Search Documents

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By Chuang Sun, Feng Luo, Guo‑dong Li, Xue‑qing Li, Tuan He

The mining-induced failure of the coal seam floor is essential for water inrush. The mining disturbance to the floor, especially in the thick coal seam, is severe, and the water inrush risk is also higher than that in regular thick coal seam excavation. The superposition of many stresses, including in situ stress, mining-induced stress, and confined water pressure, must be considered in the prediction of the floor failure depth. This study adopted the elasticity analysis, FLAC3D numerical simulation, and on-site acoustic wave test comprehensively. The thick coal seam working face of the Zhong-Yu coal mine affected by confined water was selected as the engineering background to study the characteristics of the floor failure. Based on elastic foundation theory and the superposition principle, the mechanical model and the failure depth criterion of the floor were established, respectively. The distribution and evolution of mining-induced stress and the plastic zone in surrounding rock during the mining process are obtained by FLAC3D. In addition, the changes in the P-wave wave velocity in the floor before and after mining were compared and studied by the acoustic wave test method. The range of floor damage depth is determined on the basis of the above research.

Jun 8, 2022

By Y. Ye

Induction times for a variety of minerals have been measured at a particle bed. Electrostatic repulsive forces between bubble and particle generally are of secondary importance in determining the hydrophobic state; nevertheless, the shortest induction times are measured at the isoelectric point of the solid. More importantly, the study shows that the film-rupture mechanism at a polished surface might be different from that at a particle bed. The induction time measured at a particle bed, besides being dependent on the surface chemistry of the system, shows a definite relationship to particle size and density. Theoretical analysis suggests that such a measured induction time at a particle bed should properly be defined as an attachment time which consists of the induction time and the film-displacement time. Thus one portion of the measured attachment time is the induction time, the time required to thin the water film between the particle surface and the gas bubble to a critical thickness so that rupture of the film takes place ('1)' The other portion of the measured attachment time is the time required for the film to be displaced to such an extent that the attachment is stabilized with respect to the upward motion of the bubble and the downward gravitational force acting on the particle ('2)' Further, the present study illustrates that '2 is related to the hydrophobic character of the surface, the rate of film displacement after rupture, the upward velocity of the captive bubble, and, most importantly, the particle size and density.

Jan 1, 1988

Horizontal stress is an important factor that contributes to roof failure during a long wall entry development, especially when the immediate roof is weak. In this study, the effects of the three factors, the stress angle between the maximum horizontal stress and entry development, the stress ratio of the maximum to the minimum horizontal stresses, and the sequence of entry development, on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method, when the horizontal stress is fixed. The results have confirmed that the stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the angle is about 60°_75°. The stress ratio has little effect on the roof stresses. In addition, the sequence of entry development has also little effect on the roof stress for the specific case analyzed.

Jan 1, 1999

By X. P. Zheng, H. K. Lin

Barium fluorophlogopites were synthesized in the laboratory to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between the layer structure and the Ba-O bond length. The higher the barium content, the larger the cell volume and distance between the layer structure, and the longer the Ba-0 bond, the more negatively charged the surface is, and, hence, the more easily adsorbed are cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1995

By Hans-Werner Tonscheidt

Introduction The endeavours to mechanise the shaft sinking operations have led to the development of shaft boring using a V-Mole. The method implies competent ground and a pilot hole of sufficient verticality. This connects the top and the bottom of the shaft and serves for air ventilation and the transport of mullock. The shaft boring machine - nick name V-Mole - with a general pattern similar to a tunnel-borer reames the pilot hole to the designed diameter of the shaft. (Figure 1) The excavating of the rock, the removal of the mullock from the face and the lining of the shaft wall are done simultaneously. If they can be done also continuously this than creates a high potential of productivity. The verticality of the shaft can be garanteed due to the laser beam guided steering system. The diameter of the shaft is variable in steps of 0.5 m between 6.0 and 10 m in accordance with the need. It decides the capacity of the V-Mole to be applied. The depth of the shaft does not depend on the machine. It is practically unlimited as long as a suitable pilot hole is available. Up to 1988 almost 12.656 m of shaft have been drilled on 40 individual projects in Germany and the U.S.A. using a V-Mole. The rocks penetrated were Carboniferous sediments consisting of Sandstones, Shales, Conglomerates and Coal seams. The average uniaxial compressive strength was in the range of 300 - 700 Mpa with a maximum of 1700 Mpa in some singular sandstones.

