Search Documents

By Jon C. Volkwein

The U. S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography at the Pittsburgh Research Center. These gas results were analyzed for explosibility. Personal exposure to carbon monoxide was also monitored. The highest methane level observed was 9.55 pct. The Inert gas levels, (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were non-explosive. The maximum personal time weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining. INTRODUCTION The auger highwall mining method is an effective method to recover coal from a reserve when removal of the overburden by surface mining equipment becomes uneconomical. In this method of mining, a horizontal auger enters the coal seam from the surface mine bench under the highwall and the coal is drilled in a series of parallel holes. Historically, coal mined from the surface is relatively shallow, and over time, methane associated with the coal has dissipated through the surface. In most circumstances, little methane has been found associated with auger mining. However, mining technology has enabled surface mining of deeper reserves of coal. Furthermore, environmental constraints have forced the highwall extraction method to be used to remove coal under wetlands, further increasing the chances of encountering methane. Recently incidents of methane explosions at a few auger mining operations have resulted in injuries and increased testing for methane at the collars of auger holes. The fuel source of the reported explosions was not necessarily limited to methane, but may also have involved coal dust. The Mine Safety and Health Administration (MSHA) met with the Bureau to discuss what technology might be available to enable the safe resumption of mining. The discussion included the difficulty of ventilating through the solid shafts of the augers, that steel bits probably created the ignition source, and that perhaps inerting the holes with low oxygen and high carbon dioxide concentrations from the machine's diesel exhaust was a potential solution. Considering the ventilation aspects of the problem, it was not clear If ventilation could be reliably established. If some degree of ventilation to the front of the mining head is achieved, it may combine with methane to bring the hole atmosphere from a rich, nonexplosive mixture to an explosive mixture. Furthermore, it may not prevent a dust explosion in such a mining configuration. Lack of access through the shafts of auger type mining machines further limits the ability to add water or air to cool bits to prevent an ignition source from developing. Either of these approaches would also be expensive. The process of mining coal In an inert atmosphere has been considered in the past, but to our knowledge, never implemented (Department of Interior, 1970). Clearly, implementation in underground mining would be more complicated. On a mine bench open to the atmosphere, however, adding inert gas to the mining head could provide a quick, feasible method to prevent explosions at auger highwall mining operations. Also the problem of how to move the inert gas to the cutting head of the machine had to be considered. Preventing explosions on auger mining machines using inert gas requires three primary considerations: first is the source of inert gas; second, placing the inert gas at the cutter head; and third, monitoring the hole atmosphere. Any gas source having an effective inert gas concentration of 34 volume pct or greater will prevent methane from Igniting (Zabetakis, 1965). Sources of inert gas considered for this application included liquid nitrogen, modified shipboard inert gas generators (for hydrocarbon shipping and transfer), jet turbine engine (Paczkowski, et. al., 1982), the auger's diesel engine and a gasoline engine. Operation cost, purchase cost and availability limited our testing to the diesel and gasoline engines. This work tested each engine, separately and combined. To ensure effectiveness, both company and enforcement personnel need to know how to monitor the condition of the inerted hole. Measurements at depth inside the hole are possible by remote sampling through rigid tubing, but this method is Impractical for routine monitoring. Continuous monitoring of the exhaust gas stream is an alternative. The U. S. Bureau of Mines evaluated an inert gas system at an auger mining operation at a surface mine near Owensboro, KY. Coal was mined from the Number 9 Coalbed in Henderson Co. KY. Tests were conducted in January and March of 1992.

