Search Documents

By J. J. Poveromo

"Iron ore for alternate iron processes concerns alternate iron products designed for use in EAF (electric arc furnace) steelmaking processes. These alternate iron products include both DRI (direct reduced iron), HBI (hot briquetted iron) and merchant pig iron. Merchant pig iron can be produced in conventional blast furnaces, mini blast furnaces (including charcoal BF's) or novel processes such as RHF/SAF (rotary hearth furnace/submerged arc furnace) such as Iron Dynamics or RHF such as Mesabi Nugget. These novel processes are coal based and can use iron ore concentrates or recycled steel plant oxides. The blast furnace processes can use conventional feed materials: pellets, sinter, lump ore and coke. However, DRI and HBI processes are predominantly pellet based but require DR grade pellets that are low enough in acidic gangue (SiO2 and Al2O3) to avoid additional expense in the EAF process This paper will focus on the quality and availability of DR grade pellets for NAFTA DRI/HBI plants but also concentrates for fines based processes and feed materials for merchant pig iron production. INTRODUCTION This paper will outline alternative (to the blast furnace) competitive ironmaking processes and process routes. Within each section the types of iron ore to be utilized will be discussed. Before discussing some of the details of these processes, it may be appropriate to review some definitions and commonly used terms within this industry. DefinitionsDirect Reduction: Reduce iron oxide to metallic iron without melting. Unreduced ore compounds remain as undesirable oxides • Direct Reduced Iron: Iron oxide feedstock exits in same form as entered (pellets in, pellets out; lumps in, lumps out) • Hot Briquetted Iron: DRI that has been hot (1200°F, 650°C) briquetted to a high density pillow shaped briquette • Hot Metal: Molten iron in liquid form, above 2500°F, 1370°C • Pig Iron: Solid product of the iron blast furnace • Residuals: Undesirable elements such as copper, nickel, chromium, tin, sulfur, molybdenum and phosphorus • Gangue: Rock minerals in the iron ore such as silica (SiO2), alumina (A2O3), calcia (CaO), magnesia (MgO). These remain in the oxide form in DR processes. • Reduction: Fe2O3 + 3 CO = 2 Fe + 3CO2 2 Fe2O3 + 3 H2 = 2 Fe + 3H2O (Fe2O3 > Fe3O4 > FeO > Fe)"

Jan 1, 2018

By P. James

"INTRODUCTION Dissolved salts build up in leach solutions over time as leach solutions mature. Iron can be particularly problematic for hydrometallurgical copper production as it can compete with copper for separation during solvent extraction (SX), leading to iron bleed through and reduced electrowinning (EW) efficiency. In its ferric form (Fe+3) it precipitates as a hydroxide at fairly low pH and can promote clogging and disrupted flow within leach pads as a result of localized pH deviations – such as might result from weather events. The solids formed can cause relatively irreversible degradation to pad productivity. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. Control of ferric (Fe+3) levels could be used to lower ferric (Fe+3) levels and keep the ferric hydroxide [Fe(OH)3] precipitation pH sufficiently high to avoid the associated solids formation and potential leach pad occlusion. Control of ferric (Fe+3) and ferrous (Fe+2) tenors and ratios may also provide benefit for improving sulfide ore leaching or bioleaching performance and effectiveness. Traditionally options for such control were rather limited with bleeding contaminants off or chemical dosing treatments being prominent methods. Now Blue Planet Strategies introduces a new option. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DeMet™ (Dynamic Electrolytic Metal Effluent Treatment) platform is highly effective at efficient low-cost conversion and control of iron content in leach streams in addition to targeted dilute metal recovery.[1-6] This powerful new capability provides a new treatment opportunity to control leach solution ferric (Fe+3) and ferrous (Fe+2) tenors to enhance leach operation production."

