Search Documents

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By S. Klein, M. McLeod, K. Johnson

The East Bay Municipal Utility District (EBMUD) delivers water to the San Francisco Bay Area through an aqueduct system extending from the Sierra Nevada Mountains to the East Bay. This aqueduct system, the Mokelumne Aqueducts, are comprised of three 82-mile long steel pipelines. The portion of the aqueducts crossing the Sacramento-San Joaquin River Delta is recognized to be vulnerable to seismic and flooding hazards. Previous studies evaluated alternatives for mitigating these hazards and increasing the reliability of the aqueducts for the next 100 years. The preferred solution involves construction of a 16.5-mile tunnel across the Delta and re-routing the existing aqueducts through this tunnel

Dec 1, 2022

By H. E. Grand

The purpose of this paper is to outline briefly some basic principles of ground- water hydrology that have application in mine hydrology. The development of a mine below the water table pleads for accurate values to answers of hydrology problems. Such problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by isotropic rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where isotropic rocks are not present. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground water used by -hydrologists in the study of behavior of wells should be helpful to mine operators, The work of the Ground Water Branch of the U.S. Geological Survey through its history has been confined largely to the study of ground water as a resource, In view of the increasing number of problems relating to drainage of mines, the Branch started an investigation of mine hydrology in 1945 under the direction of W.T. Stuart, Mr. Stuart and other workers are making detailed studies of specific mine areas. In the present paper an attempt is made to synthesize some facts about ground water into usable form for the typical mine operator. Mining operations that extend below the water table disturb the natural hydrologic regimen, Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine. The behavior of the cone of depression, as it tends to deepen and increase in areal extent when the mine deepens, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised.

Jan 1, 1958

By Chi M. Phan, Anh V. Nguyen, Geoffrey M. Evans, Graeme J. Jameson

Surfactants are used to control the interfacial properties of the gas-liquid and liquid-solid inter- faces inflotation. This paper investigates the dynamic adsorption of surfactants at the gas-liquid intelface. The dynamic adsorption process was modeled by considering the surfactant mass transfer to the gas-liquid interface by dimion and the Langmuir and Frumkin adsorption isotherms. The numerical computation was applied to solve the non-linear governing equations. The dynamic adsorption was measured in tenns of the dynamic surface tension using the pen- dant drop method. The theoretical modek were compared against the experimental data obtained with non-ionic (Dowfroth 250) and ionic (sodium dodecylbenzene sulfate, SDBS) surfactants. The theoretical results agreed well with the erperimental data for SDBS, but not for Dowfrother 250, especially for the initial stage. Reasons for the variation in results are given in the paper.

Jan 1, 2005

By Leon Y. Sadler

Equations which predict the unsteady-state response of the continuous froth flotation cell to changes in operating conditions are necessary for the rational design of an automatic flotation cell control system. Unfortunately application of automatic control to froth flotation separation equipment has lagged behind application to other types of separation equipment (for example distillation columns, absorbers, liquid-liquid extractors, etc). This may be due partly to the unavailability of suitable mathematical models for predicting the dynamics of continuous mechanical froth flotation cell. This paper presents the results of a comparison of four dynamic flotation models (in transfer function form) using the same set of unsteady-state continuous flotation data. One of the transfer functions tested has been presented previously in the literature (1), another (2) has been accepted for publication, and two are given here for the first time. In addition, data are presented which confirm earlier findings that the mixing in the rotor-stator type cell is nearly perfect. The specific purposes of this paper are to: (1) provide the automatic control systems designer with several alternative dynamic mathematical models of the continuous mechanical froth flotation cell (2) give some idea of the relative a¬bility of each model to predict unsteady-state behavior by fitting each model to the same set of experimental stimulus-response flotation data and (3) provide more insight into the macro-mechanisms prevailing in the continuous mechanical flotation cell. The dynamic models which are presented and tested here all relate the time variation of the concentration of a given floatable mineral in the tailings to a time-dependent disturbance in the same floatable mineral concentration in the feed to the flotation cell.

