Search Documents

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By Fred C. Bond

The perennial subject of comminution is deserving of a fresh approach if one can be found. This is attempted here by directing attention primarily to principles rather than to theories. While theories attempt to explain how a certain process acts, principles delineate the laws which the action-must follow. Comminution may be defined as the progressive separation of particulate matter. At the present time this is accomplished commercially by applying energy in the form of compressive and, shearing forces. Such forces strain and distort the particles they contact. When-the applied stress locally exceeds the breaking strength at the weakest flaw in the particle, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends through the particle as a break. The minute changes in shape and the resulting energy flow cause the failure of other highly stressed flaws, with the consequent formation of a progeny (1) of new smaller particles out of its destroyed progenitor. The applied mechanical energy is transformed into strain energy as the particle is distorted, and then into heat when it fails. Only a tiny fraction of the order of 1/1000 of the applied energy necessary for breakage appears as new surface energy in the product particles. The comminution problem is the relationship between, energy input and product particle size. Its solution is of great-economic importance,

Jan 1, 1961

By C. J. Johnson, C. J. Bise

Introduction Coal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation's deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only after ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental compositon of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines. There are several potential contributions of this type of study to the coal mining industry. First, after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies. Further, assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location, a mining company could predict a new mine's respirable dust elemental composition in the immediate ventilation return by using exploratory drill core samples of the roof, coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design, much time and money could be saved. Scope of work To investigate the variability of the chemical characteris tics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and midwestern United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee (1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs. The procedure that was used to produce the laboratory-generated respirable dust was based on the Hardgrove grindability test since it reflects the pulverizing characteristics of coal. This test was chosen for several additional reasons. First, it is repeatable and reproducible. A consistent amount of input energy is used as well as a specified size range of feed material to be crushed (the channel samples). Second, it is thought to generate secondary dust in a way similar to that of the crushing and grinding of the coal and rock as they pass through the arc-shaped cutting path of the CM's cutter head. The potential effect on dust generation by this secondary grinding mechanism may be at least as much as that produced by primary fragmentation, which is dust produced by the cutting action of the bit against the coal or rock (Roepke, 1984). Finally, the Hardgrove grindability test is well known and is used in the coal industry to guide mineral processing engineers in estimating the capacity of mills used to grind coal. One hypothesis of dust researchers in the Generic Technology Center for Respirable Dust is that the elemental as well as the physical characteristics of coal mine dust will make a difference in the incidence and severity of CWP. Coal mine dust is generated not only from coal, but also from any rock partings contained within the seam or any roof or floor material mined with the coal. Thus, coal mine dust may not have the same elemental characteristics as the coal being mined. Given that hypothesis, mixtures proportional to each thickness mined of roof, coal, and floor rock derived from the channel samples of the face areas from which the respirable dusts were generated by the CMs were used to produce the feed material that was pulverized in the Hardgrove machine.

Jan 1, 1989

By C. J. Johnson, C. J. Bise

Coal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation's deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only after ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental compositon of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines. There are several potential contributions of this type of study to the coal mining industry. First, after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies. Further. assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location, a mining company could predict anew mine's respirable dust elemental composition in the immediate ventilation return by using exploratory drill core samples of the roof, coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design. much time and money could be saved. Scope of work To investigate the variability of the chemical characteris tics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and midwestern United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee (1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs. The procedure that was used to produce the laboratory generated respirable dust was based on the Hardgrove grindability test since it reflects the pulverizing characteristics of coal. This test was chosen for several additional reasons. First, it is repeatable and reproducible. A consistent amount of input energy is used as well as a specified size range of feed material to be crushed (the channel samples). Second, it is thought to generate secondary dust in a way similar to that of the crushing and grinding of the coal and rock as they pass through the arc-shaped cutting path of the CM's cutter head. The potential effect on dust generation by this secondary grinding mechanism may be at least as much as that produced by primary fragmentation, which is dust produced by the cutting action of the bit against the coal or rock (Roepke. 1984). Finally, the Hardgrove grindability test is well known and is used in the coal industry to guide mineral processing engineers in estimating the capacity of mills used to grind coal. One hypothesis of dust researchers in the Generic Technology Center for Respirable Dust is that the elemental as well as the physical characteristics of coal mine dust will make a difference in the incidence and severity of CWP. Coal mine dust is generated not only from coal, but also from any rock partings contained within the seam or any roof or floor material mined with the coal. Thus, coal mine dust may not have the same elemental characteristics as the coal being mined. Given that hypothesis, mixtures proportional to each thick¬ness mined of roof, coal, and floor rock derived from the channel samples of the face areas from which the respirable dusts were generated by the CMs were used to produce the feed material that was pulverized in the Hardgrove machine.

