Search Documents

By G. Luttrell

Coal preparation plants play an important role in modern society by providing high quality feeds for coal-fired utilities, industrial boilers and metallurgical coke facilities. Unfortunately, field data indicate that preparation plants are often not operated under optimum conditions, resulting in lower productivity and lost profits. In many cases, this shortcoming can be attributed to a failure by plant operators (i) to recognize the importance of correctly adjusting plant operating conditions to accommodate requirements dictated by coal sales agreements within different coal markets and (ii) to properly account for variations in product moisture with particle size across different plant circuits. This paper discusses the important influence of moisture constraints on preparation plant optimization and provides a case study to illustrate the potential gains that can be realized via proper understanding of plant moisture control.

Jan 1, 2009

By Q. J. Browne, M. A. Miller

Silver Bell produces about 22,000T of fine copper annually from low-grade chalcocite and oxidized copper ore that is recovered by sulfuric acid leaching and SX-EW processing. The current mineable reserves are 146 million short tons averaging 0.39% Cu, at a 0.15% cutoff. Silver Bell utilizes two types of mining methods to develop the low-grade reserves: (1) a conventional blast, load and haul method for run-of-mine leach ore, and (2) rubblization of material on the margins of existing pits. Rubble leach ore is blasted, terraced with a bulldozer, and leached in place. Mining and/or rubble leaching is currently active in four separate pits. Laramide-age intrusive rocks host porphyry copper mineralization at Silver Bell. Quartz monzonite porphyry dikes and stocks, mafic-poor equigranular granite (alaskite), and sub-volcanic dacite porphyry are the predominant host rocks. Most of the ore currently mined comes from near-horizontal enrichment zones containing veinlets and disseminated grains of pyrite and chalcopyrite rimmed by chalcocite. Conversion from a milling operation to a leach only operation allowed for a much lower cutoff grade than was historically used at Silver Bell. Mine geologists were able to increase copper resources by drilling exploration targets that were previously interpreted to provide lower-grade mineralization below cutoff-grade for milling. Geologic parameters that effect the distribution of rubble and mineable leach ore include: ore grade and thickness, variable alteration styles in intrusive host rocks that affect fragmentation during blasting, acid consuming carbonate wallrocks (reactive skarn) which influence leach solution pH, solution flow paths and drainage, presence of leachable oxide mineralization in non-reactive skarn, and depth to hypogene mineralization which is currently uneconomic. Geologic parameters are used to predict rubble bench limits, vary blast hole spacing for consistent fragmentation, and correct errors in mineral zone classification based solely on blast hole assays. An expansion-drilling program has identified approximately 150 million tons of new leachable copper resources with an average grade of 0.35% Cu.

Jan 1, 2002

By J. L. Whitlock

A mutant strain of Pseudomonas paucimobilis is utilized to effectively degrade and or remove 90-98% of cyanide, thiocyanate, toxic heavy metals and ammonia from a cyanidation mill process and mine discharge maximum of 21,000 m3/d (5.5 MGD). Homestake Mining Company?s biological wastewater treatment plant has been in full scale operation for over 2 years at the Homestake Mine in Lead, South Dakota.

Jan 1, 1987

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

By F. Mielli

Camera systems and video surveillance are usually associated with people and asset protection. However, they can be applied in a mine environment beyond conventional surveillance: For process monitoring, collision avoidance, sizing, flotation cells, conveying systems, blasting, objects and people tracking, thermal profile, and to automatically identify equipment that is missing parts,. Image and video solutions can be driven by better integration of powerful video analytics and cameras systems in automation tools such as process controllers and supervision systems.