Jan 1, 1972

By M. D. McInnis

The Jualin Gold Prospect is centered on Johnson Creek, approximately 40 air miles north-west of Juneau, Alaska. The property is on the southern end of the Kakuhan Range with Berners Bay immediately to the south and Lynn Canal to the west. The property is accessible directly by helicopter from Juneau or by float plane to the head of a 5.5 mile gravel road that begins on the north side of Berners Bay and terminates at the old workings of the Jualin Mine near the center of the property.

Jan 1, 1989

By William F. White

It is a pleasure to have the opportunity of being here today to discuss the application of horizontal filters in the metallurgical industries. The use of horizontal type filters has been limited in metallurgical plants. However, in the recent past there have been new designs of this type equipment which greatly broaden their field of application. Through their use in many applications, important economies can be achieved over more conventional methods. The first of the modern continuous horizontal filters was initially developed by Oliver United Filters as their scroll type horizontal filter. This was an outgrowth of the old Oliver Sand Table that was limited to very coarse, free filtering pulps containing no appreciable amount of fine particles. The sand table was rather limited in application. The later continuous scroll type horizontal filter provided for a reverse air blow after discharge which reslurried the heel remaining and permitted the filtration of pulps containing finer particles. In the manufacture of phosphoric acid by the ?wet? process, the filtration of gypsum from the strong acid presented an extremely difficult filtration problem due to blinding of the filter media caused by crystallization of the soluble salts contained in the acid. A filter which allowed for continuous cloth washing was required, and this led to the development of the continuous pan type, and travelling belt type horizontal filters which provided for this need. Among the filters developed were the Prayon by Engineering and Industrial Corporation of Luxembomg for use in their phosphoric acid plants. They are one of the largest manufacturers of phosphoric acid in Europe. The Dorr-Oliver Traveling Pan Filter was also developed by Mario Giorgini, Manager of Dorr-Oliver?s Italian subsidiary, for use with the Dorr Company?s phosphoric acid process. Basically, there are four existing types of horizontal filters in commercial use at this time: The scroll discharge non-pan type, the continuous belt type (Lurgi), rotary pan type, and the traveling belt type. The construction and principle of operation of these various filters will be discussed.

Jan 1, 1958

By Sam H. Patterson

This paper is concerned primarily with the kaolin deposits extending northwestward from Macon, Ga., which is in the western part of the Irwinton district (fig. 1). These deposits are in a belt of kaolin districts extending along the inner edge of the Coastal Plain from the Aiken district, S. C., southwestward to the vicinity of Macon, a distance of 150 miles (250 km). Large kaolin deposits associated with bauxite also occur in an extension of this belt southwestward from Macon as far as the Eufaula district, Ala., a distance of about 130 miles (208 km). The belt splits away from the inner edge of the Coastal Plain in a southwesterly direction from Macon; the Eufaula district is approximately 50 miles (80 km) south of the contact of Coastal Plain sedimentary rocks with much older crystalline rocks. Structure The strata of Cretaceous and Tertiary age containing the kaolin deposits all dip gently seaward irom the landward edge of the sedimentary rocks. The dip of the Cretaceous strata is about 25 feet per mile (4.9 m per km). The dip of Tertiary strata is about 15 feet per mile (2.1 m per km). In places, the Tertiary strata overlap the older sedimentary beds and rest directly on the crystalline rocks. Faults having a few feet of displacement have been observed in several mines, but no major faulting is known in the area.