Jan 1, 1991

By J. Perlacia

Introduction The Bulk Handling Technology has already started its transformation to the Industry 4.0. Having some of the harshest working and environmental conditions of the industry, the possibility of remote analysis and maintenance of the components seems a perfect target to focus on. The most important and expensive tools have been adapted to the digital era during last years, from remotely controlled haul trucks to monitored conveyor belts. However, these big parts of the installations rely in smaller parts that have been left aside for a while, mainly due to the difficulty to adapt them to IoT (Internet of Things). The paradigmatic example is the lack of monitored rollers whereas all the other components of the conveyor belt installations (the belt itself, motors, drums etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stop of the whole conveyor, due to the possible damages to the belt, thus the implementation of an integral monitoring system of all the components of the conveyor is a must. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers, facing all the problems until its final installation in very different demanding conveyors, from the Australian extreme heat to the freezing cold Norway. All the tests done under actual working conditions, in real installations, have given a valuable knowledge in the identification of problems, their solution and the final advantages of a roller monitoring system. Background and Current State The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, an unexpected stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers long or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. As in many other industry products, the condition of rollers can be recognized measuring key parameters like the temperature of the bearings, the vibration level etc. The traditional way is to use the characteristic noise of a failing bearing, but this method usually implies to change several rollers because the maintenance team is not able to identify a single source of the noise. In recent years different attempts to measure the temperature of the bearings have been made, but the result is not accurate enough due to the proximity of the rollers in the idlers

Jan 1, 2019

By Mohammad Irshad, Klaus Mussger, Harald Wagner

Despite the fact that the New Austrian Tunneling Method; NATM, has been used in the United States for the past 23 years or so, still considerable misconceptions exist in the industry about the nature of the method and its implementation. In the authors’ view its implications are usually not well understood. The paper provides an overview of the highlights of NATM usage over the past two decades to illustrate the point that NATM is now a well-established tunneling method in the U.S.A. Accordingly the thrust of this paper is on the more pragmatic aspects of the NATM technology usage as it concerns the Owners, Designers and the Contractors. Prior to examining the implications of NATM usage from the viewpoints of various stakeholders, it should be helpful to first briefly provide an overview of the history of the method as it was introduced and implemented on several key tunneling projects in the US, over the last 2 plus decades.

Jan 1, 2005

By Stanisław Lasocki

We present an algorithm to integrate the uncertainties of mean activity rate and magnitude cumulative distribution function in the interval estimation of the primary seismic hazard parameters: the exceedance probability and the mean return period. The algorithm is applicable for both the parametric and nonparametric modeling of magnitude distribution. When the Gutenberg-Richter relation-based parametric model of magnitude distribution is used, the interval estimation of its parameters is based on the asymptotic normality of the maximum likelihood estimators. When the nonparametric kernel estimation of magnitude distribution is used, we apply the iterated bias-corrected and accelerated method for the interval estimation, based on the smoothed bootstrap and second-order bootstrap samples. Previous studies indicated that the uncertainty of mean activity rate significantly affects the interval estimates of hazard functions only when the activity rate is low and the inference period is not long (Orlecka-Sikora & Lasocki 2017). With increasing mean activity rate, the uncertainty of magnitude distribution dominates over the uncertainty of mean activity rate in the aggregated uncertainty of the hazard functions. The provided algorithm is generic and can be applied to capture the uncertainty of any multiparameter function from the uncertainties of its parameters. Here we present a further development of the algorithm developed by Orlecka-Sikora & Lasocki (2017) by presenting its implementation in the Traffic Light System approach. As an example of use, we present the confidence intervals estimation of hazard parameters for the datasets related to induced seismicity accompanying underground exploitation of copper ore in the Legnica-Głogów Copper District (LGCD) in Poland. The algorithm is under implementation to the EPISODES platform (https://tcs.ah-epos.eu/) - an IT platform that provides access to integrated research infrastructures of the Thematic Core Service of Anthropogenic Hazards (TCS AH) of EPOS (European Plate Observing System). The algorithm is also a component of the pilot developed within the EPOS SP project (No 871121), which aims to strengthen the interaction with the private sector and the added value for society. The pilot demonstrates the potential of the IS-EPOS platform software applications for the technology-related probabilistic assessment of time-dependent seismic hazard. The pilot supports a Traffic Light System approach. The current seismic hazard is compared to threshold values based on the exceedance probability for a given magnitude.

