Search Documents

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By W. R. Reed, Y. Zheng

A recent study conducted by the National Institute for Occupational Safety and Health (NIOSH) evaluated the roof bolter canopy air curtain (CAC) systemin a blowing face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. This study evaluates the roof bolter machine CAC while operating in an exhausting face ventilation system. This study considers two similar locations to allow comparison with the previous blowing face ventilation (Zheng et al., Min Metal Explor 36(6):1115–1126, (2019)) study: (1) a roof bolter machine bolting the roof at 20 ft (6.1 m) from the face and (2) a roof bolting machine bolting at 4 ft (1.2 m) from the face. The environment introduces 6.0 mg/m3 of respirable dust to represent the roof boltingmachine operating downstreamof the continuous miner. However, the exhausting face ventilation uses an exhaust curtain with 9000 cfm (4.25 m3/s) of air. Two roof bolter machine working positions are simulated with the use of dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8%. When the roof bolter machine operated close to the face, increasing CAC airflow was required for adequate protection since the dust reductions can be as low as 39.5%. Additional CAC airflows of 350 cfm(0.17 m3/s) and 450 cfm(0.21 m3/s) were evaluated and demonstrated that dust reductions increased to 59.7% (350 cfm) and 72.0% (450 cfm) for the worst location where the roof bolter operators located.

Aug 26, 2020

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By B. T. Lusk, J. M. Hoffman, J. Silva Castro

Blast vibration induces sounds within neighboring residences. A housewide vibration and sound monitoring system was installed in a West Virginia home subjected to blasts from various distances and directions. Eighty-nine blast events were monitored and analyzed. Fifteen channels of data were collected, including data from three triaxial geophones, one airblast microphone, one uniaxial geophone mounted on the wall of the house (response channel) and four microphones that recorded CD-quality sound waves inside the house. Each of these channels was recorded on the same time scale. The response channel signal was easily separated into ground vibration and airblast-induced movement, due to differences in the time of arrival. This response channel was then compared to the sounds recorded to determine which component of blast vibration induced the maximum sound response. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast, while for blasts beyond 762 meters (2,500 feet), the maximum sound response was caused by ground vibration without exception. When airblast was identified as the dominant sound generator, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator, the peak amplitude of sound was not related to the amplitude of ground vibration. Findings from frequency analysis showed that the frequency content of sounds inside the house was not related to the frequency content of airblast or ground vibration, regardless of source. This finding suggests that residents will have difficulty determining the source of blast-induced noise in their homes. The proposed airblast response factor (ABRF) can aid blasting operations to determine the dominant source of sounds inside a complainant’s house based on the time-of-arrival relationships. With this site-specific information, public relations responses can be developed accordingly.

Jan 1, 2010

By Ernest F. Giovannitti

A couple of years ago, one of the major television networks produced a series on the environment. One episode in the series dealt with the nation's solid waste problem and some of the research being done to solve it. It was interesting to listen to one researcher who was attempting to develop a glass that when broken would dissolve in water. It was said that using this glass would eliminate over 100 million tons of solid wastes each year. At first glance, it would appear that this research-effort would make a significant contribution to environmental pollution control; however, if one pauses to consider the water, he can see that this solution to the solid waste problem may well contribute to a water pollution problem. The dissolved material must either end up in our surface streams or be removed in waste treatment systems. Either alternative may have a more adverse effect on the environment than the original problem. With today's emphasis on the environment, it is important that the effects of our activities be studied in depth. Then, by properly planning the activity, the adverse effects can be minimized. The coal mining industry 100 years ago was in the same boat, as our glass maker, is today. Unfortunately, it too failed to consider all the effects of its activities and as a result, in Pennsylvania, there are over 5000 miles of streams adversely affected by coal mine drainage. The situation is improving, however, because mine operators are beginning to recognize and accept the methods for controlling coal mine drainage. The purpose of this paper is to discuss the measures for the control of coal mine drainage and to set forth the factors that affect these controls.

Jan 1, 1972

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By John B. Gustavson

Gold was first discovered in Alabama in 1830. Before a decade had passed more than 20,000 people were employed in the various gold districts scattered across east-central Alabama. By 1849 most of the presently defined gold districts were known with such towns as Arbacoochee, Chulafinnee, Goldville, Pinetucky, and Idaho being the principal mining camps. The California gold rush of 1849 signaled the end of intensive prospecting in the Alabama Piedmont for the precious metal. Reactivation of many of the old gold districts has been attempted several times since 1849. Significant activity and development took place between 1874 and 1880, 1888 and 1916, and 1929 and 1936. Locally, some of the development met with moderate succes. The last productive gold mine in Alabama ceased production in 1935. The sharp increase in gold prices since 1973 has caused renewed interest in the potential values of gold of the Alabama gold districts. Most of the gold workings have been abandoned for nearly 75 years and are for the most part inaccessible for convential property evaluation. The early gold miners and prospectors in Alabama were more intent upon finding and mining the valuable metal than in recording their activities for future generations. No matter how interesting or historically significant these records might have been the miners kept no records and left behind them few maps as clues to their activities. Inasmuch as most of the old gold districts have been extensively mined and prospected during the past 150 years, there is very little chance of finding large deposits through conventional outcrop prospecting methods. Similarly, the present geologic knowledge of the various districts is insufficient to launch successful exploration programs looking for large blind lode deposits in new locations within the general gold bearing region.

