Search Documents

By W. C. Yates

Lack of visibility from large, open-pit haulage truck cabs has become a serious safety problem. Anaconda conducted a research program to develop a low cost system to alert haulage truck operators to small vehicles present in blind areas. Several systems were developed and tested. As open-pit haulage truck size has increased, so has the size of the blind areas. Mine utility vehicles, pickup trucks, and cars are concealed within these blind areas and become safety hazards. Figure 1 shows the typical blind areas of a 136 t (150-ton) haulage truck. The areas of greatest concern are at the rear center and front right corner of the truck. In these "no visibility" areas many small vehicles have been crushed by large haulage trucks at various mine sites. In most instances, the occupants escaped the vehicle before it was destroyed. But injuries and death have occurred. In most cases, the accidents were attributed to negligence or carelessness by the small vehicle driver. The limited visibility problem still exists, though, and a solution is needed. Initial Solution The usual plane mirror on the driver's side and the convex mirror on the right front of the haulage truck allow only limited rear visibility. The typical, right side convex mirror is generally small and difficult to locate at a glance. This convex mirror also presents an image that distorts distance perception. These mirrors are of¬ten broken and immediate replacement not demanded or made. The US Bureau of Mines, in a contract with M.B. Associates, San Ramon, CA, developed an improved visibility system. It consisted of a larger, left view mirror and unique, blind area viewer. The large 230 x 690 mm (9 x 27 in.) left mirror has a small convex spot mirror near the bottom. The entire unit can be quickly replaced if broken. The large size provides a full view of driver orientation features such as the rear tire and the top of the load bed. The right 300 x 410 mm (12 x 16 in.) mirror has a convex surface and is quite rugged. The 510 mm (20 in.) spherical radius presents the operator with some distance distortion, but objects in its view are easily seen. The "blind area viewer" consists of a modified fresnel lens that allows the driver to "look around the corner." Installation of three of these lenses on the front of each haulage truck is rec¬ommended for adequate blind area coverage. This system significantly increases an operator's field of view and allows viewing of objects within about 3 m (9.8 ft of the truck. Many open-pit mines are nor mounting on smaller vehicles a long whip with a flag and lamp or both. This increases vehicle visibility to haulage truck operators. The whip is permanently attached to the mine vehicle. It can also be magnetically attached to transient vehicles. The whip system. though, is inadequate for visibility in the critical rear and right front blind areas. Alternate Solutions All of these visibility aids as¬sume an attentive driver. In addi¬tion, areas such as the rear blinc, area are not covered. Based on the inadequacy of existing visibility systems, Anaconda made a com mitment to further the truck de¬tection technology. The best ap¬proach was considered to be ar active system. It would notify the haulage truck operator that an en¬croaching vehicle is present. Sev¬eral systems were considered, in¬cluding ultrasonics and elec¬tromagnetics. For the ultrasonic system, com mercial and in-house design were looked at. Designing an( building transducers with the spe cific beam shape to match the haulage truck blind spots re¬quired a major technological breakthrough. False alarms ap¬peared difficult to prevent en¬tirely. They were caused by pass¬ing, trailing, or leading vehicles a., well as nonthreatening objects. As a result of these problems, the ul¬trasonic technique was not pur sued. An alternative, an electro

Jan 7, 1982

International Minerals & Chemical Corp.'s New Wales operation near Mulberry, FL, is reportedly the world's largest concentrated phosphate chemical fertilizer and phosphate-based animal feed ingredients complex. Its latest expansion represents a $191-million investment. Two Northwest draglines were put to work at the operation early last year and, according to a company spokesman, total production from the units have more than doubled that from older rigs. This article describes how the draglines are used and provides details on the New Wales operation. The principle product at New Wales is phosphoric acid, produced by reacting ground phosphate rock with sulfuric acid in large concrete attack tanks. For each ton of phosphoric acid produced, New Wales must dispose of about 4.5 t (5 st) of waste gypsum. New Wales stores the gypsum on-site, and uses durable Northwest draglines to help handle the material. Two Units Maintain the Gypsum Stack After the gypsum is separated from the phosphoric acid through 23-m-diam (75-ft-diam) vacuum filters, it is mixed with water from a 121-hm2 (300-acre) recirculating cooling pond and, in slurry form, is pumped to the top of a 121-hm2 (300-acre) gypsum stack located adjacent to the cooling pond. The slurry contains mostly gypsum (CaSO4), with small traces of silica and other elements. The water at this point is corrosive, containing from 1-2% phosphoric acid. Its pH usually ranges from 1.5-2.0. Water drains from the gypsum stack into the cooling pond. Only about 15% of the pond's water, however, comes from the gypsum stack; the balance is from various sources throughout the complex and is held in the pond to cool before being returned for reuse in the plant. About 97% of New Wales' water needs come from this recycling program. The gypsum remains on the stack, inert, ready for future processing if it becomes economically feasible. Throughout the handling process, Northwest draglines work around the stacks' rim, continually directing the waste flow and digging out dried solids to heighten the perimeter dike to provide more storage volume. When wet, gypsum is extremely soft. When dry, it compacts well and provides footing with enough bearing capacity to support the machines. Processing at New Wales started in 1975 and the gypsum storage area has already been built up 12 m (40 ft) above grade. A total of 14.8 km3 (12,000 acre-ft) of solids are now stored. The draglines dredge material from near the perimeter dikes and place it to build parallel berms. This