Apr 26, 2022

By Henning Schwarz, Ade Ogunsola, Anas Almousa

"The Riyadh Metro, commissioned by Arriyadh Development Authority “ADA” - the executive arm of The High Commission for the Development of Arriyadh -, forms part of a new public transport-system of Saudi Arabia’s fast growing capital city. The Design & Build project consists of 176 km of Metro Line with 57 km of tunnels. Beyond the Design and Construction, an additional aim of the ADA is to introduce up-to-date methodologies and improve safety in construction projects. A systematic dilapidation survey of buildings and infrastructures was a prerequisite for designing the required instrumentation and monitoring tools. Site investigations required of existing methodologies and the use of geophysical methods for achieving reliable results. Large diameter TBM tunneling is challenging in hot weather conditions and karstic ground. The present paper shows how modern technologies for underground construction are introduced into the local industry and gives an outlook on future projects in the Kingdom of Saudi Arabia. INTRODUCTION Riyadh, the capital city of the Kingdom of Saudi Arabia, is a fast growing city with more than 5.7 million inhabitants. The growth of the city is linked to the recent history of the Kingdom, where some initial milestones from the 1950’s can be highlighted: Revenue generation from the exportation of oil from the Kingdom; downstream investment of oil revenue in the reconstruction and development of the Kingdom; a general plan for the settlement of the Bedouins; the provision of a public electricity network for the city; the opening of the Riyadh - Dammam railway corridor providing a link from the capital to the Eastern Region; the commissioning of Riyadh airport (converted to Riyadh airbase, after the opening of King Khalid International Airport in 1983); and the relocation of ministries and other central government agencies in 1955. In 1974, The High Commission for the Development of Arriyadh was established as the organizational, planning, executive and coordinating body responsible for the development of Riyadh. Arriyadh Development Authority “ADA”, established in 1983 is the High Commission’s executive, technical and administrative arm. The ADA is responsible for implementing the High Commission's organizational, planning, executive and coordinating decisions and missions. The ADA’s president is a member of the High Commission (ADA 2015). One of the remits of the ADA is the preparation and execution of a transport plan for the city of Riyadh."

Jan 1, 2016

By Patzen Wu, Chao-Ming Tsai, Shaw-Chii Wu, Yuan Lin

INTRODUCTION The development of nuclear industry in Taiwan requires an increasing supply of uranium. Uranium recovery from phosphate ores, becomes an important item of the R & D programs. Many countries have already started such a program. USA has set up an industrial-scale production plant; South Africa, Israel, Morocco and other countries have also engaged in the development of extraction technology of uranium from phosphate ores and started setting up the production plant. In Taiwan, a feasibility study of establishing the production plant was started in 1977. A pilot plant was completed, tested, and operated in 1979. The main source material. - phosphate ores is obtained from China Phosphate Company. The annual yield of the pilot plant has been planned to be one ton of ammonium diuranate (ADU). The Health Physics Division of Institute of Nuclear Energy Research (INER), Atomic Energy Council of Republic of China (ROC AEC), is responsible for the radiation safety control of the plant. The purpose of the radiation safety control is to collect radiation safety information of the plant of this type, to evaluate possible radiation hazards to the personnel, and to analyze the radiation safety of the immediate environment adjacent to the plant. Furthermore, the information and experience obtained are used as the basis for applying radiation safety control to the production plant. The main emphases of the radiation safety control are therefore the arrangement of radiation safety control areas and the collection and evaluation of the health physics data. This report includes the past one and half years' experiences of the radiation safety control of the pilot plant, the planning of the production plant with an annual yield of 10 ton ADU, and considerations given in improving the radiation safety control of the production plant. PILOT PLANT AND ITS OPERATION PROCESS The pilot plant occupies an area of 350 m2 and is a two-story rectangular building. Exits are provided by a front and a rear door. An additional small door at the central right side of the building is connected to the maintenance area located outside the main building. The interior of the building is divided into interconnected offices, laboratories and process area (Figs. 1 and 2). A stairway to the process area of the second floor is located in the central part of the first floor. The second floor offices are accessible by the additional front and rear stairways. The main process area of the first floor is furnished with plastic floor, and the second floor with poriferous iron-grid floor. The building is not furnished with centralized air-conditioning system. Individual air conditioners are, however, available to some laboratories. Because the back door of the building is frequently open, the product storage room is provided with a blower to maintain good ventilation. Natural uranium contents of phosphoric acid solution vary in the range from 0.07 to 0.11 kg/m3. The process consists mainly of the uranium concentration cycle and the purification cycle. A flow diagram of the process is shown in Fig. 3. CONSIDERATIONS GIVEN FOR RADIATION SAFETY CONTROL AND THE ESTABLISHMENT OF RADIATION CONTROLLED AREAS The radiation safety control of the pilot plant is carried out on the basis of the considerations listed below:1,2 1) Since the wet process is adopted, and the flow of the radioactive material is confined to closed pipes and containers, air contamination is therefore not too much of concern. 2) The concentrations of radioactive material of the whole process are mostly less than 10 ppm. An exception is the final ADU product after precipitation and centrifugal separation, which contains up to 50% natural uranium. It is therefore necessary to apply radiation safety control to the process area where

