through the sandstone and along faults. Solutions are reduced and uranium is precipitated as basement graphitic meta-pelites are encountered along brecciated fault zones.

Jan 1, 1979

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By John H. Bassarear

Large scale equipment can reduce both capital and operating costs for concentrators. Large semiautogenous mills can be effectively utilized in big mills but they must be kept fully loaded to take advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semi- autogenous mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4,476 kW (6,000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 mtpd (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and five variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1985

By Jr. Stokowski

Topsoil for revegetation projects is in demand in many urban areas. In this case history, a large aggregate producer manufactured a topsoil from three waste materials. The topsoil was produced in a 200,000 m2 (50-acre) abandoned gravel pit that still had additional gravel under 10 m (30 ft) of overburden uneconomic to strip directly. The topsoil was produced by rotary mixing of sludge, overburden, and a lime admixture; solar drying; and stripping and stockpiling of the product. A major problem was an increase of topsoil drying times for stripping from 40 to over 100 hours when it was rewet by storms. The problem was solved by a research project that evaluated over 50 formulations and over 20 waste materials. . The final formula dried in 15 hours and contained 3-parts sandy mine spoil, 1-part sewage sludge, and 2 % spent-bed, a granular quick-lime produced during power-plant flue-gas desulfurization.

Jan 1, 1988

By M. Deniz Turan, HASAN NIZAMOGLU, Z. ABIDIN SARI, Tolga Depci

Chalcopyrite extraction in an aqueous acid medium occurs through solid transformations into distinct intermediaries. As intermediates, mineral phases CuS, Cu2 S and Cu5 FeS4 may generate in the leaching solution before CuFeS2 completely decomposes to Cu2+, Fe2+ and S0. Oxalic acid is a common organic acid, and it dissolves easily in warm water. Due to the chelating feature of oxalic acid, it hinders iron precipitation by composing soluble complex anions in a wide range of pH. In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using hydrochloric acid (HCl). Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp= 4.43 × 10 −10) was performed by conventional leaching in the presence of HCl.

By F. Scott Carpenter

During the past several years, more frequent reference to Wollastonite has appeared in print, both in this country and abroad. The reason for this is the apparent growing interest in this mineral as it approaches commercial maturity. Twelve years ago, wollastonite was available in only limited commercial quantity. In 1933, a deposit in California was worked for a short time to provide a calcium silicate raw .material for the manufacture of mineral wool* It was not until the spring of 1953 that Cabot Corporation put into operation a modem commercial plant to produce this material in a variety of grades. These grades covered both a range of particle size and of particle shape. At that time, applications for wollastonite were largely speculative, although a few commercial applications in glass frits and welding fluxes did exist, For all practical purposes, it was a new material for which few commercial uses had been fully proven.

Jan 1, 1964

By Diane Jones, Jeremy Spearman, Tom Matthewson

Requirements for minerals are on the increase globally and the deep sea offers a potential source of essential materials. Extracting these minerals from what is considered an environmentally sensitive area, and one about which little is still known, is a challenging activity, which needs careful consideration and an appropriate environmental impact assessment to be carried out. Extraction of material from the deep sea beds can cause disturbance or damage to benthic communities; impact on mobile marine species such as fish, mammals and reptiles; cause increases in suspended sediment and sediment deposition onto potentially sensitive areas or potentially release contaminants which were previously bound to the sediment. This paper discusses the potential environmental issues surrounding extraction of deep-sea deposits using aggregate dredging techniques and how those issues can be appropriately assessed. In particular issues of suspended sediments, plume transport, water and sediment quality and underwater noise impacts on potentially sensitive species and habitats will be explored.

Sep 1, 2014

By B. R. T. Simoneit

The formation of petroleum is normally thought of as a geologically lengthy process, involving the accumulation of organic matter, its gradual burial, diagenetic breakdown via geochemical reactions, maturation, heating within a 75-150'C "oil window" induced by normal geothermal gradients in the subsiding basin, and slow product migration into structural traps (Tissot and Welte, 1984, Hunt, 1979). The entire process can take millions of years and, indeed, most oil reservoirs probably formed in this manner. How-ever, today in sedimented, submarine rift basins (Fig. 1), Cl to >C40 hydrocarbons with the chemical and physical properties of crude oil are forming in demonstrably much shorter time by rapid thermal maturation of immature organic matter in hydrothermal regimes that are unusually high for sedimentary basins (Brault and Simoneit, 1988a, b; Didyk and Simoneit, 1988; Kawka and Simoneit, 1987; Peter et al., 1988; Simoneit, 1983; 1984; 1985a,b; 1988; Simoneit et al., 1984; 1987; 1988).