Jan 1, 1990

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By G. Jim Cardwell

The question "what constituents should be determined?" is one that defies a simple answer, because earth scientist being what you are, the rock and mineral analyst will eventually be called upon to determine about three quarters of the elements in the periodic table. The concentrations of these analyses will range from as low as 1 ppb to 100% of the material being analyzed. The most important thing to remember about a quantitative analytical result is that it can only be an estimate of the concentration of the analyte present. A measure of the reliability of that estimate is given by statistically derived statements of the precision and accuracy of the measurement. When evaluating your data an understanding of precision and accuracy are of paramount importance. Precision is the measure of agreement between replicate values while the accuracy of a determination is the concordance between it and the true value. There is no quarantee, however, that a precise answer is an accurate one. The numerical difference between the two values is the error. When evaluating your data, the repeats analyzed with your samples will identify the precision and control standards of U.S.G.S. or Canadian Certified Materials quality will identify the accuracy. The main problem is this data is routinely withheld from the report, or was it ever included in the analysis of your samples?

Jan 1, 1983

By N. ?peh

The purpose of the paper is to present a way of assessing nonrenewable lignite resources by means of sustainability indicators. An introductory presentation of the origin and characteristics of the discussed nonrenewable natural resources is followed by the study and analysis of separate sustainability indicators. Out of many, only the ones that would directly relate to the explored coal deposit were studied. Some different viewpoints such as economic, social and environmental were assessed inside the studied landscape structure and in relation to other provincial resources using the indicators that are closely linked with the explored lignite reserves. Exploitation of coal as an underground nonrenewable natural resource, has been taking place in the ?alek valley for more than 120 years. However, about 60% of the coal will still be left underground since not all coal will have been extracted when the mine closes. According to the regional and wider national strategic goals concerning the use of natural resources and electricity production in the future, the sustainable aspect of the exploitation of the geologically well explored reserves is emphasized in the paper. Finally, we have tried to evaluate the role and the meaning of the studied underground natural resources for further sustainable development of the ?alek valley and placed stress on the most questionable spheres that should be considered preferentially.

Jan 1, 2007

By Fredrick J. McGarry, Fred Moavenzadeh

In order to reduce the resistance of hard rocks to excavation by the available cutters, and in order to reduce the wear of the cutters and thus to increase the efficiency of the conventional tunneling machines and to improve their rate of advance in hard rocks, surface active agents have been studied in the controlled laboratory environments and have been experimented with in the field of actual tunneling operations. The laboratory study utilized a notched beam test to measure the effectiveness of 30 different surface active agents on the amount of surface energy required to cause stable fracture in the rock specimens. In addition to the type of rocks, geometry of the specimens, type of surface active agents, the effects of environmental factors such as temperature and degree of saturations were studied. The principle mechanism responsible for weakening of rocks in the presence of surface active agents was believed to be that of stress activated corrosion. The application of surfactants in the laboratory resulted in a reduction of up to 50% in rock strength, while limited experiments in the field have shown a 10 to 20% increase in the rate of advance. Substantial efforts both in the laboratory and in the field are needed to fully understand the mechanism involved and to utilize the effectiveness of surfactants as weakening agents for hard rocks.

Jan 1, 1997

By Andrew H. Merritt

INTRODUCTION The prediction of the engineering behavior of a rock mass depends upon the systematic analyses of the results of an exploration program, and upon the recognition of the significant rock properties in the early stages of excavation. The variations in rock properties in different geologic terrains and the state of the geotechnical art preclude complete success in the former case, and we therefore must rely heavily on the experience gained in the latter phase. The geotechnical information obtained from these two phases is only of value to the design engineer when applied to the rock behavior during excavation and subsequent plant operation. Pertinent questions which must be answered include: how does the joint orientation and frequency effect tunnel support and overall cavern stability; how does the depth of surficial soil or weathering effect foundations or slope stability for portal cuts; are there permeable zones within the rock mass that could lead to leakage problems around penstocks and is the material in these zones soluble or likely to pipe in the long term; and does the proposed engineering structure fit the terrain, or will it inevitably lead to problems requiring extensive remedial treatment. During the early stages of construction there are two types of geotechnical information required; actual rock behavior with respect to the original design assumptions,

