Search Documents

By Chris Laughton, Bernhard Spoerr

"Tunnel inspections are increasingly needed to ensure that aging infrastructure does not fail in service. To this end the time between inspections is being reduced, the thoroughness of each inspection is being increased to provide for a more detailed assessment of conditions and inventory defects. The conventional Tunnel Report, containing hand-drawn maps and/or photos, and a log describing observed defects and areas of deterioration, is being increasingly replaced by LiDAR generated 3-D surface maps. The data collection process that traditionally supports development of a Tunnel Report is labor-intensive, taking crew-days of engineering effort, and requires partial or full stoppage of tunnel operations. In an urban setting, such multi-day interruptions in service are difficult to countenance for a near-capacity tunnel operation. Under time pressures, the detail and accuracy of the manual inspection process will inevitably be compromised, resulting in a high cost, low quality product. As the tunnel inspection window decreases the argument for incorporating laser scanning in to the inspection process is increased dramatically... The 3D scan technology allows detailed and accurate data to be collected within the tight time frames demanded by the owners and operators of critical infrastructure. Not only does the use of laser scanners improve the 3D accuracy of the data collected, it also, enhances the efficiency and safety of the inspection process, reduces data collection and processing costs and enhances the reliability of results over time. The paper will also demonstrate the value of adding photogrammetric data to the 3D Model to show surface defect discoloration. The accurate and detailed data collected by a combination of LiDAR and photogrammetric techniques provide superior data needed to inform critical asset management decisions related to maintenance, repair and replacement."

Jan 1, 2016

By Chris Groccia, Damodara R. Chinnasane

Vale is in the process of resuming mining in the lower 810 ore body (810 OB) below 4130L at Copper Cliff Mine – South Side. Production in the lower 810 OB had continued until it was temporarily ceased in 2017 to allow for the execution of activities associated with Copper Cliff Mine Phase 1 project. While mining the stopes in both the lower and mid part of the 810 OB, a seismic response was experienced that resulted in rockbursts and challenging mining conditions. The majority of the rockbursts experienced in the past were associated with stopes mined in a bottom-up mining sequence under a diminishing pillar situation between 3350L and 3540L. The current mining plan is comprised of both top-down and bottom-up mining fronts using a center-out chevron sequence of long hole open stopes to manage induced stresses. Numerical modeling assessments have been carried out to forecast the response of the rock mass due to the planned mining. Seismicity and stress induced damage surrounding excavations are anticipated, and areas requiring extra attention have been identified. A tactical approach is being used to prepare the area for production, including replacement of ground support elements that are damaged or have insufficient residual capacity, and installation of dynamic support in areas anticipated to experience bulking and/or dynamic loading that would exceed the current support system’s capacity. A series of monitoring programs are being put in place to confirm current conditions, and to monitor the response of the rock mass to proactively implement ground control tactics should the need arise. This paper provides a summary of the approach used to forecast, monitor, and manage the behavior of the 810 OB rock mass response to continued mining at depth.

Apr 26, 2022

By George H. Roseveare

Early flotation dealt primarily with the bulk concentration of sulphide minerals or the separation of one sulphide from another and was referred to as oil flotation because oils and fats were used as reagents. The separation or concentration of one nonmetallic mineral from another developed later with the use of fatty acids. Fatty acids are organic acids present usually as glycerides in tall oil and oils of fish, peanut, cottenseed, soya beans and ethers of veg¬etable and animal origin. Some, of these oils and their derivatives were used by the Phoenicians as early as 600 B.C. in making soap, and the use of such reagents in mineral dressing is referred to as "soap flotation". The first use of oleic acid for the recovery of minerals was the early agglomeration process.' The coarse particles of ore, from 1/16 to 1/4 inch diameter, were coated with large amounts of soap or oil and after screaming from the gangue were recovered by screening, hydraulic or table classification. In 1886, a patent was issued to Mrs. Carrie Everson in which the essential feature was the constituted commingling of pulverized ore, fat or an oil, either animal, mineral, or vegetable, for the purpose of effecting .a. union of the free metal or metallic portion of the ore with such admixed material whereby the same may be changed in subsequent separation of quartz or other rock therefrom by washing or other suitable means. The patent mentions the use of red, cotton seed, caster, sperm and linseed oils, In the early use of collectors the amount of oil for froth flotation was often 2 to 6 per cent by weight of the ore rather than pounds per ton.

