Search Documents

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

By J. G. Clevenger

Introduction Computer-based haul truck dispatching has been operational at Tyrone since May, 1980. The system, known as Dispatch, has accomplished significant productivity gains compared with the former method of manual radio dispatching. These gains translate into a reduction in equipment requirements or an increase in production. An operational mine may choose to increase production or reduce the number of equipment shifts operated, resulting in substantial operating savings. Dispatch Description The core of Dispatch is a VAX 11/780 computer. Originally purchased with 512 kbytes of memory, the system is now upgraded to 3.75 Mbytes to accommodate users from all areas of the operation. Dispatch alone requires 200 kbytes of locked-in memory, with an additional 300 kbytes of memory available on a top priority basis. The computer, located in the Tyrone Branch general office building, is connected by under-ground cables to the dispatch tower, 3.2 km (2 miles) from the general office. Four two-paired lines are used to drive two cathode ray tubes, a printer, and the Dispatch master panel. One CRT continuously displays pertinent pit information for the dispatcher's use. Routinely displayed transactions include truck assignments, changes in shovel material type, truck and shovel breakdowns and delays, and changes in truck, shovel, or dump status. Er¬ror detection capabilities include late arrival and improper input from the field panels. The second display terminal is used for utility reporting and input functions. Status reports are displayed for availability, position, and material type being handled by any given truck or shovel. Fuel reports are available indicating the time last fueled, quantity of fuel delivered, and the time spent fueling. A truck factor utility reports relative performance to other trucks and a shovel utility reports efficiencies in tons per shovel shift. Instantaneous shift reports and mine status reports are available. Inputs such as lineups, operator changes, new travel times, shovel bias, tie down times, and lunch times are all handled with the utility display terminal. The printer records a hard copy of operating truck locations and production from the beginning of each shift. If there is a system malfunction, the printer copy is readily available to the foreman for radio dispatching. The Dispatch master panel is a microprocessor-based panel that allows the dispatcher to override any computer-assigned transaction. Classification of "bad order" conditions and acceptance of certain field messages is entered through the master panel. This panel communicates with all truck and shovel field panels via UH radio frequency through a repeater tower located on a high ridge contiguous to the mining area. Each truck and shovel field panel unit transmits a coded signal that is identified by the computer. A typical communication sequence between field panels and the computer for one complete truck cycle is: • The truck panel LED display indicates the shovel number to which it is assigned. The truck arrives at its assigned shovel and the operator presses the "Arrive" button on the truck panel. As the computer receives the "Arrive" message, it concludes the return (empty) travel time and begins accumulating idle time before loading. • When the first dipper of muck is placed into the bed of the truck, the operator presses the "Load" button. The computer concludes the truck idle time accumulation and begins the loading time calculation. • When the truck is loaded, the shovel operator presses the "OK"

Jan 9, 1983

By E. De Souza, H. Heidrich

In underground operations the evaluation of blasting fume dilution times and the application of recirculation techniques require accurate determination of the concentration of toxic fumes produced by the explosive used. This paper describes a methodology for obtaining concentrations of detonation products from commercial explosives tested under typical rock confinement and looks into the development of techniques for reducing toxic gases produced by explosives. This paper also analyses the application of techniques for the removal of toxic gas which would enable reduced re-entry times, a reduction in the quantity of fresh air and the use of air recirculation techniques, thereby providing substantial economic benefits to the industry. INTRODUCTION Toxic fumes from blasting operations are among the most common and serious hazards encountered underground. The implication of high concentrations of toxic gases emitted from blasting on the mine ventilation system are very significant and, in many cases, catastrophic results have occurred. Because blasting is a routine practice underground, the mining engineer is always confronted with the problem of controlling the fumes within acceptable levels. Typical control procedures employed underground include preventing or reducing the amount of fumes liberated from blasting through the proper selection of explosives and proper blasting techniques; removing the fumes through local exhaust systems or auxiliary ventilation (dilution ventilation); blasting off-shift, or at restricted times; localizing or isolating the effects of blasting where workings are isolated or sectionalized in the ventilation system; and absorbing some of the components of the fumes using air-water sprays. Dilution is one of the most effective control measures against blasting fumes and is universally applied. However, for precise determination of the dilution times for the fumes to reach safe concentrations, accurate determination of the concentration of toxic fumes produced by the explosives used is required. Research work has been carried out in determining the types and volumes of gases produced from blasting. In the case of ideal detonations, the nature and quantity of the fumes produced can be predicted by thermo-hydrodynamic calculations. However, commercial explosives exhibit non-ideal behaviour which is enhanced by the relatively small diameters of application in underground mines. The confinement offered by the surrounding rock further complicates the situation. It is well recognized that confinement affects performance and consequently fume generation. A detailed data base of fumes generated by commercial explosives at various conditions is introduced and the effect of blasting parameters such as, confinement, shock desensitization and incomplete detonations on toxic fume production is described for a variety of commercial explosives in use today. Thermodynamic predictions on fume production by the explosive compositions tested are also presented and compared with experimental results and their significance in assessing the quantity of fumes produced is discussed. A mathematical model capable of determining dilution ventilation requirements and dilution times to reduce the fume concentrations in the blasting zone to acceptable levels has been developed and it is being incorporated into a network system so that the effects of blasting can be simulated in typical mine ventilation systems. Solutions to the problem of controlling blast fumes within acceptable levels are described. These solutions include the use of control procedures which prevent and reduce the amount of fumes liberated from blasting. The use of low fume explosives, proper blasting techniques, dilution ventilation and filtration can be combined to effectively control fume production and save on costs. The application of these techniques to enable recirculation of underground air with reduced quantities of fresh air requirements is evaluated in a case study.