Jan 1, 1997

By Steven Johnson

The regulatory landscape has changed considerably since the first passage of Oklahoma's land-reclamation requirements in 1968 (Open Cut Reclamation Act of 1968). The Oklahoma Legislature revised the reclamation requirements in 1971 with passage of the Mining Lands Reclamation Act. With the passage of this Act, the Legislature empowered the Oklahoma Department of Mines with jurisdiction for permitting and regulatory authority over non-coal (industrial-minerals) mining operations. This act required all operators to file with the State, through the Department of Mines, a written application for a permit to engage in non-coal mining. Each application consisted of a mining plan, which included location maps of the proposed mining area along with a reclamation plan for the area to be covered. Additionally, a reclamation bond is required prior to issuance of a permit to ensure that the site would be reclaimed. Since 1971, the Act has been amended to include public notification and public participation in the review process of any application. Also, the operator can request that the Department review the mining plan based on the Life Expectancy of the mine, instead of the original one-year plan (HB 1409 in 1993). Even though the operator is granted a mining plan tied to the "Life Expectancy" of the site, the permit is reviewed annually for compliance as required by law.

Jan 1, 1999

By T. Eisele, T. Weldum, G. Rajala, H. Walqu, S. Kawatra

The throughput and energy efficiency of comminution circuits is reduced when ore characteristics change, causing bottlenecks in some portions of the circuit while leaving excess capacity in others. The results of analysis of three years of daily grinding circuit operating data for a full-scale plant has shown that the location of bottle-necks in the circuit will change depending on the nature of the feed ore. The circuit tends to be limited by the primary mill capacity when the ore hardness increases, and limited by the secondary mill capacity with softer ores. Two methods are considered for shifting load in the circuit to relieve bottlenecks by taking advantage of excess capacity in other parts of the circuit: 1) Addition of supplemental comminution operations, such as high-pressure grinding rolls, to process specific size fractions that are not handled efficiently by the primary mill; and 2) Use of screens to shift grinding load upstream from the secondary mills back to the primary mills. In the case of the plant examined in this study, it was found that 58% of the time there was sufficient excess capacity in the primary mills that the throughput of the circuit could have been increased by using screens to shift the grinding load from the secondary mills to the primary mills.

Jan 1, 2004

Recent accelerated exploration efforts in southwest China have progressively quantified the vast phosphate resources in the Yunnan Province. To date, according to Chinese geologists, potential reserves in the province may be on the order of 4 Gt, which would equal the entire US reserve base. Development of this vast reserve is underway at two sites located 60-70 km southwest of Kunming, the provincial capital of Yunnan. The first, the Kunyang open-pit phosphate mine, produces an estimated 1.5 Mt/a of 22-30% P20,5. The other project located north of Kunyang is the Haikou mine, which the Chinese consider a possible 2.0-Mt/a operation. Because average ore grades run 3% less than those of Kunyang, beneficiation will be necessary. While the latter project has been initiated on a small scale, it is basically still on the drawing board. Brown and Root and the US Bureau of Mines are assisting on the project. Both operations are under the direction a regional administration which reports to the Ministry of Chemical Industries in Beijing. Combined production from both mines could represent some 70% of China's future productive capacity. Ore reserves in the region are estimated at 400 Mt by local officials. Geology of the District The phosphates are considered Cambrian in age and rest on a Precambrian dolomite. The Indian Ocean, Chinese geologists say, may have been the original source. The line of deposition stretches on a trend from Vietnam in the southwest, through Yunnan, into Sichuan Province to the northeast. Because the area is considered very stable from a geologic viewpoint, large quantities of phosphate have been deposited and large outcrops are known to occur everywhere in the province, according to Chinese sources. The Kunyang and Haikou ore bodies are thought to be two wings of an anticline with the former the southern portion, and the latter the northern portion. Each ore body strikes on an east-west axis. While there are many localized phosphate operations throughout the province, the Kunyang mine is the premium producer. Kunyang's Mining Development The Kunyang open-pit mine was opened in 1966. During the early years, operations were considered somewhat disorganized. Systematic mine planning and normal operations were not initiated until just two years ago, according to mine management. In 1979, Kunyang finally reached its design capacity of 1.5 Mt/a. The ore body consists of two phosphate beds separated by a band of shale. The top layer of phosphate varies from 4 to 8 m, averaging 6 m. The middle shale layer is 2 in. The third layer, which is not as rich as the top, is approximately 4 m. To further complicate matters, the ore dips 15° to the south over a strike length that is currently undefined, but believed to be

