Search Documents

By D. B. Ogbenlowo

A major problem facing the Nigerian Mineral Industry today is flooding in its underground mines. Flooding has reduced productivity to a very low level which results in huge economic losses. Consequently, this paper presents a computer based model that pre¬dicts the quantity of water accumulating from diverse sources in an underground coal mine with a view to suggesting a permanent solution to the problem. Specifically, the paper describes the model building technique and the output achieved from its application to a real mine case study.

Jan 1, 1988

By C. Bazin

The separation of rare earth elements is a complex process that is industrially carried out using liquid/liquid extraction. Detailed flow sheets of solvent extraction plants for the separation of rare earth elements are rarely available in the literature which limits the opportunity to teach and test the application of data reconciliation, process optimization and control to these types of plants. The basis of a simulator for a rare earth elements separation plant is described in this paper. The simulator is used to adjust the organic phase and stripping acid flow rate in a separation circuit of heavy rare earth elements from light one?s.

Feb 27, 2013

By D. L. Ealy

At the Beckley Mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by using a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1980

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By R. R. Klimpel

The process of froth flotation as a means of upgrading the quality of coal by removing ash/pyrite and of separating selected mineral(s) from undesired gangue materials is certainly one of the most common unit engineering operations in use today. Flotation has been successfully practiced at the industrial scale for well over 50 years, and if anything, its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation, as a process, has also shown itself to be an extremely flexible process that lends itself well to a wide variety of solid/solid separations. Thus separations can involve very different particle sizes, particle densities, relative weight ratios of materials to be separated, etc., with surprisingly little modification in equipment and operating philosophy required.

Jan 1, 1988

By L. R. Stoiser

The mineral resource potential of the Los Bronces deposit was successfully evaluated by an intense, coordinated field program over a 37-month period (April 1978 - May 1981). This project was part of a much larger study to determine the economic feasibility of expanding the open-pit, mine-mill operation 10-fold to 80 kt/d (88,000 stpd). The resource project included more than 120 km (74 miles) of core drilling and 64 km (40 miles) of drill rig access way construction under adverse topographic and climatic conditions, detailed geological mapping, and other related activities. The Los Bronces deposit is composed of an earlier mineralized porphyry-type body intruded in part by a large complex of mineralized hydrothermal breccia pipes. The mineralization is hosted by intrusive and extrusive igneous rocks. Various stages of erosion, oxidation, leaching, and supergene enrichment of copper are present. Drill hole indicated geologic reserves are estimated at 1.3 Gt (1.4 billion st), averaging 0.81% copper and 0.016% molybdenum at a cutoff grade of 0.6% copper equivalence decreasing to 0.25% over the life of the mine. Trace amounts of silver are also present.

Jan 1, 1987

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By Chin Wei Yang

Linear programming (LP) has proven to be a most effective mechanism for modeling a vast array of practical problems, while the development of LP applications in engineering have been extensive enough to show its advantages and limitations. In this paper: we focus on the properties of the widely-wed linear programming transportation (LPT) model formulated and developed by Koopmans (1) . There have been many models of this type applied especially in the field of energy economics (2-7). Since most of these applications can be linked to the seminal work of Henderson (8), we stall present our discussions based on his work.

Jan 1, 1980

By Edgar W. Sawyer

Attapulgite and sepiolite are the clay minerals used to thicken ionically contaminated watzrs in the preparation of drilling fluids. They are nonsweliing clays that can be dispersed and reflocculated by mechanical means to increase the viscosity of fresh water and salt and gypsum contaminated waters. Those gelled in fresh water do not become excessively thick when contaminated with high salt concentrations or polyvalent cations encountered during drilling. Gels formed exhibit thixotropy and yield pseudoplastic rheological behavior due to the particle interactions and mechanical interferences of the flocculated gel structure.

Jan 1, 1983

This paper provides a summary on the use of the POL YCOM high pressure grinding roll (HPGR) for increasing extraction in copper leaching. The energy-efficiency and significant hydrometa1lurgical benefits of the HPGR result in better acid-curing, higher solution application rates, improved copper extraction from various copper minerals and better recovery from high acid consuming ores. The HPGR's metallurgical features such as micro-fracturing, better liberation of disseminated and veinlet copper, increased oxygen and lixiviant penetration lead to higher copper extractions than achieved by conventional crushing. Flowsheet options, operational characteristics and applications for various copper ores are outlined.

Jan 1, 1996

By Robert A. Cummings

Disintegration of the immediate shale roof in coal mines interferes with ventilation, production, and safety. The effect is seasonal and correlates with high levels of moisture in the intake ventilation air. Disintegration, though not completely understood, is caused by shale dilation and weakening upon exposure to atmospheric moisture. Fluctuating moisture conditions are particularly deleterious, and may be at least partially controlled by "tempering" the air before it is brought to the working places. Roof behavior was studied in an operating mine during a 12-month monitoring period. This approach can be used in developing criteria to reduce or prevent shale roof deterioration.