Jan 1, 1993

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: • The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. • That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. • Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equip¬ment, blasting, or water infusion. • To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. • As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. • When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in. - diam). The techniques in detail are somewhat complex and sub¬ject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1989

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equipment, blasting, or water infusion. To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in.- diam). The techniques in detail are somewhat complex and subject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1990

By Charles H. Jacoby

Introduction Although, in general, the openings created in domes or diapiric type salt deposits during mining operations are larger than those created in bedded deposits, the openings in bedded salts are of significant lateral extent. Thus, this paper will deal primarily with the dome deposits of the Gulf Coast and more specifically with the Avery Island dome operated by the International Salt Company where recent development activities have materially increased the sizes of previously standard openings. Geology The geology of salt deposits is the governing factor in the rock mechanics associated with the opening which is being created in the salt. Bedded salts are customarily characterized by having experienced solution along the interface between the top of the salt and the overlying bed. Thus, as the salt slowly dissolves there has been left behind a layer of laminated insolubles which is often incompetent. In most cases, this incompetent rock must be supported by a thickness of bedded salt which is left in the roof as support. Where this salt is of secondary deposition (recrystallized halite) with included moisture, additional thicknesses of roof salt are necessary to achieve stability. The salt which forms the domes of the Gulf Coast regions is from the Louann formation of the Jurassic period. These formations are dipping toward the Gulf of Mexico so that the upper tier of domes which have formed across northern Louisiana in an east-west direction into Mississippi and Texas have a salt source some 10 to 15,000 feet

Jan 1, 1976

By A. Zorychta, T. Cyrul, Z. Kleczek

INTRODUCTION Underground mining causes disturbances of the primary state of stresses. Resulting from those disturbances a loss of stability of rocks that surround excavation may occur interrupting the production and creating life danger for the personnel. One of the manifestations of such an instability is a rock burst phenomenon which mainly occurs at great depths. From the mechanical mint of view the rock burst is a loss of stability /Filcek et a1.,1984; Pietuchow and Linkow, 1976/ due to : - quasi-static stress changes in the surrounding rocks; we will call it s seam burst , - dynamic stress changes in the surrounding rocks caused by rock shocks ; we will call it roof burst. Possibility of the rock burst occurrence Is uniquely determined by the state of stresses existing in the rock mass. In the following sections of the paper we will consider different aspects of this question. Moreover distributions of displacements and failure criteria for a coal seam at longwall mining will be defined. STATEMENT OF THE PROBLEM Determination of the vertical stresses and displacements resulting from longwail mining will be based on the Budryk’s idea of a stress wave /Salustowicz, 1955/. The idea originates from the analysis of a roof plate /beam/ resting on the deformable foundation /Sean/ and subjected to the cylindrical bending. Equation of the bending lice uniquely defines vertical stresses and displacements which are induced in the seam. The equation will account only the shear force effect. Elimination of the bending moment has been shown and discussed by Zorychta and Bcrecki /Zorychta, 1985; Borecki and

