Search Documents

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By Stephen P. Signer

The U.S. Bureau of Mines is developing an intelligent system for roof' control that uses both an expert system and neural networks to improve the capability of mining engineers to evaluate roof support effectiveness for ground control in coal mines. The expert system com- pares roof support capacities with the support requirements estimated to be necessary to maintain entry stability. It does this by evaluating the results of tests on various types of roof support and establishing the maximum allowable load according to anchorage capacity and yield strength of the support. After the user enters geological information (rock properties, geometry of the opening, in situ stresses, bolt pattern parameters, etc. ), the expert system compares the predicted required loading to the roof support capacity and gives the operator advice on the adequacy of the design and how improvements could be made. A good source of the real-time data necessary to allow the expert system to make decisions will come from a roof bolting machine being developed by the Bureau of Mines. Researchers have collected data from a Western coal mine on drill bit position, penetration rate thrust, torque, and rotation rate. Using this information, two neural net- works were developed to identify different types of strata and features in a mine roof such as rock type, rock compressive strength and joint characteristics. The result is a system that can assist a mining engineer with design information that can be constantly updated as mining progresses.

Jan 1, 1992

By Richard H. Gates

INTRODUCTION The U. S. Army Corps of Engineers is developing chemical explosive excavation as a construction technique for use on Civil Works projects. Large chemical charges are being used in multiple charge arrays in a variety of media and topographic situations to achieve actual construction projects. The target is the development of chemical and nuclear explosive excavation as an accepted cost-competitive construction technique. Military research using explosive excavation is also being conducted to apply this technique to military engineering for combat purposes and to military construction. The information gained from both the civil and military research is integrated into the overall development of explosive excavation. This research and development work is being conducted under the auspices of the U. S. Army Engineer Waterways Experiment Station Explosive Excavation Research Laboratory (EERL) located at Livermore, California. This organization was formed in 1962 as the Nuclear Cratering Group (NCG) to carry out the Corps of Engineers (OCE) portion of a joint agreement with the Atomic Energy Commission (AEC) to develop nuclear explosives for construction purposes. The AEC, through the Plowshare Division of the Lawrence Livermore Laboratory at Livermore, California, has been responsible for developing nuclear explosives, conducting nuclear cratering experiments, developing nuclear safety information, and developing methods for predicting the shape of the craters. The Army part of the program includes corollary chemical high-explosive cratering experiments, participation in the AEC's nuclear cratering experiments, and development of

Jan 1, 1997

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

In 1990, US mine production of barite increased 54.1 %. Barite consumption, sold or used by grinding plants, increased by 27.6%. Imports were about the same as 1989. World mine production in¬creased 12.3%, according to the US Bureau of Mines. The value of domestically produced barite, fob mine, decreased 12.7%, according to the Bureau. The declared value, cif US port, of all imported crude barite during the year 1990 increased from $40.27/t ($36.54 per st) in 1989 to $40.61/t ($36.84 per st). Nevada continued to be the leading producer of barite with 82% of the total, followed by Georgia and Missouri. It is estimated that 750/c, of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This includes barium chemicals and fillers in paper, plastics, and glass. Tonnage consumed in the drilling fluids market increased due to the higher average rig count during 1990. The average number of rotary rigs operating, (1010), was 16.2% more than the 1989 average of 869 in the US.

Jan 1, 1991

By Kenneth J. Miller

Froth flotation is one of the most actively pursued research and development areas in the coal preparation industry today. Many new types of flotation machines and processes are being developed and compared in an effort to handle the increased quantity of coal fines produced by finer grinding for greater liberation of ash- forming and sulfur-bearing mineral matter. Of the many new machines and processes under development for deep cleaning ultrafine coals, it is quite likely that many will not reach industrial use in the near future; in fact, it is quite likely that some never will. Therefore, it is the objective of this paper to select and describe a few of the new flotation machines and processes that appear to have reached a level of development that would suggest their eventual use on an industrial scale. It is probable, and doubtless will be argued, that some of the selections given in this paper should not have been included, while others should have, but the reader must understand that the author is restricted by the information available. And because most of the information available comes from those who are developing the equipment and/ or processes, it is often confusing and conflicting. Thus with a somewhat moderated plan, the author proposes to point out some in- congruities in the literature in the hope that such information might promote more independent study and perhaps explain the abundant promise versus the scant use of the new equipment and processes described.

