Search Documents

By T. Faulkner, S. A. Richards

"The Scale-Distance formula is one of the primary means of determining the maximum amount of explosives that can be safely detonated at one time by a single delay. This paper describes a method of applying the Scale-Distance formula to the entire mining area using gridded surfaces. Using this technique, the operator can better determine the economic impact of nearby structures on the mine plan. INTRODUCTION As the surface mining of coal and stone encroaches near populated areas, precautions must be taken to minimize blast vibration damage to protected structures. The common method employed to minimize vibration damage is not to reduce the total amount of explosive in the hole (which would negatively affect fragmentation), but rather to introduce delays to reduce the amount of explosive detonated at any point in time. The Scale-Distance formula, an industry-accepted standard, may be used to calculate the maximum weight of explosive that can be detonated at one time without damaging the structure. This information may then be used to determine the number of delays required for each hole. Detonators make up a large part of the cost of blasting. At roughly $15 per detonator an additional detonator in the hole can be significant. It is normal to set off hundreds of holes at in one shot. An additional detonator in each hole can cost additional thousands of dollars per shot. The number of detonators is also a function of the depth of the holes and the hole spacing. Being able to accurately forecast the economic impact of blasting near structures improves a company’s ability to make informed decisions on how to approach property owners. Operators basically have three options when dealing with property owners: 1. Buy the property and blast without restriction 2. Negotiate with property owner for a waiver to allow unrestricted blasting 3. Comply with the legal blasting restrictions This paper proposes a method for the engineer to forecast for all points in the proposed mining area the impact of nearby structures upon the blast design. Being able to create a contour map and ultimately estimate the number of delays required for the entire forecasted mining area, the engineer can create accurate economic forecasts of the cost of blasting. The objective is to reduce the level of uncertainty in the forecast of the blast component portion of the forecast."

Jan 1, 2016

By P. Rostami

It is important to study the ventilation system in order to better design and control of the working environment in deep underground mines. With increasing depth, heat, and humidity performance may be reduced and impair the attention of workers. The purpose of this paper is to apply a complex; development-end model configured in the MULTIFLUX program, developed at the University of Nevada, Reno, USA. The MULTIFLUX development-end model template has been benchmarked against measurement results from two UK coal mines in previous studies. The present study is a test of MULTIFLUX application in a metal mine. The model incorporates the simulation of the air flow field in the drift and the auxiliary air duct; simultaneous heat and humidity transport from the drift wall; heat and mass exchange between the air in the drift and the ducts; and the evaporation of process water and/or condensation of vapor as governed by the psychometric conditions. The results are compared with field data, measured at the Lucky Friday Mine (LF) in Idaho, USA, an underground mine and also shown between the results from the MULTIFLUX-based model, and those from another program, Kduct, developed at the Kyushu University in Japan.. Gao, K. Uchino & M. Inoue Fukuoka, Japan (2002)?

Jan 1, 2011

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By H. Akbari

The ordinary Portland cement (OPC) is the key pozzalonic component of the concrete mix, widely used as the construction material world-wide. Billions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of CO2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic CO2 emission each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon foot print of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the non-metallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned to extract some of the valuable metal oxides from fly ash prior to using the major non-metallic portion of the fly ash for geopolymer concrete application. The results obtained from this study exhibited that the compressive strength of the geopolymer concrete compares favorably with that of the conventional concrete prepared using the OPC.