Jan 1, 1986

By L. G. Tejada, T. Sjursen

In the production of ferronickel at Falconbridge Dominicana's plant in the Dominican Republic the Reduction Plant plays a vital role by partially reducing the nickeliferous oxide ore, and pre- heating the charge to the electric furnaces. Ore is agglomerated in the form of pillow-shaped briquettes which are screened and fed to 12 open-top shaft furnaces. Hot (over 1250°C) reducing gases are partially cooled (less than 1150°C) and introduced through a set of primary tuyeres. The reducing gas rises counter-currently to the flow of solids. A portion of the partially spent reducing gas is withdrawn at the furnace top and recirculated through a set of secondary tuyeres, 1800 nrm above the primary tuyeres. Together with the recycle gas a controlled amount of air is also added to react with the partially spent reducing gas in order to preheat and dry the charge in the upper part of the shaft furnaces. The calcine is discharged through three discharge legs and pusher block assemblies into open-top refractory lined cars. These cars are then hauled to the electric furnace, parked over selected feed ports, and discharged through bottom gates. The furnace exhaust gas is de-dusted in cyclones and then passed through Venturi scrubbers. The slurry is fed to a thickener, filtered, and recycled to the ore receiving hopper in the ore preparation area. Dust generated throughout the plant is collected, wetted to conform with briquette press feed, and recirculated in a controlled manner through the feed system.

Jan 1, 1979

By K. S. E. Forssberg, M. I. Hallin

In many cases, the reuse of process water in flotation plants is desirable both for plant operating reasons and for environmental protection. The main advantages are better housekeeping of fresh water and process chemicals together with the reduction of polluting species to the environment. There are however a number of problems involved in the use of recycled process water. The main problem is that recycling sometimes has a deterious effect on the process and can occur months after the start of water recycling. The Division of Mineral Processing of Luleå University of Technology has been conducting experiments on recycling of process water at various sulphide plants in Sweden for over ten years. The experiments have been carried out in pilot- and full industial scale, in collaboration with the mining companies operating the plants. Until 1988 investigations were carried out in four different sulphide plants. The objectives of the experiments were: first to document differences in the composition of the process water during recycling; secondly to investigate any changes in the pulp chemistry of the flotation circuits wich may be due to the influence of recycled water; and lastly to establish critical levels, if any. of the parameters measured. While conducting experiments of this kind several things have to be kept in mind. Normally, recycling is done by using tailings pond water as process water. This means that time effects are important, because of the time lag between water input in the tailings pond and the reclaim of that water back to the plant. As will be shown, the

Jan 1, 1989

By James Warren Andrews, Philip C. Nyberg

The regulation of exposure of underground personnel to radon and its daughter products has significantly changed since the 1950's. The U.S. Bureau of Mines - Mining Enforcement and Safety Administration (MESA) - Mine Safety and Health Administration (MSHA) sequence of standards and regulations have lowered the maximum allowable occupational exposure and now the new Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants, effective in 1990, have further regulated uranium mine emissions. Under the authority of Section 112 of the Clean Air Act (42 U.S.C. 7401), the EPA has set regulations for the control of radon (Rn-222) emissions from underground uranium mines as well as other sources. Since the venting of radon from the mine atmosphere to the outside air is a major component of the miner's protection, and since this is the first quantitative effort to limit gaseous mine emissions to the environment, it was felt that it would be useful to examine the implementation of the EPA regulation at working mines. The concern was not only for determining compliance with the regulation but also for observing what effect the rule might have on mine air quality and thus on worker exposure. The regulation is stated in terms of the maximum permitted radiation dose to the closest potentially exposed individual, which is calculated from a computer program supplied by EPA and radon emission rates measured by the mine operator. Relative proximity to nearby populations determines the allowable magnitude of mine exhaust ventilation emissions. For some mines this is a serious operational constraint.

Jan 1, 1991

By S. B. Leonov, K. I. Popov, S. B. Polonsky

The offered technological line includes a flotation pulp air conditioner operating on the impact-mechanical effect and two column apparatuses with a descending pulp-air flow mounted in series. The technology developed makes it possible to increase considerably the valuable component in the concentrate simultaneously with a reduction in energy consumption for the flotation process. The experience achieved with the technology showed the possibility for obtaining sulphide silver-bearing ore superconcentrates with the noble metal content 2-10 times higher than that in the concentrates obtained by the conventional technology. The same results were obtained in the process of calcium-bearing boron-silicate ore-dressing.