Jan 1, 1977

By G. Reed Marchant

During the past two decades, we have witnessed the computer revolution. Like other revolutions, it has been successful in many ways; however, it has not been without difficulties. One of the areas where these difficulties have been more prevalent has been in the application of computers for the purpose of controlling industrial processes. During the early 1960's, many people naively assumed that bridging the gap between data processing and process control was a simple matter of connecting a few wires, doing a little programming, laying off most of the people and watching the plant make great increases in production as the lights on the computer blinked on and off. Unfortunately, it has not been that simple. Instead, a whole new-set of disciplines has been required to overcome the major obstacles that exist. Nevertheless, current successes are proving that the digital process control computer is here to stay, and that through the application of digital computers an attractive return on investment can be obtained in many applications.. The purpose of this paper is to illustrate some of the requirements for successful implementation of computer control systems, with particular attention to the following four objectives: First: Acquaint the reader with the general control problems so that he may more fully recognize the major requirements for successful implementation. Second: To acquaint the reader with the types of control hardware that can be considered for use in the development of control systems. Third: To discuss some of the major obstacles that must be overcome for successful implementation of computer control systems. Fourth: To discuss the systems approach in the development of control systems and to illustrate it in the implementation of an actual control system.

Jan 1, 1971

By Eckart Schneider

PROJECT The Walgautunnel is the heart of a new hydro scheme in Western Austria, which is supposed to go into operation in 1984. With it's length of 21,4 km, a bored diameter of 6,25 m and an internal operating pressure of 13,5 bar it will be the largest water conducting tunnel in Austria. Even compared with some of the country's world-famous highway tunnels like 'Tauern' or 'Arlberg' it has to be regarded as a major tunneling project. Owner is the Vorarlberger Illwerke AG, a power corpo¬ration founded in 1924. In the course of the past 6o years this company developed the 'Werksgruppe Obere Ill - Lünersee', consisting of 6 major power plants and 4 large reservoirs. The installed capacity is 1.114 MW in the generating and 529 MW in the pumping mode. The total power output amounts to 1.916 GWh. The water for power generation comes from the glaciers of the Silvrettagroup, as this corner of the Austrian Alps between Vorarlberg , Tyrol and Switzerland is called. The Walgauwerk utilises all the water accumulated by the existing schemes as well as the so far unused run-off water, passing by in the river Ill. The intake to the Walgau-Tunnel is situated right beside the lower reservoir of the recently completed pump-storage plant 'Rodund II' at an elevation of 64o m above sea level. Though the head is a mere 162 m, 1 billion m3 of water will generate 356 GWh per annum. The power-output of the two Francis turbines is 86 MW.

Jan 1, 1983

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022

By V Leus, J. Kallioinen

The large size of the modern flotation cells and the high product flow rate from them has increased the importance of optimal flotation of all the particle sizes and of process control. By treating all the subprocesses of flotation separately a new family of flotation cells and a new concept of optimizing the flotation of coarse and fine particles in separate units but in the same row of flotation cells has been developed. The paper discusses the possibility to enhance coarse particle flotation by varying the froth residence time. A function has been developed between the residence time of the froth, air rate and the froth removal rate of coarse apatite particles. The response of apatite flotation to different control variables has been studied and modelled. The results show that the BPL assay response depends not only on the control variable used but also on the feed assay to the cell. There exists an feed assay dependent region within which the froth assay can be controlled by using the froth residence time as the control variable. These regions can be used to tune a rougher-multistep cleaner circuit to optimal.

Jan 1, 1993

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975

By J. F. McDonald

On December 8th of last year, the new St. Clair River tunnel was holed-through to Port Huron, Michigan. The tunnel, commissioned by the Canadian National Railway, was needed to replace an existing tunnel that had been built between 1889 and 1890, and had remained in continuous operation until the new tunnel was opened to traffic in April of this year. The original tunnel, after more than 100 years of service, was still structurally sound, but was too small to accommodate the double stacked container cars and other advances in the railroad's equipment that had developed over the years. Prior to the construction of the first tunnel, all freight was barged across the river. It was a slow, expensive process, which in winter was sometimes impossible. The nineteenth century tunnel was built in twenty months, utilizing two shields that mined to the middle from each end. The lining, which is still in excellent condition, consisted of bolted, cast iron segments, with an O.D. of 6.4 meters. It was the first sub-aqueous tunnel built in North American, and it's use of compressed air under the river and hydraulic power on the shields may also have been firsts. The digging was done by hand, and the muck hauled out by mule drawn wagons. Boulders and methane gas were reported to be a constant problem during the drive, and compressed air sickness was common, but when the two shields came together in August of 1890, it was reported that the alignment was within 6 mm. The new St. Clair River Tunnel was constructed for basically the same reason as the original. The larger equipment which the railroad is using today would not fit through the old tunnel, and once more they were forced to ferry the cars across the river.