Jan 1, 1993

By Aladar B. Dory

INTRODUCTION Anyone familiar with the problems of hardrock mining will agree that the majority of the serious dangers present in mining are quite visible and obvious to any person reasonably familiar with the profession. Having unsecured, unscaled back over ones head, gives one a very good chance of ending up under a caved in mass of rock. Staying too close to a blast gives one almost a certainty of being hit by a flying rock. Too little oxygen in the air will very quickly lead to loss of consciousness and death. One walks only so much over deep, unsecured openings before he falls into them. It is because of this clear visibility of the conventional health and safety hazards that mining regulations in almost all jurisdictions world-wide are a more or less comprehensive collection of "shalls" and "must nots" of good common sense. When basic rules of common sense safe working practices are at stake, there is little room for dialogue and compromise. The mine inspector is then observing, during his inspection, how well the mine follows these common sense rules. RADIATION AS A HIDDEN DANGER Radiation in mines is a risk, the impact of which does not demonstrate itself immediately. It is first of all a potential risk. Two individuals exposed to identical radiation will almost certainly be effected differently, if at all. This is certainly true of exposures and doses one might encounter in the mines today. We hear very often the phrase: "there is very little known about the effects of radiation". It is one of the most misused and misunderstood half-true statements. I would doubt that there is any other carcinogen whose effects have been studied as extensively as the health effects of radiation. Where the statement is correct is regarding the knowledge of the quantitative assessment of the risk of low level radiation exposures. The reason for this uncertainty is that the magnitude of their health effect is very close to the health effects of natural radiation, cosmic radiation and the effects of other carcinogens such as industrial pollution, hydrocarbons from cars and other chemicals we have grown accustomed to using. As far as lung cancer is concerned, the effects of wide use of tobacco probably outperforms any other single substance. All this having been said, the bottom line is still unchanged. Radiation exposure, in most cases mainly radon daughter exposure, was and still is one of the health hazards of uranium mining and as such has to be controlled to the best of our ability. Various jurisdictions have adopted different approaches to the control of radiation exposures of uranium minemill workers. The following sections of this presentation will attempt to explain the regulatory approach taken in Canada. THE CANADIAN REGULATORY PHILOSOPHY As indicated earlier, the health effects of low level radiation are quantitatively not yet defined and no proven threshold of radiation exposure exists. The Atomic Energy Control Board's (the Board's) regulatory system is based on the basic assumption that there is no absolutely safe limit of radiation exposure below which there are no health effects. Theoretically we should therefore strive to reach zero exposure. It is obvious that this objective cannot be reached in real life. The objective of the regulatory process therefore has to be to achieve radiation exposures of the workers that are as low as reasonably achievable, social and economic factors taken into account. This, of course, is the internationally acclaimed ALARA principle put forward by the International Commission on Radiological Protection (ICRP). To avoid any misunderstanding it is worth emphasizing that the ALARA principle is applied to achieve exposures below the regulatory limits which must not be exceeded in normal operation of any nuclear facility including uranium mines and mills. The present regulatory limits for radiation exposures of atomic radiation workers are based on the recommendations of the ICRP and they are almost universally accepted. They should ensure that the risk from radiation exposure is not greater than the risk associated with working in a comparatively safe industry. Basically, there could be two extreme approaches to the regulation of uranium mining and milling. One extreme approach is to develop very extensive and detailed regulations and requirements covering all aspects of radiation protection. This is a somewhat autocratic approach to the regulatory process. This approach has two very serious shortcomings. If detailed requirements are set in regulations, due to the great variations of actual conditions at various mine-mill facilities, they have to be set as a compromise between the desirable requirements and those which could be met by practically all facilities. This approach takes away from the management of the facilities the initiative to strive for improved conditions. Requirements are spelled out in clear, understandable targets and the only worry of the management is to comply with these targets. One of the basic duties of management is to manage the operations in the most effective way with the maximum health and safety of the workers in mind.

Jan 1, 1981

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents with particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and the conditioning time were investigated to determine their effect on reagent coating on the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power P, to the minimum power Pm' required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain high recovery. Reagentization was slower at lower P /P m ratios. At higher P /P m ratios, the flotation recovery was optimized and the agitation speed was found to have no significant effect on it. Optimum mixing conditions were obtained for a 74 wt% slurry at an agitation speed of 450 (47 rad/s) rpm. Under the optimum conditions of mixing, recovery was improved at low collector dosages and short conditioning times.