Jan 1, 1981

By T. B. Whitmoyer, J. E. Sneckenberger, M. A. Jerabek, C. F. Stanley

The measurement of acoustic impedance at frequencies up to 6,400 Hz has been proposed as a diagnostic tool to yield more detailed information about lung condition. A three generation branching system of plastic Y-tubes has been constructed. The impedance of the branched system is measured by an impedance tube using the two-microphone technique. The impedance spectrum is used to calculate the reflection coefficient spectrum, which is converted to an impulse response by an inverse FFT. The area function is extracted from the impulse response by the Ware-Aki algorithm. Measurements of acoustic impedance of the branched system were made for several different end conditions of the eight terminal outlets. The outlets were either blocked with modeling clay, plastic packing material, or aluminum blocks or were unblocked. Six measurements were made of each configuration. In general, the more outlets blocked, the larger the shift to the right of the impedance magnitude peaks for frequencies above 3000 Hz. The impedance magnitude peaks for the plastic packing material were shifted in frequency to the right relative to the peaks of the other system terminations. The impedance magnitude peaks for the clay and aluminum system terminations were significantly different in magnitude but not shifted in frequency. The area functions at the end of the branched system were significantly different (a > 99%) for most of the end conditions. Area functions for the modeled branched lung systems between the end of the impedance tube and the termination outlets of the branched system were similar but distinctively different for the various end conditions. These results indicate that the two-microphone technique can sense small changes in the terminating end conditions of a rigid system of branched tubes and thus may sense impedance changes due to lung disease in the conducting airways. Keywords: acoustic impedance, lung model, area function.

Jan 1, 1991

By Y. J. Wang

Optimal sizing of a ventilation shaft is a classical subject in mine ventilation economics.. The shaft size is optimized by minimizing the sum of shaft-construction and ventilation-power costs, or owning and operating costs. The length and air quantity of the shaft are held constant, and the location of the shaft, affecting its depth, and construction and ventilation power costs, is not considered (Hartman, 1961; Lambrechts, 1974; Wang et al., 1978). This paper proposes an approach by which the location and size for a new pair of shafts (intake and return shafts) are optimized for a coal-mine ventilation network. Specifically, the problem is to determine the location and size for a new pair of shafts, and the distribution of air between the new and old shafts so that the combined cost of shaft construction and ventilation power is minimized. The shaft length or depth corresponds to the height of overburden at any shaft location. To simplify the problem, the shaft locations will be limited to the line along the main or submain entries, and the connection entries at the shaft bottom neglected. In order to calculate the ventilation-power cost, the air power of the system should be determined. This in turn requires the calculations of the air quantity and pressure of each fan in the network, satisfying Kirchhoff's laws and Atkinson equation. After obtaining the air power, the cost calculation is straightforward. In the following, we shall assume that the resistances of all airways, and the quantity for each mining section, which is controlled by adjusting the air regulator, are all known. The resistances for the shafts are determined from the estimated friction factors, and shaft dimensions and lengths. Furthermore, it will be assumed that the fans can be selected to meet the duties called for by any network solutions.