Jan 3, 1980

By M. Götze, P. Eysel

Over the last years, the importance of the assessment of environmental and social aspects as well as of issues of good governance has increased significantly in mining finance. For this, international standards as well as internal guidelines of the banks and other involved institutions have been established and continuously improved. Considering these standards and regulations, the banks can influence the sustainability of mining projects - and they have done so in the past -, mainly by implementing certain provisions and covenants in the loan documentation, binding the financing to the mining company’s adherence to the agreed sustainability standards. However, there are limits to the banks’ influence due to the competitive environment with other available means of financing. Nevertheless, the experience of the last years has shown that the standards and regulations bound to the financing by the banks help to lead the mining industry towards more sustainable projects.

Jan 1, 2011

By P. C. Thakur

In Part I of this paper, it was established that the width of longwall faces in highly gassy mines is primarily limited by the volume of air reaching the tail-end of the face. The ventilation air reaching the tail-end of the face should be not only enough to keep methane concentrations below the statutory limits (generally 1 percent) but also enough to prevent any gas layering. The air volume leaking from the longwall face into the gob should also be able to push the explosive methane-air mixture away from the gob area immediately behind the longwall face where active roof-fall is taking place (typically 30-45 m). The second group of variables that also controls the width of the longwall panel consists of (a) the rate of advance, (b) bleeder air quantities, (c) specific methane emissions for the gob area and, (d) efficiency and cost of gob gas capture. This paper will discuss the second group of variables and its impact on the optimum width of longwall faces in highly gassy coal mines.

Jan 1, 2009

By M. Sagheer

An 8.5-km (5-mile) conveyor has gone into operation in western Turkey to eco¬nomically transport crushed lignite from the mine area to a power plant. This conveyor has replaced trucks as the principal mode of transporting the lignite. One principal element of Turkish govern¬ment policy is the country's commitment to increase electricity supplies for mining and other industries. Lignite is an important source of electric power supply in Turkey. Production was about 48 Mt (53 million st) in 1987, amounting to more than 20% of the total power supply in Turkey. In the western Anatolia supply network, it plays a major role for power generation. Deposits are located in the Soma region of western Turkey. The lignite is of low quality, deposits are scattered, and the terrain is dif¬ficult and hilly. These conditions demand an economical and technically feasible method of transporting the raw material from mining areas to the central thermal power plant. The Soma power plant is located about 120 km (75 miles) northeast of Izmir, near the coast of Aegean Sea. An overland conveyor of a unique design has gone into commercial operation at the Soma power plant facilities of the Turkish state electricity organization, Türkiye El¬ektrik Kurumu (TEK). The conveyor re¬places truck transport to ensure economical use of the lignite deposits. Computer-aided design (CAD) added more precision, qual¬ity, and flexibility of engineering in design activities. It also helped quick realization of the project that was executed in cooperation with the German company Krupp Industri¬etechnik and the Turkish firm Gama Endüstri AS. Unique features The conveyor includes several major features rarely combined in a single flight: Overland long distance conveyor. • Horizontal curves. -Steep vertical concave and convex curves to match the difficult terrain. Down-hill conveying. Frequency converter drives with vari¬ able belt speed. Generating operation mode to backfeed the energy to the network. Layout The 8.5 km (5 mile) long conveyor takes the -200 mm (-8 in.) lignite from the primary crushing plant located near the mine to the central, final crushing plant located in the stockyard area near the power station. The drive and belt tensioning assemblies are situated near the tail end of the flight. The high voltage switchgear is housed in a room in the primary crushing plant build¬ing upstream from the conveyor flight. The frequency converters are installed in the low voltage switchgear room located below the control room within the primary crushing plant building. Conveyor design The conveyor includes two 4 km (13,120 ft) radius horizontal curves, one left-hand and the other right-hand. The minimum radii