Jan 1, 1975

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971

By Moussa Wone, William Levy, Christopher Caruso, Zachary Spera, Thomas Hennings, Richard Stacy Kinchen, PE Joel Kantola

"Owners constructing new combined sewer overflow (CSO) systems increasingly seek to have project design lives of 100 or more years in response to the growing size, complexity, and cost to construct and operate these systems. However, a codified and universally accepted approach to achieving this goal in the United States does not currently exist since service life prediction is a relatively new technical field. This paper discusses how the 100-year design life requirement was met for the design of tunnels, drop shafts, and diversion structures in the DC Clean Rivers Program (DCCRP). The authors identify some commonly referenced publications, present the testing framework used by the program manager to characterize the CSOs, review the design criteria used to guide the 100-year design life development, and establish guidelines to be considered by program managers and designers when implementing similar extended design life requirements in other CSO control programs.INTRODUCTIONLike many older cities in the United States, the sewer system in the District of Columbia consists of both combined sewers and separate sanitary sewers. When the capacity of a combined sewer is exceeded during storm events, the excess flow, which is a mixture of sewage and storm water runoff, is discharged to the District’s receiving water bodies (Anacostia River, Potomac River, and Rock Creek) and tributaries through outfall structures. This excess discharge during storm events is called a combined sewer overflow or CSO. A total of 53 CSO outfalls for the combined sewer system are listed in DC Water’s National Pollutant Discharge Elimination System (NPDES) Permit issued by the U.S. Environmental Protection Agency (EPA). The DC Clean Rivers Program (DCCRP) will reduce the number of CSO outfalls into the Potomac and Anacostia Rivers and decrease flooding in DC neighborhoods during extreme rain events by capturing, storing, and conveying diverted CSOs to the Blue Plains Advanced Wastewater Treatment Plant."

Jan 1, 2016

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By S. Castro, L. Gutierrez

A classification of flotation processes carried out in concentrated electrolyte solutions, e.g., seawater, is proposed using the most obvious features of these processes: low or high content of Mg2+ and Ca2+ ions, pulp ionic strength, and pH. The first distinguishable group is the processes carried out in NaCl/KCl solutions, about 0.5 M in the case of salt flotation of inherently hydrophobic minerals, and at concentrations about 10 times higher in the flotation of potash ores. In the flotation of sulfide ores, such as nickel or copper ores, with xanthate-like collectors, the xanthate collector is apparently not affected by pulp ionic strength and only adjustment of frother may be required. Content of Mg2+ and Ca2+ ions in seawater is the main difference between such systems and fresh water. The presence of these metallic ions can adversely affect flotation in the pH ranges over which these ions hydrolyse. The successful flotation of Cu-Mo ores typically requires depression of pyrite at high pH values achieved with the use of lime. However, in seawater, flotation of Cu-Mo ores requires removal of the hydrolysis products of the Mg2+ and Ca2+ ions or the use of a pyrite depressant that can be effective over the pH ranges that are much below the pH of hydrolysis. Mg2+ and Ca2+ ions also affect flotation of phosphate ores with fatty acids. In this case, the depression mechanism is not caused by precipitating magnesium hydroxides on the mineral surface but by precipitation of collector insoluble salts, and the same ions are responsible for depression in both cases. In the seawater flotation of Cu-Mo sulfide ores and phosphate ores, the practical solution involves either removal of Mg2+ and Ca2+ ions prior to the flotation or complexation with other reagents.

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

By W. M. Cross

The use of fillers and reinforcements for plastics has increased considerably over the past few decades. For example, in the 1980's the average growth rate of filler use was 5.8%. [Katz and Milewski, 1987] Similar filler use growth rates occurred in the 1970's due largely to the increase in price of petrochemical starting materials for plastics. While filler use is still sometimes predicated on the cost benefits associated with their addition to the plastic, other mechanical and performance advantages associated with filler addition are being realized, and account for most of the increased usage. Plastic filler types are many and varied, and include both inorganic minerals/metals and organic compounds, with the former type being, by far, the more common. Common mineral fillers include oxides, including both natural and synthetic silica; carbonates, particularly calcium carbonate; clays such as kaolin; and silicates like mica and talc. It has been recognized that a number of factors influence filler performance, including particle size, shape, surface area, and hardness to name a few. In addition, the interaction between the filler and the plastic is of paramount importance as this interaction will determine the wettability, bonding and the adhesion between the two materials, and ultimately, the mechanical properties of the composite. Froth flotation has long been recognized as a viable process to separate different mineral types. [Leja, 1982] Prior to flotation the minerals are liberated from the ore by comminution. The mineral particle size range produced by this comminution process is typically between 300 and 10 microns. This size range is also typical of mineral fillers for plastics. The size similarity between mineral fillers and minerals concentrated by froth flotation is only one of many similarities that can be found.

