Search Documents

By D. W. Hutchinson

One of the most important problems facing the coal industry today is the disposal of refuse from the coal preparation plants in a safe, economical, and efficient manner while complying with all legal requirements. The most commonly used refuse disposal method has been landfill/impoundment. In this method, the coarser refuse fractions are disposed of by layering and compaction into a landfill. The fine coal slurry refuse fraction is impounded in a dam constructed of a portion or all of the coarser refuse fractions. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the preparation, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. At the time of the promulgation of the new Federal regulations, United States Steel Corporation was in the process of designing the Cumberland preparation plant. As a result of the new regulations

Jan 1, 1977

By M. Boucraut

After stating the advantages of the magnetic roasting technique as applied to iron ores, the authors report on technological research by I R S I D * in the field of magnetic roasting in fluid-bed furnaces This investigation was conducted first on an experimental two stage fluid-bed furnace which processed permanently 100-200 kg/h of ore, then on a three stage fluid-bed furnace with 1-2 t/h working capacity and at last on a 250 t/day pilot furnace The specific features of the IRSID process comprise - on the one hand, using special burners in the roasting reactor thereby ensuring a high production rate of the furnace - on the other hand, using a heat-exchanger where the preheating and cooling stages of fluidized ore are associated, so as to allow an efficient and simple cooling of both roasted ore and waste gases flowing out of the roasting reactor, thereby supplying heat to the crude ore and combustion air for the reactor burners Starting in 1965 the operation of the 250 t/day pilot plant at the Bazailles mine gave IRSID the opportunity of improving the conveying appliances and adapting them to the process, while perfectly confirming the metallurgical results obtained under ideal laboratory conditions

Jan 1, 1968

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

This paper combines theoretical and experimental analysis to conduct relevant research to improve the accuracy of predicting paste yield stress by slump flow. The analytical model of slump flow for yield stress is derived based on a mini-cylindrical mold with a height-to-diameter ratio of 1. It shows that the dimensionless slump flow is a monotonic decreasing function of the dimensionless yield stress and is independent of the material type (specific gravity), which provides a theoretical basis for quantifying the rheological properties of paste with slump flow. Three different tailing-prepared pastes were tested for their slump flow and implemented rheological tests simultaneously. The yield stress is obtained based on the Bingham model fit, as the measured value of the yield stress is substituted into the derived theoretical model. The studied pastes yield stresses range from 34.78 to 524.08 Pa, with corresponding dimensionless slump flow of 3.43 to 1.09. The results showed that the calculated slump flows were generally greater than the measured values. The analysis showed that this was mainly due to the thixotropy of the paste, with minor deviations ranging from − 1.5 to 5.8% for the less thixotropic pasted prepared from tailing C. An approximate analytical solution for yield stress as a function of slump flow is obtained using Taylor’s formula. However, it is unsuitable for predicting the yield stress because the yield stress calculated by this function is much higher than the measured value. The empirical yield stress model was constructed and experimentally verified. The results show that the empirical formula has high accuracy and good generality. The deviation of the studied pastes is between − 15 and 5%, which provides a practical method for rapid and accurate prediction of paste yield stress in mine sites.

Jun 1, 2023

By R. Krog, M. Valente, R. Ochsner, W. Marchewka, R. Jensen, R. K. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine for analysis and display on the surface. The U.S. National Institute for Occupational Safety and Health (NIOSH), in collaboration with Signal Peak Energy (SPE), LLC, Bull Mountains No. 1 Mine, operated a TBS during mining of two bleederless, longwall panels. This paper describes the gas analysis data and its interpretation. As verified by the TBS, coal at the SPE mine tends to oxidize slowly. It was known that a reservoir of low-oxygen concentration atmosphere developed about 610 m (2,000 ft) behind the longwall face. A bleederless ventilation system facilitates formation of an inert atmosphere in this longwall gob and decreases the likelihood of spontaneous combustion. Connections of the mine atmosphere to the surface through subsidence cracks could allow airflow into the longwall gob, revive coal oxidation and increase spontaneous combustion risk. The atmospheric composition of the sealed areas was homogeneous, except in the immediate vicinity of suspected ingassing points. The TBS verified that gases within the partially sealed, bleederless longwall gob expanded into the longwall tailgate area when barometric pressure decreased. The concentration of carbon dioxide in the back return airflow at the longwall tailgate was observed to increase by a factor of three and possibly up to 10 times the typical background concentration of 0.5 to 1.0%, depending on the size of the longwall gob and the magnitude of barometric pressure decrease. TBS have the inherent disadvantage of slow response time due to travel time of the gas samples and sequential gas analyses. A TBS or similar continuous monitoring system could be beneficial in detecting and providing warning of potentially hazardous gas concentrations, if the slow response time of the system is always understood.