Jan 1, 1995

By J. O. Marsden, C. Green

In 2003, a high-temperature pressure leaching circuit to treat copper sulfide concentrates was commissioned at the copper/molybdenum operation at Bagdad, AZ. In late 2007, a medium-temperature pressure leaching circuit was commissioned at the Morenci mine in Arizona. The Morenci circuit was shut down in mid-2008, following a fire in the autoclave circuit. The onset of the global financial crisis in late 2008 resulted in significant changes to the operating profile in the Southwestern United States with respect to concentrates production, concentrates treatment, acid production and acid consumption. As a result of these changes, the Morenci concentrator was shut down, and the pressure leaching circuit remained offline. In late 2014, the increasing acid requirements in the Southwestern United States prompted a reevaluation of the Morenci concentrate leaching facilities. As a result, the pressure leaching circuit was restarted in high-temperature (200 °C) mode in May 2015 and has operated successfully for three years since recommissioning. This paper describes the current pressure leaching circuit configuration and the factors leading to the successful application of copper sulfide concentrate leaching at this location.

By Qingqing Huang, Mohammad Rezaee

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 12th MPD Student Poster Contest on March 2, 2022, during the MINEXCHANGE 2022 SME Annual Conference & Expo. The event showcased the work of 32 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to explain their research to a panel of judges during the conference. Recognizing the students’ efforts in working hard on their research topics and setting aside time to complete the necessary steps to enter the poster contest, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 22, 2022

By Steven A. Savage

Agrico Chemical Company, as we presently know it, is the result of the coming together of several different fertilizer operations. The Williams Companies, our parent organization, first entered the fertilizer business in 1971, when it acquired the fertilizer operations of the Gulf Oil Company. This gave us, among other things, the manufacturing facility at Donaldsonville, Louisiana. In 1972, The Williams Companies acquired Agrico Chemical Company from Continental Oil Company, bringing in a manufacturing facility and phosphate mines at Pierce Florida. Our Florida Mines are in the region commonly known as the Bone Valley Region of Florida. The majority of the phosphate fertilizer produced in the United States utilizes rock mined in this region. The Donaldsonville Plant was originally built in 1967-68 on the site of the old Faustina Plantation at an approximate cost of $80,000,000. (This plant is commonly referred to as our Faustina Plant.) Until such time as Agrico was acquired from Continental Oil, the Donaldsonville Facility was solely used to upgrade phosphoric acid into finished granular products.

Jan 1, 1986

By Michael R. Grubbs

In most resource recovery plants the incoming solid waste material is first shredded and then air classified into a light and a heavy fraction. The light fraction which contains mostly paper, cardboard, etc., can be used either as a fuel for power generation or in the production of new paper products. The heavy fraction which remains consists mostly of glass, ceramics, wood, ferrous metals and non-ferrous metals. The ferrous metals may be removed from the heavy fraction by conventional magnetic separators. After primary shredding, most of the glass and ceramic is fine in size and may be screened away leaving a residue of wood, cardboard, and non-ferrous metals. This residual heavy fraction is the input material for the separator described in the present paper. A new metal separator was recently reported by t. Schlömann1. The author described the theoretical relationships and presented results of tests on samples of the residual fraction of municipal solid waste. This paper describes the operation of the metal separator and develops the basic separation relationships controlling the process.

Jan 1, 1976

By Kim Lapakko

Increasing public concern over the welfare of the environment has placed demands on the mining industry to evaluate the environmental impact of mining development. This is a difficult task and involves considering the influence of a multitude of variables on complex processes over a long time period. Few studies which focus on the evaluation of the environmental impact of mining have been conducted and, therefore, there is little past experience to rely upon. This article describes some of the work done to evaluate the potential environmental impact of mining development in Minnesota. Interest in developing the major copper and nickel sulfide deposits near the wilderness areas of northeastern Minnesota aroused concern regarding the environmental impact of mining development in the region. As a result laboratory and field studies were initiated to investigate the potential for trace metal leaching and acid generation due to dissolution of Duluth gabbro. Chemical equilibrium computer modeling was conducted to aid in data interpretation. The goals of the study included the investigation of leaching mechanisms and rates of release (1, 2).