Feb 27, 2013

By Changjiang Li, Jun Yang, Qiang Fu, Xu Chang, Xing Wu, Yubing Gao

With the development of underground mining, the deformation of roadway floor has increasingly become a major constraint on the safe and efficient production of coal mines. To address the floor deformation that was caused by massive stress concentration in roadway, an innovative method based on deep-hole directional tensile blasting technology is put forward. By taking No.122108 working face in Caojiatan Coal Mine as engineering background and analyzing the mechanism of deformation, a numerical simulation and field test are carried out to verify the effect on deformation control of this technology. It is found that the deep-hole directional tensile blasting technology can actively control the fracture position of the roof in the gob area and cut off the stress transmission path, so as to relieve the stress in the roadway. And since different blasting parameters have different impacts on the stress relief effect, a numerical simulation is implemented and it is found that the stress relief effect is the best when blasting depth is set to be 32 m and the blasting angle be 60°. By applying the optimal blasting parameters to the field engineering test, it can be seen that the deep-hole directional tensile blasting technology could effectively reduce maximum stress value and stress field range of the both sides of the roadway, and make the stress field far away from the roadway, thus effectively controlling the deformation of the roadway floor. The deep-hole directional tensile blasting technology can effectively solve the problem of roadway floor deformation and can be safely applied to engineering sites.

Jun 13, 2023

By Ping K. Di

A naturally aged and synthesized manganese oxide-coated granular media was found in our laboratory to have the capability of the removal of soluble Mn(H) from mine drainage by adsorption and oxidation. Mine drainage commonly also includes other heavy metal ions. Extending this principle, this paper presents the removal of heavy metals including lead, copper, cobalt, zinc and nickel in the aqueous solution by using the synthesized manganese oxide-coated granular media. It was found that the adsorption of lead, copper, cobalt, zinc and nickel on the manganese oxide-coated media follows both Langmuir and Dubinin-Radushkevich adsorption isotherms except in the concentration range less than 0.1 mmole/L. The adsorption mechanism involves the ion exchange between the heavy metal ions and synthesized manganese oxide coated on the media. The synthetic manganese oxide surface has a strong metal binding ability to the heavy metals in the order of Pb2+ > Cu2+ > Ni2+ > Zn2+ > C02+ based on the adsorption results using batch and continuous column operations. The breakthrough curves of these heavy metals showed that the synthesized media could be used effectively in the removal of these heavy metal ions in a cell or packed column. The process can simultaneously facilitate the immobilization of the heavy metals on the synthesized manganese oxide coated media. A subsequent pH adjustment dislodges the heavy metals and regenerates the synthetic media. Thus, the process accomplishes the adsorption, immobilization and concentration of the heavy metal from waste stream in one monolithic procedure.

Jan 1, 1995

By Mahamuda Abu, John Kalimenze, Benatus Norbert Mvile

The central Dodoma region of Tanzania is one of the regions defined by the Tanzania Craton (TC). Although the Craton gold mineralization has been well explored and hosts most of the gold deposits in the country, the understanding of the mineralization potential of the Dodoma region is still an enigma. This study using trace elements geochemistry of soil samples aims basically at providing information for future exploration works in the region by delineating the possible mineralized zones, the pathfinder elements, and the lithological facies to target. Generally, there is an anomalous spatial distribution of a probable Cu-Au deposit in the N, NE, S, and SE parts of the region and are prospective areas worth exploring for gold from the Gaussian variogram models. The multivariate statistics shows that Cu, Pb, Zn, and Fe are the main pathfinder elements while searching for Au mineralization in the region. The gold deposit is most probably a Cu-Au porphyry type, although VMS type of Au deposit cannot be precluded in the area. The mineralization in the area is largely associated with tonalitic orthogenesis, tonalities, granodiorite, and granitic rocks with Cr-Ni-Co-V forming elemental association. This elemental association is similar to other gold bearing greenstone belts. The style of mineralization in the Dodoma region is similar to other gold deposits within the TC; hence, successful exploration methods in these ancient gold deposits like Geita and Kahama gold deposits can be adopted in the event of any further exploration exercise in the central Dodoma region.