Jan 1, 1959

By Reed S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-order grinding studies in a laboratory ball mill according to the procedures described in the text by Austin, Klimpel and Luckie, using a slurry density of 70 weight percent. The results were scaled to five larger mills of 0.56 m diameter by 0.91 m length (2 ft. by 3 ft.), 0.82 m by 1.52 m (3 ft. by 5 ft.), 3.36 m by 7.90 m (11.5 ft. by 25 ft.), 4.41 m by 9.10 m (14.5 ft. by 30 ft.), and 5 m by 11.1 m (17 ft. by 36 ft.), assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distribustions and capacities for batch grinding in the 0.56 m and 0.82 m diameter mills and open circuit grinding in the 0.82 m diameter and larger mills using a one-large/two-small reactors in series model fitted to the residence time distribution measured in the 4.41 m diameter mill. The simulated results were compared to plant data for ranges of mill capacities. It was found that the simulated product size distributions were in good agreement with the experimental values below the 70% passing sizes, but did not agree so well in the top sizes. The predicted capacities were in approximate agreement with experimental values for the pilot-scale mills, were about 7 percent too high for the 3.36 m and 4.41 m diameter mills and about 25 percent high for the 5 m diameter mill. Use of the Bond method with the measured Work Index of the phosphate ore gave capacity predictions that were 45 to 150 percent too high.

Jan 1, 1985

By Plato Malozemoff

While this conference is dedicated to the examination of "Challenges in Mineral Processing," the broader aspect of the pursuit of this subject is Research and Development in the Mining Industry. When I was asked to speak at this symposium, I hesitated to accept. While my early schooling, training and professional occupation were in the field of this symposium, it was so long ago that I no longer feel competent to contribute anything of interest to you except perhaps for a limited historical perspective, which most of you probably already know. However, it might be worthwhile to explore the more general aspect of research and development from the viewpoint of management, as this is the stance from which I dealt with the subject for the last 30 years or so. While most managements generally have a positive view of research and development, few of the leaders in the mineral industry have actually had the personal experience of doing research for a long enough time to have obtained a full understanding and the feel for its place in the long-term technological innovation that our industry must foster. I graduated from the University of California in Berkeley with a Bachelor of Science degree and a major in metallurgy. It was during the great depression of the thirties, and it was difficult to obtain a practical job in the industry. I got a scholarship at the Montana School of Mines and received a Master of Science degree in ore dressing under Professor A. M. Gaudin, followed by another year with him pursuing research. Anyone who studied under him, or knew him well, would assert that this was a unique experience. Gaudin had a brilliant mind and a profound respect for science and the scientific method. He wished to know the scientific basis for every new technological appli-

Jan 1, 1989

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

By W. L. Price

I. INTRODUCTION Today, there are two conflicting trends facing the designer of the bulk material handling system. The first trend is the necessity to stockpile increasingly larger amounts of bulk material (coal, ore, stone etc.) as economically as possible. Fig. 1 illustrates such a typical large storage pile. The second trend is the increasing awareness of the ecological problems of today manifesting itself in a new concern over possible air pollution from storage pile surface particles. The conflict between these two trends can become dramatic when this bulk storage pile is located near a heavily populated area. Strong winds can easily create a severe local problem by blowing the particles from the pile surface toward residential and commercial areas, igniting a crisis in public relations. (2), (3), (4). To help define our combined subject and ecological culprit more accurately, Fig. 2 shows the commonly accepted size range of dust particles. A descrip¬tion of the present state-of-the-art of dust control for large storage piles is the intent of this paper. II. OPEN STORAGE PILE SYSTEMS - ALTERNATE CHOICES AND RELATIVE COSTS In discussing the open storage dust problem and possible solutions, one obvious question arises - what are the economics of placing large bulk storage under cover? Part or this answer will be found in Fig. 3 - an approximate unit capital cost comparison between several methods of storage. It will be noted that the cost curve(s) for the closed concrete silo storage illustrated in Fig. 4 is cheaper per ton at relatively small tonnage capacities, but as tonnage increases, the open pile storage unit cost (B) becomes more economical. Curve (T) covers the cost of open storage using the plow feeder arrangement shown in Fig. 5. A gravity draw-down pile with feeders at the base as shown in Fig. 6 represents yet another open storage choice.