Jan 1, 1980

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN, ANMAYA NAIK, ASIF AHMAD, ADITYA PANDEY

Wet kata cooling power (WKCP) measured using a kata thermometer is a well-known heat stress index in mining industries. Although over the years several researchers have proposed different heat indices and indicated the limitations of the kata thermometer, it is still being used in many areas, especially in the South African gold mining industry, mainly because of its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for WKCP, and some of the more prevalent empirical expressions. The analysis presented based on a regression technique aims to assess the disagreement between model predictions and actual measurements. It is found that the WKCP expresses bioclimatic interaction quite well under the specific parameter of interaction that explains the harsh thermal environment and air condition, such as metabolic activity, the person’s clothing, and the velocity of the air in which the person is working. The statistical analysis shows that the WKCP exhibits significant estimates to thermal stress under lower air velocities, light clothing, and higher metabolic activity rates.

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987

By John A. Patterson

There are certain data handling techniques used by statisticans that can help one to calculate the size of an orebody and to develop some of the relationships between size, cutoff grade, average grade, mining cost, and profit. Knowing the relationships amongst these factors can help determine the most desirable operating conditions. A statistical technique that we will use is data grouping. This allows us to work with relatively few groups instead of many samples, If we were able to segregate the ore in an orebody into grade groups, add the amounts in each group, and plot the sums as a curve, we would get something like Figure 1. A smooth curve develops when the grade classes are small enough, otherwise a "stair step? histogram results. The area under the curve, being the sum of the tonnages in all of the grade classes, is proportional to the total number of tons in the orebody. If we take the data of a distribution such as Figure 1 and add the tonnages above a specific grade we have in effect a cutoff grade

Jan 1, 1958

By Mark E. Emerson

1967 will be remembered as the year the world realized it was running out of silver. In May of this year a new era in tin the history of the white metal was begun as the power of the U.S. Treasury to regulate world .silver markets was staggered by one of the most intense speculative flurries in recent times. In the past few months the price of silver has risen from $1, 29 to over $1.80 per troy ounce and with it have spiraled the prices of a host of silver-bearing consumer items. Legislation has, been enacted to conserve our coinage and meager silver stocks and today large quantities of non-existent silver are trading hands at a fast pace on the commodity exchanges throughout the world. Now that the price of silver has been set loose, forces are in motion to dull the world's appetite for silver. At the same time there is strong incentive to provide greater quantities of silver to satisfy the world's hunger' for the metal.

Jan 1, 1967

By R. Callaway

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (?CERCLA?), as amended by the Superfund Amendments and Reauthorization Act of 1986 ("SARA?) establishes a comprehensive Federal regulatory program for addressing environmental and public health risks posed by releases of hazardous substances into the environment from a wide variety of industrial and other sources. The statute is primarily administered by the United States Environmental Protection Agency ("EPA"). The applicability of CERCLA to the mining, milling, and smelting industries (hereinafter referred to as the ?mining industry?) has been upheld by the courts and recently affirmed by Congress. The purpose of this article is to briefly outline the scope of CERCLA as it applies to the mining industry, the scope of EPA's activities pertaining to the mining industry under CERCLA, the types of remedies which may be pursued by EPA, and the liability scheme of CERCLA as it applies to corporate entities, managers, and shareholders involved with the mining industry. Natural resource damage claims, State cooperative agreements, and other State-related issues will not be discussed.

Jan 1, 1988

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By Andrzej M. Wala

The determination of the air quality needs to dilute diesel exhaust gases to a safe level must be individually evaluated for particular cases. One such case is when diesel-powered vehicles are working in long dead- end headings with forcing auxiliary ventilation. The vehicles perform specific operations in a cyclic order required by the technical process. The dynamics of this process in certain conditions has a vital influence on environmental conditions in the working area and in the rest of the heading. Recent studies on diesel gas behavior in long headings have shown a zone of increased concentration of pollutants (accumulation) between the face and the mouth of the heading. To be able to control these accumulations of pollutants, use of the concept of planned air discharge by using the Coanda-type ducts is proposed. The main objective of this paper is to demonstrate an application of computer simulation of that process. It is shown that, by planning the additional air discharge, the concentration of diesel gases can meet required limits along the heading.