Jan 1, 1995

By R. Hogg

The various sub-processes which, together, make up the unit operation of froth flotation all depend on the characteristics of the feed solids, the solution phase, the air bubbles and the mechanical/hydrodynamic action of the machine. Characterization is obviously necessary for evaluation and process control, but the relationships between characteristics and process response are often unclear. A model-based characterization scheme is proposed in which material and system characteristics are evaluated in the context of simplified models for the individual subprocesses. The general basis for such an approach is discussed using the process of particle attachment and the influence of mineral liberation as examples.

Jan 1, 1989

By J. M. Rotter, R. A. Lohnes, J. Y. Ooi

Reliable prediction of wall pressures in a coal silo demands careful characterization of the stress-strain properties of the coal. This paper describes the results of triaxial compression tests on a typical fine-ground coal used in power generation and describes the fitting of several different constitutive models to the data. The fitted parameters for the constitutive models are well suited to application infinite element analyses. The different models are used to give the reader flexibility in choosing a model and to show the shortcomings of some models. To explore the quality of the fitting process, the fitted results are compared with finite element predictions of the triaxial test itself.

Jan 1, 1998

By T. E. Wilson

The length of Alaska's coastline, combined with the presence of a significant number of fjords, encourages consideration of marine disposal of mine tailings. However, the decision-making process is complex because various factors govern the viability of the submarine tailings disposal (STD) option. An expert system, called the Submarine Tailings Disposal Expert System (STADES), was developed to help mining project planners explore the feasibility of STD. A review of the existing literature, supplemented by engineering recommendations, on the various aspects of the marine disposal of tailings formed the knowledge base for the expert system. The shell used to develop the expert system was LEVELS.