Jul 12, 2021

By S. S. Peng

A well designed mining plan is one which minimizes the cost and the mining induced problems and maximizes the recovery of the coal reserve. In order to minimize the negative effects on surface structures caused by ground subsidence process due to underground mining activities, two kinds of practices are commonly employed by the mine operators. One is the support techniques which leaves an area of coal un-mined or partially mined beneath the structure to be supported. The other is the protection techniques which protect the structure when it is subsiding with ground taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting techniques, the only currently available method in the U.S. is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However; The size of the support area designed by this method will be excessively large resulting in wasteful use of coal reserve when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for de-signing the support area. This method is based on a large amount of subsidence data collected throughout a number of major U.S. coal fields and the authors' experience with monitoring and protecting surface structures undermined by longwall panels. It considers the critical deformation in-dices that a structure can tolerate, and depth and height of underground extraction. The support area designed by this new method will not only assure the safety of the structure to be supported but also maximize the extraction of the coal reserve.

Jan 1, 1993

By Patrick M. Hurley

The spreading-ridge, or accreting plate margin, is the primary conduit of metals delivered to the earth's surface. Isotope ratios of lead show primitive mantle values at these sites, indicating that this is true. We can use lead isotopes in any mineral deposit to indicate the degree to which the metal is "primitive" in the sense of having been uncontaminated with U-enriched crust or "crustal" in the sense that it has been cycling at the earth's surface since earlier times. The reason for this is that the upper continental crust has an enrichment in the ratio of U/Pb over that in the mantle, so that old continental leads have a larger radiogenic component. The primitive metals delivered to the surface at the spreading-ridge are transported on the oceanic plate until they reach a subduction zone. Here they become cycled in the "orogen". However, in this process the primitive metals are mixed with metals from the continent so that the average lead isotope ratios are between those in the mantle and the average upper continental crust. Subsequently a part of the metals in the orogen may become fixed in a new block of continent. However there are processes which continue to uplift and erode ancient continental regions so that there is a continuous feeding back of metals to the orogen. We have therefore a cycling of metals from the existing continental crust into the orogen where they are mixed with new contributions from the spreading ridge and mantle.

Jan 1, 1977

By William F. Jenks

The possibility that a hypothesis explains almost all observed facts may be satisfying. Yet the almost gives a distinct sense of uncertainty. Moreover, overlooking the almost, reliance on the favored hypothesis may close our eyes to the discovery of new information and, in the field of mineral exploration, to the possibilities of finding new and hidden ores. A case in point is that of mines such as the Elizabeth and Ely, along the copper belt in eastern Vermont, principally in Orange County. The geology of the Strafford Quadrangle, where the Elizabeth Mine is located, has been described by Doll (1944). Two informative papers (McKinstry and Mikkola, 1954, Howard, 1959) present much valuable information about the geology of the Elizabeth Mine. Both reach the conclusion that the ores were emplaced after the peak of metamorphism, through the agency of metal-bearing hydrothermal solutions. Both, therefore, conclude that the source of the ores was somewhere below the outcrop area, presumably in some hidden intrusive mass. Neither yields a satisfactory guide for further exploration. Howard (1959) cites geophysical observations which show that there is a mass with a density similar to that of granite under the Strafford dome, adjacent to the Elizabeth Mine on the West. Yet examination of gneissic granite in the Chester dome, 25 miles to the South gives no suggestion of a young, near-surface intrusive capable of carrying or mobilizing large quantities of sulfur and metals. The Acadian intrusives in New Hampshire and in the Barre district

Jan 1, 1968

By A. K. Mukherjee

The roles of pulsating mechanisms such as the amplitude and frequency of the jig cycle are well established in jigging. Also well established are the roles of the size ratio and the volume fraction of the feed. In iron ore beneficiation plants, these process parameters are optimized to achieve the highest efficiency. However, the role of one of the more important feed characteristics, the liberation characteristic of the feed, has not been studied in detail. Evaluation of the liberation characteristics is difficult because the required washability test is not viable for iron ore feed. In this paper, a new method is proposed in which the liberation characteristics are measured through a separation efficiency value. In the new evaluation method, jigging parameters such as amplitude and frequency of the jig cycle are optimized from the fundamental understanding of the process dynamics and feed characteristics such as size distribution. Then, feeds with different liberation characteristics are tested to evaluate the liberation characteristics of feed in jigging.