Jan 1, 1982

By Wei Bin, Liu Zhe, Liping Xiao, Jichi Bai

The Acid Mine Drainage has characteristics of low pH, high concentrations of heavy metal ions, such as Fe2+, Mn2+, Cu2+ and Zn2+. In this paper, the composite particles that consisted of bentonite and steel slags were used to dispose the Acid Mine Drainage. Bentonite is the mineral materials and can adsorb heavy metal ions excellently. The steel slags are alkaline and industrial solid waste for the treatment of the Acid Mine Drainage. The main influencing factors, such as adsorbent dosages, shaking rates, concentrations of heavy metal ions, temperatures, adsorption time and pH value were studied by the static experiment. Increasing the adsorbent dosages and the concentrations of the heavy metal ions, speeding up the shaking rates, raising the temperatures, extending the adsorption time and improving pH would improve the removal efficiencies of heavy metal ions. Through considering the removal efficiencies and the treatment costs, the optimum reaction conditions for the four kinds of heavy metal ions were obtained. The adsorbent dosage 21 mg/L, the rotational speed 120 r / min, the temperature 25?, adsorption time 100 min and the initial wastewater pH 7. The four kinds of heavy metal ions existed independently in the simulated mine wastewater. The highest initial concentrations of Fe2+, Mn2+, Cu2+ and Zn2+ were 150 mg/L, 100 mg/L, 170 mg/L and 140 mg/L respectively. The removal rates were 93.42%, 92.64%, 93.86% and 95.17% respectively. The determination of the particles’ SEM-EDS Microscopic characterization showed the composite particles could play a part in neutralizing, absorbing and the chemical precipitation. The acidity decreased notably and the heavy metal ions of Fe2+, Mn2+, Cu2+ and Zn2+were adsorbed and precipitated effectively. The research results can extend the practical engineering application of the composite particles.

Jan 1, 2017

By R. Bhaskar

The control of quartz levels in the respirable dust requires an approach different from that used to control respirable coal dust. The unique physical properties of quartz have to be utilized when developing quartz dust control systems. Also, techniques that modify the surface properties of quartz dust so that conventional dust control measures are effective should be explored. For instance, the wetting characteristics of quartz can be modified so that the capture efficiency of the quartz dust can be improved. Foam sprays assist in modifying surface wetting characteristics. This paper summarizes the results of a study that was conducted in an operating mine to evaluate the effectiveness of a compressed air foam spray system installed under the boom of a continuous miner and directed so as to cover the pan and the gathering arm. The objectives of the study were to evaluate the effect of the foam underboom sprays on (1) the respirable dust concentration in the ambient air, (2) the quartz concentration in the respirable dust. The engineering design of the foam generation and delivery system is described in the paper, followed by a description of the mine and the dust sampling strategy. The data were analyzed to study the effect of foam on respirable dust and quartz concentrations at the miner cab, face return and the intake. The results of the data analyses and costs are presented in the paper.

Jan 1, 1991

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By J. Roufagalas

Sustainable development requires that exploitation of environmental resources is such that it does not result in permanent damage to the environment. In many instances environmental damage is an external cost of the entity exploiting the resource. Ideally, the entity should be forced to internalize this cost. Various financial assurance schemes have been proposed to ensure that the entities fulfill their financial responsibility to restore the environmental dam-age. Prominent among these schemes are ?environmental bonding requirements?. A main issue with these financial assurance schemes is that many times the amount and duration of environmental damage is uncertain. That is, the cost of restoring the environment in the future may be unknown (or unknowable), and, furthermore, the extent of the damage may not be known for many years into the future. Nevertheless, bonding requirements have to be set in advance and the rules for returning the bond and absolving the entity of responsibility have to be specified ex ante. In practice, a problem of allocation of resources arises. To make sure that all external costs are internalized, in the face of uncertainty, will require a sufficiently (arbitrarily) large bond for a sufficiently (arbitrarily) long period of time. But such a requirement may prove too expensive and may result in not undertaking a project (even if, under certainty, the project may be profitable after internalizing all costs). This will result in a reduction in total welfare. Under present bonding requirements, firms are responsible up to the value of the bond. This results in an asymmetry: if environmental restoration is less than the bond amount, the firm has an incentive to restore and reclaim the bond; if the cost of the environmental restoration is above the value of the bond, the incentive is to forfeit the bond, imposing on the government/ society the excess cost. This also may reduce social welfare, at least on distributional grounds since the firm owners pocket the profits and the taxpayers foot the bill. The presence of uncertainty suggests that a fee based reclamation fund may be welfare enhancing. The thinking can be sketched as follows: All firms undertaking environmentally sensitive projects pay into the proposed fund. The fund examines the risks and sets the premiums at the level of the expected restoration costs (not the maximum!) plus administrative expenses. One advantage of the scheme is that this eliminates the asymmetry. Firms with restoration costs below expected end up subsidizing firms whose restoration costs were underestimated. In other words, the industry ends up internalizing the costs not internalized by the individual firms, instead of the taxpayers.