Jan 1, 2013

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"The Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million people. The project was constructed by a joint venture (JV) of four South American contractors and consisted of the following key components:• Treatment plant: A 16-ha (39-acre) area was cleared for the construction of a treatment plant to purify 900,000 m3/day (1.2 million cu ft/d) of raw water from the Paraná River and distribute it to the surrounding communities.• Bored tunnel: Nearly 15 km (9 miles) of 3.6 m (12 ft) inner diameter tunnel, ranging from 18 to 22 m (59 ft to 72 ft) below grade, was bored with two earth pressure balance (EPB) tunnel boring machines (TBM) to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions. Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access and ventilation shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (intake and treatment plant, respectively) and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installedafterward."

Sep 1, 2016

By Justin Carl, Aliuddin Mohammad, Gordon Evans, Steven Bealby, Carlton Ray

"The District of Columbia Water and Sewer Authority (DC Water) is implementing the $2.2-billion DC Clean Rivers Project (DCCR) to control combined sewer overflows (CSO) to the Anacostia and Potomac rivers and Rock Creek, and to provide flood relief to the Bloomingdale and LeDroit Park neighborhoods in the District of Columbia. The long-term control plan complies with the requirements of a Federal Consent Decree entered into by DC Water, the District of Columbia and the United States, as represented by the U.S. Environmental Protection Agency and the Department of Justice. The Northeast Boundary Tunnel, a design-build project, will store combined sewage and deliver it to a system of downstream tunnels and ultimately to the Blue Plains Advanced Wastewater Treatment Plant (Blue Plains), where it will be treated. In addition, the Northeast Boundary Tunnel (NEBT) is a major project associated with the mayor’s task force to alleviate extreme flood events in Bloomingdale and LeDroit Park. The Northeast Boundary Tunnel Utility Relocations (NEBTUR) design-bid-build (DBB) project is an accelerated component of the Anacostia River System, as shown in Fig. 1. During dry weather conditions, the entirety of the sewage in the combined system is conveyed to Blue Plains.During storm events, when sewer pipe capacity is exceeded, the flow, which is a mixture of sewage and stormwater runoff, overflows into receiving waters through outfalls. There are a total of 47 active CSO outfalls along district waterways.The influx of storm runoff into the combined sewer has an additional impact on the communities of Bloomingdale and LeDroit Park. The sewer system is outdated and undersized. In these neighborhoods, when the capacity of the sewer is exceeded, localized flooding occurs and backups into adjacent residences are prevalent. In any given year, there is a 50-percent chance that flooding will occur in these neighborhoods."

Jan 9, 2017

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By Wei Li

Carbothermic reduction kinetics of ilmenite concentrates catalyzed by sodium chloride and the microwaveabsorbing characteristics of the resulting reductive products were investigated; the reduction degree of the reaction was deduced to be . Results show that the activation energy is 112.03 kJ/ mol when NaCl is used as catalyst, lowering to 23.11 kJ/mol for the final stage activation energy using sodium silicate as a catalyst. There is a sharp change in the reduction rate constant at temperature ranges of 1,223 K - 1,273 K and 1,373 K - 1,423 K. Microwave-absorbing characteristics of reductive products were measured by the method of microwave cavity perturbation. It was found that microwave-absorbing characteristics of reductive products obtained at temperatures of 850° C, 1,100° C and 1,150° C show sharp changes. Through X-ray diffraction (XRD) characterization, it was found that the formation of Fe occurs at a temperature of 900° C during the reduction process of ilmenite concentrate. The decrease of FeTiO3 content results in the decrease of microwave-absorbing characteristics, while the increase of Fe content gives rise to the increase of microwaveabsorbing characteristics. The decreasing trend is larger than the increasing trend, which is the main reason for the sharp changes in the microwave-absorbing characteristics of reductive products at the temperature range of 850° C to 900° C. When the decreasing trend is smaller than the increasing trend, it becomes the main reason for the sharp changes in microwave-absorbing characteristics of reductive products at the temperature range of 1,100° C to 1,150° C. Kinetics results show that sodium chloride can catalyze the carbothermic reduction of ilmenite, and microwave-absorbing characteristic investigations indicate that microwave heating can be used in the carbothermic reduction of ilmenite.