Jan 8, 1982

By Milton F. Searl

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technlogy are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 1, 1980

By Searl. Milton F.

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technology are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 9, 1980

By R. Allan Wallis

In the past mining engineers have tended to rely heavily on the advice of fan manufacturers in relation to fan equipment issues. A more adequate approach was advocated in a paper [ Wallis, 1965 ] submitted to the Eighth Commonwealth Mining and Metallurgical Congress held at Surfers Paradise, Australia during 1965. At that time Mount Isa Mine were in the process of installing 3 large 6096mm (20ft) diameter vertical axial flow surface fans of an advanced type [ Mathews et al, 1967 ]. The preliminary feasibility studies prior to preparing the detailed job specification for this project were extremely thorough with the result that it was possible to include detailed information and instructions in the document, ensuring the procurement of equipment that was satisfactory in all respects. Full advantage was taken of expert services provided by external organizations during the large coordinated multi-disciplinary exercise. My continuing activity and development in relation to the technology of axial flow fans is now at a stage where all known design and performance data are accessible through CAD programs [ Wallis and Kipp, 1987 ]. The extensive calculations that were necessary in 1983 can now be carried out in a mere fraction of the time, and with complete confidence. Model testing in order to validate the fan and duct design proposals is, in my view, no longer essential. The first of the computer programs enables a mine ventilation engineer to study a large number of alternative axial fan arrangements for comparison with the centrifugal alternative. By entering the volume flow rate, fan pressure and air density, he can then with ease, and rapidly, investigate the effect of various blading arrangements, downstream evasee area ratios, and hub ratios, on fan diameter and speed, with their related attainable fan efficiencies. This procedure had its origin back in the 60s when I was advising mining companies on new fan equipment. At that time such an investigation was quite lengthy and lacked the precision and completeness that is now available within the present programs. To obtain the major benefit from these outputs, it is most important not to be disconcerted by the three very important nondimensional parameters, namely, the tip flow coefficient (LAMt), the fan pressure coefficient (Kt or Kit), and the swirl coefficient (Es and/or Ep) as these are important when assessing the various design proposals. When seeking an understanding of the role and importance of each of these variables, ample help is provided in the user manual; the design recommendations are summarized in the help screens which are readily accessible within the design programs.

Jan 1, 1989

By Michael J. Martinson

Mine ventilation has been evolving as a separate field of study since the middle of the nineteenth century, and some practitioners might assert that mine ventilation has come of age as a discrete field in the last decade or two. Certainly the extensive literature now available on many facets of the subject, international congresses, the phenomenal upsurge of interest in mine ventilation in the United States of America since the passage of the 1969 Federal Coal Mine Health and Safety Act, and the existence of a virile mine ventilation society in South Africa with its own monthly journal all point in this general direction; on the other hand the lack of a rational design philosophy for ventilating mines suggests that mine ventilation may still be on the threshold of maturity. To generalise, many mines are still ventilated simply to comply with arbitrary statutory regulations, or with some ill- defined notion of reducing the risk of injury associated with the atmospheric environment in mines. Hazards in this category include oxygen deficiency, toxic gases and particulates, pathogenic gases and aerosols, explosive gases and dusts, and extreme climatic conditions. Although many mines are ventilated to abate the risk of a specific injury, there is inevitably a spectrum of latent and patent atmospheric hazards in every underground mine. The writer (Martinson, 1976) has previously drawn attention to the dearth of material on mine ventilation design in textbooks and technical journals, and to the overly simplistic approach sometimes adopted in the limited work published on the subject. The available material undoubtedly contains useful technical data and persuasive views, but seemingly could not be used to demonstrate the rational engineering approach to mine ventilation design advocated in the present paper. The range of papers presented at the 1975 and 1979 Congresses, and the diverse interests and affiliations of delegates, emphasize the multidisciplinary nature of mine ventilation. Easily recognisable topics include: Fluid mechanics Thermodynamics Heat transfer Flames and combustion Aerosol physics Radiation physics Geophysics and geomechanics Occupational diseases Epidemiology Industrial physiology Despite these heterogeneous connections there can be little doubt that mine ventilation is fundamentally an engineering field and not an off-shoot of some other branch of applied science. The distinction is important because mine ventilation has essentially developed as a form of ad hoc trouble- shooting, and in the process mining engineers have relied extensively on the assistance of experts drawn from other fields. Thus historically there has been limited scope for the application of rational design techniques, and personnel enlisted from scientific disciplines may not have had any previous experience in the intricacies of engineering design.