Jan 1, 2015

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By N/A

finally, but not least, the staff of Vaal Reefs Chemical Laboratory for their assistance and patience with the introduction of a new technology,

Jan 1, 1991

By Samuel S. M. Chan

Rock surrounding mine openings frequently is an impermeable type such as shale or granite. Most rock, however, has joints, bedding planes, cleavage planes, or other potential discontinuities. Permeability to fluids (gas or liquid) may exist via natural joints or fractures in an otherwise impermeable rock. In the mining situation, tectonic and induced tensile and shear stresses may be great enough to cause joints to open or fractures to develop in previously solid rock. The rock, as a result, becomes less self-supporting and may - require artificial support such as rock bolts or timber. Simultaneously, as fractures develop, permeable paths may be created. If fluid can be injected into a previously solid and impermeable rock mass, a logical conclusion is that a fracture (crack) flow path must be transmitting that fluid. The U.S. Bureau of Mines Laramie (Wyo) Energy Research Center has been evaluating results of in-situ oil shale fracturing (hydraulic or explosive) and retorting experiments by. a fluid (air) injection , and borehole air flow profile logging technique since 1956 (1, 14, 15). In the oil shale case, it is imperative to know the location and flow capacity (permeability) of natural fractures, if they exist, and induced fractures that inter-connect vertical wellbores at depths of fifty to several hundred feet. By injecting air into one wellbore in a system of several wells and measuring input volume and pressure while simultaneously measuring the output of other wellbores, the minimum areal extent of interconnecting permeable fractures can be determined. Exact locations (depths) of fractures and individual fracture flow capacities between wellbores can be determined by air flow profile logging (14, 15). Knowledge of fracture locations and permeability is essential to rational experimental in-situ retorting design.

Jan 1, 1973

By Orville L. Lantto, Bruce K. Cantrell, Keith S. Olson

Approximately 10 to 20 pct of exhaust aerosol mass from diesel equipped vehicles operating without exhaust controls is attributable to particles in the 1.0-10 µm size range. Recent in-mine measurements suggest that, in addition to reducing overall exhaust aerosol mass concentrations, the use of waterbath exhaust conditioners (water scrubbers) may significantly reduce the concentration of diesel exhaust particles larger than approximately 0.5 µm aerodynamic diameter. This implies that a measurement system that discriminates between diesel and mineral dust aerosols on the basis of aerosol size would have different accuracies depending on use of a water scrubber. To test this hypothesis, laboratory measurements were made by the Bureau of Mines to determine diesel exhaust aerosol penetration efficiency through a water scrubber as a function of size and engine operating conditions. Size distributions were determined using a Micro-Orifice, Uniform Deposit Impactor. Concentrations of CO, CO2, NO x, O2 and gas-phase hydrocarbon concentrations were also measured. No significant effect was found for these gases other than a slight decrease in NOx emissions. The water scrubber served as a moderate aerosol control with reductions in mass concentrations of about 29±9 pct under most conditions. This reduction occurred for particles less than 0.2 µm and greater than 0.6 µm aerodynamic diameter. Coal dust aerosols are mostly larger than 0.8 µm aerodynamic diameter. With use of a water scrubber, separating the aerosol into two parts, greater and less than about 0.8 µm aerodynamic diameter during sampling, results in collection of diesel and coal dust aerosol accurate to within 10 pct. Without a water scrubber in operation, such a sampling protocol would only be accurate to approximately 15 pct.

Jan 1, 1991

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200', very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 ' ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. As part of the mining process, Coteau removes and replaces thin layers of suitable plant growth material (SPGM) generally ranging in thickness between one and five feet. Historically, tractor-scrapers completed this work; however, rising tractor-scraper costs and increasing haulage distances sent Coteau in search of a lower cost method resulting in the acquisition of a backhoe/truck fleet in 1995.