By J. E. Brownhill

This paper does not deal with the typical start-up issues of equipment, production capacity or work force. This is a description of the challenges faced and the changes made by the project team to bring to fruition the reconstruction of Port Inland. Many honored traditions and norms had to be overturned to find the winning combination that provided the productivity, flexibility and cost necessary to survive in today's competitive minerals environment. This paper covers the innovation in terms of machinery, operations, and management philosophy that permitted the renovation and reopening of Port Inland as a commercial limestone producer in the spring of 1992. Port Inland, constructed by Inland Steel in 1930, operated as a captive source of metallurgical grade limestone for the steel industry until its closure in 1989. Located in the Upper Peninsula of Michigan on the north edge of Lake Michigan, the operations consist of a deep water port facility with crushing, screening and stockpile storage for 500,000 tons of finished product at the port. Ninety-nine percent of the stone is shipped via lake boat to ports within the Great Lakes. The operation is unique in that both metallurgical Dolomite and Limestone are produced on site. In 1930, Port Inland was at the fore front of technological advancement. It was the first major mining operation to use roller bearings and other equipment innovations. Over the 60 years of operation, Inland Steel placed emphasis on steel making technology and iron ore mining at the detriment of the limestone operation. By the early 80's, Port Inland was no longer a leading competitor. Inland Steel, unable or unwilling to spend the capital to modernize, closed the facility in the fall of 1989.

Jan 1, 1994

By Y. Guo, C. Cao

"China is rich in tungsten resource, but they are mainly associated minerals. The similar flotability of scheelite, fluorite, and calcite resulted in the difficult separation by flotation. This work summarized the current situation and the development of flotation reagents, technological process, and mineral processing equipments in China. Fatty acid served as the collector and water glass was the depressant to expand the flotability differences in traditional flotation technology. However the water glass inevitably influenced the flotation of tungsten minerals to a large extend, and the suppressed fluorite was difficult to recover by flotation. Abundant water glass lead to the bad settleability of the tailings and the tail water was difficult to circulate, resulted in serious environmental problems. Recent study proved that the selectivity of benzene armour hydroxyl oxime acid (BAHA) salts was adequate for the separation of tungsten minerals from fluorite, calcite and most silicate minerals without any depressant. By this way, sodium silicate was canceled completely in tungsten flotation, greatly improving the recovery of tungsten and the environmental problems caused by tail water treatment would be solved fundamentally. TUNGSTEN RESOURCES AND DISTRIBUTION IN CHINA China is rich in tungsten resources and the proved reserves accounted for 60% of the world's reserves [1]. However the wolframite has been dried up and the scheelite resources had become the main resource of the tungsten metal. Table 1 showed the most large and superlarge scheelite deposits in China. China has more than 40 large and superlarge scheelite deposits and the total metallic deserves is more than 3 million ton [2]. But most of the deposits were low-grade and the associated relationship was complicated. For example, scheelite was usually associated with wolframite, molybonite, bismuthinite, pyrite, fluorite, and calcite in Shizhuyuan and Yaogangxian mine."

Jan 1, 2016

By T. C. Eisele

Previous work by the authors has shown that the performance of a flotation column can be improved by the use of horizontal baffles. These baffles prevent axial mixing and also reduce "churning" of the froth by breaking up or preventing the formation of large air bubbles. In this paper, results from tracer experiments are presented that show the effects of horizontal baffles on the reproducibility and stability of the column operation. The baffles prevent random disturbances, such as unusually large air bubbles and turbulence, from rapidly propagating along the height of the column. Because these factors are responsible for much of the variations in column performance between tests, the result is that the horizontal baffles make the column performance more reproducible, with fewer short-term variations.