Jan 1, 1980

By Steve Rule, Jose Roberto Vago, Walter de Moura

Cerro Vangaurdia Gold Mine is a joint venture between AngloGold (the operator), Perez Companc and Formicruz and is situated in the southern province of Santa Cruz, in Argentina, approximately 2,150 km south of the capital, Buenos Aires. The mine is located in a severe, semi-arid environment with very cold winters and little annual rainfall (200mm). It is an open-pit operation, mining several narrow, shallow epithermal quartz veins with . gold and silver mineralisation. Commissioning of the plant commenced in September 1998 and the first dore bar was poured towards the end of the same month. The nominal capacity of the plant is 55,000 tonnes per month, with a design capacity of 60,000 tonnes per month. Prior to finalising the design, an extensive testwork programme was undertaken at Nova Lima, in Brazil, in which all parts of the process were evaluated together on a pilot-plant scale. The process flowsheet selected at Ce1rn Vanguardia is quite novel, in that it includes milling in cyanide, as well as a cyanide recovery and recycling plant on the tailings section of the treatment plant is included. The cyanide recovery process selected was a version of the acidification - volatilization - reabsorption (AVR) process, known as Cyanisorb™. The selection of the Cyanisorb™ process in the plant design was as a direct consequence of two factors:

Jan 1, 2000

By Kathleen A. Altman

INTRODUCTION The basic premise of the ideas presented in this paper are as follows: Engineers believe that "theoretically" it will work. Operators ask what they must do to make it work. And, people can screw it up. r Today the challenges conf onted during the engineering, startup and operation of mines are becoming more complex. As mining and processing professionals, we are called upon to trav­el all over the world, are subjected to a wide variety of climates and must deal with a numerous cultures and people. Historically, for the majority of the people working in the mining industry, the primary challenges related to projects have focused on the differing perspectives of the disciplines involved. For example, geologists focus on resources and reserves, mining engineers relate to tons or tonnes, metallurgists count ounces or pounds or kilograms of product, mechanics emphasize availabil­ity, human resources personnel deal with absentee rates and turnover and accountants watch the bottom line ($$'s). As the world has become "smaller" and the mining industry has become more globalized, the puzzle is becoming increasingly difficult. Even the most experienced in the crowd of mining profes­sionals are oftentimes surprised by the types of problems that are encountered. Try as we may, we cannot anticipate the complex­ity of dealing with the human side of an operation.

Jan 1, 1998

By Takeshi Tanaka, Shinya Ono, Tsuyoshi Kato, Masaji Kato, Yuusaku Tominaga

The knowledge of the macroscopic characteristics of a ventilation network is of fundamental importance for taking counter- measures to increase air quantity in-specified branches, such as those corresponding to working faces at advancing entries or longwall panels. Because the ventilation characteristics are inherent properties of each mine, it takes a long time for an engineer to accumulate experience on how a specific regulator may affect the air quantity in a specific branch of a mine with a complicated ventilation system. A computer-simulation training system, based on the macroscopic ventilation characteristics, is presented in this paper. When a trainee selects a specific condition from five regulator option (closed, almost closed, slightly open, half open, open), the change in air quantity for a network branch is indicated by the color allocated to the ratio of the new air quantity to the old or planned air volume. After the ventilation simulation, the colors in the specified branches are defined by using the fuzzy set theory. The trainee continues practicing the selection of closed/open conditions for different regulators until each of the specified branches is displayed in good state of airflow. The ventilation net- work of the Horonai coal mine is used as an example of the training system to control air quantities in six working faces with 33 regulators.