Jan 1, 1981

By D. J. Murdock, Wyslouzil, I. M. Flint

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low-acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favored for this service because of low capital and operating costs and improved metallurgical performance compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1995

By B. A. Barnum

The Chino mine is an open pit copper mine located in southwestern New Mexico, at an elevation of 1890 m (6200 feet) above sea level, approximately 117 km (70 miles) north of the Mexican border. It is owned by Chino Mines Co., a Phelps Dodge Corporation-Mitsubishi Minerals partnership, and is operated by Phelps Dodge Corporation. As part of an effort to maximize production and minimize costs, a computerized truck dispatching system was approved for purchase and installation at the Chino mine in March. 1984. Modular Mining Systems, Inc. was commissioned to install their system, trade named DISPATCH. The system installation was completed and operation began in July, 1985. Installation and operation of the system has presented some interesting challenges and problems, which have been overcome, resulting in increased productivity for the haulage truck and shovel fleets.

Jan 1, 1987

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By C. G. Bock

Geologic profiles constructed from exploratory drill holes gave basic geologic information for bidding on 4913 ft. of twin rock tunnels under the Potomac River. To provide additional geologic information for construction, tunnel faces and shafts were mapped throughout excavation. This information was plotted in plan and section so that geologic structure could be projected ahead and prediction of conditions could be made. In structurally complex areas, 3-D models were made and used to show the geologic structure. Core from exploratory drill holes was relogged and structure oriented with that found in the tunnels to make the ultimate use of the core and refine the geologic picture. As excavation proceeded, geologic mapping showed that the projection-prediction approach was useful and essentially correct.

Jan 1, 1974

By C. A. Roberts

What are the benefits and limitations of financial analysis software as a decision making tool in the mining industry? Traditionally, the assumptions and simplifications imposed by complex and uncertain information have been viewed as the main obstacle to reaching an optimum decision. Recently, however, phenomena such as corporate culture and power structure have received increasing attention as significant influences on organizational decision making processes. Studies of these phenomena have suggested an alternative way of understanding decision making processes and an alternative view of the role played by computer analysis in such processes. This paper presents these two views of decision making, and examines what each implies about the role of financial analysis software as a decision making tool in the mining industry.

Jan 1, 1992

By W. A. Rickelton

Trialkylphosphine sulphides, in contrast to their well known oxide analogues (1,2,3,4), have received comparatively little attention as metal extractants and previous studies have been biased toward analytical rather than commercial solvent extraction applications (5,6,7). The sulphides are soft Lewis bases and only from complexes readily with the limited number of metals in the periodic table which can be classified as soft acids (8) e.g. Ag+, Hg2+ and Pd2+. Consequently, these compounds tend to be more selective than the broad-spectrum, hard-base, phosphine oxide extractants such-as TOPO (trioctylphosphine oxide). The purpose of this paper is to describe a potential application of one phosphine sulphide, CYANEX® 471X extractant, in the selective recovery of silver from base metal sulphate solutions. CYANEX 471X is triisobutylphosphine sulphide (TIBPS).

Jan 1, 1984

By R. K. Mehta

An accurate, efficient and stable computation of the mill matrix function (eAt) is needed where mill matrix (A) is a real general matrix. Two important modeling cases in comminution where such need arises are: Heterogeneous comminution behavior of multi-component ores and ultra-fine grinding involving simultaneous attrition and fragmentation breakages. This paper presents the application of a novel splitting method in conjunction With similarity transformation technique in the form of "product formula" which is found to work in all cases and uses a most aggravating, yet interesting property of the matrix exponential in a restricted sense. Results are presented showing that this method can yield solution as accurate as those obtained With an analytical technique. The utility of this computational approach is demonstrated by parameter estimation analysis using a distributed component model in the liberation area through computer simulations.

Jan 1, 1992

By E. A. Barrett, L. L. Rethi

Throughout all segments of the United States mining industry, 163 independent contractor employees were fatally injured between 1990 and 1997. Factors that contributed to these injuries were identified after reviewing descriptive information contained in Mine Safety and Health Administration fatality reports for each of the incidents. Thirty-three unique contributing factors were identified and multiple factors were noted for each fatality. Those most frequently discerned were "failure to follow `standard operating procedures"', (35% of the fatalities), "poor positioning of employee" (26% of the fatalities) and "failure to maintain equipment" (23% of the fatalities). Contributing factors were then associated with the accident and job classifications of the victims. Factors having the highest frequencies in the top five accident classifications where most fatalities occurred were as follows: powered haulage - "failure to maintain equipment"; machinery - "poor positioning of employee"; slip/fall of person - "inadequate fall protection" and "failure to wear safety line"; electrical - "equipment contact with power line"; and falling/rolling/sliding rock - "poor positioning of employee. " Among the job classifications in which most fatalities occurred, leading contributing factors were as follows: truck driver - "failure to follow standard operating procedures" and "poor positioning of employee"; laborer/utility man/pumper - "poor positioning of employee"; mechanic/ repairman and welder - "failure to follow standard operating procedures." Recommendations for utilizing contributing factor information as a basis for safety training are proposed. Training programs may be developed that inform independent contractor employees of factors which, in the past, have contributed to fatal injuries in their job classifications. Then, by combining this information with contributing factors identified in "related" accident classifications, a truly focused training intervention that addresses very specific workplace hazards may he developed.

Jan 1, 2002