Jan 1, 1989

By Richard H. Johnson

White Pine Copper Company began operating a plant designed to recover copper matte particles from its discarded reverberatory furnace slags in April, 1972. Seasonal operation, generally the months of April through November, continued through October, 1974, shutting down due to feed exhaustion. White Pine reverberatory furnace slags contained economically recoverable amounts of copper for a variety of reasons. Among them: 1. White Pine concentrates yield extremely high matte grades (65+% Cu) and viscous slags. The viscous slags hinder matte settling causing matte "prill" entrapment in the slag 2. White Pine's total refined copper output is accomplished through fire refining requiring special techniques for impurity removal, especially small amounts of nickel introduced from purchased pyrite and chalcopyrite fluxes. These special techniques result in high-copper slags, refractory to smelting, being reintroduced into the reverberatory furnace. 3. Furnace bottom build-ups resulting in mechanical matte entrapment through the formation of "dams" hindering matte flow. 4. Occasional concentrate fluxing and furnace atmosphere control problems.

Jan 1, 1975

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

By Joseph Cervik

Common methods of controlling gob gas in U.S. nines are by means of ventilation of gob areas and gas drainage through surf ace boreholes. Costs of drilling surface gob holes increase as deeper coalbeds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States, This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1979

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By D. M. Stephens

Feeder-Breakers were an unknown but much needed piece of machinery when U. S. underground coal mines started converting to more efficient belt haulage of the R.O.M. coal as compared to conventional methods that the 1950's offered. These simple electromechanical machines offered efficiencies in three areas: (1) they contained a surge hopper that allowed a "load' of coal to be dumped without delay; (2) this material was fed horizontally by a drag chain conveyor into a rotating carbide pick breaker that broke all oversize material into a beltable size, and (3) it fed this broken material onto the belt conveyor at a rate conducive to its design. Since its introduction, the Feeder-Breaker has evolved from that first low capacity, low breaking force machine to today's model capable of breaking materials up to 5 MOHS in hardness and having throughput capabilities exceeding 3,000 TPH with availability in the 90 percentiles.

Jan 1, 1985

By Andrea Koschinsky, Akira Usui, Michael Bau, Katja Schmidt, James Hein, Thomas Kuhn

Marine ferro-manganese (Fe-Mn) crusts and nodules are metal-rich chemical sediments that are archives of paleoceanographic proxies and potential metal resources and targets of deep-sea mining. Traditionally, crusts and nodules are subdivided into hydrogenetic, diagenetic, and hydrothermal types. While hydrogenetic Fe-Mn crusts are a potential resource for Co, Te, Pt, and REY, nodules are enriched in Cu, Ni, Mo, and Li, and hydrothermal deposits may be enriched in individual metals such as Mo, Ba, and Li, depending on the temperature and composition of the hydrothermal fluid. The different types of marine oxidic Fe-Mn precipitates, therefore, have different economic potential. Hence, a robust classification is not only helpful in the general geochemical characterization of such precipitates (and as such is a useful teaching tool, for example), but may also simplify the evaluation of their importance as a potential metal resource, which helps to prioritize exploration targets for deep-sea mining.

Sep 1, 2014

By K. S. Liddell

Ultra fine grinding is becoming increasingly used in the mining industry over recent years. The development of large-scale units for high volume grinding of low value materials and concentrates has opened up new areas of economical metal extraction. The ability of stirred vertical mills to produce very fine particles with high surface areas, is providing mine operators with novel extraction possibilities within gold concentrate regrind for Biox or leach feed, Activox autoclave feed preparation and lime slaking operations. The paper will review design, operational and maintenance aspects of ANI-Metprotech stirred vertical mills, comparing these to tower mills, horizontal bead mills and attrition mills.

Jan 1, 2001