Jan 1, 1988

By Larry Powell

Rend Lake is an Army Corps of Engineers reservoir located in Franklin and Jefferson Counties in south-central Illinois. The lake consists of 20,000 acres of water and 19,000 acres of public access land. The site attracts over two million visitors a year and is surrounded by campgrounds and other recreational facilities. The lake overlies the largest tonnage of low sulfur coal in the state. Coal is being removed beneath the lake from five mines operated by three coal companies. Currently high extraction mining operations are approaching low-lying, environmentally sensitive, and high-use recreational areas. Advanced planning to maximize coal extraction and minimize potential effects of subsidence requires the development of procedures to assess the impact of high-extraction mining on the land use of the area. The Bureau of Mines, the Corps of Engineers, and the coal companies have initiated research to assess the following proposed planning steps to ensure the maximum recovery of the coal resources while minimizing impacts to surface land use: 1) Establish a dialogue between the surface and mineral owners; 2) develop a geographic information system to aid in assessing existing land use and potential changes; 3) assess the potential effects of subsidence on drainage, wildlife habitats, and changes in land use prior to mining; 4) coordinate the mining displacements with surface activities to minimize disruption; and 5) develop appropriate mitigation plans before mining occurs.

Jan 1, 1986

By P. A. Hagerty

Biological treatment of metals-impacted water using sulfate reduction is a viable means of treatment that has been applied in pilot and full scale at numerous projects. One of the fundamental challenges with this type of treatment is the selection of an appropriate substrate to support the sulfate reduction process long-term. The substrate degradation products provide a carbon source and an electron donor for metabolism by sulfate-reducing bacteria and consequently organic characteristics are critical; however, the physical attributes of the substrate are equally critical to an efficient and optimized substrate mix. This paper explores the affect of particle size (a.k.a. grain size) of several substrate mixes on the treatment efficiency of sulfate reducing treatment systems. Substrate selection can be separated into two phases of evaluation, the primary selection phase and the secondary optimization phase. The primary selection phase considers such fundamental attributes as source availability, economics, bioavailability and longevity. These fundamental activities are conducted in order to identify potential candidate ingredients of the substrate mix which are regionally available, economically viable and consistent with the biogeochemical aspects of the project. Recent work has been conducted in the development of testing protocol for organic substrates to quantify bioavailability (Martinez Hernandez et al. 2010, Place et al. 2006) as part of the primary selection phase. Once the substrate ingredients have been selected based on the primary criteria, the mixture of these ingredients is then developed based on an optimization process, including consideration of the substrate ingredient?s particle size distribution.

Jan 1, 2011

By Guillermo P. Selas

Perhaps this is the first time that an analysis of the industrial minerals panorama has been made in Mexico for that type of commodities. Because the non-metallic minerals lack the glamour of the metallic minerals and are usually of less unit value than metallics, a comparative study of these commodities has seldom been attempted. Sulphur, fluorite, barite and few others are an exception. Consequently, the statistics on the lowest per unit value industrial minerals, such as limestone, dolomite, gravels, sands, etc., are usually scarce and not always accurate. The following, then, will be an attempt to show a general status of the industrial minerals in Mexico with due reservations regarding volumes and values. According to Kruger (1971), this group of minerals surprisingly very little known, and called non-metallics because the lack of metallic luster, is the largest group of the mineral kingdom. It constitutes perhaps 75% of all the mineral varieties. For the most part, these minerals are compounds of common acids, sulphides, hydroxides and two elements carbon and sulphur. The list of non-metallic minerals is therefore very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulphates and less commonly arsenates, chromates, molybdates, sulphides, tungstates and vanadates. The latter group and many of the oxides are sought usually for their metal content.