Jan 1, 1972

By James W. Mitchell

On December 2, 1942, a scientific team lead by Nobel Prize winner Enrico Fermi first initiated and controlled a self-sustaining nuclear chain reaction. This historic event occurring beneath the stands of the University of Chicago football stadium instantly created an entirely new and tremendously broad area of technology. Indeed, the event probably changed the course of world history and considering the curret energy shortage, it probably came none too soon. Following many technological breakthroughs in the ensuing years, this event led to the first full scale nuclear fueled electric generating plant. In December, 1957, the Shippingport Nuclear Power Plant became operational and the United States had entered the era of the nuclear fueled electric generating station. Today, only fifteen years later, there are some thirty-five operating nuclear power plants in the United States with another 56 under construction and 116 on order. Still, we are only scratching the surface of this tremendous energy source. In 1970, less than one-percent of the total electric generating capacity in the United States was nuclear fueled. By 1985, it is projected that 45% of our generating capacity will result from nuclear power plants. These projections are based upoa statistics of six months to a year ago and considering the current energy shortage and recent attempts by the United States Atomic Energy Commission (USAEC) to speed the licensing process and encourage standardized plants, the contribution of nuclear power to our total generating capacity may be even greater. In summary, it is obvious that nuclear power is now, and will continue, playing an important role in our future. Those factions of government, industry and the professional community charged with fully developing this tremendous energy source must deal with it rationally, logically and expediently. The various environmental considerations in nuclear plant siting play an important role in the overall plan.

Jan 1, 1974

By Otis M. Clarke

The Eufaula bauxite-kaolin district in southeastern Alabama is an important source of raw material for the refractory industries in the United States. At the present time, five companies are mining and processing bauxite and kaolin from this district and a sixth company is holding substantial reserves. Mining operations are expanding, but finding new ore reserves is a major problem. The Geological Survey of Alabama sponsored geologic research in the Eufaula district to: 1) investigate the utilization of sandy kaolinS and other clays associated with bauxite-kaolin deposits; 2) find limits of the bauxite district, looking for possible extensions; and 3) study the geology of the district, looking for patterns or trends that may aid in finding new ore reserves. This work was done with the full cooperation of mining companies operating in the district and property owners. Research was aided by the U.S. Bureau of Mines and the University of Alabama. The investigation included detailed geologic mapping of mines, drilling in selected areas, and making mineral analyses of bauxite and clays. The mapping was performed primarily by pace and compass because of the complexity of the deposits studied, but aerial photographs were used to a limited extent. Drilling included both auger and core drilling. The auger drilling was limited to 100 feet, but core holes were drilled as deep as 200 feet. The term 'bauxite,' as used here, indicates a mixture of minerals containing more than 50 percent gibbsite. Bauxitic clay is a mixture of gibbsite and kaolinite that contains more kaolinite than gibbsite. The term "kaolin" indicates a clay composed of predominantly kaolinite. Other clays in the Eufaula district are composed of kaolinite, illite, quartz, mica, and goethite or hematite.