Jan 1, 1996

By S. W. Kan, M. G. Kakarkis, J. Zelanco

Grouting has been used in underground mining for more than 20 years. Chemical grouting is often used as a remedial measure when the implemented ground-control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. The utilization of polyurethane grout is restricted by its limited range of physical and mechanical properties. To overcome some of the drawbacks of polyurethane, research is being conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as Strata Grip, provides a number of features, including variable gel times and a much-reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted The assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1999

By Jorge Gutierrez C.

CODELCO-CHILE, the world's largest copper producer, began an integrated study of the informatics situation in the corporation at the end of 1980. As a result, a five years strategic Systems Plan was elaborated and approved by top Corporate management. Main points in this plan were: a systems architecture with information integration to the top level management; a higher degree of information technology in the production areas, an optional systems development resources utilization and a high profitability of the plan itself. During the study phase a series of theoretical definitions were fixed and used as a basis for the plan's design. A "common systems" approach was chosen as the development strategy instead of corporate systems or separate divisional efforts. Top management should be highly involved in the revisions of the plan, as well as qualified users should be chosen as project managers. The systems architecture should grant the information integration to the corporate level, in order to support an integrated planning and administration environment for the corporation. A total of 15 projects were defined, involving 570,000 man-hours and shifting the development efforts towards the production and production services areas. The paper presents a critical evaluation of the whole process, showing its good and bad aspects and a positive global balance. It also points some suggestions and hints to any corporation who wishes to get involved in a similar experience.

Jan 1, 1989

By A. English, Edward Martinez, L. A. Haas, N. W. Johnson, Harrison Copper, M. E. Tawil, C. C. Harris, G. V. Jergensen, D. Halbe, M. P. Amsden

Declining US ore grades along with skyrocketing energy, materials, labor, and regulatory costs underscored the urgency for technological innovation in the mineral processing area. Re¬liance on the scale-up and automation of unit operations was the sector's primary battle plan. Debate continues on the upper size limit of concentrating plants and whether process controls should be centralized or distributed in the mill. In the materials handling area, the economics of large-scale and mobile systems, particularly conveyors, were well documented in the literature. Comminution, the most costly and energy consuming area of the processing flowsheet, saw improvements in process controls and liner designs. The trend toward larger grinding units stalled somewhat during the year owing to some operational problems at commercial plants. Research and development of apparently less expensive physical separation processes-that also boast recovery of cleaner and more environmentally acceptable products -gained momentum during the year. Because of escalating capital cost requirements for new plant capacity, the year saw a greater interest by mill designers to re-examine existing capacity. The focus here is clearly to modify or retrofit unit operations with more efficient components as an alternative to installing more costly new equipment. The problems facing the processing sector during the 1970s can be expected to continue in the decade ahead. Technological gains from scale-up and process controls appear

Jan 5, 1980

The concept of optical basicity is now being widely applied to rationalize and predict the chemical properties of slags. It employs signals from a probe ion to indicate the "state" or relative "freeness" of the oxygen ions in the slag, and hence provides a fundamental measure of slag basicity. Values of the bulk optical basicity of a slag can either be measured spectroscopically in samples of transparent solid glassy slag, or calculated very simply and accurately from the chemical composition of the slag. The way in which these values vary in different systems are illustrated as isoptical basicity lines on ternary diagrams, and the patterns obtained are discussed. The difficulties associated with assigning optical basicities to the oxides of transition elements are also reviewed briefly. It has been demonstrated that these bulk values can be used as the basis of a flux control model for steelmaking to achieve end-point chemistries much more reliably. Furthermore, several correlations have been established which allow the prediction of the slag-metal distribution of various solute elements. This approach has been used to predict the phosphorus distribution at the end of steelmaking, and also to custom design fluxes for the ladle and tundish to aid in the control of residual elements in the steel such as suphur, hydrogen and nitrogen.

Jan 1, 1990

By F. -J. Wodopia

Sustainability of energy supplies has been an issue of general interest for a long time. Whilst in the past the continuous productive use of natural commodities was in the fore, its compatibility with the environment and climate and ultimately also social aspects have recently gained more and more attention. Today many discussions focus on the climate compatibility of individual options to act. Fossil fuels, in particular coal and lignite, are generally challenged because coal use makes a significant contribution to global man-made CO2 emissions. The drastic increase in the consumption of fossil fuels is not explained by the fact that coal utilisation technologies are not or cannot be sustainable but rather by the growing world population and the endeavours numerous national economies trying to catch up economically. Coal is the world’s No. 1 fuel and, in the view of many experts, will keep this position also in the foreseeable future. The access to its deposits plays a significant role for the economies of the emerging countries. Consequently the aspects of energy security and economic efficiency need to be considered at eye level with climate compatibility. In Germany, however, the public acceptance of fossil fuels and of large industrial projects is in the focus of attention.