Jan 1, 2008

By M. Sagisaka

The purpose of this study is to obtain carbon dioxide emissions by copper production systems and quantitative merit to use copper scraps in Japan. Electrolytic copper and sulphuric acid originating from the refining gas are produced in the system. In this study, the inventories such as the fuel consumption of the unit processes and the in-house electricity generation were obtained from published papers and public statistical data. The following observations were made based on the Life Cycle Assessment (LCA) method: (1) Carbon dioxide emissions from the production of electrolytic copper and sulphuric acid in the system are about 1.0 kg and 0.4 kg/kg-product respectively. The carbon dioxide emissions attributable to the transportation of copper concentrate correspond to 20% of the total emission. This emission is higher than that of zinc because the metal content in the concentrate is lower than zinc. (2) The carbon dioxide emissions from the system decrease with the recycling of copper scrap to the converting process because the consumption of copper concentrate is reduced. The reduction is estimated to be 0.18 kg-CO2/kg-Cu at the point of 0.1 kg-scrap/kg-blister Cu. This corresponds to 9% reduction for the present system. However, this recycling leads to the decrease of sulphuric acid by 450x103 tonne at the point. The recycling of scrap should be evaluated not only from the reduction of carbon dioxide emissions, but also in terms of sulphuric acid demands as well as advantage of waste management.

Jan 1, 2003

By E. Koufetzis

Rock mass classification systems are core elements of tunneling and empirical mine design worldwide. The Bauxite division of S&B Industrial Minerals S.A. decided to implement a rock mass classification system in order to provide mining engineers and supervisors of the underground mines, with guidelines of stability performance and with a complementary tool for the selection of the appropriate tunnel support. The back analysis system employed is based on visual observation of especially selected underground mine sites, representative of all rock types. This fact combined with the failure or success of the already existing support system, constitute the fundamental part of the work undertaken. The paper is divided into three main parts. In the first part the classification methods of Q, RMR89 and GSI are presented and the advantages and disadvantages of each method in connection with underground mining are indicated. RMR89 and GSI are conclusively selected for use, the main criteria for the selection being, the simplicity in use and the competency of the support system suggested for each rock mass category. The second part points out the methodology for measurements, the practical difficulties encountered during this process and the guiding principles followed, in order to avoid these problems. In the third part, the final conclusion of this project is demonstrated and the different rock mass categories are presented with their relative support recommendations, as they were applied and tested in all phases of the bauxite mines? exploitation. The generated methodology is being implemented by the site mining engineers, for validation and potential improvement.

Jan 1, 2008

By K. L. Myers, R. Espell, C. Deringer

Construction of the AA Pad reclamation was completed in the fall of 2000. Seeding of the ET cover began in the late fall of 2000 and continued through May of 2001. On Saturday afternoon, June 1, 2002, a large, very localized thunderstorm struck the reclaimed AA Pad site. Eyewitnesses present at the time described a dark storm cloud parked above the site for less than half an hour. Average rainfall intensity was measured to be 122 mm (4.8 inches) per hour and peak rainfall intensity was estimated to be 213 mm (8.4 inches) to 259 mm(10.2 inches) per hour. At the time of the storm, the construction was less than two (2) years old and the vegetation had only a single season of growth. The entire period from the end of construction until the date of the storm was a drought period with below normal precipitation. Other than a few small snowmelt events, there was no precipitation event large enough to produce any significant flow in the channel network. Therefore, the very first significant runoff event was the extreme event of June 1, 2002. The storm essentially represents a large-scale field test of the design concepts used at the AA Pad site. Shortly after the storm, data was collected and analyzed with the intent of learning as much as possible about the performance of the cover system design with the expectation that the newly acquired knowledge might be utilized in future designs to further improve the performance of similar cover systems during extreme events.

Jan 1, 2003

By Debbie Nakamura, Daniel Tempelis, John E. Shamma

The Metropolitan Water District of Southern California established a Board of Consultants to assist them in administering the design and construction of the Inland Feeder Program tunnels. The Board acts as an expert review body for the owner, looking at key issues that can potentially impact the success of the program. The use of the Board evolved over the life of the project, and its composition was modified to better address the needs of the owner, and the Program requirements. The experience, function, and value of such a board is analyzed and discussed in this paper.