Jan 1, 1974

WELCOME to the world-class Cripple Creek district where gold exploration and production continue 95 years after the initial discovery. More than 21 million troy ounces of gold have been recovered, valued at greater than $7.8 billion using today's gold price ($371/oz). The Cripple Creek district is localized within and around the margins of a silica-undersaturated alkalic diatreme-intrusive complex. The diatreme appears to be comprised of three sub-basins: 1) a sub-basin east of the Cresson (Fig. 1); 2) a southwestern sub-basin between Victor and Cripple Creek; and 3) a northwestern sub¬basin within which the Globe Hill and Ironclad pits (Fig. 1) are located. The recognition of three separate basins was made by G. F. Loughlin and A. H. Koschmann (1935, Fig. 8) who prepared a contour map on the floor and walls of the composite Cripple Creek basin. The northwestern and southwestern sub-basins are apparent due to the discontinuous exposures of a partially exhumed ridge of Precambrian rocks (Fig. 1). The separation of the eastern and southwestern sub-basins was recognized in mine exposures where a fault-bounded ridge line extends from the vicinity of the Ajax mine toward the Precambrian "island" (Fig. 1).

Jan 1, 1986

By E. J. Garrison

A.C. Noble presents a clear and concise summary of the factors pertinent to a competent reserve evaluation of a mineral occurrence. However, I believe that he confuses the difference between a resource and a reserve. By definition, a reserve estimate includes all known economic, legal, mining, metallurgical and environmental factors impacting the recovery of the product(s) found in the deposit. A resource estimate, however, is an estimate of what is there - what is available for exploitation and should not include economic and other considerations. Only after defining the resource, its extent, location, physical and chemical properties, can an intelligent selection process begin of the extraction and processing technologies most appropriate to the circumstances encountered. The early and almost certainly inappropriate application of these often cookbook choices has probably lead many companies to walk away from good properties. (How many mines have been found in others rejects?) An example of the process is the early selection of metallurgical samples, after encouraging values are found in a few holes or surface samples, in an attempt to determine the economics of the prospect. Unfortunately, the sampler does not know how representative of the occurrence the sample is because he does not know what the deposit looks like. As a consequence, the property becomes saddled with a bad metallurgical sample that is often inappropriately used in evaluating the deposit which it does not represent.

Jan 1, 1994

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By P. Dhar, H. R. Kota, M. Thornhill

A very high-grade calcite deposit located in northern Norway consists of CaCO3 ore with minor silicate and sulphide impurities. Cationic (Tallow-1,3-diaminopropane, Duomeen T) collector has been used in the purification of calcite by flotation with an aim of achieving calcite concentrate for its use in value-added products in a variety of industries. The feasibility of sulphide flotation from calcite by this cationic collector has been initially judged from Hallimond flotation and zeta potential on pure mineral systems and the results illustrate the removal of sulphide from calcite ore at neutral pH region. The adsorption mechanism of diamine on both the sulphide minerals was found to be the same by zeta potential studies. The variations in zeta potential are in good agreement with the adsorption of diamine molecular and ionic species as a function of pH. FTIR studies also showed the adsorption of diamine species in agreement with the zeta potential and Hallimond flotation results. Furthermore, the removal of sulphide impurities with selective flotation by diamine collector was performed in bench-scale flotation with the calcite ore and the results indeed showed that the calcite concentrate could meet the quality requirements for its use in the paper industry for coating and filler purposes.