Feb 27, 2013

By J. M. Mutmansky

Introduction Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, numerous developments have taken place in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991). Mesh selection methods A procedure for mine ventilation network solution based on mesh equations typically consists of two steps: • the mesh selection step and • the network solution step. The mesh selection step establishes a set of independent equations to solve the network. The resulting equations are nonlinear. One method of solving nonlinear equations is to linearize the equations and iteratively solve these linear equations. The four analysis methods previously discussed in this paper use this approach. The linear equations required for solution can be written in matrix form as: P•dQ = dF (1) where P is the pseudo-resistance matrix, Q is the quantity matrix, and F is the Jacobian matrix (Kim and Mutmansky, 1991). The efficiency of the solution method depends on the characteristics of the P matrix, which in turn depend on the method of selecting meshes. To understand the impacts of the mesh selection methods on the efficiency of the ventilation network analysis procedures, the characteristics of the P matrix must be understood first. The diagonal elements of the P matrix, m in number, are the sums of the pseudo-resistances of the branches contained in the m meshes necessary for solution. The off-diagonal elements are the sums of the pseudo-resistances of the branches shared by two meshes. For example, P12 (first row, second column element of the P matrix) is the sum of the pseudo-resistances of the branches common to mesh 1 and mesh 2. When solving the system of equations expressed in Eq. (1), three of the iterative procedures (the Newton-Raphson, the linear theory and the second-order approximation methods) use the direct factorization method (Burden and Faires, 1985) on the P matrix. When the direct factorization method is used, the computational efficiency is enhanced by larger diagonal elements and a sparser P matrix. Generally, the sparsity of the P matrix is more important than the size of the diagonal elements. There is no known mathematical method of predicting the efficiency of these procedures, but heuristic methods can be used to study the efficiency. The Hardy Cross algorithm applies the Gauss-Seidel method of splitting the P matrix and applies the Newton-Raphson procedure. The efficiency of the Hardy Cross method depends on the spectral radius of the matrix[[D-L]-1U], where D is the diagonal, L is the lower triangle and U is the upper triangle of the P matrix for the Newton-Raphson method (Ortega, 1972). The smaller the value of the spectral radius, the faster the convergence. As with the other three methods, larger diagonal elements and a sparser matrix aid in faster convergence. With the Hardy Cross method, however, the size of the diagonal elements is more important than the sparsity of the matrix. Remembering that each of the diagonal elements of the P matrix is the sum of the pseudo-resistances of the branches in a mesh and that each off-diagonal element is the sum of the pseudo-resistances of the branches shared by two different meshes, the following strategies can be used: • Avoid having branches with larger resistance values shared by multiple meshes. This increases the size of the diagonal elements and reduces the chance of off-diagonal elements being large.

Jan 1, 1993

By Roland Trunk, Marcel Imbach, Yves Boissonnas, Jan Vesely

"INTRODUCTION The expansion of the Suez Canal, which runs between the Mediterranean and Red Sea, is at the top of Egypt’s economic agenda. The £8 billion development plan includes a new channel alongside the existing one which will double the number of ships able to pass each day and several tunnels to connect the Sinai peninsula to the main part of Egypt. The Egyptian government ordered three new tunnels under the Suez Canal in the area of Port Said as part of the Canal Region Development Plan. The three tunnels will contribute to the North Sinai expansion, helping to create a vast industrial zone and completing the coastal road extension from Rafah to Nuewiba. Two of these three tunnels will be allocated for roads and the third for railway traffic. A further part of the Suez Canal development mega project are an additional six tunnels in the area of Ismailia and Suez. The focus of this paper is on the two road tunnels in Port Said and will give an overview of the project and the challenges encountered regarding the technical complexity and tight time schedule both in its design and execution. PROJECT OVERVIEW The tunnels will be built in the area of Port Said (see Figure 1) which is the most northern part of the Suez Canal.The road alignment connects the Port Fuad Road in the east bank of the Suez Canal to the Port Said-Ismailia highway in the west bank with a dual carriageway section. Each of the carriageways has two lanes. The bored diameter of the 2.8 km long road tunnels is 13.050 m and will be driven with two Mix-Shield TBMs. The distance between the two tunnel axes is planned with 42.5 m (discussion about a reduction are ongoing). The width of the Suez Canal is around 340 m at upper level and around 170 m at the bottom. During the TBM drive, three main geological layers are expected. Below a depth of around 40 m in a very soft clay layer, a dense to silty sand layer is predicted. Within the sand layer another silty hard clay is expected in different depths with variable thickness. After finishing the excavation of the road tunnels, the same TBM will be used for the railway tunnel. The lowest points of the road tunnels will be located 59 m below the surface (tunnel invert to surface) and only 18 m of ground cover exists between the tunnel crown and the Suez Canal invert. Minimum ground cover over the tunnel crown is approximately nine meters at the tunnel portals."

Jan 1, 2016

By B. Mishra, Q. Shi, Y. Zhao, G. Zhao

Shale is anisotropic due to the presence of bedding planes. The anisotropic strength of shale has been extensively studied. However, little attention has been paid to the size effect on shale strength considering the anisotropy. This research uses the discrete element method to study the size effect on the strength of shale under the uniaxial stress state. It is assumed that the anisotropy is caused by bedding planes, while the size effect is caused by randomly distributed flaws. The numerical model of shale comprises three components: shale matrix modeled by bonded particles (2) bedding planes modeled by smooth joints (3) flaws modeled by discrete fractures. The developed model is scaled to different sizes and tested in the uniaxial compression and the direct tension tests. The test result show that the uniaxial compressive strength decreases as the specimen size increases when the loading direction is perpendicular or parallel to bedding planes. The uniaxial compressive strength is determined by the flaws while the bedding planes only play a limited role. However, the size effect on the direct tensile strength depends on the direction of bedding planes. When the loading is perpendicular to bedding planes, the size effect is not prominent. The direct tensile strength is determined by the bedding planes while the flaws have little effect. When the loading direction is parallel to bedding planes, the direct tensile strength decreases when the specimen size increases. The direct tensile strength is determined by the flaws while the bedding planes have little effect.