Jan 1, 1999

By R. J. Sweigard, M. Rohatgi

Differential settlement on reclaimed land presents a particular problem when the land is to be used for row crops. The poorly drained depressions caused by differential settlement restrict crop yield, resulting in additional costs to alleviate the problem. Potentially more serious is the threat of failing to meet target yields due to settlement-related reductions. Because the mechanism by which the problem occurs is not well understood, a physical model study was conducted to investigate the importance of several factors. The importance was considered of such factors as the relative amounts of rock and unconsolidated overburden in the undisturbed condition and the size distribution of rock fragments. But the analysis concentrated on the causes of settlement in the reconstructed soil layer above the rock spoil.

Jan 1, 1991

By T. van Sandwijk, G. Van Weert, E. Molleman

This paper reports on test work that explored the dissolution/precipitation reaction: ZnS + 2HCl - ZnC12 + H2S, which is part of a process used in the production of pure ZnS. The research focused on the influence of proton activity on the dissolution of zinc concentrates obtained from the Brunswick Mine No. 12 in Canada (Brunswick Mining & Smelting); the Red Dog deposit in Alaska (Cominco Ltd.); and the Tara deposit in Ireland (Outukumpu Zinc). A comparison between the results of the experimental dissolution as a function of pH and the dissolution predicted by thermodynamics suggest that the three concentrates contained sig¬nificant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1999

By R. Velkova, D. Bojinova

The objective of the present investigations is to establish the effect of the preliminary mechanical activation of phosphates on the degree of phosphorus extraction by bioconversion of Bulgarian and Tunisian phosphates using A. niger fungi and T: thiooxidans microorganisms. The influence of the phosphate concentrations, the type of the nutritive medium and the incubation times on the process of biological mobilization of the phosphates was studied. When the concentration of phosphates in the medium is twice as high, an equal and/or higher degree of phosphorus extraction can be achieved through the bioconversion of mechanically activated phosphates compared with non- activated phosphates under similar conditions. A maximum degree of 90+% phosphorus extraction in utilizable form was achieved at definite conditions.

Jan 1, 2002

By John K. Hollmann

The use of the direct method of determining coal methane content has grown in the last decade from a research technique into a practical coal exploration tool. However, the literature available on the subject is somewhat lacking in site-specific guidance and observations on the conduct of the method and the use of the resulting data. This study discusses some practical lessons learned in conducting a large scale direct measurement project at an operating mine, describes the initia1 interpretations and uses of data from the project, and presents observations from subsequent mine operations into the success and limitations of using direct measurement data in mine planning. The site studied is in central Pennsylvania on the Appalachian Plateau and includes coal seams in the Allegheny series.

Jan 1, 1987

By Carrie Smith

In a major milestone for geoscience, the U.S. Geological Survey (USGS) has unveiled the Cooperative National Geologic Map, the most detailed national-scale geologic map of the country to date. The project offers a fresh, layered look at the rocks and sediments that make up the United States. For geologists, engineers and mining professionals, it provides both a technical achievement and a practical tool that will help shape future exploration and landuse decisions across the country. The new map provides a regional view of geology both on and beneath the Earth’s surface. Using different colors to represent rock types and sediments, it allows users to toggle through multiple layers, revealing for the first time the surficial and quaternary deposits that lie above the bedrock. “This is the first national map to include multiple layers of mapped geology, the first built to be easily updated as new maps are published, and the first to be delivered in a user-friendly online interface,” said Joseph Colgan, a USGS research geologist who led the development team. The Cooperative National Geologic Map is a culmination of more than a century of collaborative mapping between the USGS and the nation’s state geological surveys. More than 100 existing maps produced by state geological surveys and the USGS over the past 40 to 50 years were combined and standardized to create the national data set. During its three-year creation, the USGS prepared digital data, built the system to bring the maps together, developed the web interface and underwent a review and approval process. Through this process, decades of fieldwork, analysis and digital cartography were brought together to provide both national and local expertise.