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By K. E. Robinson

During operation of tailings impoundments, water is lost through decanting, evaporation and seepage. Techniques have been developed to regulate or control each of these components. Collectively implemented, these techniques form the basis of tailings impoundment management. Regulation of the rate and level of decanting influences the size of a free water pond, and, thereby, the amount of evaporation and seepage, which are both area-dependent. Conversely, the encouragement of seepage and/or evaporation could also be used to reduce decanting requirements. Management of one of the components of a tailings impoundment's water balance is reflected in changes in the other components. The seepage component has the greatest potential impact on the environment, and consequently requires the closest scrutiny. Water percolating through tailings backfill transports heavy metals and other dissolved solids from the impoundment into the local groundwater regime. Depending on the seepage volume and concentration of contaminants, seepage from impoundments could exceed environmentally tolerable limits. Once mobilized, seepage-borne pollution is much more difficult to treat, mainly because of the problems in collecting the diffusive transportation medium. Pollution abatement measures relative to tailings impoundment seepage depend on seepage prevention or reduction. Seepage control measures include constructing barriers to flow, pump-back systems of interception and restricting the supply of water available for seepage.

Jan 1, 1987

By David Runnels

In September 1970, the Quebec Cartier Mining Company, started development of the Mount; Fright iron ore mine. The estimated ore reserve is in excess of 1,000,000,000 long tons with an average grade of 31.5% Fe. The run of mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production rate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material of which 50% is waste. The mine is located in the Province of Quebec, close to the Labrador border approximately 600 miles north-east of Montreal. The development of the mine necessitated the construction of an all electric one thousand housing unit townsite along with associated services such as a shopping center, swimming pool, arena, school, etc... A one-hundred mile long, 315 K.V. Dower line was built between the mine site and the Hydro-Quebec 735 K.V. existing power line between Churchill Falls and the Montreal area. The construction near the mine of a beneficiation plant was necessary to upgrade the 31.5% iron ore to a marketable product of 66% iron.

Jan 1, 1977

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By W. Joseph Schlitt

The use of plate and frame filter presses for dewatering cement copper at Kennecott' s Bingham Canyon precipitation plant is described. The dewatering process begins by periodically flushing a dilute copper slurry from cone precipitators to a rake thickener. The thickener underflows intermittently to an agitated surge tank which feeds the filter presses with a relatively constant slurry containing 10 to 20% solids. The presses operate with a three-stage cycle; loading, air blowing and discharging. Exothermic reactions occur during the air blow which cause actual drying as well as promoting dewatering via simple filtration. At the completion of the air blow, the presses are discharged onto a conveyor belt which transfers material to the load-out building for shipment to the smelter. An extended investigation was undertaken to relate moisture content in the filter cake to maximum press temperature, acidification of press feed, percent solids in the feed, and percent insol in the copper. Of these, press tempera¬ture and feed pH (3. 5 to 1. 0) have the greatest impact on drying. Because the discharged filter cake is hot and continues to undergo exothermic oxidation, significant drying occurs during subsequent handling so that a product containing 8 to 14% moisture is delivered to the smelter.

Jan 1, 1977

By Daniel F. Meyer

INTRODUCTION The Metropolitan Boston Transit Authority (MIA) Red Line has served greater Boston commuter needs from its Harvard Square terminus since its opening in 1912. Since then, the population of Boston's northwest area has increased substantially, and with this growth have come dramatic changes in the type and distribution of urban land uses, including the number of households, jobs, shopping and recreational opportunities; these changes have created a need for improved transportation. Extension of the Red Line to better serve these communities has been a topic of discussion for nearly 40 years. In November of 1977, the Urban Mass Transportation Administration (UMTA) granted the MBTA approval and funding for the Red Line Extension Project. With funding in place, the MBTA proceeded with final engineering and construction of the section from Harvard Square to Alewife. When completed, the Red Line Extension will add 3.2 miles of new track to the MBTA system. Estimated final cost is about $400 million. On October 3, 1978, the MBTA received bids for the construction of Project 091-105, Harvard Square to Porter Square Tunnels and Shafts, which is part of the overall Red Line Extension. The Joint Venture of Morrison-Knudsen, White, Mergentime was the low bidder at $47,478,600. Official award of the contract came on October 25, 1978, with Notice to Proceed given October 31, 1978. The contract called for construction of two independent parallel concrete-lined tunnels in rock, soft-ground and mixed-face

Jan 1, 1983

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014