Jan 1, 1995

By A. R. Hollbach

This paper presents a succinct overview of the Canadian coal situation. The topics treated specifically are: the rates of growth of coal supply and demand; the relationship between the coal and electricity generation industries which form its dominant market; the unique impact of nuclear generation on coal demand in Canada; and finally, a view of the developing technologies which will create opportunities for growth in the coal industry of the future. Resources The most important element of coal supply is the resource. The disposition of Canada's coal resources has a marked effect on their utilization, since industry in Canada has not generally developed around coal-fields. The distance from the major industrial centres of Ontario and Quebec to the major region of coal supply in Alberta and British Columbia has crested an economic barrier to the expansion of the use of domestic coal.

Jan 1, 1985

By W Medina, G Angulo, A Anani

A current challenge faced by the mining industry is solving the integrated transition mine problem (TMP) that maximizes the net present value (NPV). This study aims to develop an optimization framework capable of solving the TMP. The problem is NP-hard and therefore computationally intractable. Three ad hoc approaches – Exact solution, Benders’ decomposition, and Benders’ decomposition with Bienstock-Zuckerberg (BZ) algorithm – are compared for different scheduling periods. The TMP is formulated as a mixed integer linear programming model, implemented in Python, and solved with the Gurobi optimizer. The results showed that Bender's decomposition with the BZ algorithm outperforms the other approaches in execution time, computational cost, and feasibility to address large problems in exchange for a marginal cost in the quality of the NPV obtained. In addition, the probability of finding the optimal point of transition is higher regardless of the number of feasible crown pillar locations evaluated. This is achieved through the optimality cuts proposed in the algorithm.

Jun 25, 2023

The Northside Storage Tunnel Project in Sydney includes over 20 km of TBM driven tunnels, over three km of declines and major caverns and pump rooms. The paper describes methods used for design on the project. Emphasis is given to the refinement of the use of empirical rock mass classifications, and to the use of discontinuum numerical methods. The use of empirical rock mass classifications in Sydney sandstone has usually led to conservative design because the systems are based on a random orientation of joints in the rockmass. Because the joint sets are usually oriented in a way that is beneficial for tunnelling, limits must be placed on the parameters used in the classifications system. The paper discusses these limits and the derivation of the parameters. The use of numerical methods in Sydney sandstone is discussed. Continuum methods have their uses, but discontinuum methods are preferred. The use of UDEC has been validated against a previous project, the New Southern Railway. Recommendations are given for UDEC models. In Sydney's geology, so advantageous for tunnelling, the challenges of this project have been to make the best use of the good conditions, while maintaining safety for the workforce and the future operators of the project.

Jan 1, 1999

By P. Mousset-Jones

The USBH Mining Systems and Ground Control Generic Research Center funded a project leading to the improved planning of airflow and refrigeration in underground mines experiencing hot working conditions. The project was broken down into approximately five phases: 1. Visiting some of the known hot mines in the U.S. and sending out a questionnaire to determine other mines which might be experiencing hot working conditions in the future. 2. Choosing two mines in which to conduct measurements to determine the insitu rock thermal conductivity and diffusivity, and comparing these values with laboratory determined values. 3. Investigating computer programs available for mine climate simulation, and testing these programs with case study examples from the two mines where the rock thermal properties were measured. 4. Considering improved ways of estimating the wetness factor and experimenting with the use of heat flux meters to more directly measure the rock heat inflow into the airstream. 5. Applying the results of these investigations to simulating the climate for future mine development and production areas at the two- mines. The project is approximately two thirds completed. At the time of writing, the insitu measurements at one of the mines are still being recorded. This paper will be describing the procedures and results of the insitu rock thermal property measurements, and give a brief description of some of the simulated results obtained for a mechanised cut and fill stope case study from the Homestake Gold Hine in South Dakota.