Mar 2, 2022

By Liming Yuan, A. C. Smith

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, a process which causes the gob to “breathe” out and in. Although the concept of gob “breathing” is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamic (CFD) simulations were conducted to model the spontaneous heating of coal in the longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

The flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

Apr 20, 2021

By Kai Wang, Chao Xu, Qiang Fu, Tong Yang, Chunyu Zhao, Wei Zhao

The stress of a coal seam is an important factor that affects the permeability of the coal seam and then affects the coalbed methane (CBM) drainage. In China, adjacent coal seam mining is an important method to reduce stress, which increases the permeability of the coal seam. However, in the process of mining adjacent coal seams, many coal pillars remain, which causes stress concentrations and results in a decrease in permeability. Therefore, it is important to study the influence of coal pillars on the stress of adjacent layers and its distribution and evolution in the floor rock. This paper took the Shendong Baode Coal Mine as a case study and investigated the influence of the coal pillar on the stress and permeability of coal seam #11. The results show that under a coal pillar, the relationship between the vertical stress of different floor depths and the width of the coal pillar can be divided into a negative correlation zone, transition zone, and positive correlation zone. The change in the coal pillar width does not affect the pressure relief range or the degree of pressure relief in the adjacent coal seams below the goaf. The field measurements show that after the mining of panel #81,505, the permeability coefficient of coal seam #11 under the goaf increased from 0.1434 to 26.3545 m2/( MPa2*d), increasing 182.7 times, and the drainage mixing volume of boreholes #1 and #2 increased from 1.24 to 1.52 m3/ min. While the permeability coefficient of coal seam #11 from 12.5 m in the coal pillar has only increased by 2.6 times, the drainage volume of boreholes #3 and #4 did not change significantly.

Nov 19, 2022

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By Yerkezhan Madenova, Kairat Kalmurzayev

This study intends to demonstrate the engineering application of ground penetrating radar (GPR) that would enable site engineers to prevent the high cost of blind drilling. At the tailing dump located in Zhairem Mining and Processing Plant, the challenge of sheet pile driving is encountered due to the indefinite watertight clay layer deposition depth that serves as a protective layer against groundwater contamination. A numerical model of the soil underlying the tailing dump is built using the existing hole data to compare and confirm the existing geological cross sections for three profile lines along the south and southeast parts of the tailing dump. GPR is employed to investigate the subsoil geological structure and detect the watertight clay layer deposition. On the basis of radargrams tied to the existing borehole data in the numerical model, 21 drill hole locations are suggested to assess and confirm the clay layer depth along profile lines at the tailing dump. The drilling results of the suggested holes confirmed the expected depth of the clay layer. It is concluded that GPR is a practical and economic subsurface mapping method that can prevent the high cost of blind digging of the ground and orient the drilling operations effectively.

Jan 12, 2023

By Günther M. Volkmann

"INTRODUCTION The construction of the BAB 44 motorway between Kassel and Herleshausen (both Germany) is an important part of the trans-European road network. After its completion, the A 44 will permit an efficient connection of the Benelux States in the West and Poland in the East. In the section between Eschenstruth and Hessisch Lichtenau the Hirschhagen Tunnel is constructed with a length of 4.1km. Most sections of the tunnel are situated in weak ground conditions. Hence a combination of face bolts with spiles (short forepoling) or pipe umbrellas (long forepoling) additionally support the tunnel heading on a regular basis This article will focus on the application of a newly developed method to connect the pipe umbrella support, which is mostly installed by conventional drilling machines nowadays. The installation method limits the outer diameter to a maximum of 168mm and a pipe wall thickness of 12.5mm because workers must be able to handle pipes and its drill steel. Typically these pipes are connected with threads that create a weak link in the support system so during the last decade alternative connection systems were developed to overcome this disadvantage. One of these alternative coupling systems is the so called Squeezed Connection, which will be explained in this article followed by a discussion of its advantages and disadvantages regarding technical specifications, construction time, and safety issues. THE HIRSCHHAGEN HIGHWAY TUNNEL The German highway A 44 directs from Aachen through the Ruhrgebiet to Kassel (all Germany) and it is extended to Herleshausen (Germany). The new section connects the A 7 to the A 4 after completion. This upgrades the east-west highway connection starting at the Benelux Union and heading to Poland so it is an important part of the trans-European road network. The newly constructed section has a total length of approximately 63 km and comprises 13 tunnels. All tunnels are constructed as double tube tunnels with 2 lanes and emergency sidewalks on both sides and 14 emergency cross passages. The Tunnel Hirschhagen starts in the north of Eschenstruth and ends near Hessisch Lichtenau (Figure 1). The length of the northern tube is 4,147 m and that one of the southern tube is 4,204 m. So it is the longest tunnel of the A 44 and the second longest highway tunnel in Germany when it is put into operation. On its alignment it crosses underground the Losse valley with the state road 7, the streetcar Kassel-Hessisch Lichtenau and the Losse stream. The cover above crown varies from 10 m to 95m and it is the lowest when crossing the Losse stream."