Jan 1, 1987

By Peter G. Mason

Pressure oxidation is now a well estab­lished process for the treatment of refracto­ry gold ores and concentrates. The process utilizes pure oxygen to oxidize mineral sulphides in an aqueous slurry at elevated temperature and pressure. Gold released from the sulphides becomes amenable to subsequent cyanidation. A major component of the operating cost of this process the supply of oxygen. The quantity required is dependent on the sul­phide grade, the extent of oxidation and the percentage utilization of the oxygen. As the sulphide grade is fixed and complete oxida­tion is generally required to maximize gold liberation, the only opportunity for saving in oxygen consumption is to improve its utilization. Under circumstances where the feed material contains substantial carbonate, oxygen utilization can be improved by strip­ping carbon dioxide from the autoclave vent and recycling the associated oxygen. Fluor Daniel Wright included an oxygen recycle circuit in the Getchell pressure oxidation plant, which is operated by First­Miss Gold in Nevada. FirstMiss Gold has applied for patent rights to the process as implemented at Getchell.

Jan 1, 1990

By R. Bouzaiene

In the paper presented by F.W. Brackebusch on the “Basics of paste backfill systems,” paste fill was presented as a backfill process that offers many advantages over other alternatives such as hydraulic fill and rockfill. It was observed, however, that the mechanics of paste-fill transportation in pipelines is not fully understood and that the success of its implementation in practice depends on the precise control of the proportions of fines, aggregates and water in the mixture. The author emphasized the necessity for laboratory and full-scale testing to determine the suitability of a material to be used as paste fill. Although experimental testing is definitely an important operation in the design of a reliable paste fill, advances in the understanding of the fundamental laws that govern paste flow in pipelines are equally relevant. Ideally, the results of such efforts would provide predictive models for the rheology of the paste and the corresponding pumping-energy requirements. In an attempt to achieve this objective, an ongoing research program has been active at McGill University’s Department of Mining and Metallurgical Engineering.

Jan 1, 1995

One of the most challenging and ambitious dump rehabilitation projects in South Africa’s mining industry is being carried out at Greenside Colliery’s smoldering coal dump, which lies adjacent to the N 12 Johannesburg-Witbank highway. Greenside Colliery is the largest coal mine in the Gold Fields Group. It began operation in 1946, the year in which the burning dump had its origins. Today, Gold Fields plans to spend R16 million (about $USS8 million) to encapsulate the dump, bringing it into compliance with South Africa’s Mining Environmental Management Programme, according to Martin Hamer, engineering manager of the Greenside Colliery. The improved environmental management approach will result in reduced sulfur dioxide gas, smoke and dust emisson into the air and an enhanced aesthetic appearance of the dump from the N 12 highway. The objectives of the project are to place and compact coal discard to within the National Institute of Coal Research specifications in order to prevent spontaneous combustion, and to preserve as an asset the coal portion of the discard.

Jan 1, 1994

By C. R. Bennett

A copper heap leach model, employing leading edge computational fluid dynamics (CFD) technology, is applied to the Zaldivar heap leach operation in Chile in order to explore and analyze the possible impact of operational changes. The effect of changes to the heap operation on copper recovery has been previously investigated and reported by the Zaldivar operation. This paper examines the extent to which a comprehensive heap leach model supports the analysis and conclusions of the published work. The heap is a complex multi-phase process, consisting of a solid static porous media with complex fluid flow, gas and liquid phases, competing solid-liquid reactions, dissolution of minerals and transport through the heap. The model accounts for the physical and chemical features of the heap, including transport and reactions kinetics for the important copper and iron sulfide minerals, ferrous oxidation, bacterial effects, thermal energy, acid and sulfate balances. The model was calibrated to published data on the ore body and employed to analyze the impact of a number of operational changes, including solution flow rate, acidity, lift height, crush size and head grade.

Jan 1, 2012