Jan 1, 1971

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

Caterpillar unveiled a new dozer, the new Cat D10T2 dozer, that builds on the success the company has had with its D10T model. The newest version of the dozer includes refinements to its power train, automated controls and structures. The result, the company said, is high productivity with superior fuel efficiency, reliable operation with long-lived structures, as well as enhanced access for service technicians and operators. The D10T2 uses the latest load-sensing hydraulics technology combined with Cat advanced engine controls to maximize the amount of material moved for every drop of fuel burned. Improved filtration protects the fuel system, hydraulic system and power train oil system to help ensure high reliability and minimal machine downtime. Refined large structures, such as redesigned track roller frames, deliver longer service before rebuilds. Improved access and egress features enhance safety and productivity of technicians and operators, and optional powered access systems and platforms enable configuring the D10T2 for the site. Caterpillar offers the D10T2 with two variations of the Cat C27 engine with ACERT Technology. One version is U.S. Environmental Protection Agency (EPA) Tier 4 Final certified, and the other is capable of achieving emission levels equivalent to EPA Tier 2 standards. Both engine configurations produce net power of 447 kW (600 hp) in forward gears and 538 kW (722 hp) in reverse gears. The engine controller automatically adjusts power output based on the direction of travel. With the new system, the D10T2 has about 20 percent more power in reverse compared to its predecessor model. The result is faster cycle times and greater productivity in certain applications. The D10T2 is suited for a variety of applications including mining, heavy construction and bulk materials handling.

Mar 1, 2014

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By C. Hosten

This paper presents the results from an extensive research program on the vacuum filtration of iron ore slurries. Experiments were conducted with the addition of several types of flocculants and surfactants. The filtration response of the slurries was studied in terms of the cake formation rate and the residual cake moisture. An analysis of the results is presented in ascertaining the role of flocculants and surfactants during filtration

Jan 1, 1983

By Alton G. Woody

Like so many installations of its type approaching middle age, the ore processing and shipping facilities in Puerto Ordaz, Venezuela, have taken a lot of twists and turns in their lifetime. The object of this paper is to lead you through these twists and turns and some of the reasoning for them. The need for additional sources of iron are in the United States became evident during the time of the second world war. An exploration team from U. S. Steel located further high quality direct shipping iron are in commercial quantities near Ciudad Bolivar, Venezuela in 1947. Basic decisions were made to develop these reserves for export via the Orinoco River through a new shipping port to be built at the confluence of the Orinoco and Caroni Rivers. The basic concept was for the ore to be loaded directly to ocean going vessels. This was something of a gamble since the basic economics depended upon successfully opening up the main channel of the Orinoco River to deepwater vessels, and the Bethlehem Steel mine in the same area was already working with shallow draft river boats and a transfer station on the coast. Always, the basic philosophy has tended to be to plan with expansion in mind. The original conveyor systems were 1.52 m (60 inches) wide with 200 idlers, whereas 1.07 m (42 inches) or 1.22 m (48 inches) wide conveyors could have carried any production foreseen at the time of installation. Stockpiles have been located and designed with room for expansion. Basic designs have had dotted line future expansion blocked in.

Jan 1, 1978

By William C. Cassun

The important role of pit slope design in the overall economics of open-pit mining ventures has long been recognized and well documented.1 2 Any economic analysis of a pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. The conventional practice in pit slope design is based on the factor of safety analysis.' The approach uses average values to arrive at a deterministic solution to slope stability. Past analyses based on this approach generally have had several drawbacks: 1. The risk from slope failure could not be quantified. 2. Only relatively simple pit wall geometries were considered. 3. The analyses were performed solely for the benefits of steeper slopes, seldom discussing the potential costs of slope failures. 4. Analyses were seldom considered in a year-by-year mine planning context. Recognizing that average values do not reflect the uncertainty in geomechanical parameters, a probabilistic philosophy to slope design has evolved. 4,5 However, this approach had not been fully developed to include complex slope geometries and mine planning consideration. In order to develop an integrated, pit slope design procedure, a research project was initiated at the University of Arizona during 1973 in conjunction with the Canada Center for Mineral and Energy Teleology. This research resulted in the development of a probabilistic design procedure. The remainder of this paper gives an overview of the probabilistic design procedure and a discussion of the requirements for the benefit-cost analysis of a pit slope design. Finally, the results of a case study undertaken at an operating mine are given.