Nov 1, 2025

By Jamal Rostami, Ataollah Rahbar

"Uma Oya Multipurpose Development Project is under construction in Sri Lanka. This project involves 2 Rolled Concrete Core (RCC) Dams connected through a tunnel currently under construction by Drill and Blast method. The water is transferred from first diversion dam to the 2nd regulatory dam and from which, it will be transferred through a 14 km headrace tunnel to the top of a 650 m deep drop shaft that feeds the high pressure water to an underground powerhouse and turbine chamber for generation of 120 MW of electricity. The Headrace and Tailrace tunnels are being excavated by two 4.4 m diameter double shield TBMs. The headrace tunnel has already passed 5km milestone and is mined in hard rock, while the tailrace tunnel has been completed in rather weak and fractured ground. This paper will review the history of the project along with the geology of the site. The operation of TBM in headrace tunnel will be discussed in more detail, focusing on the challenges of excavating through very strong and abrasive quartzite and gneiss on this site, as well as reaches of tunnel in high inflow of water reaching 400 L/Sec. INTRODUCTION This paper aims to introduce the Uma Oya Multipurpose Development Project (UOMDP) as a hydro mechanical project in Sri Lanka, targeted generating hydro-electric power, transferring water for irrigation purposes and controlling seasonal devastating flood. This project lies in the south-eastern part of the central highland region of Sri Lanka (Figure 1). The main part of the project is located in the south-western part of the Badulla district in the province of Uva. The south-eastern end of the project site is in the central west of the Moneragala district (province of Uva). Bandarawela is the largest urban setting within the project area, located halfway between the upstream and the downstream ends of the planned hydropower plant and combination of dams, tunnels, and downstream facilities. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya. The feeder (power) tunnel Lot consists of a headrace tunnel (L=15554m), the surge shaft (L=200m) and tank on the upstream of the vertical shaft, a vertical shaft with steel lining (L=650m), an underground powerhouse and a tailrace tunnel (L=3650m)."

Jan 1, 2016

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By Gösta W. Diehl

During the past five years the use of all-hydraulic drilling equipment has increased rapidly, and we have now reached a point where the hydraulic drill has become an alternative to be seriously considered for every drilling operation. The hydraulic drills have many advantages over pneumatic drills, but they also have certain characteristics, which makes a potential user hesitate before making the switch. And when the decision to use hydraulic drills has been made, the user then faces another choice of equal difficulty: the choice between different hydraulic systems. This paper discusses some of the factors to be taken into account when considering hydraulic drilling equipment for rapid tunneling in hard to medium hard rock. THE CHOICE BETWEEN HYDRAULIC AND PNEUMATIC EQUIPMENT The choice between a hydraulic and a pneumatic drill is much more than just that: It is a choice between two different systems. The choice is usually based on the productivity, economy or ergonomy of the system. However, also other factors should be considered, such as service capabilities and training requirements. And finally the choice will be influenced by the need to acquire know-how in the new technology. Productivity If the prime consideration is to achieve the highest possible tunneling speed, then the high penetration rates of the hydraulic

Jan 1, 1979

By Bruce W. Cavender, Brian L. Granger

The leaching characteristics of non-homogeneous ores have traditionally been difficult to assess in laboratory tests. A result of the large sample size necessary to ensure representativity, this difficulty is most acute for ores containing nuggets or other irregular occurrences of precious minerals. Consequently, small-scale leaching tests are often regarded as indicative rather than conclusive. The predictive nature of leaching tests can be improved by applying the experimental design concepts of blocking and randomization. In the case of column leaching, experimental 'blocks" are constructed with the same number of columns as there are separate test conditions. These blocks are treated identically throughout the test, with differences between columns within each block being the variables of interest. To maximize the uniformity of the blocks, randomization procedures are employed in the preparation of the sample and conduct of the test. The initial ore sample is screened and individual column charges composited from randomly selected increments from each size fraction. The leaching order, daily solution analyses, and processing of leach residues are similarly randomized. The observed differences in leaching performance between the columns in each block are compared to determine the over-all outcome of the test. A statistical analysis using t distributions gives a quantitative measure of the reproducibility of the outcome.

Jan 1, 1995