Jan 1, 1997

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By A. E. Ketler

Optical smoke monitoring fills an important gap in ventilation and fire safety: namely monitoring of smoky, low temperature fires where little CO and heat are generated. Smoke monitoring also avoids the nuisance alarms due to diesel exhaust, battery chargers, blasting and welding. The smoke optical density (OD) fire alarm standard specified by MSHA presents an opportunity for improved safety. Experience of actual mine usage of the SmokeBoss*100 is reviewed, with particular regard to effectivity, maintenance and cost.

Jan 1, 1995

By R. D. Shackleton

Medusa Cement Company, a division of Medusa Corporation, is a medium-sized cement manufacturer serving the midwest, east, and southeast. Medusa's eight plants are located in Georgia, Pennsylvania, Ohio, Illinois, Michigan, Wisconsin, and Canada. Of these, six have active limestone, shale, clay, and sand quarries now in operation. This paper deals with the various individual state laws regulating mining and reclamation at the Georgia, Illinois, and Pennsylvania quarries. Several recommendations for future state mining laws are discussed also.

Jan 1, 1974

By John S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7m diameter primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1984

By Karl C. Dean

To assist in the reduction of environmental degradation resulting from milling operations, the Bureau of Mines has developed, and successfully demonstrated, chemical, vegetative, and combined chemical-vegetative procedures for stabilizing milling wastes under varying environmental conditions. Costs of achieving reclamation using these stabilization procedures are compared with those of other physical and vegetative approaches. The Bureau's chemical-vegetative procedure for establishing vegetation directly on fine-sized wastes compares favorably with other stabilization processes that have been used.

Jan 1, 1972

By C. J. Lewis

Commercial lime plants in the United States and Canada are depicted in Figure 1. The sources of lime available to Nevada and bordering states are rather few. Chemstar Lime has plants at Apex, Nevada and Nelsen, Arizona. Continental Lime, Inc. has plants at Tacoma, Washington, Townsend, Montana and Delta, Utah. However, Continental Lime has a new rotary kiln installation underway near Wendover, Nevada. This plant is scheduled to come on stream in the fall of 1989.

Jan 1, 1989

By Benjamin K. Pocock

When considering alternative equipment choices in mill or process flowsheets, it is important to determine both capital and operating costs of such equipment as well as other possible savings related to downstream operations. This paper presents a few case studies and shows cursory guidelines for the selection of equipment for new installations or in the retrofitting of existing plants. Based upon recent plant experience, suggestions are given to improve the operation of clarifiers, thickeners and vacuum filters.

Jan 1, 1986

By W. F. Visser

The growing availability of information and data analysis capabilities provides new opportunities for improving the performance of operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits the rapid evaluation of changes and fast business improvement decisions. This paper presents a blueprint for system alignment, organizational design and management practices to leverage these developments in performance-driven operations management in mining and mineral processing.

Precious metals exploration is increasingly involved with concealed, deeper-seated gold-silver deposits which exhibit considerably more challenges to the geologist than near-surface, oxidized ores. Thus, cost-efficient, rapid and more detailed target selection and definition will be crucial for gold-silver exploration in the 1990s (Kral, 1990; Woodall, 1992). Although new developments in geophysical and geochemical exploration techniques have made significant contributions, the powerful capabilities offered by alteration mineralogy continue to remain untapped in many cases

Jan 1, 1993

By B. V. Knelson

Although the concept of centrifugal recovery has been around in one form or another for many years, it has not been until recent times that it has became clearly understood am properly put into perspective. Simplistic in theory, it is when one begins to examine the variables involved that the true complexities of this matter begin to emerge. In creating an enhanced g force concentrator, there are many aspects both positive and negative that are encountered.

Jan 1, 1989

By Lancelot E. Kun

The high-rate floc blanket clarification process developed by the Anglo American Corporation of South Africa is capable of continuously clarifying gold and uranium pregnant solutions containing 200-2500 mg/L suspended solids to below 25 mg/L solids at an average rising velocity of 8 m/h at the low process cost of R0,001-0,002 per ton of liquid treated. Overall process cost savings are mainly due to increased polishing filtration cycle times.

Jan 1, 1984