Jan 1, 2003

By Lynn Huntsman

INTRODUCTION The Sunnyside mines of Kaiser Steel Corp. are lo¬cated on the west flank of the Book Cliff Range, a tongue of the Wasatch mountain range in Utah. The mines are 193.12 air km (120 air miles) southeast of Salt Lake City and 40.23 km (25 miles) east of the town of Price. The area has a semiarid climate with an an¬nual rainfall of 304.8 to 381 mm (12 to 15 in.) and a temperature range of -23.3 to 32.2°C (-10 to 90°F). The base of the Book Cliff Range is approximately 1981 m (6500 ft) in elevation with some mountain peaks in excess of 3048 m (10,000 ft) (Fig. 1). The Sunnyside mines were opened in the late 1890s and have been operated continuously since that time. Kaiser Steel leased the No. 2 mine in 1942 and pur¬chased the entire property in 1950. There are three mines adjacent to one another, each with its separate access, ventilation, and haulage. The three mines en¬compass an area extending 12.87 km (8 miles) along the outcrop and dipping northeasterly 2.41 to 3.22 km (11/z to 2 miles) into the Book Cliffs. During 1975, only the No. I and No. 3 mines were operating to sup¬ply 908 184.7 t/a (1,000,000+ stpy) of clean coal to the Kaiser Steel mill at Fontana, CA. Sunnyside coal is blended with coal from the Kaiser Steel mine near Raton, NM, and with purchased coal from noncompany sources to form the mix for the coke ovens. At that time, Sunnyside operated three longwall units and five to seven continuous miner units. Typical production for that time came from one miner unit pillaring an area not conducive to longwall mining; one or two miner units on construction or modernization projects, and the remaining units used to develop future longwall panels. Longwall mining has been a part of the Sunnyside scene since 1961 when the first panel was set up in the lower Sunnyside seam of the No. 3 mine. Through 1975, 27 longwall panels were mined (Fig. 2). Of the more than 47 173 604 t (52,000,000 st) of clean coal that were taken from the property through 1975, 6 350 292.9 t (7,000,000 st) were mined by longwall methods. Coal was brought to the surface in 4.5-t (5-st) mine cars and crushed to -152.4 mm (-6 in.) before entering the preparation plant. Coarse coal is cleaned by Baum jigs and fine coal (-28 mesh) is cleaned in flotation cells. The coal is reduced to 50.8 x 0 mm (2 x 0 in.) and belted to an aboveground storage pile with a ca¬pacity of approximately 113 398.1 t (125,000 st). The coal is gravity fed through two 1.52-m (5-ft) diam culverts directly into railroad cars, which pass beneath the storage pile through an arched excavation. Eighty-four 90.7-t (100-st) cars make up a unit train which makes the round trip to the steel mill in four days. Additional trains are scheduled in as demands dictate. Loading rates in excess of 13 607.8 t/h (15,000 stph) have been attained. Geology The coal seams of this area are of Cretaceous age and are classed as a medium volatile bituminous coal. coal, with a sulfur content less than 1 % and 6 to (20-mile) zone of the Book Cliffs, and this area is owned or under lease by either Kaiser Steel or US Steel. Coal in adjacent areas is noncoking but an excellent steam coal, with a sulfur content of less than 1 % and 6 to 7% ash. Sunnyside coal contains 40% volatile, 53% carbon, less than 1 % sulfur, and 51/2 to 61/2 % ash after washing. There are two minable seams throughout most of the Sunnyside property known locally as the upper and lower Sunnyside. Separation between the seams varies from less than 300 mm (1 ft) near the southern boundary adjacent to the US Steel Columbia mine, to over 12.19 m (40 ft) in areas of the No. 3 mine in the center of the Sunnyside property. The upper seam varies in height from 1.2 to 1.98 m (4 to 61/2 ft) while the lower seam varies in height from 1.52 to 4.28 m (5 to 14 ft) in areas of No. I mine where the two seams apparently come together. The majority of early work was con¬centrated in the upper seam which has a stronger roof and a lower sulfur content. When Kaiser Steel began mining the No. 3 mine in the early 1950s, it mined in the lower seam beneath the old workings with conven¬tional and continuous mining equipment. Numerous bounces and pressure points created by unextracted pillars and barriers in the upper seam made this a low¬production, high-cost mine and brought about the ad¬vent of the first longwall system. The first unit, while small by today's standards, successfully mined panels that had been all but given up and saved the mine from closure. There were areas that could not even be mined by longwall because of the erratic extraction in the upper seam. The system was successful enough to allow operations to gain access to and develop virgin areas of the upper seam. Development of longwall mining in the No. 3 mine has been confined to the upper seam since late 1964. With the almost complete extraction afforded by the longwall system, it is felt the lower seam can be successfully worked in future years (Fig. 3). In most of No. 1 mine, only the lower seam (or lower seam and upper seam combined) is minable, except in the northwest portion where a rock split has again separated the seam into two 1.83 to 2.13-m (6 to 7-ft) thick beds. In this area, the upper seam or upper split is being mined. The separation between seams at the present workings in this area varies from 0.609 to 6.1 m (2 to 20 ft). It is hoped that most of the lower split can be mined using shield supports and/or what¬ever new technology is developed in the coming years. The coal seams in this area dip to the northeast at an average grade of 10%. The dip near the outcrop reaches 22% and gradually decreases downdip. Over¬burden ranges from a few meters at the outcrop to 762 m (2500 ft) over some of the deeper workings. In the next several years, some overburden will be in excess of 914 m (3000 ft) as the lower mine workings extend ever deeper under the Book Cliffs. To cope with the