Jan 1, 1989

By Steve Kral

In December 2013, the Colorado Department of Transportation (CDOT) completed the widening of the eastbound tunnel on Interstate 70 (I-70) from two lanes to three. Work on the westbound tunnel began earlier this year and is scheduled for completion in December. The Twin Tunnels project is located in the mountains about 55 km (35 miles) west of Denver. They were bored during the 1960s when I-70 was being built and became the main access to Colorado?s growing number of ski areas and the state?s Western Slope. Throughout the decades following their construction, traffic on I-70 continued to increase and now the tunnels have a major bottleneck. Com-mutes to and from the mountain resorts, particularly on weekends, have become long and slow. Adding a third lane through the tunnels will help alleviate the congestion. (A complete report on the project can be found in T&UC, December 2013, page 61.) Once the eastbound tunnel was completed late last year, CDOT authorized the funding to begin work on the westbound side. That made economic sense, as the equipment used on the eastbound tunnel needed to only be shifted across I-70 to begin work on the westbound side, rather than removing it in December and bringing it back in March when construction began on the westbound tunnel. Work on the westbound tunnel uses essentially the methods that were used on the eastbound tunnel ? removal of the existing concrete lining and using drill-and-blast methods for tunneling widening. The main difference between the two tunnels is that the westbound side requires more blasting on both ends to widen I-70 to three lanes.

By D. M. Bodily, V. J. Hucka

INTRODUCTION Interest in the recovery of methane from coalbeds has increased rapidly over recent years, because of its potential as an energy resource and to alleviate pollution and safety problems. The resource base of coalbed methane in the United States has been estimated at 11.2 Gm3, roughly equivalent to 20 years consumption (Mroz et al., 1983; Kuuskraa and Brandenburg, 1989). Methane contributes to the adverse environmental impacts of global warming, tropospheric ozone formation (smog), and potentially stratospheric ozone destruction. Association of methane with coal has always presented a safety problem in mines due to the potential for explosions. The rate of release of methane depends on the amount adsorbed by the coal, the adsorption isotherm for the coal, and the size of the coal particles. Mining operations can affect the particle size distribution and the production of fines and therefore the rate of release. The time the mined coal remains in the mine may also be important in determining total emissions. The methane content of some Utah coals was determined in this study. The methane content of the coals is compared with the chemical and physical properties of the coals and the properties of the seam and neighboring strata. Correlations are developed to better understand the formation and retention of methane by these coal seams. METHANE FORMATION IN COALBEDS Three mechanisms for methane formation may be considered: (1) nonbiogenic formation, (2) formation by anaerobic bacteria during plant material deposition and the early stages of diagenesis, and (3) formation from pyrolysis of coal material during coal maturation. Nonbiogenic formation by thermal processes involving carbon- and hydrogen-containing compounds has been proposed as a mechanism for methane formation in the earth. It is not likely to be of importance where other fossil fuel materials are present. Coal would not survive the temperatures required and hence the methane would need to migrate and be trapped by the coal seam. This mechanism is unlikely for coalbed methane. Formation of methane by anaerobic bacteria undoubtedly occurs during coalification, but the methane may not be trapped until the pore system of the coal is developed, and would likely be displaced by methane formed during further coalification. Methane formed by maturation of the coal material as it progresses from peat to coals of various rank is the most probable mechanism for the formation of coalbed methane. Most of the methane is adsorbed onto the walls of microvoids in coal. It has been estimated that the surface area of one kilogram of coal is between 20,000 m2 to 200,000 m2. Surface area measurements depend on the coal and also on the method of measurement. At 20 atmospheres, in some coals, the adsorbed methane is 10 times greater than methane as a free gas. At 100 atmospheres the adsorbed gas can be as densely packed as a liquid. The volume of methane gas held in coal depends on the volume of gas that exists as a free gas and the adsorbed gas capacity. The volume of free gas in the coal can be calculated from the kinetic theory of gases (methane can be assumed to be an ideal gas because errors would not be greater than 1 % for normal mining pressures). Langmuir (1916) derived an equation for the adsorption of gases on uniform surfaces and this is applied to the adsorption of methane on coal:

Jan 1, 1993

By R. V. Ramani, C. J. Bise

INTRODUCTION Classification of coal seams as thin, medium, and thick is both subjective and relative and is more a reflection of the statistical mode of the thicknesses en- countered in a mining region. A geological factor more precisely understood as defined than thickness is the inclination of the seams to the horizontal, commonly referred to as the pitch or the dip of the seam. Thick and steeply pitching seams present far more challenges to the ingenuity of the mining men to devise methods for their extraction than the thick and less steeply inclined ones. In a marginal case, where a thick coal seam may be minable by surface or underground methods, the decision bears a close relationship to the technological developments in the mining scene. Near surface thick coal seams are a special gift of nature and are not as wide- spread as the ones that call for the application of under- ground methods. Recent advancements in surface mining equipment have made it possible to surface mine to great depths. Stripping ratios of 30: 1 (cu yd of over- burden removed per ton of coal) have been achieved. The extraction of thick seams which preclude the use of surface methods is the concern of this chapter. Specifically, the objective here is to outline the special technological factors in underground mining of thick coal seams and to illustrate through several case histories the methods that are practiced in the North American continent. For the purposes of this chapter, a thick seam is defined as one which is not readily minable with currently available equipment without modifications to the extraction method or the equipment. At the present time, a thickness of 4.8 m (16 ft) can be considered as the lower limit, although developments in equipment and methods can be expected to push this limit upwards. The data for the case histories were collected from two extended mine visits in 1975 and 1978, and from other published accounts of the mines visited. Reference is drawn particularly to reports by Bise, Ramani, and Stefanko (1976) and Rarnani and Kenzy (1979). THICK SEAM MINING METHODS The various methods of mining thick seams can generally be grouped into three major categories: full face methods, where the entire thickness of the seam is re- covered in a single pass; slicing methods, where the seam is extracted to its full thickness by horizontal or inclined slices either in an ascending or descending order; and caving methods, where the seam is undercut and the en- tire coal seam is recovered by caving the top coal into the excavated cut, or some variations of the basic sub- level caving method. As shown in Table 1, in each of these methods, the coal is removed by either room-and-pillar or longwall methods. Hydraulic mining and transport of the coal in open flumes or in pipelines are also practiced. Addition- ally, the void created by the removal of coal may be filled with a packing material (stowing) except in the caving methods. The pitch (dip) of the seam, particularly when it is greater than 0.26 rad (150), imposes severe operational limitations on mobile equipment. A more detailed general discussion of the methods can be found in Bise et al. (1976) and Vorobjev and Deshmukh (1964). Specific discussion on the many variations of the three basic methods can be found in the papers presented at the international symposia that were held in

Jan 1, 1982

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread-sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin. Computerized search Computerized search approaches represent crude first attempts at letting the computer design the blend. Unfortunately, the blends found by these programs are very often less satisfactory than those developed manually. The way these techniques work is that they design, according to some predesigned pattern, a number of different blends and then quickly evaluate them. It is then straightforward to select the best from this sample set. The quality of the results depends on the number of blends designed, the way they differ from each other (the search procedure), the number of sources available, the number of quality specifications, and the severity of the specification limits. Good results are usually obtained for small, simple problems. At best, the results obtained are inconsistent from one blend to the next. Programs of this type are advertised in the mining literature. They usually mention how many different blends are evaluated, making it clear that this is more than can be tried manually. Expert systems Expert systems use a source of information known as a knowledge base. The knowledge base, usually a set of if-then rules, attempts to reconstruct the deductive reasoning process of an expert in some job capacity. For coal blending, the usual trial-and-error process has an easily recognized pattern of rules that are followed to try to find a better blend. By following these rules, it is possible to home in on the best blend without the exhaustive search required by the previous method and without the manual manipulation of the spreadsheet approach. The use of an expert system accomplishes this. One of the rules may say something like "if BTU is out of spec, then add more in the blend from a source having a high BTU and subtract some from a source having low BTU." In other words, it goes through the trial-and-error process. The process continues until all specifications are achieved and can continue further to try to optimize the cost. Of course, less simplistic rules are also needed. One set of rules would determine maximum changes in the tonnage added or deleted to the blend or from any one source. Other rules would be needed to determine which quality to improve if two or more are out of spec. At this level, the process of building the knowledge base provides the engineer with a deeper understanding of his or her own thought processes. The advantage of obtaining better blends is clear for this approach. Two more advantages should also be apparent. One is that it follows the same common sense logic that is used when doing the blends by hand or by spreadsheet, making it easy to understand. The other is that, like the search procedure, it designs the blend rather than just analyzing manually designed blends. Thus, it has all the good features of both approaches discussed thus far while providing improved results over each. A final advantage is the ease of use and ease of development. The expert system shells that are on the market are very easy to use and can be run on microcomputers. Linear programming Linear programming is an algebraic tool that solves a set of linear equations to yield an optimal solution to a problem. The optimal solution is based on the linear model so the results are only as good as the ability of the linear model to accurately portray the reality of the problem situation. It is fortunate for the coal blending problem that a linear model can be devel¬oped that reflects exactly the problem that is required. Unfortunately, the mining industry has been slow to use this tool. Coal blending applications available that use linear programming take one of three forms. The first, requiring exper-