Jan 1, 1977

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

Belle Fourche Shale was processed and characterized for use as a clay-based ceramic. The shale was wet sieved to produce particles that were ± 150 μm. X-ray diffraction (XRD) revealed that the -150 μm material was enriched in clay content compared to the unprocessed materials, whereas the oversize material was enriched in quartz compared to the undersize sample. Particle size analysis was performed on the—150 μm sample, which showed that the median particle size was around 10 μm. Scanning electron microscopic (SEM) analysis further confirmed the small plate size, which appeared to be primarily layered clay particles. Next, the -150 μm particles were rolled into a green body, dried at room temperature, and fired at 998°C. The fired piece was analyzed by XRD and contained 6 wt% hematite, 55% quartz, 19% microcline, and various other minor amounts of minerals. When fired at 1152 ℃, mullite was found with increasing hematite compared to the 998 ℃ firing. A multi-spectral analyzer was used to quantify the color change of the 998 ℃ fired (orange) to the 1152 ℃ fired (red) samples. Micro-computed tomography (Micro-CT) of the unfired body exhibited very few large pores, while the piece fired at 998°C also exhibited few and small pores, the overall porosity of the fired body increased. Microhardness data, obtained from the aforementioned samples, resulted in Vickers Hardness (HV1.0) values of 70.8 HV1.0 (998 ℃) and 485.7 HV1.0 (1152 ℃). Three-point bend testing was performed, giving an average strength of 23 MPa on pieces fired at 998 ℃. The average bending strength of the samples fired at 1152 ℃, was 55 MPa.

Sep 26, 2023

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

Investigation and uptake of filtered tailings continues to grow throughout the globe. This is driven by a wide range of site-specific considerations, which include such factors as tailings characteristics (e.g., amenability to filtration), production rates, climate, water availability, cost drivers, environmental requirements, and social factors. Despite the aforementioned technological growth, the currently available filtration technology is not able to meet the needs of many operations and projects that would otherwise adopt the technology. Experience with large-scale industrial filtration shows that vacuum belt filter systems meet the needs of many modern users, exceptions being the inability to effectively dewater tailings at altitude and/or with a fine particle size distribution: a potential fatal flaw. This paper presents a case study on the utilization of the patented Viper Filtration technology on gold tailings to overcome this challenge and shares the resultant full-scale plant design, highlighting the features designed to overcome cost and scalability deterrents. This technology is a novel mechanical process which complements the vacuum pressure in dewatering the filter cake as it travels along the belt filter. This project commenced with a pilot testing program, which successfully met the objective to rigorously test, measure and record any performance improvements achieved when engaging the Viper technology. Of the two tailings products tested, gross improvements of 4.2%w/w and 5.7%w/w were achieved when compared to the conventional vacuum belt filter operation. This pilot testing facilitated measurement of operating and design data, which forms the basis of the full-scale system design and resultant equipment supply of three vibration roller assemblies for retro-fitting on the existing vacuum belt filter.

Jan 25, 2021

By T. W. White

One of the objectives of today's mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

By Dick T. Atkinson

Due to improvements in the safety of other aspects of mining (primarily in roof control), haulage related accidents, particularly rail haulage accidents, are about to become the most common category of hazards causing death and injuries to underground coal miners. The major causes of these accidents are collisions between vehicles, men caught between rib and trip or between cars, derailments, and runaway cars. Such hazards can be greatly reduced if the motorman has the capability to selectively couple and uncouple cars from the cab of the locomotive, to transmit braking intelligence to the coupled cars, to determine if the trip is intact, and if brakes are automatically applied in any uncoupled car. These capabilities can be provided through an improved coupler system, designed and built by Foster-Miller Associates under a Bureau of Mines contract. Early in the program, a survey of rail haulage patents and literature was conducted. Manufacturers of couplers, mine cars and braking systems were contacted and information relevant to the remote control mine haulage application was collected. From this information evolved a working specification and a design concept. The key elements of the specification, shown in Table I, are the result of a detailed tradeoff study and considerable thought given to the specific problems encountered in the mining environment. A brief explanation of each element is as follows: Automatic Coupling - The couplers operate similarly with most already in underground use - they latch together when a trip is backed into a car intended for coupling. Remote Uncoupling - From the locomotive, the motorman can decide how many cars are to be uncoupled, operate the appropriate controls, and the desired coupler is opened.

Jan 1, 1977