Jan 1, 1997

By Karl J. Benecke

Though the first patent on a bucket wheel excavator was granted in 1881 in the U.S. this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with the development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generating, despite the low heating value of German lignite in the order of 8500 kJ/kg (3600 BTU/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is in the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output open pit mines. The largest one, Fortuna Mine in the Cologne district, produced a, total of 45 000 000 t lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95 200 000 bank m3 equal to 200 000 000 t overburden had to be removed to accomplish this lignite output. The largest BWE (Fig. 1) ever built is working in the Fortuna Mine, too. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 t, its wheel diameter 21.6 m, as high as a 7-storey building.

Jan 1, 1977

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages —basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP increased by 3.5 percent from 2004 to 2005. The nominal GDP was $12.5 trillion at the end of 2005. Housing starts were up by more than 5 percent for the year, and the unemployment rate decreased to 5.1 percent in 2005 from 5.5 percent in 2004. The prime interest rate increased from 5.25 percent at the beginning of the year to 7.25 percent at the end of the year. The value of minerals mined in the United States in 2005 rose significantly because of increased unit prices for some metals —particularly molybdenum — and significantly increased production for some industrial minerals, mainly cement, construction sand and gravel, and crushed stone.

Jan 1, 2006

By D. E. Severson

The coal solution refining process under investigation is basically a modi¬fication of the German Pott-Broche Process, on which patents date back to 1927, (5, 6). This process was used in Germany during World War II for the partial dissolution of coal in hydrocarbon solvent and removal of the ash by filtration to produce a raw material for carbon electrodes for aluminum plants. At the end of World War II the German synthetic fuel program, of which this process was a small part, was abandoned as not economical. In recent times the whole field of coal liquifaction has been given a new impetus; present technology indi¬cates that the economic processing and refining of coal may be possible in the United States. A number of approaches to coal liquifaction have been investigated, and several of these are currently being funded by the U. S. Office of Coal Research. One approach is direct thermal treatment of the coal as in the FMC Project COED, in which coal is thermally cracked to produce gas, liquid products and char. Another approach is the Hydrocarbon Research Institute's H-coal process in which coal is catalytically hydrogenated. Two other federally funded projects involve the extraction of coal by solvents. The Consolidation Coal Company's Project Gasoline, now in the pilot plant stage in Cresap, West Virginia, is an attempt to produce gasoline plus a residual char by partial solution of the coal substance. The coal de-ashing process being developed by the Pittsburgh and Midway Coal Company is a modification of the Pott-Broche process. Coal derived solvent is used with hydrogen to dissolve the entire coal substance, subsequent filtration removes the ash and the solvent is recovered for recycling.

Jan 1, 1968

By N. Weidner, V. A. Samaranayake, K. Awuah-Offei, S. Que

"This research sought to facilitate improved stakeholder (community) analysis using discrete choice theory (DCT). The work considered 16 project attributes and four demographic factors. The discrete choice experiment was conducted in Salt Lake City, Utah to illustrate the usefulness of DCT in mining stakeholder analysis. The data was used in discrete choice modeling of individual preferences. The approach answers three important questions for enhanced stakeholder analysis: (1) What are the factors that affect individual preferences? (2) What is the effect of demographics on individual preferences? (3) What is the value of environmental and social impacts to individuals in the community? INTRODUCTION Stakeholder analysis is crucial for effective stakeholder engagement because it is important to identify and characterize stakeholders in order to effectively engage in dialogue with them. This is not only true for all stakeholders but true for characterizing the members of a particular stakeholder. The local community is usually the largest and most diverse single stakeholder group. Also, the local community is perhaps the most important stakeholder group. Thus, analysis of the local community is essential for project management. Conventional mining stakeholder analysis is a three-step process, which involves evaluating: (1) each stakeholder’s view of the project (positive, neutral, or negative); (2) how influential each stakeholder is (high, medium, or low); and (3) how they will be impacted by the project (high, medium, or low) (ICMM, 2012). The results of this evaluation are documented in a stakeholder analysis matrix (Table 1), which is used to classify the stakeholders into three groups: highly influential supporter of the project, neutral about the project, and highly influential opponent of the project. This process can be used to describe groups of stakeholders (e.g. community, non-governmental organizations, etc.) or individuals making up a particular stakeholder group (e.g. members of the local community)."

Jan 1, 2016

By I. Yildirim

Water contact angles of talc powders were determined from the values of the heats of immersion measured using a flow microcalorimeter. The results were used to calculate the contact angles using a rigorous thermodynamic relation. In the present work, the calculation was carried out using the temperature coefficient of the contact angles determined experimentally using another method. The results obtained in the present work on several different talc samples are compared with those obtained using other methods.

Jan 1, 2001