Jan 1, 1982

By Joseph W. Murray

GENERAL DESCRIPTION The undercut-and-fill method of mining was devel¬oped by Inco Ltd. in the Sudbury district of Ontario, Canada, to deal with abnormal ground conditions en¬countered in pillar recovery. Although it is now some¬times utilized as a primary stoping method, the main application continues to be in pillar recovery. In any mining method in which fill is employed, pillar systems tend to fail gradually as stoping pro¬gresses. As a result, most pillars are completely destressed and broken by the time pillar recovery com¬mences. Control of the back in such ground becomes a major problem and is contingent on local conditions as they exist in the workplace. In most mining methods, operations such as drilling, blasting, slushing, and tim¬bering can be readily assessed and the mining cycle pre¬dicted. However, in the mining of pillars with overhand methods, the time and effort required to maintain a safe back varies to a quite unpredictable extent. For years the square-set method was the most effective means available for pillar recovery. However, in areas where bad ground was encountered, square setting was a costly and sometimes hazardous method. As the tonnage mined from pillars increased, it was apparent that a safer and less expensive approach was required. Past experience indicated that the best way to deal with broken ground was to mine from the top down. Top slicing systems were examined but were rejected due to the major sub¬sidence which resulted. However, ideas generated from studying top slicing finally developed into the present method of undercut-and-fill. This method, which has almost completely replaced square-set mining, exhibits reduced costs, has improved safety and efficiency, elimi¬nates the factor of bad ground overhead, and allows a closer prediction of the actual mining cycle. The result is more accurate scheduling of pillar production. This factor is of increasing importance as the tonnage from pillar recovery increases in relation to total mine pro¬duction. Undercut-and-fill is a method of extracting a block of ore by mining successive cuts, working from the top down. After a cut of ore is completely mined out, lami¬nated timber stringers are constructed along the sides for the full length of the cut. Round logs covered by a wire screen are laid across the stringers to form a mat. The cut is then tightly filled with hydraulically placed cemented sand fill. Mining is then resumed on the cut immediately below the mat. As the cut advances, the timber stringers are supported by round timber posts seated on the solid bottom of the cut. Drilling, blasting, muck removal, and timbering operations are repeated until all the ore in the cut has been removed. At this time, another log mat is laid and the cut is filled. This sequence is continued until the block has been mined from level to level. The basic principles of undercut-and-fill can be adapted to a variety of mining situations. It can be applied transversely or longitudinally in ore bodies of varying width, that dip from vertical to flat lying. The method can be applied using conventional equipment or it can be mechanized through the introduction of small diesel or air-powered units for muck removal. Undercut¬and-fill is a selective method, ore recovery is high, and dilution can be controlled to an acceptable level. How¬ever, it is a high-cost, labor-intensive method and as such its use is restricted to areas where the less costly meth¬ods of ground support are not successful or where bulk mining methods are not adaptable. One basic require¬ment for undercut-and-fill is an adequate source of hydraulically placed cemented sand fill and a dependable sand plant and distribution system. The success of the undercut method is to a large degree dependent on the competence of the fill placed in each of the successive cuts. In theory, the weight of the fill on each cut is supported in part by the cemented sand itself as it binds to the rough sides of the mined¬out areas next to the pillar walls, and in part by the tim¬ber support. As mining progresses beneath the mat, a downward pressure is exerted within the cemented fill and a voussoir arch develops above the mat, across the full width of the cut. This supports the major portion of the load. The log mat and posts have a double func¬tion in that they carry the remaining weight not sup¬ported by the voussoir arch and in addition prevent any pronounced settling of the fill mass. Excessive settling breaks the bond between the cemented fill and the pillar walls, eliminating the arch effect and transferring the entire load to the mat and posts. The theory of a voussoir arch forming within the cemented sand fill mass is substantiated in practice by the fact that pillars have been mined from level to level with no more significant weight on the bottom cuts than was experienced on the top cuts. In effect, as mining progresses downward, there is no additional transfer of weight from previous cuts to the cut being mined. APPLICATION OF UNDERCUT-AND-FILL Because of their size, the Sudbury ore bodies are, for the most part, mined transversely and, to a considerable extent, by filling methods. Transverse stoping blocks are designed with 9-m (30-ft) crown pillars established be¬low each level and with stopes separated by vertical rib pillars. In past years, floor pillars were left above the level as well, but present practice favors the silling of primary stopes at the base of the rail. Rib pillars are designed to meet the ground control requirements of the primary stoping methods. Local conditions and past experience generally dictate their size. Historically, since the square-set method was to be used for recovery, rib pillars were designed to accommo¬date standard 1.7-m (5'h-ft) sets. A typical rib pillar is four sets wide [6.7 m (22 ft)] when located between two square-set or cut-and-fill stopes having a width of 8.4 m (27.5 ft). When the undercut-and-fill method was de¬veloped, a mat width of two sets was adopted. This di¬vided each cut of the common four-set pillar into two

Jan 1, 1982

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

By B. Qiu, Y. Luo

The design of the predriven recovery room is not an easy task, because the stress distribution in the barrier pillar, standing supports, fender pillar and the immediate roof is changing as the longwall face approaches the predriven recovery room. An analytical approach is proposed to determine the stress distribution in the barrier pillars, fender pillars, standing supports and immediate roof of the recovery room based on the fracture mechanics approach. Based on the developed mathematical model, a stand-alone computer program has been developed to facilitate the required computations. The parameters such as overburden depth, recovery room width, mining height, shield and standing support capacities are incorporated into this program to access the feasibilities of predriven recovery room designs. Compared to the finite element method previously employed, this analytical approach offers the same, if not better, accuracy without requiring expensive computer hardware and software or specialized expertise.

Jan 1, 2012