Jan 1, 1985

By J. C. Bradbury

The Illinois State Geological Survey's program in industrial minerals is twofold-the gathering of information on mineral raw materials and the generation of data on the use of these materials. The first function is carried out by the Industrial Minerals Section and the Clay Resources and Clay Mineral Technology Section of the Geological Group, and the second is the responsibility of the Chemical Engineering Section of the Chemical Group. Gathering in formation on raw materials includes both mapping of resources and fundamental geological research. Recent and current research projects include studies relating lithologies of limestones to their physical properties, investigation of sulfur dioxide reactivity of various types of limestone, lithostratigraphic studies of limestones of Mississippian age, investigations of heavy minerals in Cretaceous, Tertiary, and Pleistocene sands, studies of the environments of clay deposition, electron microscope studies of clays and limestones, and investigation of long-term expansion in ceramic products. A relatively recent development that relates more to dissemination of information than to research is environmental geology. This affects the Survey's industrial minerals program chiefly by stimulating the study of rock and mineral resources in metropolitan areas and reporting the results for the land- use planner as well as the engineer or mineral producer. The Survey's program of research on the use of industrial minerals was expanded and diversified in 1966. Incorporating a minerals beneficiation lab, the program is designed to develop new uses for existing mineral resources and to assist producers in implementing these ideas: Projects of the minerals engineering program have included the separation of a feldspar concentrate from certain glacial outwash and river sands, recovery of kaolinite from the waste from silica sand operations, development of the use of an Illinois clay as a binder for pellets, and investigations into the use of fly ash and fluorspar mine tailings.

Jan 1, 1970

By R. J. Smith

Tar sand deposits in Utah represent more than 25 billion barrels of in-place bitumen, 96% of the known U.S. reserves. The technological development of a hot water processing strategy for the Canadian tar sands and the commercial Production of synthetic crude oil from this natural resource suggest that similar success may be possible for the utilization of Utah tar sands to provide our country with a new domestic source of synthetic crude oil. In this regard an active research program to develop a hot water processing strategy for Utah tar sands has been sustained at the University of Utah for the past five years. The hot water process for Utah tar sands differs significantly from that used for Canadian, tar sands due to the inherent differences in the respective bitumen viscosities and the nature of the bitumen-sand association. These differences have led to the identification of certain design criteria necessary to achieve satisfactory phase disengagement during digestion. (8,9) Subsequent flotation of the digested tar sand is a subject of current attention and is considered in this contribution for the Asphalt Ridge tar sand deposit. Although contact angle measurements of pure Asphalt Ridge bitumen indicate moderate hydrophobicity, air bubble attachment to the bitumen concentrate taken from a 37 liter flotation cell is not possible. This surprising result suggests that the flotation separation is dependent on air bubble entrapment rather than on attachment due to surface hydrophobicity. The occlusion of air bubbles in the bitumen is apparent from visual examination of the concentrate, especially at lower temperatures. It seems that a bitumen bubble agglomerate forms in the impeller region of the flotation cell, the effective density of which is such to allow the agglomerate to float to the surface. A factorial design of the major operating variables in the flotation separation indicated that the quality of separation was significantly dependent on the flotation temperature and to a lesser extent on the degree of agitation. For a flotation temperature of 77C recovery of 96.7 percent was realized at a grade of 61.0 percent bitumen. The improved separation at higher flotation temperatures was found to be due to the decrease in bitumen viscosity resulting in more effective rejection of coarse sand from the concentrate.

Jan 1, 1980