Jan 1, 2007

By Qing Wang, Xiaochuan Xu, Jianping Liu, Xiaowei Gu, Qingyu Zhu

"The ecological costs related to the various optimized production schemes were calculated based on the designed ultimate pit. Moreover, the influence of the ecological costs on the selection of production schemes was discussed. In one designed pit, a series of geologically optimum pushbacks with sufficiently small increment were produced using the floating cone method founded on the principle of the highest metal content. Then all the pushbacks were reordered by the dynamic network diagram. The production scheme with the maximum NPV route was considered as the optimum one. The ecological impacts produced by mining were quantified and the ecological cost calculation models, which contain the direct eco-value loss, the indirect eco-value loss, the eco-restoration cost and the carbon emission cost were proposed. In one big open pit mine case, various production schemes were optimized and the one with maximum NPV was selected without taking into account the eco-costs. The scheme with the maximum comprehensive profit was obtained by calculating the eco-cost of each scheme. The results showed that the best scheme considered with the eco-cost was not the scheme with the maximum NPV. Therefore, the eco-cost presents the effect on the selection of the best production scheme.Introduction Optimizing production scheme is to determine the mining quantities of ore and rock, the pushing position of stope each year, and maximize the NPV of mine. In the theory, production scheming optimization has gone through trial and error (Pana and Carlson 1966), linear programming method (Johnson 1968), mixed integer programming (Gershon 1983), integer mapping (Kim and Cai 1990), dynamic programming et al (Gu et al 2014). In recent years, the study on production scheduling optimization has been focused on two aspects. On the one hand, the study is to solve the investment risk caused by the uncertainties of economic and geological environment (Ramazan and Dimitrakopoulos 2013, Marcotte and Caron 2010, Lamghari and Dimitrakopoulos 2012, Godoy and Dimitrakopoulos 2004, Benndorf and Shishvan 2014). On the other hand, the emphasis of the study was on reducing the problems for the optimization algorithm, to make it more efficient and practical (Cullenbine et al 2011, Shishvan and Sattarvand 2015, Askari-Nasab et al 2011, Nasab et al 2010). However, different production schemes cause different damage of mine land and pollutant emission, thus triggering environment problem. With the improvement of people’s consciousness of environment protection, the environmental issue of mining has been attracting more and more attention."

Jan 1, 2017

By D. Gu, B. Lin

Discussion of concept Breakage of rock by machine is one of the major methods of excavation. With the development of modern engineering techniques, the advantages of using this method have become even greater. Improving efficiency and reducing the cost of rock breakage is the main goal of mechanizing the rock-breaking operation. For a given stratum, the efficiency of a machine excavation depends, to a large extent, on the design and method of application of the tools used. In a planetary cutter head, the subcutter heads move like planets around the main drive shaft. The general structure of the cutter head is shown in Fig. 1. As shown in this illustration, the main drive shaft (1-1) is connected to the tie bar (1) and, thereby, to a gear (5) that meshes with a fixed-gear ring (2). The subcutter head (4) is rigidly connected to the gear (5) by the subcutter-head axis (2-2). When the main drive shaft (1-1) rotates, the subcutter head (4) rotates around the axis (2-2), under the action of the tie bar and with the help of sleeve pipe (3). At the same time, axis (2-2) also rotates around the main shaft (1-1). As shown in Fig 1, [a] is the angle between the main shaft and the subcutter-head axis. This angle determines the shape of the drilling face. If [a] equals zero, the drilling face will be a flat surface (Fig.1 (a) ), and if [a] is greater than zero, the drilling face will be a spherical surface (Fig. I (b)). For a planetary cutter head, the most important design parameter is the transmission ratio (i), which is defined as [i = (0210)1(1)] Where [(a] is the angular speed of rotation of the subcutter heads around their individual axes, and [o] is the angular speed of rotation of the subcutter-head axes around the main shaft. In Eq. (1), i is positive if the direction of rotation of a subcutter head around its axes is the same as the direction of rotation of the subcutter-head axes around the main shaft (see Fig. 1(b)). Conversely, i is negative when the two directions are opposite (see Fig. 1(a)). When i is positive, the cutters on the subcutter heads form epicycloid paths on the drilling face, as shown in Fig. 2(a). Conversely, if i is negative, the paths will be hypocycloid, as shown in Fig. 2(b). It should be noted

Jan 1, 1996

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016