Jan 1, 2003

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By R. K. Rajamani

The theoretical model based on fluid mechanics, in conjunction with the laser-Doppler velocimetry (LDV) measurements, elucidate the size-classification mechanisms in an industrial hydrocyclone. The model has no adjustable parameters and involves solving the Navier-Stokes equations to predict the liquid-phase velocities. The spatial-concentration gradients were determined considering the particle phase in the Lagrangian frame and the classification curve was determined by balancing the forces acting on the particle. The force balance requires liquid velocities, which in turn depend on the local volumetric concentration of the particles. Hence, complete modeling work involves coupling both the concentration and liquid-phase velocity calculations until convergence is reached. Finally, the experimental and predicted classification curves were presented for 250-mm hydrocyclone operating at high-percent solids.

Jan 1, 1994

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

By Niels Jonassen

INTRODUCTION The occurrence of the radioactive element radium, [2gg~a], often in trace amounts, in the crust of the earth gives rise to a flux of the daughter product radon, ['ii~n], across the earth-air interface. This so-called exhalation process has been studied by many investigators [KO 45, Kra 64, Pe 66, Wi 741] over several decades. In the earlier investigations the exhalation process was studied in a purely geophysical context, but over the last 20 years it has been realized, that under certain conditions the exhalation may be intense enough to also have radiological implications. This is for example the case where relatively radium-rich wastes or by-products, like uranium mill tailings and phospho-gypsum, are stored in larger quantities. In order to be able to predict the radiological impact on the environnent it is necessary to know the rate of exhalation of radon from the surface of the exhaling material. Usually the determination of these exhalation rates has been done by measurements in situ directly upon the accumulated material [~le 74, Ha 791. Although such field measurements have the obvious merit of dealing directly with the full scale problem, the results are often lacking in generality, making predictions for other situations difficult or even impossible. The present paper describes some results of an investigation where it is attempted from laboratory measurements on samples of limited size to obtain material parameters, which are suited for extrapolating and predicting the radiational behaviour of larger accumulations of the material. THEORY Let us consider a sample of a radon exhaling material enclosed in a container with a dead space volume, Vd, and initially containing radon free air. If the total exhalation rate (number of atoms per unit time) is c, the radon concentration (number of atoms per unit volume) N will initially grow with the time t according to the equation [ ] where [R] is the decay constant of radon. As the concentration (or activity) in the container grows, the net exhalation rate will slow down because of back diffusion, and, furthermore, radon atoms may be removed from the container, not only by radioactive decay, but also by diffusion leakage [JO 81 ]. If, however,only the initial. part of the activity growth curve is considered, the total exhalation rate, c, is given by [c = r•Vd(2) where r is the initial activity growth rate in the container. Let the container be cylindrical with an inner cross-section S and filled to a height L with a radon exhaling material with the specific mass p, the porosity E, the radon pore production rate f and the diffusion length i. When the container is left open,i.e. the radon exhalation takes place into a virtually radon free room, the radon area exhalation rate, E, can be written [Jo 80] E = Ef?t tanh L.R (3) assuming the exhalation only takes place in one direction, towards the surface of the material. It appears that for values of L > 2•ithe area exhalation rate becomes E a = Efi (4) independently of the sample dimensions and the total exhalation rate c is then c = E •S (5) For L ;~ 0.5•i, tanh P _ k and equation (3) may be written E ~ EfL (6) then c = EfL•S = p•m= Em •m (7) where m is the mass of the sample and Em = P (8) is the mass exhalation rate. It thus appears that the radon exhalation rate from a given amount of material may often be conveniently expressed by c = E •Sfor L z 2•I (5) a orc = Em •mfor L0.5•i (7) where S is the total exhaling area and m the total exhaling mass, E and E the area and mass exhalation rates respectively defined by equations (4) and (8).]

Jan 1, 1981