Jan 12, 1988

By John A. Breslin

Control of radiation hazards in mines is only one of many goals of the Bureau of Mines. Radiation research is only a small part of the Bureau's mine health and safety research program. In this paper I will describe the mission and programs of the entire Bureau of Mines, with emphasis on the mine health and safety program of which our radiation research is a part. The radiation program and its results will be described in detail by other speakers during this symposium. The Bureau of Mines was established in 1910 and is one of a number of agencies within the Department of Interior. Our mission is given by the Organic Act of the Bureau of Mines, last revised in 1913, which still accurately describes our work today. The amended Organic Act (Public Law 62-386) gives the Bureau authority "... to conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste in the mining, quarrying, metallurgical, and other mineral industries; to inquire into the economic conditions affecting these industries..." Since 1913 at least 52 public laws bearing on Bureau responsibilities have come into force. However, our basic role is still unchanged, i.e. improving health conditions, and increasing safety and efficiency in the mineral industries. The two principal activities of the Bureau are Minerals Information and Analysis and Minerals Research. The Minerals Information and Analysis programs provide the data base and the analytical capability to support the development of effective national mineral policies. Data on the availability, production, and utilization of minerals are collected, interpreted, and analyzed for some 100 commodities. Resources of the most important commodities are evaluated to support policymaking that influences utilization of the Nation's existing and potential mineral supplies. The President's budget for the Mineral Information and Analysis programs in fiscal year 1982 is $34 million. The largest activity of the Bureau is Minerals Research, which is divided into three major programs: Mineral Resources Technology, Minerals Environmental Technology, and Minerals Health and Safety Technology. The principal goal of the Mineral Resources Technology program is to help provide technology to maintain an adequate supply of minerals for the United States. The budget requested by the President for this program in fiscal year 1982 is $41 million. The goal of the Minerals Environmental Technology Program is to create mining and mineral processing operations that are more compatible with the environment. The budget for this program in fiscal year 1982 is $12 million. The largest program of the Bureau is Minerals Health and Safety Technology, which has the goal of providing the technology to protect the health and safety of mine workers. The budget for health and safety research for fiscal year 1982 is $55 million. Our radiation research is part of the health and safety research program. The Bureau of Mines has done research to improve health and safety conditions in mines since it was established in 1910. The research expanded greatly following the passage of the Federal Coal Mine Health and Safety Act of 1969 (Public Law 91-173) and the Federal Mine Safety and Health Amendments Act of 1977 (Public Law 95-164). These acts provided for increased health and safety regulatory activities, but they also significantly increased the funding available for mine health and safety research by the Bureau of Mines. Funding for the Bureau's health and safety research grew from $12 million in 1970 to $60 million in 1981. The funding in 1982 will be somewhat lower than that for 1981. However, the health and safety program funding is still approximately 40 percent of the total budget of the Bureau of Mines. Of the health and safety budget, 22 percent is spent on research to control health hazards in mines, including radiation hazards, which has a budget in 1982 of approximately $1.1 million. Other mine health hazards which the Bureau is doing research to control include respirable mine dusts which cause black lung and silicosis; excessive noise; toxic gases from explosives and diesel emissions; and excessive heat in deep hot mines. The other 78 percent of the budget is spent on safety research to prevent death and injury to miners from such causes as roof falls, fires, explosions, and accidents involving mining equipment. Over the past decade the majority of the Bureau's health and safety research has been done through outside contracts with private industry and universities. Our policy has been to do some research inhouse to maintain the expertise of Bureau personnel. Contractors are used to do research for which the Bureau does not have the necessary personnel available. The percentage of the program being done by contract has been gradually declining for the past few years, and in 1982 the program will be divided evenly between inhouse and contract research. The inhouse research of the Bureau is done at the 10 research centers located throughout the country. Our radiation research is done at three research centers, Denver, Spokane and Pittsburgh, and by contractors whose work is monitored by project officers at these centers. There are three Federal agencies involved in mine health and safety. These are the Bureau of Mines, the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and

Jan 1, 1981