Jan 1, 2011

By Jr. Schnakenberg

The automation (robotization) of coal mining activities at the face offers improvements in worker safety and productivity. The evolutionary introduction of autonomous, intelligent robotic machines to perform the most hazardous tasks may become a reality within the next 10 years. The U.S. Bureau of Mines Robotics and Automation research program is aggressively pursuing the development of the enabling technology necessary to achieve this goal. This program consists of both core and applications research, each focused on the fundamental issues of robotic technology. In the short term, the research is directed specifically to the robotization of present-day underground equipment and is being performed in a manner that can make incremental improvements in safety and productivity. The long-term goal is the development of intelligent autonomous mining systems.

Jan 1, 1990

By C. E. Jordan

The Bureau of Mines has investigated the fundamentals of fatty acid/fuel oil conditioning for improved flotation selectivity. Both conditioning time and intensity can provide optimum flotation selectivity as well as good recovery. Traditional conditioning seeks to optimize conditioning parameters with subsequent recovery of the hydrophobic mineral. In the fatty acid/fuel oil system many silica gangue particles are also rendered hydrophobic by the flotation collector. Fundamental studies have shown that particle-particle collisions transfer the collector reagents selectively to the mineral surfaces with the highest affinity for the reagent. This mechanism deactivates the gangue particles while increasing the collector reagent loading on the selected mineral. The degree of this transformation is directly related to the number of particle-particle collisions which can be controlled through conditioning time or conditioning mixing intensity.

Jan 1, 1995

By G. B. Walker

The success of Heavy Media Separation, the static sink-float process, is evidenced by the operation of an estimated 300 installations treating many millions of tons per year of a wide variety of mineral products ranging in value from gravel to diamonds. The static heavy media process is usually limited to the treatment of plus 1/4 inch material. Mr. Victor Rakowsky, who was largely instrumental in the development and application of heavy media separation, recognized the need for a new apparatus and process which would extend the application of heavy media into the finer size range without placing a restrictive limit on the top size of the feed. He recognized the requirement for the application of centrifugal force to augment the force of gravity in separating fines by sink-float techniques.

Jan 1, 1966

By T. P. Meloy

Like our wives, the comminution of brittle solids is easy to recognize but difficult to describe. However, describing it we must. Describing the fracture mechanism of brittle solids permits the eventual mathematical quantification of the results, process optimization and control strategies. This paper presents a physical model of brittle solid comminution that explains why the slope of the log-log size distribution curves have a slope of one or less in the smaller particle sizes. To develop the hypothesis, modifications of the Gaudin Meloy physical model are made. In brittle solids, comminution takes place by cracks propagating through the material. These cracks may bifurcate as they move. Cracks may terminate either on the original surface of the material, or on a secondary crack within the material formed earlier in the comminution process.

Jan 1, 1994

By S. C. O?Brien

This paper develops the procedure for simulating the special locked-cycle Work Index laboratory test using the kinetic parameters obtained by conducting standard size-mass balance (SMB) grinding tests and presents the results for three materials - quartz, a taconite iron ore and a bituminous coal. It was found that the WI could be determined by simulation; however, if a material breaks abnormally, a full description of its abnormal breakage is necessary. It was also found that the sensitivity of the WI test procedure to the sieving process and the estimating of the 80% passing size of the sieve undersize is sufficient to question the practice of quoting a WI to two or more decimal places. Finally, if a material grinds abnormally in the Work Index mill, then the WI test should not be conducted.

Jan 1, 1987

By J. Kallioinen

Theoretical considerations, experimental results and plant experience have lead to a new design concept called the unit reactor approach. It has been successfully implemented to the largest flotation cell on the market, the 4000 cu ft OK TankCell. The work has also lead to a new operating idea called size specific flotation. The paper discusses these concepts in the view of full scale field experiments. In large scale porphyry copper flotation experiments conducted in Chile the new large TankCell with its new low energy input Free Flow mechanism out-performed the more conventional designs. The recovery was substantially better, especially in the coarse fractions. In some experiments the difference in total recovery was up to 10%-units and the savings in total energy consumption at the same time over 40%.

Jan 1, 1995