Jan 1, 2016

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

By Claus Becker

Waterbearing, cohesive or non-cohesive grounds with glacial stone deposits are found very often in Europe. The problem consists of destroying the boulders and supporting the face simultaneously. At the example Grauholztunnel Bern ( outer diameter 11,60 m ) the theoretical attempt of solutions for the big machines is described: destroying of the boulders with roller discs, hydraulical support of the front. The problem of coming out of stones of a certain size from the surrounding matrix will be discussed. Further diminishing to the size that can be handled by pumps is executed by a crusher, situated in the center of the machine. At the same example the theoretical attempt for headings in cohesive soil with stone deposits are shown. Surface structure of the cutting wheel and working chamber as well as controllable current movements are the solution here. The danger of clogging discs and stone crusher has to be encountered by right positioning of the tools and jetting nozzles. At the example Sewer MoosstraBe Salzburg the same problems are discussed for the Mikro-Tunnels. The pipe-jacked sewer lines have outer diameters from 485 and 805 mm. With this method, the stones have to be holed through. The wear of the cutting tools determines the [ ]

Jan 1, 1989

By John Newby, Ulf Gwildis, Fred Marquis

From the Brightwater Conveyance System in Seattle to the Second Narrows Water Supply Tunnel in Vancouver, BC, the design and construction of deep-lying tunnels in the Pacific Northwest often require the incorporation of deep portal shafts. Alluvium overlying marine and glacial deposits combined with the high regional seismicity is the common geologic setting. The latest example illustrating the development of shaft design for this scenario is the 40-m-deep shafts of the Annacis Island Wastewater Treatment Plant New Outfall System. The main components of the shafts include the initial lining, providing the excavation support system to be used for launching and receiving a 5-m-diameter TBM; and the final lining, designed to withstand all static and seismic loads and to remain viable for the intended design life. This paper presents design and construction considerations for these shafts against the background of and lessons learned from past project experiences.

Jun 13, 2021

By R. M. Hernandez

The Bureau of Land Management (BLM) constructed four passive biochemical reactor systems (BCRs) to treat mining influenced water (MIW) in the Bunker Hill Superfund area near Coeur D?Alene, Idaho between 2002 and 2003. Initially, the BCRs operated very effectively. However, in the past couple of years, the zinc removal effectiveness of the four BLM BCRs has declined [1]. The central objective of this study was to characterize the microbial communities and substrate present within the BLM BCRs and to use these factors to propose strategies to promote sustained sulfate reduction levels. Microbial communities were characterized by quantifying total bacteria and sulfate reducing species. Substrate was characterized by quantifying the percent organic, acid soluble organic, acid insoluble organic, and bioavailable material within the BCR. The results suggest the depletion of bioavailable organic substrates is the primary cause of the decline in zinc removal and not the microbial community structure. The ability to assess the amount of bioavailable organic substrate and microbial community is important to the understanding of the sulfate reducing capacity of the BLM BCRs and developing strategies to facilitate performance enhancement of the current BLM BCRs. The characterization of organic substrate and microbial community structure are also important to improving design of future passive treatment systems for mining influenced waters.

Jan 1, 2010

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By D. Hodouin

The optimisation of mineral processing plants requires the evaluation of performance indices such as production rate, product quality, valuable mineral recovery and process efficiency. Decision to change operating conditions or equipment to improve plant performances rely on the significancy of the estimated performance indices. The better is the quality of the estimation, the better is the discrimination capability of the index and as a consequence the larger is the operation improvement. The reliability of performance calculation depends on the sensors nature, accuracy and location, on the data redundancy, on the correction method applied to raw data and finally on the propagation of measurement errors along the calculation of performance indices. To maximize the quality of the data collected for performance evaluation, the following techniques are presented, discussed and illustrated: redundancy and observability analysis, data filtering for mass conservation, variance analysis of performance calculation, and data acquisition strategy design.

Jan 1, 1991